13C‐NMR study on the structure of phenol‐urea‐formaldehyde resins prepared by methylolureas and phenol

Phenol‐urea‐formaldehyde (PUF) resins were synthesized by reacting mixture of methylolureas (MMU), phenol, and formaldehyde. The structure of PUF cocondensed resins at different stages of reaction were analyzed by liquid ¹³C nuclear magnetic resonance (NMR) spectroscopy. The liquid ¹³C‐NMR analysis indicated that methylolureas had the dominant content in MMU with the reaction between urea and formaldehyde under the alkaline condition. The PUF cocondensed resins had no free formaldehyde. methylolureas were well incorporated into the cocondensed resins by reacting with phenolic units to form cocondensed methylene bridges. The second formaldehyde influenced the further reaction and the structure of the PUF resins. The resins with the prepared method of PUFB possessed relatively high degree of polymerization and low proportion of unreacted methylol groups. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phenol–urea–formaldehyde resin co-polymer synthesis and its influence on Elaeis palm trunk plywood mechanical performance evaluated by 13C NMR and MALDI-TOF mass spectrometry

This study evaluated a new method of producing phenol–urea–formaldehyde (PUF) adhesives formulated differently under actual “in-situ” resin synthesis conditions. This was carried out by co-polymerizing urea formaldehyde (UF) resin with phenol–formaldehyde resin in the core layer of low molecular weight (LMW) phenol–formaldehyde (PF) resin treated Elaeis palm trunk veneers during the gluing process of Elaeis palm plywood. Matrix assisted laser desorption Ionization time of flight (MALDI-TOF) mass spectrometry (MS) illustrated and confirmed a series number of the phenol–urea co-condensates repeating unit in the prepared PUF resins which corroborated well with its mechanical properties (modulus of elasticity and modulus of rupture), bonding quality (dry test and weather boil proof or WBP test) and physical properties. A series of PF, UF and PUF resins oligomers forming repeating units up to 1833 Da were identified. Besides that, the solid state ¹³Carbon nuclear magnetic resonance (NMR) interpretation identified that the signal at 44–45 ppm and 54–55 ppm corresponding to methylene bridges were co-condensated in between phenol and urea in the PUF resin system. The ¹³C NMR investigation showed that the synthesis process of PUF resin contained no free formaldehyde elements. Furthermore, the proportion of urea and methylolureas in the mixture to synthesis PUF resin were sufficient and incorporated well into the formulation by reacting with LMWPF units to form co-condensed methylene bridges. This study showed a new and useful method to synthesize PUF resin during the gluing process of manufactured Elaeis palm plywood which can also enhance the performance of Elaeis palm plywood panels for structural instead of utility grade applications.     

Synthesis–structure–performance relationship of cocondensed phenol–urea–formaldehyde resins by MALDI‐ToF and 13C NMR

Matrix assisted laser desorption ionization time of flight (MALDI‐ToF) mass spectrometry has consistently confirmed on a number of PUF resins that phenol–urea cocondensates exist in phenol–urea–formaldehyde (PUF) resins. A noticeable proportion of methylene‐linked phenol to urea cocondensates were detected in all the PUF resins tried, alongside methylene bridges connecting phenol to phenol and urea to urea. The PUF, PF, and UF oligomers formed were identified. Variations of the PUF preparation procedure did always yield a certain proportion of the mixed phenol to urea cocondensates. Their relative proportion was determined and related the synthesis procedure used. Comparison of the MALDI‐ToF results with a ¹³C NMR investigation showed that in a real PUF resin in which phenol to urea cocondensates were identified the methylene bridge NMR signal at 44 ppm, characteristic of phenol to urea unsubstituted model compound cocondensates, does not appear at all. This confirmed that this peak cannot be taken as an indication of the existence of phenol and urea condensation under actual resin preparation conditions. The peak indicating cocondensation in PUF resins in which the phenolic nuclei and urea are substituted appears instead at 54.7–55.0 ppm. Thermomechanical analysis has again confirmed that the resin gel times greatly accelerates with increasing urea molar content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fast advancement and hardening acceleration of low condensation alkaline phenol‐formaldehyde resins by esters and copolymerized urea. II. Esters during resin reaction and effect of guanidine salts

Guanidine carbonate is shown to be an accelerator of phenol‐formaldehyde (PF) resins that while yielding slightly slower gel times than triacetin when added to a PF resin glue mix, is also capable of giving glue‐mix pot lives on the order of several days. Hence, this is long enough to be premixed with the resin long before use. Both triacetin and guanidine carbonate used as simple glue‐mix additives are shown to increase the ultimate strength of the resin bond, whatever the length of the curing time used for the purpose. This is shown by thermomechanical analysis and the application to wood particleboard. Triacetin is shown to be usable during PF resin preparation rather than just being added to the glue mix, yielding better resins capable of giving higher bond values without a great acceleration of the geling of the resin itself. The mechanisms involved in the acceleration of PF resins introduced by both compounds appears to be based on facilitating reactions of crosslinking involving carbonic acid ions present in the resin solution. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 249–259, 2000     

Copolymerization in UF/pMDI adhesives networks

Kinetic evidence in thermomechanical analysis experiments and carbon‐13 nuclear magnetic resonance spectroscopy (¹³C NMR) evidence indicates that the strength of a joint bonded with UF (urea–formaldehyde)/polymeric 4,4'‐diphenylmethane diisocyanate (pMDI) glue mixes is improved by coreaction of the methylol groups of UF resins with pMDI to form a certain number of methylene cross‐links. The formation of these methylene cross‐links is predominant, rather than formation of urethane bridges which still appear to form but which are in great minority. This reaction occurs in presence of water and under the predominantly acid hardening conditions, which is characteristic of aminoplastic resins (thus, in presence of a hardener). Coreaction occurs to a much lesser extent under alkaline conditions (hence, without UF resins hardeners). The predominant reaction is then different in UF/pMDI adhesive systems than that observed in phenol‐formaldehyde (PF)/pMDI adhesive systems. The same reaction observed for UF/pMDI system at higher temperatures has also been observed in PF/pMDI systems, but only at lower temperatures. The water introduced in the UF/pMDI mix by addition of the UF resin solution has been shown not to react with pMDI to an extent such as to contribute much, if at all, to the increase in strength of the hardened adhesive. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3681–3688, 2002     

胶合板用尿素改性酚醛树脂胶合性能的研究

制备了不同尿素用量的系列尿素改性酚醛（PUF）树脂体系（当尿素用量为苯酚质量的0、25%、43%、66%时分别记为PF、PUF-1、PUF-2、PUF-3）,并将其用于制备胶合板,研究树脂在胶合板加工过程中的变化。结果表明：PUF-3树脂与桉木和杨木的接触角为79.6°和81.1°,小于PF树脂的,PUF对桉木相容性比杨木优良,PF树脂则相反;对4种树脂进行DSC分析显示,PF、PUF-1、PUF-2、PUF-3固化速率最大温度分别为146.8、171.4、171.8和171.8℃;PUF-3和面粉共混体系的流变行为显示该共混体系110℃开始发生固化反应,（130±5）℃为较合适的热压温度;对热压前后PF和PUF-3进行热重分析,结果发现PUF的耐高温性能优于PF,热压后形成的结构耐热性也更好;4种树脂压制的胶合板性能达到E₀级,甲醛释放量均小于0.5mg/L,胶合强度分别为1.42、1.11、0.98和0.92MPa。     

Curing of low level melamine‐modified urea‐formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)

Effects of resin formulation, catalyst, and curing temperature were studied for particleboard binder‐type urea‐formaldehyde (UF) and 6 ～ 12% melamine‐modified urea‐melamine‐formaldehyde (UMF) resins using the dynamic mechanical analysis method at 125 ～ 160°C. In general, the UF and UMF resins gelled and, after a relatively long low modulus period, rapidly vitrified. The gel times shortened as the catalyst level and resin mix time increased. The cure slope of the vitrification stage decreased as the catalyst mix time increased, perhaps because of the deleterious effects of polymer advancements incurred before curing. For UMF resins, the higher extent of polymerization effected for UF base resin in resin synthesis increased the cure slope of vitrification. The cure times taken to reach the vitrification were longer for UMF resins than UF resins and increased with increased melamine levels. The thermal stability and rigidity of cured UMF resins were higher than those of UF resins and also higher for resins with higher melamine levels, to indicate the possibility of bonding particleboard with improved bond strength and lower formaldehyde emission. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 377–389, 2005     

Uron and uron–urea‐formaldehyde resins

The favored pH ranges for the formation of urons in urea‐formaldehyde (UF) resins preparation were determined, these being at pH's higher than 6 and lower than 4 at which the equilibrium urons ↔ N,N′‐dimethylol ureas are shifted in favor of the cyclic uron species. Shifting the pH slowly during the preparation from one favorable range to the other causes shift in the equilibrium and formation of a majority of methylol ureas species, whereas a rapid change in pH does not cause this to any great extent. UF resins in which uron constituted as much as 60% of the resin were prepared and the procedure to maximize the proportion of uron present at the end of the reaction is described. Uron was found to be present in these resins also as linked by methylene bridges to urea and other urons and also as methylol urons, the reactivity of the methylol group of this latter having been shown to be much lower than that of the same group in methylol ureas. Thermomechanical analysis (TMA) tests and tests on wood particleboard prepared with uron resins to which relatively small proportions of urea were added at the end of the reaction were capable of gelling and yielding bonds of considerable strength. Equally, mixing a uron‐rich resin with a low F/U molar ratio UF resin yielded resins of greater strength than a simple UF of corresponding molar ratio indicating that UF resins of lower formaldehyde emission with still acceptable strength could be prepared with these resins. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 277–289, 1999     

Co‐polymerization analysis of thermosetting resins using 1H‐15N‐13C triple resonance NMR spectroscopy

¹H‐¹⁵N‐¹³C correlation NMR spectroscopy techniques developed to identify and characterize co‐polymer fragments in melamine‐urea‐formaldehyde (MUF) and phenol‐urea‐formaldehyde (PUF) model systems have been applied to industrially prepared MUF, PUF, and phenol‐melamine‐formaldehyde (PMF) resins. The NMR data confirm that co‐polymers form in a commercially prepared MUF resin manufactured by Momentive Specialty Chemicals Pty. Ltd. Spectra from PUF model reactions were compared with those from a PUF resin and it was determined that PUF co‐polymers did not form in the resin prepared using typical temperature and pH. Finally, NMR spectroscopy was used to identify and characterize PMF co‐polymer bonds in a phenol‐melamine‐urea‐formaldehyde (PMUF) resin prepared using a procedure from Momentive Specialty Chemicals Pty. Ltd. With these NMR techniques in hand, it is now possible to relate co‐polymer structures to properties of commercial thermosets. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. IV

Typical particleboard wood‐adhesive urea–formaldehyde (UF) resins, synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.80, 2.10, and 2.40 and the second urea added to an overall F/U ratio of 1.15, in weak alkaline pH, were allowed to stand at room temperature over a period of 50 days. ¹³C‐NMR of time samples taken over the storage period showed gradual migration of hydroxymethyl groups from the polymeric first‐urea components to the monomeric second‐urea components and also an advancing degree of polymerization of resins by forming methylene and methylene ether groups involving the second urea. These phenomena that varied with the F/U₁ mol ratios used in the resin syntheses due to the varying polymer branching structures resulted in the first step of resin synthesis. Varying viscosity decreases and increases of the resins also occurred. Due to these chemical and physical changes, the particleboards that bonded with the sampled resins showed varying bond strength and formaldehyde‐emission values, indicating process optimizations possible to improve bonding and formaldehyde‐emission performances. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1155–1169, 2001     

Properties of phenol‐formaldehyde resins prepared from phenol‐liquefied lignin

In this study, alkaline lignin (AL), dealkaline lignin (DAL), and lignin sulfonate (SL) were liquefied in phenol with sulfuric acid (H₂SO₄) or hydrochloric acid (HCl) as the catalyst. The phenol‐liquefied lignins were used as raw materials to prepare resol‐type phenol‐formaldehyde resins (PF) by reacting with formalin under alkaline conditions. The results show that phenol‐liquefied lignin‐based PF resins had shorter gel time at 135°C and had lower exothermic peak temperature during DSC heat‐scanning than that of normal PF resin. The thermo‐degradation of cured phenol‐liquefied lignin‐based PF resins was divided into four temperature regions, similar to the normal PF resin. When phenol‐liquefied lignin‐based PF resins were used for manufacturing plywood, most of them had the dry, warm water soaked, and repetitive boiling water soaked bonding strength fitting in the request of CNS 1349 standard for Type 1 plywood. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Variation of MUF and PMUF resins mass fractions during preparation

The variation of molecular mass distribution with the progress of the reaction was studied for the following: (i) sequential‐type melamine–urea–formaldehyde (MUF) resin formulations in which the sequence of addition of chemicals follows well‐defined species reactivity principles; (ii) a nonsequential MUF formulation in which simultaneous melamine and urea competition for formaldehyde yields a MF resin cocondensed with small amounts of urea. This resin became soaked with reacted and unreacted monomeric urea species. (iii) A PMUF resin, namely a MUF resin with a small proportion of phenol (7.8% by weight on melamine and urea) cocondensed with the main MUF fraction. All the formulations used were industrial resins formulations in current use. Development and variation of molecular mass fractions, from which performance and other useful resin parameters depend, have been found to depend on the type of resin formulation used for these type of aminoplastic resins. The two very different MUF resin formulations yielded different variations in molecular mass fractions during the progress of the reaction and during the so‐called ambient temperature “maturing” of the resin. The PMUF resin also showed both similar and different fractions present during manufacturing and during short term ageing at ambient temperature. While similarities in recurrent fractions and in trends are common to all the three different formulations, differences between them are also clearly observed. A major proportion of the reaction of some of the aminoplastic resins examined also occurs on ageing (i.e.“maturing” of the resin at ambient temperature), this appearing to be an essential phase of the resin preparation process. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4842–4855, 2006     

13C NMR study on the structure of ZnO-catalyzed phenol–urea–formaldehyde resin during its synthesis process

The structure of ZnO-catalyzed phenol–urea–formaldehyde (PUF) resin at different synthesis stages was analyzed by liquid ¹³C nuclear magnetic resonance spectroscopy. The results showed that the general structure of ZnO-catalyzed PUF resin was almost the same as the control PUF resin. Addition reaction between phenol and formaldehyde mainly occurred at the first stage. Total methylol groups amount between phenols of the control resin was a little lower than that of the ZnO-catalyzed PUF resin. Co-condensation and self-condensation reaction occurred at the second stage. The preparation method of ZnO-catalyzed PUF resin favored the co-condensation reaction between phenol methylol groups and urea units, while self-condensation reaction dominated the control resin at the second stage. Formaldehyde completely reacted for both the control and ZnO-catalyzed PUF final resin. The total amount of methylol and methylene groups between urea units and phenols, respectively, was almost the same for the two final resins. The total quantity of methylol groups between phenols represented a continuing downward trend from the first stage to the final stage, and the amount of methylol group (p-Ph–CH₂OH) of ZnO-catalyzed PUF resin was 30% more than that of the control resin. Total co-condensed methylene groups amount of ZnO-catalyzed PUF resin was greater than that of the control resin, which indicated that ZnO could make the urea units well incorporated into the co-condensed PUF resin.     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. V

The effects of posttreatments of particleboard adhesive‐type urea–formaldehyde resins were studied. The resins were synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.40, 1.60, 1.80, 2.10, and 2.40 and then the second urea was added to give a final formaldehyde/urea ratio of 1.15 in alkaline pH. The resins were posttreated at 60°C for up to 13.5 h and the 2.5‐h heat‐treated resin samples were stored at room temperature for up to 27 days. Resins sampled during the posttreatments were examined by ¹³C‐NMR and evaluated by bonding particleboards. In the posttreatments, hydroxymethyl groups on the polymeric resin components dissociated to formaldehyde and reacted with the second urea, and methylene and methylene–ether groups were formed from reactions involving the second urea. Methylene–diurea and urea groups bonded to UF polymers were identified. As a result, the viscosity of the resins initially decreased but later increased along with the cloudiness of the resins. Bond‐strength and formaldehyde‐emission values of particleboard varied with posttreatment variables as well as with the F/U₁ mol ratios used in the resin syntheses. The results would be useful in optimizing resin synthesis and handling parameters. Various reaction mechanisms were considered. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1896–1917, 2003     

Effect of resin type and content on properties of composite particleboard made of a mixture of wood and rice husk

This study investigated the effect of resin type and content on the dimensional stability and mechanical properties of single-layer composite particleboards made of a mixture of wood particles (70 wt%) and rice husk particles (30 wt%). Two types of resin, urea–formaldehyde (UF) resin and phenol–formaldehyde (PF) resin, were used in the experiments at three different contents which were 8, 10, or 12 wt%. The dimensional stability of the samples was significantly improved by increasing the resin content. When the contents of the UF and PF resins increased from 8 to 12 wt%, the WA values of the samples decreased to18% and 33%, respectively. Similar results were also observed for the TS values. The UF resin bonded samples swelled two times more than the PF resin bonded particleboard. The mechanical properties of the PF resin bonded samples were better than the UF resin bonded samples. When the contents of the UF and PF resins increased from 8% to 12 wt%, the internal bond strength values of the samples increased to 21% and 41%, respectively. The bending strength and modulus of elasticity of the samples were not significantly increased by increasing contents of the UF and PF resins, except for the 12 wt% content.     

Urea–formaldehyde–propionaldehyde physical gelation resins for improved swelling in water

Urea–formaldehyde (UF) resins' water tolerance and swelling thickness of interior‐grade wood panels bonded with UF resins were improved markedly by introducing small amounts of UFPropanal (UFP) polycondensates into the UF resin. ¹³C NMR of urea–propanal (UP) resins showed that urea and propanal do react up to the formation of dimers. The water repellancy imparted by insertion in the resin of the alkyl chain of propanal limits the proportion of propanal that can be used. Gel permeation chromatography showed that this appears to be so because UP resins and UFP resins exist as an equilibrium between two separate intermingling phases, namely one in solution and the second in a state of physical gelation. This latter is different from the state of physical gelation observed on ageing or advancement of formaldehyde‐only based polycondensation resins. This physical gelation is brought on by the insertion in the resin of the water repellant chain of the propanal reacted with urea and constitutes a new state of physical gelation of polycondensates other than what was already reported in the literature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5131–5136, 2006     

Evaluation of melamine‐modified urea‐formaldehyde resins as particleboard binders

Particleboards bonded with 6 and 12% melamine‐modified urea‐formaldehyde (UMF) resins were manufactured using two different press temperatures and press times and the mechanical properties, water resistance, and formaldehyde emission (FE) values of boards were measured in comparison to a typical urea‐formaldehyde (UF) resin as control. The formaldehyde/(urea + melamine) (F/(U + M)) mole ratio of UMF resins and F/U mole ratio of UF resins were 1.05, 1.15, and 1.25 that encompass the current industrial values near 1.15. UMF resins exhibited better physical properties, higher water resistance, and lower FE values of boards than UF resin control for all F/(U + M) mole ratios tested. Therefore, addition of melamine at these levels can provide lower FE and maintain the physical properties of boards. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A study on composites from phenol‐formaldehyde‐casein resin

A modified phenol‐formaldehyde (PF) resin was synthesized under alkaline condition in varying proportion of casein up to 20% (w/w) of phenol. All the prepared resins were characterized by free phenol content, free formaldehyde content, viscosity measurements, number average molecular weight determination by conductometry and Infrared Spectroscopy (IR). Their curing kinetics was studied isothermally and by differential scanning calorimetry (DSC) on dynamic runs. The resin samples were cured using concentrated hydrochloric acid and hexamine individually. Cured resins were characterized by IR and Thermogravimetry (TGA). Glass fabric reinforced composites (GFRC) were fabricated by maintaining 40 : 60 proportion of resin to reinforcement material. The laminates thus formed were characterized for their mechanical properties and chemical resistance. Enhancements in thermal stability of the resin as well as toughness of composite with increase in casein content were observed for the resins studied. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The reaction in water of UF resins with isocyanates at short curing times: A 13C NMR investigation

CP MAS ¹³C NMR spectra of hardened resins have shown that urethane bridges derived from the reaction of the isocyanate group with the hydroxymethyl group of urea do form even at fast curing times comparable to what was used in the wood panels industry, in lower proportions than what was shown earlier. Polyureas and biurets obtained from the reaction of isocyanate with water are the predominant crosslinking reactions of pMDI alone and in UF/pMDI resin systems under fast curing conditions. Residual, unreacted isocyanate groups in the hardened network are consistently observed. Their proportion markedly decreases when the original proportion of urea–formaldehyde (UF) resin is high and that of pMDI is low. Under these fast curing conditions, the UF resin appears to self‐condense through an unusually high proportion of methylene ether links rather than methylene bridges alone. A marked proportion of residual, unreacted hydroxymethyl groups is also noticeable, initially, in the UF self‐condensation network. Direct NMR tests on thin hardboard bonded under fast pressing conditions with different proportions of UF/pMDI confirmed that crosslinking due to polyureas and biurets formation are predominant in the crosslinking of pMDI when alone and in UF/pMDI resin systems. They confirmed that residual, unreacted isocyanate groups are present in the finished panel. Their proportion is higher when the proportion of pMDI in the system is high. The presence or absence of urethanes could not be confirmed directly on the panels as the relevant peaks are masked by the wood carbohydrates signals of wood cellulose and hemicelluloses. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1624–1632, 2006     

Effects of urea and curing catalysts added to the strand board core‐layer binder phenol–formaldehyde resin

Effects of adding urea to the strand board core‐layer phenol–formaldehyde (PF) resin were investigated in conjunction with cure‐accelerating catalysts. Ten percent urea based on the liquid resin weight was added at the beginning, at three different middle stages of polymerization, and at the end of PF resin synthesis. No significant cocondensation between the urea and PF resin components occurred as identified by ¹³C NMR analyses, which corroborated well with the curing and strand board bonding performance test results. The various urea addition methods resulted in resins that slightly differ in the various tests due to the urea's temporary holding capacity of formaldehyde. The preferred method of urea addition was found to do it in the later part of PF resin synthesis for convenience, consistency, and slightly better overall performance. Some cure‐accelerating catalysts were shown to reduce the thickness swelling of strand boards. This study showed the usefulness of adding some urea to strand board core‐layer binder PF resins of replacing higher cost phenolic components with lower cost urea. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007