Blends of poly(vinyl chloride) (PVC)/natural rubber‐g‐(styrene‐co‐methyl methacrylate) for improved impact resistance of PVC

To improve the mechanical properties of poly(vinyl chloride) (PVC), the possibility of combining PVC with elastomers was considered. Modification of natural rubber (NR) by graft copolymerization with methyl methacrylate (MMA) and styrene (St) was carried out by emulsion polymerization by using redox initiator to provide an impact modifier for PVC. The impact resistance, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM) of St and MMA grafted NR [NR‐g‐(St‐co‐MMA)]/PVC (graft copolymer product contents of 5, 10, and 15%) blends were investigated as a function of the amount of graft copolymer product. It was found that the impact strength of blends was increased with an increase of the graft copolymer product content. DMA studies showed that NR‐g‐(St‐co‐MMA) has partial compatibility with PVC. SEM confirmed a shift from brittle failure to ductility with an increase graft copolymer content in the blends. The mechanical properties showed that NR‐g‐(St‐co‐MMA) interacts well with PVC and can also be used as an impact modifier for PVC. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1666–1672, 2004     

Studies on mechanical and morphological behavior of hybrid nanoclay‐reinforced EPDM‐g‐TMEVS/PS blends

A new copolymer of tris(2‐methoxyethoxy) vinylsilane (TMEVS)‐grafted ethylene–propylene–diene elastomer (EPDM‐g‐TMEVS) has been developed by grafting of TMEVS onto EPDM by using dicumylperoxide (DCP) initiator. The linear polystyrene blends (EPDM‐g‐TMEVS/PS) based on EPDM‐g‐TMEVS have been synthesized with varying weight percentages of polystyrene in a twin‐screw extruder. In a similar manner, the dynamically vulcanized and nanoclay‐reinforced polystyrene blends have also been developed using DCP and organically modified montmorillonite clay separately by means of a twin‐screw extruder. The grafting of TMEVS onto EPDM at allylic position present in the third monomer of EPDM has been confirmed by Fourier Transform infrared spectroscopy. The effect of silane‐grafted EPDM and concentration of nanoclay on mechanical properties of polystyrene blends has been studied as per ASTM standards. The morphological behavior of these blends has been investigated using scanning electron microscope. It was observed that the incorporation of silane‐grafted EPDM enhanced the impact strength and the percentage elongation of linear‐ and dynamically vulcanized blends. However, the values of tensile strength, flexural strength, flexural modulus, and hardness of the blends were found to be decreasing with the increase of silane‐grafted EPDM. In the case of nanoclay‐reinforced polystyrene blends, the values of impact strength, tensile strength, flexural strength, flexural modulus, and hardness were increased with an increase in the concentration of nanoclay. XRD studies have been carried out to confirm the formation of nanoclay‐reinforced EPDM‐g‐TMEVS/PS blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Properties and morphologies of PVC/nylon terpolymer blends

A new kind of blends of polyvinyl chloride (PVC)/nylon terpolymer was reported in this article. Two compatibilizers were used in this study: one is a terpolymer of ethylene–n‐butyl acrylate–monoxide (EnBACO); the other is terpolymer of EnBACO grafted with maleic anhydride (EnBACO‐g‐MAH). The observation of scanning electron microscope (SEM) reveals that the PVC/nylon terpolymer blends have a two‐phase structure; and the nylon terpolymer phase is the continuous phase, and PVC domains in the PVC/nylon terpolymer/EnBACO‐g‐MAH blends have fine dispersion over a broad range of the PVC/nylon terpolymer ratio. EnBACO‐g‐MAH is more compatible with the nylon terpolymer than EnBACO. EnBACO and EnBACO‐g‐MAH have different effects on the glass transition temperatures of the PVC phase and nylon terpolymer phase in the blends. The notched Izod impact strength, tensile strength, elongation at break, Vicat softening temperature (VST), and melt flow index (MFI) critically depend on PVC/nylon terpolymer ratio, the kinds and concentration of the compatibilizers. The PVC/nylon terpolymer/EnBACO‐g‐MAH blends display a good combination of high toughness, high flowability, and high VST under low load. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2823–2832, 2001     

Novel multimonomer‐grafted polypropylene preparation and application in polypropylene/poly(vinyl chloride) blends

A novel grafted polymer was prepared in one step through free‐radical melt grafting in a single‐screw extruder. It was shown that the addition of styrene (St) to the melt‐grafting system as a comonomer could significantly enhance the grafting degree of methyl methacrylate (MMA) onto polypropylene (PP) and reduce the degradation of the PP matrix by means of Fourier transform infrared and melt flow rate testing, respectively. Then, the potential of using multimonomer‐grafted PP, which was designated PP‐g‐(St‐co‐MMA), as the compatibilizer in PP/poly(vinyl chloride) (PVC) blends was also examined. In comparison with PP/PVC blends, the average size of the dispersed phase was greatly reduced in grafted polypropylene (gPP)/PVC blends because of the addition of the PP‐g‐(St‐co‐MMA) graft copolymer. The tensile strength of the gPP/PVC blends increased significantly, and the impact strength was unchanged from that of the pure PP/PVC blends. The results of differential scanning calorimetry and scanning electron microscopy suggested that the compatibility of the PP/PVC blends was improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of a methyl methacrylate/ethyl acrylate/acrylic acid terpolymer to improve the homogeneity of ethylene–propylene–diene monomer rubber/poly(vinyl chloride) blends

The emulsion terpolymerization of methyl methacrylate (MMA), ethyl acrylate (EA), and acrylic acid (AA) was carried out under a nitrogen atmosphere at 70°C. The final terpolymer conversion was determined gravimetrically. The synthesized MMA–EA–AA terpolymer was characterized with ¹H‐NMR spectroscopy, thermal analysis, and gel permeation chromatography. Glass‐transition temperatures of the MMA–EA–AA terpolymer were determined with a differential scanning calorimeter. Ethylene–propylene–diene monomer rubber (EPDM)/poly(vinyl chloride) (PVC) blends were prepared with different blend ratios (10/90, 20/80, 30/70, 40/60, and 50/50) in the presence and absence of MMA–EA–AA as a compatibilizer. The morphology of those blends was examined with the aid of a scanning electron microscope. The scanning electron micrographs in the presence of the MMA–EA–AA terpolymer illustrated the disappearance of the macroscale phase separation of EPDM/PVC blends as a result of the incorporation of MMA–EA–AA into that blend, indicating an improvement of the homogeneity. The mechanical properties of the EPDM/PVC blend films and the dielectric properties of the melt blends were investigated. The swelling behavior of the cured blends in the brake fluid was also discussed. The results illustrated that the mechanical properties, the weight swelling values, and the dielectric constant values showed linear behavior versus the blend ratios after the incorporation of the terpolymer. However, those values showed deviations from linearity in the absence of the terpolymer. That, in turn, ensured the results obtained with the scanning electron microscope. The results reveal that the MMA–EA–AA terpolymer prepared can be used successfully to improve the homogeneity of EPDM/PVC blends used in hose and oil seal applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of core‐shell morphology evolution on the rheology,crystallization, and mechanical properties of PA6/EPDM‐g‐MA/HDPE ternary blend

In this article, polyamide 6 (PA6), maleic anhydride grafted ethylene‐propylene‐diene monomer (EPDM‐g‐MA), high‐density polyethylene (HDPE) were simultaneously added into an internal mixer to melt‐mixing for different periods. The relationship between morphology and rheological behaviors, crystallization, mechanical properties of PA6/EPDM‐g‐MA/HDPE blends were studied. The phase morphology observation revealed that PA6/EPDM‐g‐MA/HDPE (70/15/15 wt %) blend is constituted from PA6 matrix in which is dispersed core‐shell droplets of HDPE core encapsulated by EPDM‐g‐MA phase and indicated that the mixing time played a crucial role on the evolution of the core‐shell morphology. Rheological measurement manifested that the complex viscosity and storage modulus of ternary blends were notable higher than the pure polymer blends and binary blends which ascribed different phase morphology. Moreover, the maximum notched impact strength of PA6/EPDM‐g‐MA/HDPE blend was 80.7 KJ/m² and this value was 10–11 times higher than that of pure PA6. Particularly, differential scanning calorimetry results indicated that the bulk crystallization temperature of HDPE (114.6°C) was partly weakened and a new crystallization peak appeared at a lower temperature of around 102.2°C as a result of co‐crystal of HDPE and EPDM‐g‐MA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Investigation of crystallization behavior in dynamically vulcanized EPDM–nylon copolymer blends

A thermoplastic vulcanizate (TPV) of a ethylene–propylene–diene terpolymer (EPDM) and nylon copolymer (PA) was prepared by dynamic vulcanization. Maleic anhydride (MAH)–grafted EPDM (EPDM–g–MAH), MAH‐grafted EPR (EPR–g–MAH), and chlorinated polyethylene (CPE) were used as compatibilizers. The effect of dynamic vulcanization and compatibilizer on the crystallization behavior of PA was investigated. Differential scanning calorimeter measurement results showed no pronounced shift in the crystallization temperature for PA in EPDM–PA TPV compared to that for PA in the neat state, whereas the crystallization temperature increased after adding compatibilizer. The decrease in the crystallinity of TPVs was a result of the crystallization occurring in confined spaces between rubber particles. The equilibrium melting temperature (Tm⁰) of the PA copolymer was measured and was determined to be 157°C. The isothermal crystallization kinetics of PA in the neat and TPV states also was investigated. The crystallization rate was highest in the compatibilized TPV and lowest in the neat PA, whereas it was intermediate in the uncompatibilized TPV unvulcanized blends. Compared with unvulcanized EPDM–PA blends, the dynamic vulcanization process seemed to cause an obvious increase in the crystallization rate of the PA copolymer, especially when a suitable compatibilizer was used. This occurred because the dynamic vulcanization introduced fine crosslinked rubber particles that could act as heterogeneous nucleating centers. In addition, the use of a suitable compatibilizer permitted the formation of finely dispersed vulcanized rubber particles and therefore increased the density of the nucleating centers. The complex morphology of the blends was investigated by atomic force microscopy to evaluate the effect of compatibilizer on the size of the dispersed rubber particles. Compared with the morphology of TPVs with the same dosage of EPDM–g–MAH compatibilizer, the morphology of TPVs using EPR–g–MAH as compatibilizer showed much smaller dispersed rubber particles, which may have contributed to the higher crystallization rate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 824–829, 2003     

Effect of compatibilizer in acrylonitrile‐butadiene‐styrene toughened nylon 6 blends: Ductile–brittle transition temperature

The ductile–brittle transition temperatures were determined for compatibilized nylon 6/acrylonitrile‐butadiene‐styrene (PA6/ABS) copolymer blends. The compatibilizers used for those blends were methyl methacrylate‐co‐maleic anhydride (MMA‐MAH) and MMA‐co‐glycidyl methacrylate (MMA‐GMA). The ductile–brittle transition temperatures were found to be lower for blends compatibilized through maleate modified acrylic polymers. At room temperature, the PA6/ABS binary blend was essentially brittle whereas the ternary blends with MMA‐MAH compatibilizer were supertough and showed a ductile–brittle transition temperature at ?10°C. The blends compatibilized with maleated copolymer exhibited impact strengths of up to 800 J/m. However, the blends compatibilized with MMA‐GMA showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2643–2647, 2003     

Dynamic mechanical properties of polypropylene‐g‐maleic anhydride and ethylene–propylene–diene terpolymer blends: Effect of blend preparation methods

In this work, we attempted two different ways of processing to improve interfacial adhesion of polypropylene (PP) and ethylene–propylene–diene terpolymer (EPDM) by introducing maleic anhydride (MAH); In one way, the in situ grafting and dynamic vulcanization (ISGV) were performed simultaneously from PP and EPDM with MAH in the presence of dicumyl peroxide (DCP) in an intensive mixer. In another way, PP was first grafted with MAH and then the PP‐g‐MAH was blended with EPDM in the intensive mixer in the presence of DCP by the dynamic vulcanization (DV). It was found that the glass transition temperatures (T_gs) of both PP and EPDM phases were shifted to higher temperature as the EPDM content increased for the blends prepared by both IGSV and DV methods, mainly due to the crosslinking of EPDM. The higher T_gs and larger storage moduli were observed for the blends prepared by the ISGV method than those prepared by the DV method, while the morphology showed that the size reduction of dispersed particles in latter blends was larger than that of the former blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2777–2784, 2000     

Influence of premade and in situ compatibilizers in polypropylene/ethylene–propylene–diene terpolymer thermoplastic elastomeric olefins and thermoplastic vulcanizates

During dynamic vulcanization of polypropylene (PP)/ethylene–propylene–diene terpolymer (EPDM) blends with dicumyl peroxide/triallyl cyanurate, there is a possibility of the generation of in situ graft links at the interface. Three potential compatibilizers (PP‐grafted EPDM, styrene–ethylenebutylene–styrene, and trans‐polyoctenamer) for PP/EPDM blends were first investigated as references to obtain a quantified insight into the effects to be expected from in situ graft links. Only the first compatibilizer showed some compatibilizing action in straight, unvulcanized blends, as evidenced by a slight increase in the tensile strength of the blend and a somewhat smaller EPDM particle size within the PP matrix. Also, dynamic mechanical testing, in particular, the glass‐transition temperatures of the PP and EPDM components, showed some signs of compatibilization. The PP‐grafted EPDM resembled most closely the structures of PP and EPDM. In the spectra obtained with high temperature, solid‐state NMR, there was an indication that PP–EPDM graft links were generated during the dynamic vulcanization process that still remained after the extraction of the free PP phase from the thermoplastic vulcanizate film. NMR relaxation experiments gave further evidence for the graft links formed in situ. In all cases, only qualitative indications could be achieved because of the extremely low number of graft links formed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3877–3888, 2006     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Differential scanning calorimetric and free volume study of reactive compatibilization by EPM‐g‐MA of poly(trimethylene terephthalate)/EPDM blends

Differential scanning calorimetry (DSC) and positron annihilation lifetime measurements have been carried out to study the effect of the compatibilizer maleic anhydride grafted ethylene propylene copolymer (EPM‐g‐MA) in poly trimethylene terephthalate and ethylene propylene diene monomer (PTT/EPDM) immiscible blends. The DSC results for the blends of 50/50 and 30/70 compositions show two clear glass transition temperatures, indicating that the blends are two‐phase systems. With the addition of compatibilizer, the separation between the two glass transitions decreased, suggesting an increased interaction between the blend components with compatibilizer. At 5 wt % of compatibilizer, the separation between the T_gs reduced in both 50/50 and 30/70 blends. The positron results for the blends without compatibilizer showed an increase in relative fractional free volume, as the EPDM content in the blend is increased. This suggests the coalescence of free volume of EPDM with the free volumes of PTT due to phase separation. However, the effect of compatibilizer in the blends was clearly seen with the observed minimum in free volume parameters at 5% of the compatibilizer, further suggesting that this percent of compatibilizer seems to be the optimum value for these blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 740–747, 2006     

Effects of EPDM‐g‐MAH compatibilizer and internal mixer processing parameters on the properties of NR/EPDM blends: An analysis using response surface methodology

This study evaluates the effects of ethylene‐propylene‐diene‐monomer grafted maleic anhydride (EPDM‐g‐MAH) and internal mixer melt compounding processing parameters on the properties of natural rubber/ethylene‐propylene‐diene rubber (NR/EPDM) blends. Using Response Surface Methodology (RSM) of 2⁵ two‐level fractional factorial, we studied the effects of NR/EPDM ratio, mixing temperature, Banbury rotor speed, mixing period, and EPDM‐g‐MAH contents in NR/EPDM blends. The study found that the presence of EPDM‐g‐MAH in NR/EPDM blends had a predominant role as a compatibilizing agent, which affected the processability and properties of the final material. We also determined the model fitting with constant determination, R² of 99.60% for tensile strength (TS) response with a suggested combination of mixing process input parameters. The reproducibility of the proposed mixing strategy was then confirmed through model validation with a minor deviation at +2.303% and higher desirability of 0.960. This study is essential in providing a process design reference for NR/EPDM blends preparation by melt‐blending and the role of a compatibilizer from the systematic Design of Experiment (DOE) approach. The experimental findings were further supported with swelling and cross‐link density measurements, differential scanning calorimetry analysis, and observation of fracture morphology using a scanning electron microscope. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42199.     

EPDM/St‐An graft copolymerization reaction behavior by phase inversion emulsion and the toughness effect of EPDM‐g‐SAN on SAN resin

Styrene‐EPDM‐acrylonitrile tripolymer (EPDM‐g‐SAN) was synthesized by the graft copolymerization of styrene (St) and acrylonitrile (An) onto ethylene‐propylene‐diene terpolymer (EPDM) with “phase inversion” emulsification technique. The high impact strength engineering plastics AES was the blend of SAN resin and EPDM‐g‐SAN, which occupied good weathering and yellow discoloration resistivity. The effects of An percentage in comonomer and the weight proportion of EPDM to St‐An on graft copolymerization behavior and AES notched impact strength were studied. The results showed that monomer conversion ratio (CR) exhibited a peak when the An percentage changed, and the maximum value was 97.5%. Grafting ratio (GR) and grafting efficiency (GE) enhance as well. The notched impact strength of AES presented a peak with the maximum value of 53.0 KJ/m², when An percentage was at the range of 35–40%. The spectra of FTIR showed that St and An were graft onto the EPDM. DSC analysis illuminated that T_g of EPDM phase in the blends was lower than that of the pure EPDM. TEM and SEM micrographs indicated that the polarity of g‐SAN of EPDM‐g‐SAN was the main factor effect the particle morphology, in terms of size, distribution and isotropy. When weight ratio of St to An was 65/35, the polarity of g‐SAN chains was appropriate, and the EPDM‐g‐SAN particles dispersed well in the SAN matrix. The super impact toughness is interpreted in terms of EPDM phase cavitation and enhanced plastic shear yielding. The highest toughness occurs at an optimum EPDM‐g‐SAN phase particle size which is about 0.2 μm in SAN resin matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Physical properties of poly(vinyl chloride)–grafted N‐isopropylacrylamide graft copolymers and corresponding polyblends

The physical properties of poly(vinyl chloride) (PVC) and poly(N‐isopropylacrylamide) [poly(NIPAAm)] blend systems, and their corresponding graft copolymers such as PVC‐g‐NIPAAm, were investigated in this work. The compatible range for PVC–poly(NIPAAm) blend systems is less than 15 wt % poly(NIPAAm). The water absorbencies for the grafted films increase with increase in graft percentage. The water absorbencies for the blend systems increase with increase in poly(NIPAAm) content within the compatible range for the blends, but the absorbencies decrease when the amount of poly(NIPAAm) is more than the compatible range in the blend system. The tensile strengths for the graft copolymers are larger than the corresponding blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 170–178, 2000     

Graft‐modified HCPE with methyl methacrylate by the mechanochemistry reaction. II. Physical‐mechanical properties and processability

In this article, the physical‐mechanical properties and processability of graft‐modified highly chlorinated polyethylene (HCPE; chlorine contents: ≥ 60%) with methyl methacrylate (MMA) by mechanochemistry reaction were studied. The results showed that the HCPE‐g‐MMA system is superior to unmodified HCPE in physical‐mechanical properties, particularly in processability. In addition, the HCPE‐g‐MMA system, with about 62% chlorine content, was the same as PVC in its physical‐mechanical properties. The HCPE‐g‐MMA system, with about 65.5% chlorine content, is the same as chlorinated poly(vinyl chloride) (CPVC) in its physical‐mechanical properties, except that the Vicat softening temperature and processability of HCPE‐g‐MMA system are superior to PVC and CPVC. Compared with PVC and CPVC, the HCPE‐g‐MMA system proves better due to its lack of a toxic monomer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 282–287, 2004     

Rheological and curing behavior of reactive blending. II. Natural rubber‐g‐poly(methyl methacrylate)–cassava starch

Graft copolymers of natural rubber (NR) and methyl methacrylate (MMA) were prepared using cumene hydroperoxide and tetraethylene pentamine as redox initiators via the semibatch emulsion polymerization technique. Various molar percentage ratios of NR/MMA were studied in the grafting reaction (i.e., 95/5, 90/10, 80/20, 70/30, and 60/40). The graft copolymer with a 70/30 molar ratio was selected and used to prepare rubber blends with cassava starch. The starch was used at levels of 0, 20, 40, and 60 phr. Another set of rubber blends was prepared for comparison purposes. The NR‐g‐poly(MMA) (PMMA, 75 phr) was blended with 25 phr of NR air dried sheets (ADS) and a given level of the cassava starch. We found that the Mooney viscosity, shear stress, and shear viscosity increased with an increasing concentration of cassava starch. This may be attributed to the chemical interactions between the polar groups of the NR‐g‐PMMA and the cassava starch. The blends were later compounded using a compounding formulation according to ASTM D 3184‐89. A similar short delay onset of vulcanization (i.e., approximately 1 min) was observed for the whole set of compounds under study. However, different curing characteristics were observed for the blends of NR‐g‐PMMA–cassava starch and NR‐g‐PMMA–ADS–cassava starch. The NR‐g‐PMMA–cassava starch compounds exhibited two‐stage curing characteristics. The curing curve had a slight reversion at a testing time of approximately 8 min. The shear modulus then abruptly increased with an increasing testing time in the range of 20–60 min. The curing curves for NR‐g‐PMMA–ADS–cassava starch blends exhibited a single curing stage with a shear modulus that increased slightly with the testing time was increased from 20 to 60 min. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1453–1463, 2003     

Preparation and properties of compatibilized PVC/SMA‐g‐PA6 blends

The morphology and mechanical properties of PVC/SMA‐g‐PA6 blends were investigated in this paper. Graft to polymer SMA‐g‐PA6 was prepared via a solution graft reaction between SMA and PA6. FTIR test evidences the occurrence of the graft reaction between SMA and PA6. DSC analysis shows that SMA‐g‐PA6 has a lower melting point of 187°C, which may result in a decrease in crystallinity of PA6 and thus enable efficient blending of SMA‐g‐PA6 and PVC. Compatibilization was evidenced by the dramatic increase in mechanical properties, the smaller particle size and finer dispersion of PA6 in PVC matrix, and, further, a cocontinuous morphology at 16 wt % SMA‐g‐PA6 content. SMA‐g‐PA6 from the solution graft reaction can toughen and reinforce PVC material. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 432–439, 2004     

Compatibilizing effect of ethylene–propylene–diene grafted maleic anhydride terpolymer on the blend of polyamide 66 and thermal liquid crystalline polymer

Polyamide 66–thermal liquid crystalline polymer (PA66/TLCP) composites containing 10 wt% TLCP was compatibilized by ethylene–propylene–diene‐grafted maleic anhydride terpolymer (MAH‐g‐EPDM). The blending was performed on a twin‐screw extrusion, followed by an injection molding. The rheological, dynamic mechanical analysis (DMA), thermal, mechanical properties, as well as the morphology and FTIR spectra, of the blends were investigated and discussed. Rheological, DMA, and FTIR spectra results showed that MAH‐g‐EPDM is an effective compatibilizer for PA66/TLCP blends. The mechanical test indicated that the tensile strength, tensile elongation, and the bending strength of the blends were improved with the increase of the content of MAH‐g‐EPDM, which implied that the blends probably have a great frictional shear force, resulting from strong adhesion at the interface between the matrix and the dispersion phase; while the bending modulus was weakened with the increase of MAH‐g‐EPDM content, which is attributed to the development of the crystalline phase of PA66 hampered by adding MAH‐g‐EPDM. POLYM. COMPOS., 27:608–613, 2006. © 2006 Society of Plastics Engineers