Estimation of the energetic parameters associated with the aerobic degradation of quinoline by Comamonas acidovorans in continuous culture

An estimation of the true growth yields and maintenance coefficients for Comamonas acidovorans DSM 6426 under continuous cultivation on quinoline has been performed. The data were checked for consistency using available electron, carbon and nitrogen balances. The true biomass energetic yields, η_max, and energetic maintenance coefficients, m_e, were estimated using two models based on control of growth rate and control of substrate uptake rate, respectively. The estimations were converted to the various familiar true growth yield and maintenance units such as substrate-based (Y, m_S/X), oxygen-based (Y, m) and carbon dioxide-based (Y, m) units. For the complete mineralization of quinoline by C. acidovorans, values of η_max = 0.371 and m_e = 0·0426 h^?1 were obtained.     

Homogeneous and heterogeneous catalytic reactions in a cobalt oxide/graphite air electrode. Part IV. Mechanistic studies on a ring-disk carbon electrode in alkaline solution

The redox properties of HCoO on a glassy carbon electrode in the absence and presence of hydrogen peroxide have been investigated by using cyclic voltammetry and UV-Vis spectroscopy in alkaline solution. Corresponding rotating ring-disk experiments showed that the disk current increased by about 60% in the presence of HCoO, confirming the important role played by HCoO in the homogeneous decomposition of hydrogen peroxide.     

Solvent extraction of the trivalent lanthanides and yttrium by mixtures of 3,5-diisopropylsalicylic acid and neutral organophosphorus compounds

Neutral organophosphorus compounds containing a phosphoryl or thiophosphoryl group were found to cause appreciable synergistic shifts in the pH₅₀ values for the extraction of the trivalent lanthanides and yttrium from chloride media by solutions of 3,5-diisopropylsalicylic acid (DIPSA) in xylene. For the series of compounds with R = n-butyl, the synergistic effect increases in the order (RO)₃PS < (RO)₃PO < (RO)₂RPO < (RO)R₂PO < R₃PO. The synergistic effects are greater for lutetium(III) than for lanthanum(III) and, as a result, the separation across the lanthanide series (pH–pH) increases from only 0·17 pH unit for 0·25 M DIPSA alone to, for example, 0·85 pH unit for a mixture of 0·25 M DIPSA and 0·25 M triisobutylphosphine oxide (TIBPO). Mixtures of DIPSA and TIBPO give somewhat better separation factors between the light and middle lanthanide fractions (β = 3·0) than the commercial Versatic 10 acid (β = 2·6), and separation factors comparable to those of the latter extractant between the heaviest lanthanides (thulium to lutetium).     

Comment

Electrolytic manganese dioxide is dissolved in the mixed non-aqueous solvent dimethyl sulfoxide–sulfur dioxide (DMSO–SO₂) to form manganese disulfate as a final product. Sulfur dioxide does not change the oxidation state of the metal cations in DMSO–SO₂ solvent. However, oxidation of sulfur(IV) to sulfur(VI) is possible. The complete MnO₂ dissolution occurs in 50 min at a stirring speed of 650 rpm, pH 1, 0.2% solids concentration, 35 × 44 mesh particle size, and 36°C. IR and FTIR evidence has been presented in favor of the formation of SO, S₂O, (CH₃)₂S⁺ as intermediate species for the proposed mechanism. In the mixed non-aqueous solvent system the kinetics of leaching is controlled by a mass transport process. The equation 1–?α–(1–α)^2/3 = kt fits the experimental data very well. This is further supported by scanning electron micrographs, which show a product layer formation on the surface of the MnO₂ particle, and by the dependence of k on 1/r.     

Anaerobic biodegradability and toxicity of eucalyptus fiber board manufacturing wastewater

Wastewater from eucalyptus fiber board manufacturing (EFBM) was characterized and studied for its treatability by anaerobic digestion. The characteristics of the wastewater (in mg dm^?3), are as follows: COD (42 000), SS (550), SO (1200), PO.P (50), NH.N (15), VFA (710), phenol (20), p-cresol (125), tannin COD (1460) and pH 2.8. Approximately 60% of the COD is composed of carbohydrates. The continuous treatment of EFBM wastewater resulted in 93% COD removal and 78% COD methanogenized, with influent COD values of 20 g dm^?3 and OLR of 17 kg COD m^?3 d^?1. The biodegradation reached 94% of influent COD and 74% of influent ultraviolet absorbance (215 nm). EFBM wastewater supplied at 20 g COD dm^?3 (1:1 tap water diluted) caused 50% methanogenic toxicity, which did not disappear when tannins were removed by adsorption on PVP (polyvinylpyrrolidone). The toxicity decreased to 25% once the wastewater was autoxidized with air at high pH values. However, the effluent of the continuously fed column didn't show methanogenic toxicity, therefore the main toxic compounds in the wastewater were removed during anaerobic treatment.     

Intrinsic birefringence of nylon 6

Different values are reported in the literature for the intrinsic birefringence of the crystalline (Δn) and the amorphous (Δn) phases in nylon 6. Mostly, these values have either been determined by extrapolation (and then it is assumed that Δn = Δn) or calculated theoretically. In this study, intrinsic birefringence values Δn and Δn for nylon 6 were determined using the Samuels two-phase model which correlates sonic modulus with structural parameters. Three series of fiber samples were used: (1) isotropic samples of different degrees of crystallinity for estimation of E and E moduli at two temperatures. The following modulus values were obtained: 1.62 × 10⁹ and 6.66 × 10⁹ N/m² for 28.5°C, and 1.81 × 10⁹ and 6.71 × 10⁹ N/m² for ?20°C; (2) anisotropic, amorphous fiber samples for estimation of Δn = 0.076 and E = 1.63 × 10⁹ N/m² at 28.5°C; (3) semicrystalline samples of various draw ratios for estimations of Δn = 0.089 and Δn = 0.078. All measurements were carried out with carefully dried samples to avoid erroneous results caused by moisture.     

Removal of the tetravalent actinide thorium from solution by a biocatalytic system

The aim of this work was to study the effects of pH, a metal complexing reagent (citrate) and the concentration of substrate on the bioaccumulation of tetravalent actinides, using Th⁴⁺ as a model, by a phosphates-catalysed reaction. This yields HPO which precipitates with heavy metals as cell-bound metal phosphate. Poor removal of The from solution was observed, which is in accordance with the solution chemistry of the metal. A considerable improvement in the efficiency of thorium removal was obtained by incorporating ammonium acetate (NH₄Ac) into the solution. Although extensive deposition of polycrustaling NH₄UO₂PO₄ was observed previously by cells that had accumulated UO, no evidence for deposition of cstalline thorium phosphate was obtained by X-ray diffraction analysis. Examination by proton induced X-ray emission (PIXE) analysis. Examination by proton induced X-ray emission (PIXE) analysis showed a non-homogenous thorium deposit of variable phosphorous content.     

Ammoxidation of propylene by pulse reaction technique

The ammoxidation of propylene on Fe-Bi-P mixed oxide catalyst was studied at 500 °C by the pulse reaction technique, to examine the effects of P(P = 0–4) and P (P/P = 0–3) on the catalyst activity. Since the ammoxidation of propylene proceeds through consumption of oxygen from the catalyst even in the absence of oxygen, the reduction of catalyst progresses with the number of O₂-free pulse, losing its activity. In the presence of oxygen, however, the conversion of propylene and the selectivities of acrylonitrile, acetonitrile, CO₂, and CO vary with the pulse number, but settle to some steady values corresponding to P/P. It is also found that the conversion and the selectivities depend on the oxidation state of the catalyst, the latter also depending on P/P in the reactants, and that the catalyst working in the flow system may be being reduced to some extent.     

Denitrifying kinetics involving the distributed ratio of reductases

A suspended-growth batch reactor was used to denitrify synthetic wastewater containing various proportions of nitrate and nitrite. A competitive phenomenon between nitrate- and nitrite-reductase was studied utilizing various proportions of nitrate and nitrite in an anaerobic environment with a temperature of 30°C and methanol as carbon source. By using a non-linear regression technique, biokinetic constants of the maximum specific reduction rates of nitrate and nitrite (k₁, k₂) and the Monod half-saturation coefficients of nitrate and nitrite (K_s1, K_s2) for the proposed two-step denitrifying kinetics were 1·29 day^?1, 0·89 day^?1 and 14·3 mg NO-N dm^?3, 10.9 mg NO-N dm^?3, respectively. The result obtained from a series of chemostat studies indicated the Monod-type kinetic model was more accurate when the distributed ratio of nitrate- and nitrite-reductase in the proposed two-step denitrifying kinetics was taken into account.     

Oxidation of aqueous sulfur dioxide catalyzed by poly-4-vinylpyridine–Cu(II) complex. Part 1: Homogeneous phase oxidation

The oxidation of aqueous sulfur dioxide in the presence of polymer-supported copper(II) catalyst is also accompanied by homogeneous oxidation of aqueous sulfur dioxide catalyzed by leached copper(II) ions. Aqueous phase oxidation of sulfur dioxide of low concentrations by oxygen in the presence of dissolved copper(II) has therefore been studied. The solubility of SO₂ in aqueous solutions is not affected by the concentration of copper(II) in the solution. In the oxidation reaction, only HSO is the reactive S(IV) species. Based on this observation a rate model which also incorporates the effect of sulfuric acid on the solubility of SO₂ is developed. The rate model includes a power-law type term for the rate of homogeneous phase reaction obtained from a proposed free-radical chain mechanism for the oxidation. Experiments are conducted at various levels of concentrations of SO₂ and O₂ in the gas phase and Cu(II) in the liquid phase. The observed orders are one in each of O₂, Cu(II) and HSO. This suggests a first-order termination of the free radicals of bisulfite ions.     

Sensitivity analysis of catalytic conversion of n-C6

The present paper is a case study of an application of sensitivity analysis in chemical kinetics. Emphasis is laid upon chemical interpretation of sensitivity information and on identification of the most important model important model parameters. The kinetic model for reforming of C₆ hydrocarbons proposed by Mobil [14] is extended to the analysis of the behavior of n-hexane conversion in an adiabatic reactor. The importance of six initial conditions (feed composition and initial temperature) is analyzed by the computation of normalized first order sensitivity gradients (y/y) (δy_i/δy). The relative importance of 21 model parameters α_j is estimated by the computation of normalized sensitivity gradients of the type (α_j/y_i) (δy_i/δα_j). The influence of the decisive model parameters ΔH and ΔH (activation enthalpies of benzene hydrogenation and methyl cyclopentane isomerization, respectively) as well as operating parameters is presented. The problem of uncertainly in the value of ΔH and its influence on the model solution is also sown. Finally, some advantages of the application of normalized gradients of the explanation of process behavior are discussed.     

Elastic characteristics of branched-network polymers

The computed dependencies of elastic characteristics of branched-network polymers were obtained on the basis of the Takayanagi series model. The moduli ratio (λ) for branched-network and branched polymers increases as a result of an increase of the moduli ratio of network and branched phases (E/E) and the network phase fraction (V_net). The λ-increase as a function of V_net is larger than in the case of the E/E dependence. On the basis of computed dependencies, the experimental results for the radiation crosslinked SBS block copolymer were considered. The experimental results agree with the computed de-pendencies for the hetergeneous branched-network polymers with E/E ≈︁ 20. The influence of entanglements on the elastic characteristics of branched-network polymers is discussed. © 1996 John Wiley & Sons, Inc.     

Use of thermolysin metalloprotein affinity metal chromatography in the decontamination of actinide-bearing solutions

Thermolysin metalloprotein affinity metal chromatography (MAMC) has been shown to be effective for the removal and concentration of lanthanide and actinide ions from aqueous solution. Using solution of trivalent lanthanide ions of appropriate radii and of Th⁴⁺ and UO ions as models, the calciumbinding sites of immobilized thermolysin have shown appreciable potential for the decontamination of actinide-bearing waster solutions. The zinc-binding site of the affixed protein may also be used for the removal and concentration of divalent transition metal ions.     

Mass transport process for the adsorption of Cr(VI) onto water‐insoluble cationic starch synthetic polymers in aqueous systems

Dynamic adsorption behaviors between Cr(VI) ion and water‐insoluble amphoteric starches was investigated. It was found that the HCrO ion predominates over the initial pH ∼ 2–4, the CrO ion predominates over the initial pH ∼ 10–12, and both ions coexist over the initial pH ∼ 6–8. The sorption process occurs in two stages: the external mass transport process occurs in the early stage and the intraparticle diffusion process occurs in the long‐term stage. The diffusion coefficient of the early stage (D₁) is larger than that of the long‐term stage (D₂) for the initial pH 4 and pH 10. The diffusion rate of HCrO ion is faster than that of CrO ion for both processes. The D₁ and D₂ values are ∼ 1.38 × 10⁻⁷–10.1 × 10⁻⁷ and ∼ 0.41 × 10⁻⁷–1.60 × 10⁻⁷ cm² s⁻¹, respectively. The ion diffusion rate in both processes is concentration dependent and decreases with increasing initial concentration. The diffusion rate of HCrO ion is more concentration dependent than that of CrO ion for the external mass transport process. In the intraparticle diffusion process, the concentration dependence of the diffusion rate of HCrO and CrO ions is about the same. The external mass transport and intraparticle diffusion processes are endothermic and exothermic, respectively, for the initial pH 4 and pH 10. The k_d values of the external mass transport and intraparticle diffusion processes are ∼ 15.20–30.45 and ∼ −3.53 to −12.67 kJ mol⁻¹, respectively. The diffusion rate of HCrO ion is more temperature dependent than that of CrO ion for both processes. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2409–2418, 1999     

Several features of vinyl chloride–diallyl phthalate suspension copolymerization

Vinyl chloride–diallyl phthalate (VC–DAP) suspension copolymerization was carried out in a 5‐L autoclave and 200‐mL stainless steel vessel at 45°C. The apparent reactivity ratios of VC–DAP suspension copolymerization system were calculated as r_VC = 0.77 and r_DAP = 0.37. It shows that VC–DAP copolymer contains no gel when the feed concentration of DAP (f) is lower than a critical concentration (f_cr, inside the range of 0.466–0.493 mmol/mol VC at 80–85% conversion), the polymerization degree (DP) of copolymer increases with the increase of f and conversion. VC–DAP copolymer is composed of gel and sol fractions when f is larger than f_cr. The DP of sol fraction decreases as f increases, but the gel content and the crosslinking density of gel increase. The gel content also increases as conversion increases. The results also show that the index of polydispersity of molecular weight of sol changes with f, a maximum value appears when f is close to f_cr. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 156–162, 2000     

Tearing mode interlaminar fracture toughness of composite materials

The Simplified Split Cantilever Beam (SSCB) is proposed in this work and compared with the Split Cantilever Beam (SCB) to obtain the tearing mode interlaminar fracture toughness. The materials considered are single‐fiber system composites and interply hybrid composites. For interply hybrid composites, three different types of stacking sequence for SSCB specimens, which are [0/0//0],[0/0//0]. and [0/0//0], are tested to compare their suitability. Finite element analysis combined with a modified crack closure integral has been applied to separate the different components of the strain‐energy release rate. In addition, the method of compliance calibration was used to calculate Gc values. The effects of crack growth, initial crack length, specimen width, and number of glass fiber plies were also studied. The results show that SSCB testing has a more dominant Mode III component and more stable Gc values than SCB testing. For SSCB testing, the crack growth and the specimen width for the range considered have no clear effects on the interlaminar fracture toughness, but the initial crack length should be carefully selected to obtain corrected values. The tearing mode interlaminar fracture toughness of interply hybrid composites is higher than that of carbon/epoxy composites, and the three different types of stacking sequence considered are all suitable to approximate the Mode III interlaminar fracture toughness for interply hybrid composites.     

Forced oscillations in continuous flow stirred tank reactors with nonlinear step growth polymerization

The self-step growth polymerization of RA_f monomers in homogeneous, continuous flow stirred tank reactors (HCSTRs) is simulated under conditions of periodic feed concentration (with frequency ω and amplitude α). By having periodic operation, the polydispersity index of the polymer is found to increase by about 35% over the values at steady state. Periodic operation of HCSTRs is found to lead to gelation only for certain values of the frequency and the dimensionless residence time τ^*. Gelling envelopes have been obtained to give conditions under which HCSTRs should be operated. These envelopes can be described in terms of two critical dimensionless residence times, τ and τ such that nongelling operation is always ensured when τ^* < τ. For τ^* > τ, periodic operation always leads to gelation, and HCSTRs cannot be used. For τ < τ^* < τ, the gelling behavior is found to depend on the functionality f, amplitude α, and the dimensionless residence time τ^*.     

Electrochemical synthesis and properties of poly(3‐methylthiophene): Novel synthesis of poly(3‐methylthiophene) with pentachlorostannate and hexachloroantimonate

Poly(3‐methylthiophene) (P3‐MeT) doped with different anions were prepared electrochemically in the presence of tetraalkylammonium salts. The new poly(3‐methylthiophene) SnCl and SbCl (P3‐MeT SnCl₅ and P3‐MeT SbCl₆) were prepared electrochemically using tetra‐n‐butylammonium pentachlorostannate and tetra‐n‐butylammonium hexachloroantimonate as the supporting electrolytes. The effect of current density, salt concentration, reaction temperature, and the nature of solvents on the polymer yield and polymer conductivities have been investigated. Cyclic voltammetry of poly(3‐methylthiophene) has been examined at platinum electrode in 1,2‐dichloroethane medium containing n‐Bu₄NSnCl₅, Bu₄NSbCl₆, and Bu₄NClO₄ as the supporting electrolytes in the range of −1.0 to 1.7 V versus SCE in the presence and absence of 3‐methylthiophene. Electrical conductivity, magnetic susceptibility measurements, and structural determination by elemental analysis and infrared studies were also made. Scanning electron microscopy revealed a globular, branched, fibrous and a spongy, fibrous morphology of poly(3‐methylthiophene) SnCl, ClO, and SbCl, respectively. The thermal analysis of the polymers was also investigated. Possible causes for the observed lower conductivity of these polymers have also been discussed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 91–102, 1999     

Regression‐based model for elastic constants of 2D braided/woven open mesh angle‐ply composites

The elastic constants of closed mesh braided/woven fabrics are generally obtained from finite element analysis, fabric geometry model, and modified classical laminate plate theory. These models are complex and often impractical for industrial design purposes and do not address the cases of open mesh braided/woven fabrics. This paper proposes an alternative to existing models and software packages. Simple regression‐based empirical equations were developed to obtain E_x, E_y, G_xy, and ν_xy of braided/woven fabrics at any angle‐ply angle using the braid/weave unit cell volume fraction (V_f0), the fiber volume fraction (V_f), and the elastic constants of an equivalent angle‐ply laminate (E, E, G, ν). Design equation predictions were verified by comparing them to a previously validated modified classical laminate plate theory (CLPT) model using various fiber/resin combinations. Excellent agreement was found for each set of results. POLYM. COMPOS., 26:152–164, 2005. © 2005 Society of Plastics Engineers     

Study of crosslinking density in polydimethylsiloxane networks by DSC

A calorimetric study for estimating crosslinking densities of polydimethylsiloxane (PDMS) networks is presented. It involves the experimental determination of the heat capacities of the polymer with (C) and without (C) crosslinking. The theoretical basis of the method is described as well as the procedure used for the determination of the C_ps. The crosslinking densities of PDMS networks, determined by absorbency (swelling) measurments, using the Flory-Rehner equation, and by the method described here, are compared. The PDMS, obtained by the anionic synthesis of octamethylcyclotetrasiloxane, was analyzed by gel permeation chromatography and infrared spectroscopy. Separate samples of the polymer were further crosslinked at different network densities. The C_ps and the thermal stabilities were determined by DSC and TGA, respectively. The results indicate that the crosslinking density ratios of the polymer networks calculated by the relation ΔC/C are in reasonable agreement with those obtained from absorbency measurements. The crosslinking density can also be obtained from heat capacity measurments if the density of the network is known at the temperature that ΔC_p is obtained. © 1995 John Wiley & Sons, Inc.