Casting solvent effect on crystallization behavior of poly(vinyl acetate)/poly(ethylene oxide) blends: DSC study

Poly(vinyl acetate) (PVAc)/poly(ethylene oxide) (PEO) blends were prepared by casting from either benzene or chloroform. The solvent effects on the crystallization behavior and thermodynamic properties of the blends were studied by the differential scanning calorimeter (DSC). Two grades of PEO with different molecular weights (PEO200 with M_w = 200,000 g/mol and PEO2 with M_n = 2000 g/mol) were used in this work. The thermal analysis revealed that the blends cast from either benzene or chloroform were miscible in the molten state. The crystallization of PEO in the benzene-cast blends was more easily suppressed than it was in the chloroform-cast blends. Furthermore, the benzene-cast blends showed a greater negative value of Flory-Huggins interaction parameter than those cast from chloroform in the PVAc/PEO200 poly-blend system. It was supposed that the benzene-cast blends had more homogeneous morphology. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 411–421, 1997     

Phase Behaviour of Poly(ethylene oxide)/Poly(styrene-co-maleic anhydride) Blends

Thermal behaviour and morphology of blends of poly(ethylene oxide) (PEO) and poly(styrene-co-maleic anhydride) (SMA) prepared by the coprecipitation technique were studied by means of differential scanning calorimetry, optical microscopy and thermogravimetry. SMA containing 25wt% maleic anhydride (MA) was found to be miscible with PEO when the SMA content was greater than 80%. The melting temperature and crystallinity depended on the composition of the blend. SMA appears to segregate interlamellarly during the isothermal crystallization of PEO. The thermal stability of blends was enhanced and was higher than that of pure PEO and SMA. © of SCI.     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Rheological study on poly-D(-)(3-hydroxybutyrate) and its blends with poly(ethylene oxide)

Aspects of thermal, morphological, and rheological properties of biodegradable poly-D(-)(3-hydeoxybutyrate) (PHB) blended with poly(ethylene oxide) (PEO) have been studied. Thermal properties and morphology of the blends were examined by scanning electron microscopy and differential scanning calorimetry, respectively. A rotational theometer with parallel plate geometry was also adopted to investigate the rheological properties of these blends. In addition, dynamic ciscoelasticity was measured by a Rheovibron as functions of time and temperature. From these measurements, PHB and PEO were observed to be miscible in the melt state. In the case of the blend systen 80/20 PHB/PEO by weight, the vacant domains of the PHB were filled with PEO particles, and this morphological state enhanced the rheological properties. Furthermore, PHB and its blends were found to have high crystallinities, but to have unstable thermal behavior about T_m.     

Ionomeric blends of poly(ethylene oxide) with poly(styrene‐co‐maleic anhydride) ionomer: Miscibility,crystallization, and melting behavior

The miscibility and crystallization behavior of poly(ethylene oxide) (PEO) and poly(styrene‐co‐maleic anhydride) ionomer (SMAI) blends were studied by the dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). This study has demonstrated that the presence of ion–dipole interactions enhances the miscibility of otherwise immiscible polymers in the PEO and high molecular weight poly(styrene‐co‐maleic anhydride) (SMA). The effect of ion–dipole interactions on enhancing miscibility is confirmed by the presence of a single glass transition temperature (T_g) and a depression of the equilibrium melting temperature of the PEO component. The equilibrium melting temperature of PEO in the blends are obtained using Hoffman‐Weeks plots. The interaction energy density, β, is calculated from these data using the Nishi‐Wang equation. The results suggest that PEO and SMAI blends are thermodynamically miscible in the melt. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1–7, 2000     

Poly (ethylene oxide) (PEO) influence on mechanical,thermal, and degradation properties of PLA/PBSeT blends

Poly (lactic acid) (PLA) is an important biodegradable plastic with unique properties. However, its widespread application is hindered by its low miscibility and suboptimal degradation properties. To overcome these limitations, we investigated the mechanical, thermal, and degradation properties of PLA and poly (butylene sebacate-co-terephthalate) (PBSeT) blends in the presence of poly (ethylene oxide) (PEO). Specifically, this study aimed to identify the effects of PEO as a compatibilizer and hydrolysis accelerator in PLA/PBSeT blends. PLA (80%) and PBSeT (20%) were melt blended with various PEO contents (2–10 phr), and their mechanical, thermal, and hydrolytic properties were analyzed. All PEO-treated blends exhibited a higher elongation at break than that of the control sample, and the tensile strength was slightly reduced. In the PEO 10% sample, the elongation at break increased to 800% of that of the control sample. Differential scanning chromatography (DSC) analysis confirmed that when PEO was added to the PLA/PBSeT blends, the two glass transition temperatures (T_g) narrowed, resulting in improved miscibility of PLA and PBSeT. In addition, the hydrolytic degradation of the PLA/PBSeT/PEO blend accelerated as the PEO content increased. It was confirmed that PEO can act as a compatibilizer and hydrolysis-accelerating agent for PLA/PBSeT blends.     

Kraft lignin/poly(ethylene oxide) blends: Effect of lignin structure on miscibility and hydrogen bonding

Blends of poly(ethylene oxide) (PEO) with softwood kraft lignin (SKL) were prepared by thermal blending. The miscibility behavior and hydrogen bonding of the blends were investigated by differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. The experimental results indicate that PEO was miscible with SKL, as shown by the existence of a single glass‐transition temperature over the entire composition range by DSC. In addition, a negative polymer–polymer interaction energy density was calculated on the basis of the melting point depression of PEO. The formation of strong intermolecular hydrogen bonding was detected by FTIR analysis. A comparison of the results obtained for the SKL/PEO blend system with those previously observed for a hardwood kraft lignin/PEO system revealed the existence of stronger hydrogen bonding within the SKL/PEO blends but weaker overall intermolecular interactions between components; this suggested that more than just hydrogen bonding was involved in the determination of the blend behavior in the kraft lignin/PEO blends. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1437–1444, 2005     

Poly(hydroxyether sulfone) and its blends with poly(ethylene oxide): miscibility, phase behavior and hydrogen bonding interactions

Poly(hydroxyether sulfone) (PHES) was synthesized through polycondensation of bisphenol S with epichlorohydrin. It was characterized by Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy and differential scanning calorimetry (DSC). The miscibility in the blends of PHES with poly(ethylene oxide) (PEO) was established on the basis of the thermal analysis results. DSC showed that the PHES/PEO blends prepared by casting from N,N-dimethylformamide (DMF) possessed single, composition-dependent glass transition temperatures (T_gs), indicating that the blends are miscible in amorphous state. At elevated temperatures, the PHES/PEO blends underwent phase separation. The phase behavior was investigated by optical microscope and the cloud point curve was determined. A typical lower critical solution temperature behavior was observed in the moderate temperature range for this blend system. FTIR studies indicate that there are the competitive hydrogen bonding interactions upon adding PEO to the system, which was involved with the intramolecular and intermolecular hydrogen bonding interactions, i.e. -OH?OS, -OH?-OH and -OH versus ether oxygen atoms of PEO between PHES and PEO. In terms of the infrared spectroscopic investigation, it is judged that from weak to strong the strength of the hydrogen bonding interactions is in the following order: -OH?OS, -OH?-OH and -OH versus ether oxygen atoms of PEO.     

Some properties of organosoluble poly(2,5-didodecyloxy-p-phenylenevinylene) and its blends with poly(oxyethylene)

An organosoluble precursor of poly(2,5-didodecyloxy-p-phenylenevinylene) (PDDOPV) with high molecular weight was synthesized via the chlorine precursor route and characterized by IR and UV-Vis spectra, GPC, DSC, and elemental analysis. Factors effecting the thermal elimination reaction were studied. The solubility, absorption spectra and photoluminescence spectra of PDDOPV were also investigated. The conductivity of PDDOPV doped with different dopants (I₂, Br₂, FeCl₃ and H₂SO₄) and the I₂-doped conductivity of PDDOPV/PEO (polyoxyethylene) blends and PDDOPV/PEO/LiClO₄ blends were compared. The results showed that a synergistic mixed conductivity existed in the I₂-doped PDDOPV/PEO/LiClO₄ blend.     

Compatibility studies of sulfonated poly(ether ether ketone)–poly(ether imide)–polycarbonate ternary blends

Binary blends of the sulfonated poly(ether ether ketone) (SPEEK)–poly(ether imide) (PEI) and SPEEK–polycarbonate (PC), and ternary blends of the SPEEK–PEI–PC, were investigated by differential scanning calorimetry. SPEEK was obtained by sulfonation of poly(ether ether ketone) using 95% sulfuric acid. From the thermal analysis of the SPEEK–PEI blends, single glass transition temperature (T_g) was observed at all the blend composition. For the SPEEK–PC blends, double T_gs were observed. From the results of thermal analysis, it is suggested that the SPEEK–PEI blends are miscible and the SPEEK–PC blends are immiscible. Polymer–polymer interaction parameter (χ₁₂) of the SPEEK–PEI blends was calculated from the modified Lu and Weiss equation, and found to range from −0.011 to −0.825 with the blend composition. For the SPEEK–PC blends, the χ₁₂ values were calculated from the modified Flory–Huggins equation, and found to range from 0.191 to 0.272 with the blend composition. For the SPEEK–PEI–PC ternary blends, phase separation regions that showed two T_gs were found to be consistent with the spinodal curves calculated from the χ₁₂ values of the three binary blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2488–2494, 2000     

High molecular weight poly( -lactide) and poly(ethylene oxide) blends: thermal characterization and physical properties

The miscibility of high molecular weight poly( -lactide) PLLA with high molecular weight poly(ethylene oxide) PEO was studied by differential scanning calorimetry. All blends containing up to 50 weight% PEO showed single glass transition temperatures. The PLLA and PEO melting temperatures were found to decrease on blending, the equilibrium melting points of PLLA in these blends decreased with increasing PEO fractions. These results suggest the miscibility of PLLA and PEO in the amorphous phase. Mechanical properties of blends with up to 20 weight% PEO were also studied. Changes in mechanical properties were small in blends with less than 10 weight% PEO. At higher PEO concentrations the materials became very flexible, an elongation at break of more than 500% was observed for a blend with 20 weight% PEO. Hydrolytic degradation up to 30 days of the blends showed only a small variation in tensile strength at PEO concentrations less than 15 weight%. As a result of the increased hydrophilicity, however, the blends swelled. Mass loss upon degradation was attributed to partial dissolution of the PEO fraction and to an increased rate of degradation of the PLLA fraction. Significant differences in degradation behaviour between PLLA/PEO blends and (PLLA/PEO/PLLA) triblock-copolymers were observed.     

Thermal stability and Kinetic Study of rigid and plasticized Poly(vinyl chloride)/Poly(methylmethacrylate) blends

The thermal stability and kinetic parameters for degradation of rigid and plasticized poly(vinyl chloride)/poly (methylmethacrylate) blends have been investigated by using nonisothermal thermogravimetry in a flowing atmosphere of air. For that purpose, blends of variable composition from 0 to 100 wt% were prepared in the presence (15, 30, and 50 wt%) and in the absence of di‐(‐2‐ethyl hexyl) phthalate as plasticizer. Measurements were carried out in the temperature range of 30–550°C and at various heating rates (5, 10, 20, and 40°C/min). The kinetic parameters (E_a and A) were determined by applying the integral Kissinger method. Results indicate that these parameters and the thermal stability of the blends are dependent on the blend composition and the amount of plasticizer present. J. VINYL ADDIT. TECHNOL., 21:102–110, 2015. © 2014 Society of Plastics Engineers     

Miscibility and crystallization in crystalline/crystalline blends of poly(butylene succinate)/poly(ethylene oxide)

Miscibility and crystallization behavior have been investigated in blends of poly(butylene succinate) (PBSU) and poly(ethylene oxide) (PEO), both semicrystalline polymers, by differential scanning calorimetry and optical microscopy. Experimental results indicate that PBSU is miscible with PEO as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer-polymer interaction parameter, obtained from the melting depression of the high-T_m component PBSU using the Flory-Huggins equation, is composition dependent, and its value is always negative. This indicates that PBSU/PEO blends are thermodynamically miscible in the melt. The morphological study of the isothermal crystallization at 95 °C (where only PBSU crystallized) showed the similar crystallization behavior as in amorphous/crystalline blends. Much more attention has been paid to the crystallization and morphology of the low-T_m component PEO, which was studied through both one-step and two-step crystallization. It was found that the crystallization of PEO was affected clearly by the presence of the crystals of PBSU formed through different crystallization processes. The two components crystallized sequentially not simultaneously when the blends were quenched from the melt directly to 50 °C (one-step crystallization), and the PEO spherulites crystallized within the matrix of the crystals of the preexisted PBSU phase. Crystallization at 95 °C followed by quenching to 50 °C (two-step crystallization) also showed the similar crystallization behavior as in one-step crystallization. However, the radial growth rate of the PEO spherulites was reduced significantly in two-step crystallization than in one-step crystallization.     

Morphological characterization of γ-LiAlO2-filled composite polymer electrolytes containing LiPF6

Morphological properties of composite polymer electrolytes based on blends of polyethylene oxide (PEO) and a perfluorinated polyphosphazene (PPz) containing LiPF₆ as lithium salt and a finely divided ceramic filler, γ-LiAlO₂, were studied by using polarizing optical microscopy and differential scanning calorimetry (DSC). A parallel study was performed on propylene carbonate plasticized composite polymer electrolytes. Results indicate that both the morphology and the thermal properties depend upon the composition of the polymer host, a result not observed in composite polymer electrolytes having the same polymer composition containing LiCF₃SO₃ as lithium salt. The incorporation of the ceramic filler at the lower concentration tested (10% by wt) has practically no effect on the thermal behavior of the samples; whereas, differences were clearly distinguished at a concentration of ceramic material of 20 wt %. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1023–1030, 1999     

Crystal structure of the poly(ethylene oxide)–p-nitrophenol molecular complex

A crystalline complex of poly(ethylene oxide) (PEO) and p-nitrophenol (PNP) was studied by differential scanning calorimetry, X-ray diffraction, and FTIR spectroscopy, The phase diagram of this system is characterized by a peritectic reaction, and reveals the formation of a new crystal form different from those of PEO, and PNP. The triclinic unit cell of the complex was determined from the X-ray diffraction patterns of differently oriented samples obtained by mechanical deformations or spherulitic crystallizations. Finally, the molecular packing and the conformation adopted by the PEO chains were determined by FTIR spectroscopy. Polarization measurements have shown that the aromatic rings are very nearly normal to the c parameter (chain axis) and that the 1–4 axes of PNP molecules are parallel to the a^* reciprocal parameter (spherulitic growth direction). Finally, a new (t₂ gt₂ gt₃) conformation is proposed for the PEO chains on the basis of a normal mode analysis and the calculation of the intramolecular energy.     

Nanoheterogeneities in PEO/PMMA blends: A modulated differential scanning calorimetry approach

Modulated differential scanning calorimetry has been carried out on melt‐mixed blends of poly(ethylene oxide)/atactic‐poly(methyl methacrylate) (PEO/PMMA). Two PEO molecular weights have been used to prepare blends in the concentration range 10 to 80 wt % of PEO. Two glass transitions temperatures were observed for the fully amorphous blends, in the 10 to 30 wt % PEO range, using the differential of heat capacity with respect to temperature [dC_p/dT] signal. The semicrystalline blends, 40, 60, and 80 wt % PEO, exhibited melting of PEO crystallites and the PEO‐rich phase glass transition at −30 to −50°C. A second glass transition around 30°C was detected for the 40 wt % PEO blend when a cooling run was carried out, because PEO crystallization was avoided under these conditions. Therefore, heterogeneous amorphous phases were observed not only for fully amorphous blends, but also for semicrystalline ones. Further analysis of the dC_p/dT signal, obtained from the MTDSC experiments by fitting with Gaussian curves, showed that there is an interphase that varies in amount between 10 to 50 wt %. Correlation of the MTDSC observations with NMR spectroscopy and SAXS/SANS literature results are discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2034–2043, 2000     

Studies on the effect of laser radiation on the thermal stability of stabilized poly(vinyl chloride)

Nonisothermal studies were carried out using thermogravimetry (TG) and differential thermogravimetry (DTG) to obtain the activation energy of the decomposition for poly(vinyl chloride) (PVC), stabilized by ethyl, N‐phenylmaleimide, and 4‐carboxylate (ENPMC). Thermal gravitational analysis (TGA) indicated that the ENPMC–PVC samples decompose in two main breakdown stages. The effect of the addition of a stabilizer (ENPMC), with different concentrations, to PVC was studied. The results indicate that the addition of ENPMC with 0.01 g/1 g PVC enhances the thermal stability of pure PVC. Samples from 0.01 g ENPMC/1 g PVC were exposed to infrared laser radiation with energy fluency at levels between 0.95 and 8.53 J/cm². The results of the thermal experiments indicate that the onset temperature of decomposition T₀ and thermal activation energy of decomposition E_a are affected by the laser energy fluency owing to the simultaneous processes of degradation and crosslinking. The variation of transition temperatures with either the stabilizer concentration or the laser energy fluence was determined using differential thermal analysis (DTA). The results indicate that the irradiation with a laser to 7.11 J/cm² decreases the melting temperature of the pure PVC and this is most suitable for applications requiring the molding of this polymer at lower temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2249–2255, 2003     

Miscibility of C60-end-capped poly(ethylene oxide) with poly(vinyl chloride)

The miscibility of blends of single [60]fullerene (C₆₀)-end-capped poly(ethylene oxide) (FPEO) or double C₆₀-end-capped poly(ethylene oxide) (FPEOF) with poly(vinyl chloride) (PVC) has been studied. Similar to poly(ethylene oxide) (PEO), both FPEO and FPEOF are also miscible with PVC over the entire composition range. X-ray photoelectron spectroscopy showed the development of a new low-binding-energy Cl2p doublet and a new high-binding-energy O1s peak in FPEO/PVC blends. The results show that the miscibility between FPEO and PVC arises from hydrogen bonding interaction between the α-hydrogen of PVC and the ether oxygen of FPEO. From the melting point depression of PEO, FPEO or FPEOF in the blends, the Flory-Huggins interaction parameters were found to be −0.169, −0.142, −0.093 for PVC/PEO, PVC/FPEO and PVC/FPEOF, respectively, demonstrating that all the three blend systems are miscible in the melt. However, the incorporation of C₆₀ slightly impairs the interaction between PEO and PVC.     

Synthesis of high molecular weight polyoxyethylene with a quaternary catalyst and study of its conductive blends with poly(2‐vinyl pyridine)

High molecular weight polyoxyethylene (PEO) was synthesized by using a quaternary catalyst composed of triisobutyl aluminum, phosphoric acid, water, and N,N‐dimethylaniline (DMA). Optimum synthesis conditions and some properties of the product were studied. This catalyst showed high activity and the molecular weight of the polyoxyethylene obtained can approach one million. The activity of polymerization mainly depends upon the composition of catalyst. The optimum composition is as follows: i‐Bu₃Al:H₃PO₄:H₂O:DMA = 1 : 0.17 : 0.17 : 0.10–0.15 (molar ratio).The active centers of the catalyst was thus proposed. The high molecular weight PEO synthesized by this catalyst was blended with poly(2‐vinyl pyridine) (PVP) and then doped with LiClO₄ and TCNQ to obtain a conductive elastomeric material. Ionic, electronic, and mixed (ionic–electronic) conductivities of blends were investigated. At a Li/EO molar ratio of 0.1 and a TCNQ/VP molar ratio of 0.5, the mixed conductivity of the blend of PEO/PVP/LiCIO₄/TCNQ is higher than the sum of ionic conductivity of PEO/PVP/LiCIO₄ and electronic conductivity of PEO/PVP/TCNQ, when the weight ratio of PEO to PVP is 6/4 or 5/5. It can reach 4 × 10^?6 S/cm at room temperature. Differential scanning calorimetry, thermal gravimetric analysis, and the appearance of the blend showed that both TCNQ and LiClO₄ can complex with PEO and PVP, thus enhancing the compatibility between PEO and PVP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Crystallization behavior of PEO in blends of poly(ethylene oxide)/poly(2‐vinyl pyridine)‐b‐(ethylene oxide) block copolymer

The crystallization behavior of two molecular weight poly(ethylene oxide)s (PEO) and their blends with the block copolymer poly(2‐vinyl pyridine)‐b‐poly(ethylene oxide) (P2VP‐b‐PEO) was investigated by polarized optical microscopy, thermogravimetric analysis, differential scanning calorimetry, and atomic force microscopy (AFM). A sharp decreasing of the spherulite growth rate was observed with the increasing of the copolymer content in the blend. The addition of P2VP‐b‐PEO to PEO increases the degradation temperature becoming the thermal stability of the blend very similar to that of the block copolymer P2VP‐b‐PEO. Glass transition temperatures, T_g, for PEO/P2VP‐b‐PEO blends were intermediate between those of the pure components and the value increased as the content of PEO homopolymer decreased in the blend. AFM images showed spherulites with lamellar crystal morphology for the homopolymer PEO. Lamellar crystal morphology with sheaf‐like lamellar arrangement was observed for 80 wt% PEO(200M) and a lamellar crystal morphology with grain aggregation was observed for 50 and 20 wt% blends. The isothermal crystallization kinetics of PEO was progressively retarded as the copolymer content in the blend increased, since the copolymer hinders the molecular mobility in the miscible amorphous phase. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers