Microgelation of unsaturated polyester resins in the presence of poly(vinyl acetate) by static and dynamic light scattering

The partially cured unsaturated polyester (UPE)/styrene resins with various degrees of conversion lower than gel conversion blended with PVAc and 2‐fluorotoluene solvent were investigated using both static and dynamic light scattering (SLS and DLS). The solvent (i.e., 2‐fluorotoluene) is isorefractive with PVAc; thus, one sees only primary and partially cured UPEs in light‐scattering experiments. DLS was used to follow the variations of primary UPE and UPE microgel particle sizes, and SLS was used to follow the variations of UPE molecular weight, second virial coefficient (A₂), anisosymmetry (ρ_v), and differential index refraction (dn/dC) with degree of UPE conversion and PVAc concentration. The experimental data showed that, at a fixed degree of UPE/styrene conversion, increasing PVAc concentration in the UPE/styrene system caused decreases in dn/dC, A₂, ρ_v, and particle sizes of UPE microgels. These results suggest that mixing PVAc into UPE/styrene resins causes an increase in the compactness of UPE coils and favors intramolecular UPE/styrene cyclization in the early stage of curing. Thus A₂, ρ_v, and particle sizes of microgels decreased with increasing PVAc concentration. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1439–1449, 2001     

Phase separation in styrenated polyester resin containing a poly(vinyl acetate) low-profile additive

Scanning electron microscopy has been used to observe morphology in styrenated polyester resins containing poly(vinyl acetate) (PVA). Resins containing 8% PVA form composite spherical particles which occupy 35 vol% of the total material. It is concluded that these particles consist of resin sub-inclusions embedded in the continuous matrix of polyester resin. Increasing the PVA content to 16% results in a phase inversion: PVA forms the matrix, and the resin is present as spherical particles. These observations are interpreted with the aid of a ternary diagram.     

Reaction‐induced phase separation in poly(vinyl acetate)/polyester blend

In blends of unsaturated polyester (UP), poly (vinyl acetate) (PVAc), and styrene, a reaction‐induced phase separation occurs upon curing that is due to the crosslinking between styrene and the UP molecules. The evolution of the morphology was observed by optical microscopy on a heated stage. Light transmission was used in parallel to precisely detect the onset of phase separation and the formation of microvoids. Using Fourier transform IR spectroscopy in the same conditions, the conversions at phase separation and at microvoiding were evaluated. Phase separation occurs at a very low degree of conversion and microvoiding develops at around 60% of conversion. The final morphology of the blend was investigated by scanning electron microscopy. The relative influences of the cure temperature, the concentration in PVAc, and the molecular weight of PVAc were investigated. It was confirmed that the early stages of the reaction at high temperature determine the final morphology of the blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3877–3888, 2006     

Miscibility of biodegradable aliphatic polyester and poly(vinyl acetate) blends

We report miscibility behavior for synthetic biodegradable aliphatic polyester (BDP) and poly(vinyl acetate) (PVAc) blends by investigating their thermal, rheological, and mechanical properties. Two separate glass transition temperature peaks for the BDP/PVAc blends proved that these blend systems are immiscible. From the rheological measurement, the shear viscosity as a function of shear rate is observed to increase with increasing PVAc content in BDP/PVAc blends, since PVAc has a relatively high molecular weight compared to BDP. Moreover, BDP blends with 10 wt % PVAc have excellent mechanical properties. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1348–1352, 2000     

Thermal and mechanical properties of poly(methyl methacrylate) and ethylene vinyl acetate copolymer blends

A series of poly(methyl methacrylate) (PMMA) blends have been prepared with different compositions viz., 5, 10, 15, and 20 wt % ethylene vinyl acetate (EVA) copolymer by melt blending method in Haake Rheocord. The effect of different compositions of EVA on the physico‐mechanical and thermal properties of PMMA and EVA copolymer blends have been studied. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA) has been employed to investigate the phase behavior of PMMA/EVA blends from the point of view of component specific interactions, molecular motions and morphology. The resulting morphologies of the various blends also studied by optical microscope. The DSC analysis indicates the phase separation between the PMMA matrix and EVA domains. The impact strength analysis revealed a substantial increase in impact strength from 19 to 32 J/m. The TGA analysis reveals the reduction in onset of thermal degradation temperature of PMMA with increase in EVA component of the blend. The optical microscope photographs have demonstrated the PMMA/EVA system had a microphase separated structure consisting of dispersed EVA domains within a continuous PMMA matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Dynamical study on the late stage of demixing in poly(methyl methacrylate) and poly(vinyl acetate) blends

A dynamical study was made on demixing of an immiscible polymer blend, whose specimens were prepared by solvent casting and had very finely phase separated structures in the initial stage of the demixing. Light scattering experiments showed the applicability of a scaling rule to the later stage of the growth of phase separation structures. The demixing can be described by a scaling theory proposed by Furukawa.     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl acetate)

The results of the miscibility between the chemically similar polymers poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) published so far show inconsistent statements concerning miscibility. The problems may be due to differences in molecular weights, tacticity, and preparation methods of the polymers. This investigation was carried out by using either chloroform or tetrahydrofuran (THF) as solvent to prepare the blends, because to our knowledge, nobody has reported any tacticity effect of PMMA on the miscibility with PVAc. Therefore, in this article, different tactic PMMAs were used to mix with PVAc and their miscibility was studied calorimetrically. The results showed little effect of solvent and tacticity. PMMA and PVAc were determined to be almost completely immiscible because of the observation of two T_g's. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 35–39, 2004     

Diffusion of solvents in poly(vinyl acetate) and partially and fully hydrolyzed poly(vinyl alcohol)

Diffusivities of methyl acetate, methanol and water in poly(vinyl acetate) and fully and partially hydrolyzed poly(vinyl alcohol) have been measured by capillary column inverse gas chromatography and/or gravimetric sorption. Data from the literature have been used when available for comparison. Overall the diffusivities show good consistency in terms of their temperature and concentration dependences. The free‐volume model has been applied to all the data with excellent results. In most cases the dramatic changes in diffusivities with temperature and concentration can be captured using only a few experimental data points and two regression parameters. This demonstrates that the free‐volume theory is a valuable tool for the design of equipment for processing and devolatilization of polymer ? solvent systems. © 2013 Society of Chemical Industry     

Miscibility and hydrogen bonding in blends of poly(vinyl acetate) with phenolic resin

The miscibility of phenolic resin and poly(vinyl acetate) (PVAc) blends was investigated by differential scanning calorimeter (DSC), Fourier transform infrared spectroscopy (FT-IR) and solid state ¹³C nuclear magnetic resonance (NMR). This blend displays single glass transition temperature (T_g) over entire compositions indicating that this blend system is miscible in the amorphous phase due to the formation of hydrogen bonding between hydroxyl groups of phenolic resin and carbonyl groups of PVAc. Quantitative measurements on fraction of hydrogen-bonded carbonyl group using both ¹³C solid-state NMR and FT-IR analyses result in good agreement between these two spectroscopic techniques. According to the proton spin-lattice relaxation time in the rotating frame (T_1ρ^H), the phenolic/PVAc blend is intimately mixed on a scale less than 2-3 nm. Furthermore, the inter-association equilibrium constant and its related enthalpy of phenolic/PVAc blends were determined as a function of temperatures by infrared spectra based on the Painter-Coleman association model.     

Studies on the miscibility and phase structure in blends of poly(epichlorohydrin) and poly(vinyl acetate)

The miscibility of atactic poly(epichlorohydrin) (aPECH) with poly(vinyl acetate) (PVAc) was examined under two different conditions: (i) in dilute solution, using vicometeric measurements and (ii) as cast films, using differential scanning calorimetric (DSC) and FT-infrared spectroscopy. Phase separation on heating, i.e. lower critical solution temperature (LCST) behavior of the aPECH/PVAc blends was examined by the measurement of transmitted light intensity against temperature. From viscosity measurements, the Krigbaum-Wall polymer-polymer interaction (ΔB) was evaluated. The DSC results show that the aPECH/PVAc blends are miscible as evidenced by the observation of a single composition-dependent glass-transition temperature (T_g) which is well described by the Couchman and Gordon Taylor models. The Flory-Huggins interaction parameter (χ₁₂) calculated from the T_g-method was negative and equal to −0.01, indicating a relatively low interaction strength. The FT-IR results match very well with those of DSC. The cloud point phenomenon is thermodynamically driven but phase separation, once taken place, is diffusion controlled in normal accessible time.     

Curing kinetics of medium reactive unsaturated polyester resin used for liquid composite molding process

The cure kinetics of medium reactivity unsaturated polyester resin formulated for Liquid Composite Molding process simulation was studied by Differential Scanning Calorimetry (DSC) under isothermal conditions over a specific range of temperature. For isothermal curing reactions performed at 100, 110, and 120°C, several influencing factors were evaluated using the heat evolution behavior of curing process. We propose two‐ and three‐parameter kinetic models to describe the cure kinetics of thermoset resins. Comparisons of the model solutions with our experimental data showed that the three‐parameter model was the lowest parameter model capable of capturing both the degree of cure and the curing rate qualitatively and quantitatively. The model parameters were evaluated by a non‐linear multiple regression method and the temperature dependence of the kinetic rate constants thus obtained has been determined by fitting to the Arrhenius equation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Reduction of poly(vinyl chloride) with tri-n-butyltin hydride

Reduction of PVC with tributyl-tin-hydride (Bu₃SnH) was studied in order to optimize the method. The reactions were carried out in mixtures of xylene and tetrahydrofuran, chlorine content was determined by ¹H n.m.r. spectroscopy, and the melting behaviour by d.s.c. It was possible to obtain a product with less than 0.1% chlorine in less than 6 h. The ¹³C n.m.r. spectrum showed that the product contained about 4 methyl branches per 1000 monomer units and gave no evidence of chlorinated structures.     

Unsaturated polyester resin modified with poly(organosiloxanes). II. Acoustic emission study on glass-fiber-reinforced resin

This work aims to study the adhesion of an isophthalic acid based unsaturated polyester resin chemically modified by grafting copolymerization of a poly(organosiloxane) to the glass fiber. The failure mode of the single-edge notched tensile specimen, cut from pressed plates containing 50 wt % of nontreated and silane-treated milled glass fiber, was studied by acoustic emission (AE) technique. It was found that the aforementioned resin modification enhanced the adhesion between the fiber and the resin. This was suggested by a shift in the AE amplitude and energy toward higher values. On the other hand, the matrix modification had no significant effect if glass fiber with suitable unsaturated polyester resin (UP) sizing was incorporated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3280–3289, 2001     

Studies of polyester/chlorinated poly(vinyl chloride) blends

Chlorinated poly(vinyl chloride) (CPVC) was solution blended with poly(caprolactone) (PCL), poly(hexamethylene sebacate) (PHMS), poly(α-methyl-α-n-propyl-β-propiolactone) (PMPPL), poly(valerolactone) (PVL), poly(ethylene adipate), poly(ethylene succinate) and poly(β-propiolactone). From calorimetric glass transition temperature (T_g) measurements, it is concluded that CPVC is miscible with polyesters having a CH₂/COO ratio larger than three (PCL, PHMS, PMPPL and PVL). The Gordon-Taylor k parameter was also calculated and found equal to 1.0 and 0.56 for PCL/CPVC and PHMS/CPVC blends, respectively. From these values, it is concluded that CPVC gives a stronger interaction with polyesters than poly(vinyl chloride) due to its larger chlorine content.     

Characterization of poly(vinyl alcohol—acetate) by C n.m.r. and thermal analyses

Commercial poly(vinyl alcohol—acetate) copolymers were characterized by ¹³C n.m.r. spectroscopy in D₂O at 100.6 MHz and by differential scanning calorimetric measurements. N.m.r. spectra can be used for quantitative measurements of tacticity, vinyl alcohol—vinyl acetate composition, non-hydrolyzable branch content and blockiness of vinyl acetate residues. Conventional quality control tests for poly(vinyl alcohols) are recognized to be inadequate to account for all the important properties of these polymers. They have been augmented by thermal analyses for estimations of blockiness of alcohol and acetate residues. The crystal melting points of commercial poly(vinyl alcohols) vary significantly with thermal history of the samples. A standardized thermal procedure was used with observed melting temperatures to estimate either the degree of hydrolysis or the overall blockiness of the polymer. The equations used are based on theory but the procedures used industrially should best be regarded as semi-empirical because equilibrium melting points are not normally measured.     

Synthesis of high-molecular weight poly(vinyl alcohol) by low-temperature emulsifier-free emulsion polymerization of vinyl acetate and saponification

High-molecular weight (HMW) poly(vinyl alcohol) (PVA) was prepared via an emulsifier-free emulsion polymerization of vinyl acetate (VAc) using a redox initiation system in low temperatures, and the subsequent saponification with potassium hydroxide in methanol. The effect of the polymerization conditions on the conversion, molecular weight, and branching degree was investigated. PVA with maximum viscosity-average degree of polymerization (DP) of 8270 could be prepared by saponification of poly(vinyl acetate) (PVAc), with DP of 10,660 obtained at temperature of 10°C, monomer concentration of 30%, potassium persulfate molar ratio to monomer of 1/2000, agitation speed of 160 rpm. The conversion was above 90%. From the emulsifier-free emulsion polymerization of VAc in low temperature, PVAc with HMW and high linearity was effectively prepared, which might be useful for the preparation of high-strength and high-modulus PVA fiber. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Ionic conductivity of unsaturated polyester resin networks containing LiCIO4

Poly(ethylene oxide) (PEO) 400-maleate-isophthalate resins have been prepared and LiCIO₄ dissolved in the resins before crosslinking with 30% of styrene, vinylpyrrolidone or vinylpyridine. The DC conductivities of the resins were measured and found to increase in the order vinylpyridine 〈vinylpyrrolidone〉 styrene for the same [EO]/[Li⁺] ratio ( = 50). For the styrene system σ = 3 × 10^?6Scm^?1 at ambient temperatures and for the vinylpyridine system σ = 1 × 10^?7 Scm^?1. The T_gs of the system were also measured using dynamic mechanical thermal analysis and were found to be very close (257-260 K). The above sequence was therefore attributed to stronger site-binding of lithium ions at the more polar comonomers. An interpenetrating network (IPN) consisting of the styrene-polyester and incorporating 40% PEO 400 was also prepared with[EO]/[Li⁺]ratios of 20 and 50. These gave ambient temperature conductivities of 1 × 10^?5 and 3 × 10^?5 Scm^?1, respectively.     

Effects of poly(vinyl acetate) and poly(vinyl chloride‐co‐vinyl acetate) low‐profile additives on properties of cured unsaturated polyester resins. II. glass‐transition temperatures and mechanical properties

Three series of self‐synthesized poly(vinyl acetate)‐based low‐profile additives (LPAs), including poly(vinyl acetate), poly(vinyl chloride‐co‐vinyl acetate), and poly(vinyl chloride‐co‐vinyl acetate‐co‐maleic anhydride), with different chemical structures and molecular weights were studied. Their effects on the glass‐transition temperatures and mechanical properties for thermoset polymer blends made from styrene, unsaturated polyester, and LPAs were investigated by an integrated approach of the static phase characteristics, cured sample morphology, reaction kinetics, and property measurements. Based on Takayanagi mechanical models, the factors that control the glass‐transition temperature in each phase region of the cured samples and the mechanical properties are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3347–3357, 2003     

Fibrous membranes of cellulose acetate and poly(vinyl pyrrolidone) by electrospinning method: Preparation and characterization

Fibrous membranes of cellulose acetate (CA), poly(vinyl pyrrolidone) (PVP) and composite membranes of these polymers, were obtained by the electrospinning method. Using systematic method, the optimal conditions for preparation of fibrous membranes were found. Both CA and PVP a concentration of 8% weight was found. The CA was dissolved in a acetone:water solution, volume ratio 80 : 20 and the PVP is dissolved in ethanol:water solution, ratio volume 85 : 15. The flow rate for both polymers was 1.5 mL h^?1. The same applied voltage value and the distance between the needle and collection plate were for polymer both, 15 kV and 15 cm respectively. The morphology of fibrous membranes and composite membranes were evaluated by scanning electron microscopy (SEM). The CA fibers showed ribon morphology, while the PVP fibers were cilindric, in both cases with diameters in the micrometer range. Thermogravimetric analysis showed that CA had a complete degradation to 445°C, while the fibrous membranes PVP required a value of temperature for degradation of up to 571°C. Fibrous composite membrane PVP/CA/PVP shows a higher value of strain at break (%), and a lower value of tensile strength (MPa) compared to CA/PVP/CA. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010