首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
The aim of this work is to evaluate routes to upgrade recycled engineering plastics, especially mixed plastics with acrylonitrile–butadiene–styrene copolymers (ABS) as the major component. A core‐shell impact modifier was successfully used to improve the impact strength of blends of ABS and ABS/polycarbonate (PC) blends recycled from the automotive industry. However, the presence of other immiscible components like polyamide (PA), even in small amounts, can lead to a deterioration in the overall properties of the blends. A styrene–maleic anhydride (SMA) copolymer and other commercial polymer blends were used to promote the compatibilization of ABS and PA. The core‐shell impact modifier was again found to be an efficient additive with regard to the impact strength of the compatibilized ABS/PA blends. The results obtained with fresh material blends were quite promising. However, in blends of recycled ABS and glass‐fiber‐reinforced PA, the impact strength did not exhibit the desired behavior. The presence of poorly bonded glass fibers in the blend matrix was the probable reason for the poor impact strength compared with that of a blend of recycled ABS and mineral‐filled PA. Although functionalized triblock rubbers (SEBS–MA) can substantially enhance the impact strength of PA, they did not improve the impact strength of ABS/PA blends because the miscibility with ABS is poor. The possibilities of using commercial polymer blends to compatibilize otherwise incompatible polymer mixtures were also explored giving promising results. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2535–2543, 2002  相似文献   

2.
The effects of blend composition, melt viscosity of poly(acrylonitrile-butadiene-styrene) (ABS), and compatibilizing effect of poly(methyl methacrylate) (PMMA) on mechanical properties of ABS/polycarbonate (PC) blends at ABS-rich compositions were studied. As the content of PC was increased, impact strength and Vicat softening temperature (VST) were increased. As the melt viscosity of ABS was increased near to that of PC, finer distribution of dispersed PC phase and consequent enhanced impact strength and VST were observed. The compatibilizing effect of PMMA can be ascer-tained from the enhanced properties of ¼-inch notch impact strength, VST, tensilestrength, and the morphology observed by a scanning electron microscope. The improved adhesion of the ABS/PC interface by PMMA changed the fracture mechanism and reduced the notch sensitivity of blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 533–542, 1998  相似文献   

3.
The effect of three types of organoclays on the morphology and mechanical properties of lower critical solution temperature‐type poly(acrylonitrile‐butadiene‐styrene)/poly(methyl methacrylate) (ABS/PMMA) blends was investigated. Polymers were melt‐compounded with 2 and 4 wt % of clays using a twin‐screw extruder. X‐ray scattering and transmission electron microscopy revealed that the intercalation of the nanoclay in the hybrid nanocomposite was more affected by the polarity of the organoclay. Although the morphology of the blends varied by PMMA content, scanning electron microscopy showed smaller PMMA domains for the hybrid systems containing clay particles. Although good dispersion of the nanoclay through the ABS matrix and at the blend interface led to enhancement of tensile strength, the increment of the stiffness was more noticeable for nanocomposites including less polar organoclay. Well‐dispersed clay platelets increased the glass transition temperature. In addition, nanoscratching analysis illustrated an improvement in scratch resistance of ABS because of the presence of PMMA and organoclay. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012  相似文献   

4.
Polyamide (PA) and acrylonitrile/butadiene/styrene copolymer (ABS) may appear as a mixture in the recycled plastic stream. The incompatibility of these blends results in a blend with poor mechanical properties. The aim of this work is to partially convert the nitrile groups of the acrylonitrile/styrene copolymer (SAN) into oxazoline groups by reaction with aminoethanol (AE). Such modified SAN (SAN‐m) can react with the amine or carboxylic acid end groups of PA, and therefore used as compatibilizers for blends of PA with ABS. SAN‐m was found to reduce the SAN‐domain size in the PA/SAN‐blends. The initial acrylonitrile content of SAN‐m had a strong influence on the degree of conversion into oxazoline groups and on the compatibilizing effect. Mechanical properties of SAN‐m compatibilized PA/ABS blends were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 449–455, 2002  相似文献   

5.
The effects of the processing temperature on the morphology and mechanical properties at the weld line of 60/40 (w/w) polycarbonate (PC)/acrylonitrile–butadiene–styrene (ABS) copolymer blends were investigated. The influences of the incorporation of poly(methyl methacrylate) (PMMA) as a compatibilizer and an increase in the viscosity of the dispersed ABS domain phase were also studied. The ABS domain was well dispersed in the region below the V notch, and a coarse morphology in the core region was observed. When tensile stress was applied perpendicularly to the weld line, the fracture propagated along the weak region behind the weld part; there, the domain phase coalescence was significant because of the poor compatibility between PC and styrene–acrylonitrile (SAN). Phase coalescence became severe, and so the mechanical strength of the welded specimen decreased with an increasing injection‐molding temperature. The domain morphology became stable and the mechanical strength increased as the viscosity of the domain phase increased or some SAN was replaced with PMMA. That the morphology was well distributed behind the weld line and the mechanical properties of PC/ABS/PMMA blends were improved was attributed to the compatibilizing effect of PMMA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 689–699, 2005  相似文献   

6.
Polymer alloys have been used as an alternative to obtain polymeric materials with unique physical properties. Generally, the polymer mixture is incompatible, which makes it necessary to use a compatibilizer to improve the interfacial adhesion. Nylon 6 (PA6) is an attractive polymer to use in engineering applications, but it has processing instability and relatively low notched impact strength. In this study, the acrylonitrile–butadiene–styrene (ABS) triblock copolymer was used as an impact modifier for PA6. Poly(methyl methacrylate‐co‐maleic anyhydride) (MMA‐MA) and poly(methyl methacrylate‐co‐glycidyl methacrylate) (MMA‐GMA) were used as compatibilizers for this blend. The morphology and impact strength of the blends were evaluated as a function of blend composition and the presence of compatibilizers. The blends compatibilized with maleated copolymer exhibited an impact strength up to 800 J/m and a morphology with ABS domains more efi8ciently dispersed. Moderate amounts of MA functionality in the compatibilizer (~5%) and small amounts of compatibilizer in the blend (~5%) appear sufficient to improve the impact properties and ABS dispersion. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 842–847, 2003  相似文献   

7.
The mechanical and heat‐resistant properties of acrylonitrile–butadiene–styrene (ABS) binary and ternary blends were investigated. The relationship of compatibility and properties was discussed. The results show that poly(methyl methacrylate) (PMMA) and styrene–maleic anhydride (SMA) can improve the thermal properties of conventional ABS. The Izod impact property of ABS/PMMA blends increases significantly with the addition of PMMA, whereas that of ABS/SMA blends decreases significantly with the addition of SMA. Blends mixed with high‐viscosity PMMA are characterized by higher heat‐distortion temperature (HDT), and their heat resistance is similar to that of blends mixed with SMA. For high‐viscosity PMMA, from 10 to 20%, it is clear that blends appear at the brittle–ductile transition, which is related to the compatibility of the two phases. TEM micrographs show low‐content and high‐viscosity PMMA in large, abnormally shaped forms in the matrix. Compatibility between PMMA and ABS is dependent on both the amount and the viscosity of PMMA. When the amount of high‐viscosity PMMA varied from 10 to 20 wt %, the morphology of the ABS binary blends varied from poor to satisfactory compatibility. As the viscosity of PMMA decreases, the critical amount of PMMA needed for the compatibility of the two phases also decreases. SMA, as a compatibilizer, improved the interfacial adhesiveness of ABS and PMMA, which results in PMMA having good dispersion in the matrix. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2652–2660, 2002  相似文献   

8.
Acrylonitrile-butadiene-styrene terpolymer (ABS)/poly(methyl methacrylate) (PMMA) binary and ABS/PMMA/polycarbonate (PC) ternary blends were prepared using a corotating twin-screw extruder. Blend samples were annealed in a constant-temperature (215 and 225°C) hydraulic press up to 85 min. The changes in morphology and mechanical properties with annealing time were studied with transmission electron microscopys image analyzer, and tensile tester. With the increase in annealing time, the number of dispersed domains per cross-sectional area decreased and average domain size increased; this morphology coarsening became more responsible with time for the deterioration of blend properties. In ABS/PMMA/PC ternary blends, PMMA encapsulated PC in ABS matrix; this was predictable from the spreading coefficient calculation. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1531–1542, 1997  相似文献   

9.
Two types of core‐shell structured latexes, poly(methyl methacrylate‐co‐butadiene‐co‐styrene) (MBS) and poly(methyl methacrylate‐co‐methylphenyl siloxane‐co‐styrene) (MSiS) were used to modify recycled polycarbonate (PC) for the enhancement of toughness and flame retardancy. The impact strength of the modified PC blends was not improved after melt‐blending recycled PC with these two kinds of latexes, probably because the latex particles were not evenly dispersed in the PC matrix because of the incompatibility between PC and PMMA shell of the latexes. Addition of a compatibilizer, e.g. diglycidyl ether of bisphenol‐A or poly(styrene‐co‐maleic anhydride), can effectively enhance the toughening effect of recycled PC with core‐shell structured modifiers. The presence of compatibilizer in the blends reduces the interfacial tension and introduces a steric hindrance to coalescence, and thus enhances the interfacial adhesion between PC domain and PMMA shell, and improves the dispersion of core‐shell structured particles in the PC matrix. The ternary blends achieve a high impact resistance by cavitation of the particles, which relieves the triaxial stress and promotes massive shear yielding of the matrix, and then enables the matrix to fracture by the plane stress ductile tearing mode. Additionally, MSiS has a silicone‐based core and can effectively retard the combustion of recycled PC. The blends containing 7 wt % MSiS and 3 wt % compatibilizer can achieve a UL94 V‐0 rating in vertical burning test. We proposed that, during combustion, a fine dispersion of MSiS particles in the PC matrix facilitates the rapid migration of MSiS and formation of a uniform and highly flame resistant char barrier on the surface of the modified PC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010  相似文献   

10.
The morphology and mechanical properties of polycarbonate (PC) blends with rubber‐toughened styrene–maleic anhydride copolymer materials (TSMA) were investigated and compared with the properties of blends of PC with acrylonitrile–butadiene–styrene (ABS) materials. The PC/TSMA blends showed similar composition dependence of properties as the comparable PC/ABS blends. Polycarbonate blends with TSMA exhibited higher notched Izod impact toughness than pure PC under sharp‐notched conditions but the improvements are somewhat less than observed for similar blends with ABS. Since PC is known for its impact toughness except under sharp‐notched conditions, this represents a significant advantage of the rubber‐modified blends. PC blends with styrene–maleic anhydride copolymer (SMA) were compared to those with a styrene–acrylonitrile copolymer (SAN). The trends in blend morphology and mechanical properties were found to be qualitatively similar for the two types of copolymers. PC/SMA blends are nearly transparent or slightly pearlescent. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1508–1515, 1999  相似文献   

11.
制备不同配比的丙烯腈-丁二烯-苯乙烯(ABS)/苯乙烯-丙烯腈(SAN)/中粘度聚甲基丙烯酸甲酯(PMMA)合金,分别测试其缺口冲击强度、拉伸强度、热变形温度、熔体流动指数等,结果表明:ABS/SAN可以引发中粘度PMMA产生大量的银纹,从而大幅度提高共混物的冲击强度;引入中粘度PMMA可以提高ABS/SAN的耐热性能;添加中粘度PMMA,合金的流动性能呈现下降的趋势。  相似文献   

12.
Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6 30/70) blends were impact modified by addition of three kinds of maleated polystyrene‐based copolymers, i.e., maleated styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), maleated methyl methacrylate‐butadiene‐styrene copolymer (MBS‐g‐MA), and maleated acrylonitrile‐butadiene‐styrene copolymer (ABS‐g‐MA). The mechanical properties, morphology and rheological behavior of the impact modified PPO/PA6 blends were investigated. The selective location of the maleated copolymers in one phase or at interface accounted for the different toughening effects of the maleated copolymer, which is closely related to their molecular structure and composition. SEBS‐g‐MA was uniformly dispersed in PPO phase and greatly toughened PPO/PA6 blends even at low temperature. MBS‐g‐MA particles were mainly dispersed in the PA6 phase and around the PPO phase, resulting in a significant enhancement of the notched Izod impact strength of PPO/PA6 blends from 45 J/m to 281 J/m at the MBS‐g‐MA content of 20 phr. In comparison, the ABS‐g‐MA was mainly dispersed in PA6 phase without much influencing the original mechanical properties of the PPO/PA6 blend. The different molecule structure and selective location of the maleated copolymers in the blends were reflected by the change of rheological behavior as well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010  相似文献   

13.
HDP—PVC/ABS合金材料的研究   总被引:5,自引:0,他引:5  
研究了高聚合度聚氯乙烯(HDP-PVC)/ABS二元体系力学性能以及添加第三组分对合金材料力学性能的影响。结果表明:HDP-PVC/ABS配比为100/25时,共混物的综合性能好,体系能形成较完善的海岛结构;HDP-PVC/ABS/MBS体系中,MBS能改善多元体系的界面性能,提高合金材料的综合性能;HDP-PVC/ABS/CPE体系中,CPE能使形成网状结构和海岛结构共存的合金体系,提高合金材料  相似文献   

14.
The present work aims within the context of plastic recycling is to upgrade the properties of plastic waste particularly the two engineering plastics polycarbonate (PC) and poly (acrylonitrile‐butadiene‐styrene) (ABS) from electrical and electronic equipment. Recycled polycarbonate (RPC) and recycled poly (acrylonitrile‐butadiene‐styrene) (RABS) were obtained from E‐waste suppliers. RPC/RABS blends compatibilized with both maleic anhydride‐grafted polypropylene (MAP) and solid epoxy resin was prepared by microinjection molding. The effect of compatibilizer addition on the morphology and mechanical properties of RPC/RABS blends were analyzed. Further, to upgrade the mechanical and thermal properties two types of organically modified nanoclays closite 30B (C30B) and closite 15A (C15A) were incorporated into the optimized blend compositions. The effect of organoclay on the mechanical, thermal, and morphological properties of the RPC/RABS blend nanocomposites was investigated. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers  相似文献   

15.
Blends of poly(butadiene‐g‐poly(styrene‐co‐acrylonitrile) (ABS) with polycarbonate (PC) are some of the most successful multiphase materials, with applications in the automotive and electronics industries. The mechanical properties of the complete incompatible blends are mainly determined by the interaction between the poly(styrene‐co‐acrylonitrile) (S/AN) component of the ABS and the PC as well as through the dispersion of the elastomeric component poly(butadiene) in the thermoplastic S/AN‐matrix. The aim of our work is to optimize the modification process by the use of new substituted amino alcohols and amino phenols, as well as the use of a more efficient catalyst. Both reactive and non reactive compatibilization of polymer blends should be performed with the new ABS‐modifications.  相似文献   

16.
The ductile–brittle transition temperatures were determined for compatibilized nylon 6/acrylonitrile‐butadiene‐styrene (PA6/ABS) copolymer blends. The compatibilizers used for those blends were methyl methacrylate‐co‐maleic anhydride (MMA‐MAH) and MMA‐co‐glycidyl methacrylate (MMA‐GMA). The ductile–brittle transition temperatures were found to be lower for blends compatibilized through maleate modified acrylic polymers. At room temperature, the PA6/ABS binary blend was essentially brittle whereas the ternary blends with MMA‐MAH compatibilizer were supertough and showed a ductile–brittle transition temperature at ?10°C. The blends compatibilized with maleated copolymer exhibited impact strengths of up to 800 J/m. However, the blends compatibilized with MMA‐GMA showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2643–2647, 2003  相似文献   

17.
A series of acrylonitrile–butadiene–styrene (ABS) copolymer/poly(butylene terephthalate) (PBT)/acrylonitrile‐styrene‐glycidyl methacrylate (ASG) blends with various compositions were prepared and characterized in this study. When the fraction of ABS exceeds a critical value there is a rapid increase in notched impact strength of ABS/PBT blends no matter whether the compatibilizer ASG is present. By combining morphology observation and notched impact results, we found that the ductile‐brittle transition of the blends is closely related to the morphology inversion. The notched impact strength jumps from 15.9 to 33.4 kJ/m2 when phase inversion of ABS occurs at its fraction of 58 wt %. Accordingly, a possible toughening mechanism involved in the blends is proposed on the basis of a careful analysis of fracture energy, crack propagation behavior and fracture surface morphology. It is believed that the continuous ABS phase plays the critical role in toughening ABS/PBT blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46051.  相似文献   

18.
The development of the multiphase morphology of uncompatibilized blends of poly(butylene terephthalate) (PBT) and acrylonitrile–butadiene–styrene terpolymer (ABS) and PBT/ABS blends compatibilized with methyl‐methacrylate glycidyl‐methacrylate (MMA‐GMA) reactive copolymers during compounding in a twin‐screw extruder and subsequent injection molding was investigated. Uncompatibilized PBT/ABS 60/40 (wt %) and compatibilized PBT/ABS/MMA‐GMA with 2 and 5 wt % of MMA‐GMA showed refined cocontinuous morphologies at the front end of the extruder, which coarsened towards the extruder outlet. Coarsening in uncompatibilized PBT/ABS blends is much more pronounced than in the compatibilized PBT/ABS/MMA‐GMA equivalents and decreases with increasing amounts of the MMA‐GMA. For both systems, significant refinement on the phase morphology was found to occur after the blends pass through the extruder die. This phenomenon was correlated to the capacity of the die in promoting particles break‐up due to the extra elongational stresses developed at the matrix entrance. Injection molding induces coarsening of the ABS domains in the case of uncompatibilized PBT/ABS blends, while the reactive blend kept its refined phase morphology. Therefore, the compatibilization process of PBT/ABS/MMA‐GMA blends take place progressively leading to a further refinement of the phase morphology in the latter steps, owing to the slow reaction rate relative to epoxide functions and the carboxyl/hydroxyl groups. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 102–110, 2007  相似文献   

19.
The effect of the molecular weight and acrylonitrile (AN) content of the styrene–acrylonitrile copolymer (SAN) on the morphology, mechanical properties, and rheological properties of acrylonitrile–butadiene–styrene terpolymer/poly(methyl methacrylate) (ABS)/PMMA (60/40 by weight) blends were studied. When the AN content of matrix SAN (32%) was close to that of graft SAN (30%) AN, rubber particles existed separately. However, with matrix SAN having 35% AN, rubber particles showed tendency to agglomerate each other. With increasing molecular weight of matrix SAN, impact strength, ultimate elongation, and abrasion resistance of the blend generally increased. Yield strength increased with molecular weight at a constant AN content of matrix SAN, and it decreased with the decrease of AN content in spite of the increasing molecular weight of SAN. Melt properties, rather than the morphological and mechanical properties, were more sensitive to the AN content, rather than the molecular weight of matrix SAN. © 1994 John Wiley & Sons, Inc.  相似文献   

20.
Binary and ternary blends of PC, ABS, and PMMA were studied. The blends were produced from original and recycled materials by melt mixing in a wide range of compositions. Instrumented Charpy impact testing, tensile testing, rheology investigations, and electron microscopy were carried out to determine the relationship between the deformation and fracture behavior, blend composition, morphology, and processing parameters. Resistance against unstable crack propagation was evaluated using the concepts of J‐integral and crack‐tip‐opening displacement (CTOD). The transition from ductile elastic‐plastic to brittle‐linear elastic fracture behavior was observed in the case of PC/ABS/PMMA blend at 10% of PMMA. Reprocessing had only a slight influence on the deformation and fracture behavior of the recycled blends. The blends produced from recycled materials proved to be competitive with the original pure materials. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号