Rheology of 1‐butyl‐3‐methylimidazolium chloride cellulose solutions. III. Elongational rheology

The elongational rheology of solutions of cellulose in the ionic liquid solvent 1‐butyl‐3‐methylimidazolium chloride ([Bmim]Cl) was measured at 80, 90, and 100°C; 8, 10, and 12 wt% cellulose; Hencky strains 5, 6, 7; and strain rates from 1 to 100 s^?1. Master curves were generated by shifting the elongational viscosity curves with respect to temperature and Hencky strain. Also, general master curves were generated by simultaneously shifting with respect to both temperatures and Hencky strain. From the Arrhenius plots of the temperature shift factors, the activation energy for elongational flow was determined. The elongational rheology of these solutions was elongational strain rate thinning similar to that of their shear behavior and polymer melts and they were also strain hardening. Both effects and the viscosity increased with cellulose concentration. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(ethylene terephthalate)–poly(caprolactone) block copolymer. I. Synthesis,reactive extrusion,and fiber morphology

A novel poly(ethylene terephthalate)–poly(caprolactone) block copolymer (PET–PCL) is synthesized in a reactive twin‐screw extrusion process. In the presence of stannous octoate, ring‐opening polymerization of ϵ‐caprolactone is initiated by the hydroxyl end groups of molten PET to form polycaprolactone blocks. A block copolymer with minimal transesterification is obtained in a twin‐screw extruder as a consequence of the fast distributive mixing of ϵ‐caprolactone into high melt viscosity PET and the short reaction time. The PET–PCL structure is characterized by IV, GPC, ¹H‐NMR, and DSC. Fully drawn and partially relaxed fibers spun from PET–PCL are characterized by WAXD and SAXS. A substantial decrease in the oriented amorphous fraction appears to be the major structural change in the relaxed fiber that provides the fiber with the desired stress–strain characteristics. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1858–1867, 1999     

Biodegradable poly(vinyl alcohol)‐graft‐ poly(ε‐caprolactone) comb‐like polyester: Microwave synthesis and its characterization

Poly(vinyl alcohol)‐initiated microwave‐assisted ring opening polymerization of ε‐caprolactone in bulk was investigated, and a series of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) (PVA‐g‐PCL) copolymers were prepared, with the degree of polymerization (DP) of PCL side chains and the degree of substitution (DS) of PVA by PCL being in the range of 3–24 and 0.35–0.89, respectively. The resultant comb‐like PVA‐g‐PCL copolymers were confirmed by means of FTIR, ¹H NMR, and viscometry measurement. The introduction of hydrophilic backbone resulted in the decrease in both melting point and crystallization property of the PVA‐g‐PCL copolymers comparing with linear PCL. With higher microwave power, the DP of PCL side chains and DS of PVA backbone were higher, and the polymerization reaction proceeded more rapidly. Both the DP and monomer conversion increased with irradiation time, while the DS increased first and then remained constant. With initiator in low concentration, the DP and DS were higher, while the monomer was converted more slowly. Microwaves dramatically improved the polymerization reaction in comparison of conventional heating method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3973–3979, 2007     

Transesterification in homogeneous poly(ε‐caprolactone)–epoxy blends

Transesterification has been investigated in poly(ε‐caprolactone) (PCL)–epoxy blends. In the hot melt process, the hydroxyl on diglycidyl ether of bisphenol‐A (DGEBA) monomers is too low to give a noticeable transesterification reaction. In the postcure process, model reactions reveal that the hydroxyls from a ring‐opening reaction are able to react with the esters of PCL. In the meantime, the PCL molecular weight decrease and its distribution becomes broader. Nuclear magnetic resonance spectra reveal that fraction of the tertiary hydroxyls converts to secondary hydroxyls. In the cured DGEBA–3,3′‐dimethylmethylene‐di(cyclohexylamine)–PCL blend, a homogeneous morphology is achieved. PCL segments are grafted onto the epoxy network after postcuring and result in the lower T_g observed in the differential scanning calorimetry thermogram. A higher transesterification extent also results in broader transition peaks by dynamic mechanical analysis. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 75–82, 1999     

Solubilization of graphene flakes through covalent modification with well‐defined azido‐terminated poly(ε‐caprolactone)

A well‐defined poly(ε‐caprolactone) (PCL) with terminal azido group was prepared. Grafting‐on reaction between the azido‐terminated PCL (N₃? PCL) and ultrasonication‐assisted exfoliated graphene flakes (GF) was carried out to obtain PCL‐grafted‐GF (PCL‐g‐GF) which showed good dispersibility in a wide variety of organic solvents. Gel permeation chromatography, ¹H NMR, IR, Raman, UV‐vis, and TEM measurements indicated that PCL macromolecules were covalently introduced on the surface of GF without disrupting the structure of GF. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41569.     

Effect of dialcohols on properties of poly(ethylene 2,6‐naphthalate) copolymers

Properties of poly(ethylene 2,6‐naphthalate) (PEN) and its copolymers containing diethylene glycol (DEG), propanediol (PD), butanediol (BD), and bisphenol A ethoxylate (BSA) were investigated. The copolymer composition was determined by ¹H‐NMR spectroscopy. It has a higher value than the feed composition due to the high volatility of ethylene glycol (EG). The melting temperature of the copolymers was gradually depressed with the increase of dialcohol in the composition. The complex viscosity of the copolymers did not depend on the molecular weight, but on the chemical structure. The complex viscosity of the copolymers containing 3 mol % of DEG, BD, and 5 mol % of BD was lower than that of PEN, and the mechanical properties were similar with the value of PEN. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2900–2905, 1999     

Crystallization kinetics of thermosetting polymer blends of poly(ε‐caprolactone) and unsaturated polyester resin

A study has been made of the isothermal crystallization kinetics of poly(ε‐caprolactone) (PCL) in partially miscible crosslinked polyester resin (PER)/PCL blends by using differential scanning calorimetry (DSC). For comparison, miscible blends of PCL with uncured polyester resin, i.e., oligoester resin (OER), were also investigated. The overall crystallization rate of PCL remarkably decreased with the addition of amorphous component, OER or PER. The kinetic rate constant K_n decreased sharply for both the OER/PCL blends and the crosslinked PER/PCL blends with decreasing PCL concentration. The mechanism of nucleation and geometry of the growing PCL crystals was not remarkably affected by the incorporation of OER, but changed considerably with the addition of PER. However, the overall crystallization rate of PCL in the crosslinked PER/PCL blends was much higher compared with the corresponding uncured OER/PCL blends, which is attributable to the phase‐separated structure and the reduced miscibility in the crosslinked blends. According to the nucleation and growth theories, the nucleation process was considered to be the rate controlling step in the crystallization. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 322–327, 1999     

Cyclohexene oxide mid‐chain functional macromonomer of poly(ε‐caprolactone): Synthesis,characterization, and photoinitiated cationic homo‐ and copolymerization

In this study, a novel well‐defined epoxy mid‐chain functional macromonomer of poly(ε‐caprolactone) (PCL) has been synthesized by ring‐opening polymerization (ROP) of ε‐caprolactone (ε‐CL) and epoxidation on workup with 3‐chloroperoxybenzoic acid. The ROP of ε‐CL monomer in bulk at 110°C, by means of a dihydroxy functional initiator namely, 3‐cyclohexene‐1,1‐dimethanol in conjunction with stannous‐2‐ethylhexanoate, (Sn(Oct)₂), yielded a well‐defined PCL with a cyclohexene mid‐chain group. The epoxidation of the cyclohexene (CH) mid‐chain group of PCL was performed using 3‐chloroperoxybenzoic acid. GPC, IR, and ¹H‐NMR analyses revealed that a low‐polydispersity macromonomer of PCL with the desired cyclohexene oxide (CHO) functionality at the mid‐chain was obtained. The photoinduced cationic polymerizations of this macromonomer yielded comb‐shaped and graft copolymers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol) block copolymers prepared by a salicylaldimine‐aluminum complex

A series of poly(?‐caprolactone)‐b‐poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights were synthesized with a salicylaldimine‐aluminum complex in the presence of monomethoxy poly(ethylene glycol). The block copolymers were characterized by ¹H NMR, GPC, WAXD, and DSC. The ¹H NMR and GPC results verify the block structure and narrow molecular weight distribution of the block copolymers. WAXD and DSC results show that crystallization behavior of the block copolymers varies with the composition. When the PCL block is extremely short, only the PEG block is crystallizable. With further increase in the length of the PCL block, both blocks can crystallize. The PCL crystallizes prior to the PEG block and has a stronger suppression effect on crystallization of the PEG block, while the PEG block only exerts a relatively weak adverse effect on crystallization of the PCL block. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis,crystallinity and degradation properties of biodegradable poly[(sebacic anhydride)‐co‐caprolactone] triblock copolymers

BACKGROUND: A series of novel biodegradable poly[(sebacic anhydride)‐co‐caprolactone] (PSA‐co‐PCL) triblock copolymers were prepared by melt condensation of acylated PSA and monofunctional hydroxyl‐terminated PCL prepolymers. These copolymers could be used as novel drug delivery carriers with expected good drug permeability due to the PCL component. The degradation rate and mode can be modulated by varying the ratio of monomers in the copolymer. RESULTS: The homopolymers and copolymers were characterized using ¹H NMR, gel permeation chromatography and differential scanning calorimetry (DSC). ¹H NMR confirmed the formation of triblock copolymers that comprise a middle PSA block and two side PCL blocks. DSC revealed that the melting temperature and degree of crystallinity for both sebacic anhydride (SA) and caprolactone (CL) components are strongly composition dependent, implying the hindrance effect of the two components on the crystallinity. In vitro degradation experiments showed that the mass loss is significantly accelerated for samples in base buffer solution and more rapid for the copolymers with a higher SA content. Scanning electron microscopy revealed that for SA‐rich copolymer, PSA(80 wt%)‐co‐PCL, surface erosion dominated the degradation mode of the sample. In contrast, for CL‐rich copolymer, PSA(20 wt%)‐co‐PCL, a micropore structure developed at a degradation time of 155 h along the edges of the sample, owing to the hydrolysis of SA. CONCLUSION: It is concluded that the rate and mode of degradation of these copolymers can be tuned by varying the composition of the copolymers. Copyright © 2007 Society of Chemical Industry     

Novel biodegradable amphiphilic poly(ε‐caprolactone)/poly(N‐vinylpyrrolidone) blends via successive in situ polymerizations

In this study, biodegradable blends of poly(ε‐caprolactone) (PCL) and poly(N‐vinylpyrrolidone) (PVP) were prepared by a new strategy in the following steps: (1) free radical polymerization of N‐vinyl‐2‐pyrrolidone (NVP) in ε‐caprolactone (CL); (2) ring‐opening polymerization of ε‐caprolactone in the presence of PVP to obtain the target blends. The structure of the blends was confirmed by FTIR and ¹H NMR, and the molecular weight of PCL and PVP were determined by GPC. SEM study revealed that this polymerization method could decrease the disperse phase size and improve the interphase when compared with solution‐blending method. The phase inversion occurred when PVP content was 15–20 wt %. Subsequently, the PCL sphere dispersed in PVP matrix and its size decreased with the increase of PVP content. The contact angle results showed that PVP has a profound effect on hydrophilic properties of PCL/PVP blends. PCL/PVP blends are believed to be promising for drug delivery, cell therapy, and other biomedical applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The use of crosslinking promoters in the γ‐radiolysis of poly(tetrafluoroethylene‐co‐perfluoromethylvinyl ether).I

Incorporation of 1 wt % of triallyl isocyanurate (TAIC) significantly enhanced the radiation crosslinking of the perfluoroelastomer, poly(tetrafluoroethylene‐co‐perfluoromethylvinyl ether) (TFE/PMVE). The dose for gelation was lowered by 70% with the presence of TAIC. The additive also improved the tensile properties of TFE/PMVE both before and after crosslinking by irradiation. Higher radical yields were obtained with the presence of TAIC at 77 K, indicating the crosslinking promoter was acting as a radical trap. ESR studies showed that radiolysis of TAIC and subsequent photobleaching cleaved an allyl branch from the ring structure. Upon thermal annealing, an allyl radical on the TAIC molecule was observed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 169–175, 1999     

Correlation of the melt rheological properties with the foaming behavior of immiscible blends of poly(2,6‐dimethyl‐1,4‐phenylene ether) and poly(styrene‐co‐acrylonitrile)

Immiscible blends of poly(2,6‐dimethyl‐1,4‐phenylene ether)/poly(styrene‐co‐acrylonitrile) (PPE/SAN) were batch‐foamed using CO₂ as a blowing agent as a function of foaming temperature, foaming time, and blend composition. Evaluation of the resulting cellular morphology revealed an enhanced foamability of SAN with PPE contents up to 20 wt% as indicated by a similar volume expansion but a significantly reduced mean cell size. This behavior is related to a heterogeneous nucleation activity by the dispersed PPE phase. A further increasing PPE content, however, leads to increasing foam densities as well as nonuniform foam morphologies. The changes in the foaming behavior can be correlated with the melt rheological properties and the corresponding blend morphology. Shear‐rheological investigations revealed an onset of percolation of the dispersed PPE phase between 20 and 40 wt%, and a transition towards cocontinuity at 60 wt%. The materials response under uniaxial elongational flow, as assessed by Rheotens measurements, revealed an increase in elongational viscosity scaling with the PPE content, similar to the shear data. However, the strain hardening behavior was reduced by increasing PPE contents and, at 20 wt%, the drawability revealed a significant drop‐both phenomena limiting the foamability of polymers. In summary, the present study discusses fundamental aspects of foaming immiscible PPE/SAN blends. POLYM. ENG. SCI., 48:2111–2125, 2008. © 2008 Society of Plastics Engineers     

Recycling of poly(ethylene terephthalate) into closed‐cell foams

The increase of the elongational viscosity of recycled poly(ethylene terephthalate) (PET) is investigated with the aim of producing closed‐cell foams by means of a cost‐effective reactive extrusion technique. A recycled PET grade containing controlled contamination levels of polyvinyl chloride (PVC) and poylethylene (PE) is selected, and compared with virgin bottle‐grade PET as a reference. Reactive processing with a tetrafunctional epoxy additive induces randomly branched molecules with a lower degree of branching in recycled PET than in virgin PET, as shown by a molecular structure analysis. The corresponding increase in elongational viscosity is related to foaming experiments performed using supercritical CO₂ in a pressurized vessel. Observations of foam microstructures reveal that modified virgin PET forms closed‐cell structures under a large variety of foaming conditions, as opposed to unmodified virgin and recycled PET, which collapse as a result of insufficient elongational resistance. Closed‐cell foams are also obtained using modified recycled PET, providing that the temperature at which the pressure is released is lowered to 260°. Recycling of PET into closed‐cell foams is thus achieved, although the processing window is slightly reduced compared to virgin PET.     

Synthesis and characterization of poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers by combined ring‐opening polymerization and cross‐coupling processes

2,5‐Dibromo‐1,4‐(dihydroxymethyl)benzene was used as initiator in ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate (Sn(Oct)₂) catalyst. The resulting poly(ε‐caprolactone) (PCL) macromonomer, with a central 2,5‐dibromo‐1,4‐diphenylene group, was used in combination with 1,4‐dibromo‐2,5‐dimethylbenzene for a Suzuki coupling in the presence of Pd(PPh₃)₄ as catalyst or using the system NiCl₂/bpy/PPh₃/Zn for a Yamamoto‐type polymerization. The poly(p‐phenylenes) (PPP) obtained, with PCL side chains, have solubility properties similar to those of the starting macromonomer, ie soluble in common organic solvents at room temperature. The new polymers were characterized by ¹H and ¹³C NMR and UV spectroscopy and also by GPC measurements. The thermal behaviour of the precursor PCL macromonomer and the final poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers were investigated by thermogravimetric analysis and differential scanning calorimetry analyses and compared. Copyright © 2004 Society of Chemical Industry     

Preparation and properties of composites based on melamine‐formaldehyde foam and nano‐Fe3O4

In this work, a novel melamine‐formaldehyde‐Fe₃O₄ foam was prepared from a mixture containing melamine‐ethanolamine‐formaldehyde resin, melamine‐glycol‐formaldehyde resin and carboxylated Fe₃O₄ nanoparticles by microwave foaming method. The two resins were characterized by ¹³C‐NMR, respectively. The structures of foams, mechanical and fire‐retardant properties were experimentally characterized separately by scanning electron microscopy, universal testing machine, limit oxygen index, thermogravimetry‐differential thermal analysis, and Fourier transform infrared spectra. The effects of the resin viscosity, emulsifier, nucleating agent, curing agent, silicone oil, microwave heating time and blowing agent on the structure of foam were investigated. Results showed that the properties of foam were decided by not only the molecular structure but also structure of foam, and the carboxylated Fe₃O₄ nanoparticles can improve the toughness and flame retardant properties of magnetic foam obviously from both aspects. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2688–2697, 2013     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure and melt rheology of long‐chain branching polypropylene/clay nanocomposites

Long‐chain branching polypropylene (LCB‐PP)/clay nanocomposites were prepared by melt blending in a twin‐screw extruder. The microstructure and melt rheology of these nanocomposites were investigated using x‐ray diffraction, transmission electron microscopy, oscillatory shear rheology, and melt elongation testing. The results show that, the clay layers are intercalated by polymer molecular chains and exfoliate well in LCB‐PP matrix in the presence of maleic anhydride grafted PP. Rheological characteristics, such as higher storage modulus at low‐frequency and solid‐like plateau in tan‐ω curve, indicate that a compact and stable filler network structure is formed when clay is loaded at 4 phr (parts per hundred parts of) or higher. The response of the nanocomposite under melt extension reveals an initial decrease in the melt strength and elongational viscosity with increasing clay concentration up to 6 phr. Later, the melt strength and elongational viscosity show slight increases with further increasing clay concentration. These results might be caused by a reduction in the molecular weight of the LCB‐PP matrix and by the intercalation of LCB‐PP molecular chains into the clay layers. Increases in the melt strength and elongational viscosity for the nanocomposites with decreasing extrusion temperature are also observed, which is due to flow‐induced crystallization under lower extrusion temperature. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Starch‐g‐polycaprolactone copolymerization using diisocyanate intermediates and thermal characteristics of the copolymers

Starch‐g‐polycaprolactone copolymers were prepared by two‐step reactions. The diisocyanate‐terminated polycaprolactone (NCO–PCL) was prepared by introducing NCO on both hydroxyl ends of PCL using diisocyanates (DI) at a molar ratio between PCL and DI of 2:3. Then, the NCO–PCL was grafted onto corn starch at a weight ratio between starch and NCO–PCL of 2:1. The chemical structure of NCO–PCL and the starch‐g‐PCL copolymers were confirmed by using FTIR and ¹³C‐NMR spectrometers, and then the thermal characteristics of the copolymers were investigated by DSC and TGA. By introducing NCO to PCL (M_n : 1250), the melting temperature (T_m ) was reduced from 58 to 45°C. In addition, by grafting the NCO–PCL (35–38%) prepared with 2,4‐tolylene diisocyanate (TDI) or 4,4‐diphenylmethane diisocyanate (MDI) onto starch, the glass transition temperatures (T_g 's) of the copolymers were both 238°C. With hexamethylene diisocyanate (HDI), however, T_g was found to be 195°C. The initial thermal degradation temperature of the starch‐g‐PCL copolymers were higher than that of unreacted starch (320 versus 290°C) when MDI was used, whereas the copolymers prepared with TDI or HDI underwent little change. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 986–993, 2000     

Unsaturated polyester–poly(ε‐caprolactone) hybrid nanocomposites: Thermal–mechanical properties

This paper reports on the thermal behavior and mechanical properties of nanocomposites based on unsaturated polyester resin (UP) modified with poly(ɛ‐caprolactone) (PCL) and reinforced with an organically modified clay (cloisite 30B). To optimize the dispersion of 30B and the mixing of PCL in the UP resin, two different methods were employed to prepare crosslinked UP–PCL‐30B hybrid nanocomposites. Besides, two samples of poly(ɛ‐caprolactone) of different molecular weight (PCL2: M_n = 2.10³g.mol⁻¹ and PCL50: M_n = 5.10⁴g.mol⁻¹) were used at several concentrations (4, 6, 10 wt%). The 30B concentration was 4 wt% in all the nanocomposites. The morphology of the samples was studied by scanning electron microscopy (SEM). The analysis of X‐ray patterns reveals that intercalated structures have been found for all ternary nanocomposites, independently of the molecular weight, PCL concentration and the preparation method selected. A slight rise of the glass transition temperature, T_g, is observed in UP/PCL/4%30B ternary nanocomposites regarding to neat UP. The analysis of the tensile properties of the ternary (hybrid) systems indicates that UP/4%PCL2/4%30B nanocomposite improves the tensile strength and elongation at break respect to the neat UP while the Young modulus remains constant. POLYM. COMPOS., 35:827–838, 2014. © 2013 Society of Plastics Engineers