SORPTION,DIFFUSION, AND PERMEATION OF CHLORINATED HYDROCARBON VAPORS THROUGH NATURAL RUBBER,EPOXIDIZED NATURAL RUBBER,AND THEIR BLENDS

The study investigates the transport process of various chlorinated hydrocarbons through natural rubber (NR), epoxidized natural rubber (ENR), and their blends. The effect of structure and morphology of the membranes on the transport parameters has been investigated. Sorption coefficient is found to increase and the permeability coefficient shows the reverse trend with increasing epoxy content. As the mol% epoxidation increases, the polymeric network structure becomes more compact, which leads to a decrease in the diffusion coefficient, which ultimately results in a low permeation coefficient. The morphology of NR/ENR blends has been investigated by combining scanning electron microscopy with permeability measurements. The permeation coefficient is found to be minimum for the NR/ENR 70/30 composition; a 50/50 composition shows the maximum. The heterogeneous morphology of 70/30 NR/ENR blend results in the low permeability coefficient, whereas the co-continuous nature of the 50/50 composition accounts for the maximum permeability. Permeability measurements provide the most useful information about the way morphology is changing with composition of the blends and about the composition corresponding to the maximum level of co-continuity of the two phases.     

Separation of alkane–acetone mixtures using styrene–butadiene rubber/natural rubber blend membranes

Conventionally vulcanized styrene–butadiene rubber/natural rubber blend membranes were prepared for the pervaporation separation of alkane–acetone mixtures. Swelling measurements were carried out in both acetone and n‐alkanes to investigate the swelling behavior of the membranes. The swelling behavior was found to depend on the composition of the blend. The effects of blend ratio, feed composition, and penetrant size on the pervaporation process were analyzed. The permeation properties have been explained on the basis of interaction between the membrane and solvents and blend morphology. The SBR/NR 70/30 blend membrane showed higher selectivity among all the membranes used. Flux increases with increasing alkane content in the feed composition. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3059–3068, 1999     

环氧化天然橡胶共交联改性EPDM/NR共混物的性能

将三元乙丙橡胶(EPDM)与环氧化天然橡胶(ENR)共交联改性后,再与天然橡胶(NR)共混,考察了ENR共交联改性EPDM/NR共混胶的硫化特性、硫化胶的物理机械性能、溶胀指数和耐热空气老化性能,并对该硫化胶进行了差示扫描量热分析。结果表明,EPDM经过ENR共交联改性后与NR共混,ENR共交联改性EPDM/NR共混胶的交联程度明显提高,各相达到了同步交联,硫化胶的综合性能得到了显著改善。     

Thermoplastic natural rubber based on polyamide‐12: Influence of blending technique and type of rubber on temperature scanning stress relaxation and other related properties

Thermoplastic natural rubber based on polyamide‐12 (PA‐12) blend was prepared by melt blending technique. Influence of blending techniques (i.e., simple blend and dynamic vulcanization) and types of natural rubber (i.e., unmodified natural rubber (NR) and epoxidized natural rubber (ENR)) on properties of the blends were investigated. It was found that the simple blends with the proportion of rubber ～ 60 wt % exhibited cocontinuous phase structure while the dynamically cured blends showed dispersed morphology. Furthermore, the blend of ENR exhibited superior mechanical properties, stress relaxation behavior, and fine grain morphology than those of the blend of the unmodified NR. This is attributed to chemical interaction between oxirane groups in ENR molecules and polar functional groups in PA‐12 molecules which caused higher interfacial adhesion. It was also found that the dynamic vulcanization caused enhancement of strength and hardness properties. Temperature scanning stress relaxation measurement revealed improvement of stress relaxation properties and thermal resistance of the dynamically cured ENR/PA‐12 blend. This is attributed to synergistic effects of dynamic vulcanization of ENR and chemical reaction of the ENR and PA‐12 molecules. Furthermore, the dynamically cured ENR/PA‐12 blend exhibited smaller rubber particles dispersed in the PA‐12 matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties and blend compatibility of natural rubber –chlorosulfonated polyethylene blends

Natural rubber (NR) was blended with chlorosulfonated polyethylene (CSM) with various formulation and blend ratios (NR/CSM: 80/20 –20/80, wt/wt). Rubber blends were prepared by using a two‐roll mill and vulcanized in a compression mold to obtain the 2 mm‐thick sheets. Tensile properties, tear resistance, thermal aging resistance, ozone resistance, and oil resistance were determined according to ASTM. Compatible NR/CSM blends are derived from certain blends containing 20–30% CSM without adding any compatibilizing agent. Tensile and tear strength of NR‐rich blends for certain formulations show positive deviation from the rule of mixture. Thermal aging resistance depends on formulation and blend ratio, while ozone and oil resistance of the blends increase with CSM content. Homogenizing agents used were Stuktol®60NS and Epoxyprene®25. Stuktol®60NS tends to decrease the mechanical properties of the blends and shows no significant effect on blend morphology. Addition of 5–10 phr of epoxidized natural rubber (ENR, Epoxyprene® 25) increases tensile strength, thermal aging resistance, and ozone resistance of the blends. It is found that ENR acts as a compatibilizer of the NR/CSM blends by decreasing both CSM particle size diameter and α transition temperature of CSM. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 127–140, 2006     

天然橡胶增韧聚氯乙烯的研究

采用未改性的标准天然橡胶(NR)作增韧剂,通过机械共混法制备增韧聚氯乙烯(PVC)复合材料,考察了NR和增容剂用量对PVC增韧效果以及力学性能的影响.结果表明:当NR用量为10份时,材料的冲击强度最高为24.87 kJ/m2;加入增容剂环氧化天然橡胶(ENR)后,材料的冲击强度随其用量的增加而增大,在ENR为5份时其冲击强度为69.86 kJ/m2;氯化聚乙烯(CPE)作增容剂时,其冲击强度先升后降,在4份时达到峰值103.93 kJ/m2;氯化橡胶(CNR)作增容剂在3份时,其冲击强度达到最佳值35.37 kJ/m2;增容增韧后共混物的拉伸强度普遍降低.     

Development of novel elastomeric blends containing natural rubber and ultra-low-density polyethylene

This study sought to develop novel elastomeric compounds using natural rubber (NR) and ultra-low-density polyethylene (ULDPE). Blends were prepared by means of a two-roll mill for three ratios (70/30, 60/40, and 50/50 NR/ULDPE). Conventional vulcanization was performed in a compression mold. The physical and mechanical properties of the blend were determined according to ASTM standards. The results were compared with those obtained from NR blended with styrene-butadiene rubber (SBR). The morphological examinations with scanning electron microscopy indicated that ULDPE was compatible with NR; thus, the addition of a compatibilizer was not necessary. The cocontinuous phase was dominant in the NR/ULDPE blend containing 50 and 60 wt % NR. The tensile properties, tear resistance, and aging resistance of the NR/ULDPE blends were found to be superior to those of NR/SBR blends. On the other hand, the abrasion and flex cracking resistances of the NR/ULDPE blend were inferior to those exhibited by SBR blends but the Mooney viscosity and resilience of both blends fell in the same range. However, the addition of dicumyl peroxide appeared to have caused crosslinking of the ULDPE phase in the blend, which in turn increased the tensile properties and abrasion and aging resistance. The properties of the tertiary NR/SBR/ULDPE blend were investigated as well. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 650–660, 2001     

Toughness enhancement of poly(lactic acid) by melt blending with natural rubber

Rubber toughened poly(lactic acid) (PLA) was prepared by blending with natural rubber (NR)‐based polymers. The blends contained 10 wt % of rubber and melt blended with a twin screw extruder. Enhancement of impact strength of PLA was primarily concernced. This study was focused on the effect of rubber polarity, rubber viscosity and molecular weight on mechanical properties of the blends. Three types of rubbers were used: NR, epoxidized natural rubber (ENR25 and ENR50), and natural rubber grafted with poly(methyl methacrylate) (NR‐g‐PMMA). Effect of viscosity and molecular weight of NR, rubber mastication with a two‐roll mill was investigated. It was found that all blends showed higher impact strength than PLA and NR became the best toughening agent. Viscosity and molecular weight of NR decreased with increasing number of mastication. Impact strength of PLA/NR blends increased after applying NR mastication due to appropriate particle size. DMTA and DSC characterization were determined as well. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

环氧化天然橡胶的研究与应用

环氧化天然橡胶（ENR）是由NR化学改性而成,笔者阐述了环氧化天然橡胶制备原理和方法、环氧化天然橡胶性能及应用研究、环氧化天然橡胶共混改性研究,其中包括ENR与PVC共混体系的研究、ENR其它共混体系的研究和ENR改性的研究.     

液体聚丁二烯橡胶对顺丁橡胶/天然橡胶共混胶加工性能及抗疲劳性能的影响

考察了液体聚丁二烯橡胶Activ-50对顺丁橡胶(BR)/天然橡胶(NR)共混胶加工性能及抗疲劳性能的影响,并采用裂纹增长测试平台结合有限元ABAQUS/CAE,从疲劳裂纹扩展角度对硫化胶的抗疲劳性能进行了考察.结果表明,Activ-50能够降低混炼胶的储能模量和黏度,橡胶共混过程中加入Activ-50能改善体系的加工...     

Thermoplastic vulcanizates based on epoxidized natural rubber/polypropylene blends: Effect of compatibilizers and reactive blending

Epoxidized natural rubber (ENR) was prepared using the performic epoxidation method. TPVs based on ENR/PP blends were later prepared by melt‐mixing processes via dynamic vulcanization. The effects of blend ratios of ENR/PP, types of compatibilizers, and reactive blending were investigated. Phenolic modified polypropylene (Ph‐PP) and graft copolymer of maleic anhydride on polypropylene molecules (PP‐g‐MA) were prepared and used as blend compatibilizers and reactive blending components of ENR/Ph‐PP and ENR/PP‐g‐MA blends. It was found that the mixing torque, apparent shear stress and apparent shear viscosity increased with increasing levels of ENR. This is attributed to the higher viscosity of the pure ENR than that of the pure PP. Furthermore, there was a higher compatibilizing effect because of the chemical interaction between the polar groups in ENR and PP‐g‐MA or Ph‐PP. Mixing torque, shear flow properties (i.e., shear stress and shear viscosity) and mechanical properties (i.e., tensile strength, elongation at break, and hardness) of the TPVs prepared by reactive blending of ENR/Ph‐PP and ENR/PP‐g‐MA were lower than that of the samples without a compatibilizer. However, the TPVs prepared using Ph‐PP and PP‐g‐MA as compatibilizers exhibited higher values. We observed that the TPVs prepared from ENR/PP with Ph‐PP as a compatibilizer gave the highest rheological and mechanical properties, while the reactive blending of ENR/PP exhibited the lowest values. Trend of the properties corresponds to the morphology of the TPVs. That is, the TPV with Ph‐PP as a blend compatibilizer showed the smallest rubber particles dispersed in the PP matrix, while the reactive blending of ENR/PP‐g‐MA showed the largest particles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4729–4740, 2006     

Novel ternary blends of natural rubber/linear low-density polyethylene/thermoplastic starch: influence of epoxide level of epoxidized natural rubber on blend properties

Novel degradable materials based on ternary blends of natural rubber (NR)/linear low-density polyethylene (LLDPE)/thermoplastic starch (TPS) were prepared via simple blending technique using three different types of natural rubber (i.e., unmodified natural rubber (RSS#3) and ENR with 25 and 50 mol% epoxide). The evolution of co-continuous phase morphology was first clarified for 50/50: NR/LLDPE blend. Then, 10 wt% of TPS was added to form 50/40/10: NR/LLDPE/TPS ternary blend, where TPS was the particulate dispersed phase in the NR/LLDPE matrix. The smallest TPS particles were observed in the ENR-50/LLDPE blend. This might be attributed to the chemical interactions of polar functional groups in ENR and TPS that enhanced their interfacial adhesion. We found that ternary blend of ENR-50/LLDPE/TPS exhibited higher 100 % modulus, tensile strength, hardness, storage modulus, complex viscosity and thermal properties compared with those of ENR-25/LLDPE/TPS and RSS#3/LLDPE/TPS ternary blends. Furthermore, lower melting temperature (T _m) and heat of crystallization of LLDPE (?H) were observed in ternary blend of ENR-50/LLDPE/TPS compared to the other ternary blends. Also, neat TPS exhibited the fastest biodegradation by weight loss during burial in soil for 2 or 6 months, while the ternary blends of NR/LLDPE/TPS exhibited higher weight loss compared to the neat NR and LLDPE. The lower weight loss of the ternary blends with ENR was likely due to the stronger chemical interfacial interactions. This proved that the blend with ENR had lower biodegradability than the blend with unmodified NR.     

Rheological behavior of reactive blending of epoxidized natural rubber with cassava starch and epoxidized natural rubber with natural rubber and cassava starch

Epoxidized natural rubbers (ENR‐25 and ENR‐45) were prepared using the performic epoxidation method. Two‐component (ENR–cassava starch) and three‐component (ENR–NR–cassava starch) blends were prepared. ENR‐25 and ENR‐45 were blended with various quantities of gelatinized cassava starch in the latex state. The pure ENR exhibited lower shear stress and shear viscosity than those of the blends with cassava starch. Furthermore, the shear stress and shear viscosity were increased with an increase in the cassava starch concentration. The chemical interaction between the epoxide groups in the ENR and the hydroxyl groups in the cassava starch molecules might be the reason for the increasing trends of the shear stress and shear viscosity. The blends are classified as compatible blends because of the strong chemical bonding between different phases. SEM micrographs were used to clarify the compatibility. Power law behavior with pluglike flow profiles was observed for all sets of ENR–NR–cassava starch blends. Very low power law index values (<0.34) and highly pseudoplastic fluid behavior were also observed. The log additive rule was applied to plots of zero shear viscosity (consistency index) and the shear viscosity versus the concentration of ENR‐25. Positive deviation blending was observed, which indicates compatible blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1752–1762, 2004     

Effect of glycidyl methacrylate-grafted natural rubber on physical properties of polylactic acid and natural rubber blends

Natural rubber (NR) was melt blended with polylactic acid (PLA) at various ratios using an internal mixer. The impact strength and elongation at break of PLA/NR blend dramatically increased with increasing NR content up to 10% (w/w). Glycidyl methacrylate-grafted natural rubber (NR-g-GMA) was used as a compatibilizer for PLA/NR blend. The effects of content and %grafting of NR-g-GMA on mechanical properties of PLA/NR blend were studied. The experimental result showed that the addition of NR-g-GMA in PLA/NR blend significantly improved impact strength and elongation at break of PLA/NR blend when compared with that of neat PLA and PLA/NR blend without NR-g-GMA. The impact strength and elongation at break of PLA/NR blend increased with increasing NR-g-GMA content up to 1% (w/w). Moreover, with increasing % grafting of NR-g-GMA in PLA/NR blend up to 4.35, the impact strength and elongation at break of the blend increased. Morphological and thermal property of PLA, PLA/NR, and PLA/NR/NR-g-GMA were elucidated as well. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nanoclay distribution and its influence on the mechanical properties of rubber blends

The distribution of modified and unmodified nanoclays inside the rubber phases of immiscible rubber–rubber blends composed of nonpolar–polar natural rubber (NR)/epoxidized natural rubber (ENR) and nonpolar–nonpolar NR/polybutadiene rubber (BR) was investigated for the first time. The distribution of clays at various loadings in the blends was calculated from the viscoelastic properties of the blends. For example, in the 50 : 50 NR/ENR blend, 42% Cloisite 30B migrated to the NR phase, and 58% went to the ENR phase. However, in the same blend, only 7% Cloisite Na⁺ was found in the NR phase, and 93% was found in the ENR phase. Again, in the 50 : 50 NR/BR blends, the NR phase contained 85% Cloisite 30B, whereas 55% Cloisite Na⁺ migrated to the NR phase. All these observations were explained with the help of viscosity, X‐ray diffraction, and morphology analyses. The effect of the distribution of the clay on the mechanical properties was also discussed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

环氧化天然橡胶复合材料性能研究

采用新方法制备环氧化天然橡胶(ENR)/白炭黑和天然橡胶(NR)/ENR/白炭黑复合材料,并对其性能进行研究。结果表明:ENR/白炭黑复合材料的热稳定性优于ENR;在NR/ENR并用胶中加入白炭黑和硅烷偶联剂KH-550,NR/ENR/白炭黑复合材料0℃时的损耗因子(tanδ)增大,65℃时的tanδ值减小,复合材料的抗湿滑性能提高,滚动阻力减小。     

Effect of surface modification of silicon carbide nanoparticles on the properties of nanocomposites based on epoxidized natural rubber/natural rubber blends

Improvement of the properties of rubber nanocomposites is a challenge for the rubber industry because of the need for higher performance materials. Addition of a nanometer‐sized filler such as silicon carbide (SiC) to enhance the mechanical properties of rubber nanocomposites has rarely been attempted. The main problem associated with using SiC nanoparticles as a reinforcing natural rubber (NR) filler compound is poor dispersion of SiC in the NR matrix because of their incompatibility. To solve this problem, rubber nanocomposites were prepared with SiC that had undergone surface modification with azobisisobutyronitrile (AIBN) and used as a filler in blends of epoxidized natural rubber (ENR) and natural rubber. The effect of surface modification and ENR content on the curing characteristics, dynamic mechanical properties, morphology and heat buildup of the blends were investigated. The results showed that modification of SiC with AIBN resulted in successful bonding to the surface of SiC. It was found that modified SiC nanoparticles were well dispersed in the ENR/NR matrix, leading to good filler‐rubber interaction and improved compatibility between the rubber and filler in comparison with unmodified SiC. The mechanical properties and heat buildup when modified SiC was used as filled in ENR/NR blends were improved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45289.     

Comparison of thermoset soy protein resin toughening by natural rubber and epoxidized natural rubber

Fully bio‐based soy protein isolate (SPI) resins were toughened using natural rubber (NR) and epoxidized natural rubber (ENR). Resin compositions containing up to 30 wt % NR or ENR were prepared and characterized for their physical, chemical and mechanical properties. Crosslinking between SPI and ENR was confirmed using ¹H‐NMR and ATR‐FTIR. All SPI/NR resins exhibited two distinctive drops in their modulus at glass transition temperature (T_g ) and degradation temperature (T_d ) at around ?50 and 215 °C, corresponding to major segmental motions of NR and SPI, respectively. SPI/ENR resins showed similar T_g and T_d transitions at slightly higher temperatures. For SPI/ENR specimens the increase in ENR content from 0 to 30 wt % showed major increase in T_g from ?23 to 13 °C as a result of crosslinking between SPI and ENR. The increase in ENR content from 0 to 30 wt % increased the fracture toughness from 0.13 to 1.02 MPa with minimum loss of tensile properties. The results indicated that ENR was not only more effective in toughening SPI than NR but the tensile properties of SPI/ENR were also significantly higher than the corresponding compositions of SPI/NR. SPI/ENR green resin with higher toughness could be used as fully biodegradable thermoset resin in many applications including green composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44665.     

Morphology,mechanical and viscoelastic properties of nitrile rubber/epoxidized natural rubber blends

A new class of blend membranes from blends of nitrile rubber (NBR) and epoxidized natural rubber (ENR) has been prepared and their morphology, miscibility, mechanical, and viscoelastic properties have been studied. The ebonite method was used to study the blend morphology of the membranes. The morphology of the blends indicated a two‐phase structure in which the minor phase is dispersed as domains in the major continuous phase. The performance of NBR/ENR blend membranes has been studied from the mechanical measurements. The viscoelastic behavior of the blends has been analyzed from the dynamic mechanical data. An attempt was made to relate the viscoelastic behavior with the morphology of the blends. Various composite models have been used to predict the experimental viscoelastic data. The area under the linear loss modulus curve was larger than that obtained by theoretical group contribution analysis. The homogeneity of the system was further evaluated by Cole–Cole analysis. Finally, a master curve for the modulus of the blend was generated by applying the time–temperature superposition principle. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1561–1573, 2005     

Thermoplastic vulcanizates based on poly(methyl methacrylate)/epoxidized natural rubber blends: Mechanical,thermal, and morphological properties

Epoxidized natural rubbers (ENRs) with epoxide levels of 10, 20, 30, 40 and 50 mol % were prepared. The ENRs were later used to prepare thermoplastic vulcanizates (TPVs) by blending them with poly(methyl methacrylate) (PMMA) using various formulations. Dynamic vulcanization, using sulfur as a vulcanizing agent, was performed during the mixing process. The mixing torque increased as the ENR contents and epoxide molar percentage increased. This was because of an increasing chemical interaction between the polar groups of the blend components, particularly at the interface between the elastomeric and thermoplastic phases. The ultimate tensile strength of the TPVs with ENR‐20 was high because of strain‐induced crystallization. ENRs with epoxide levels >30 mol % exhibited an increase of tensile strength because of increasing levels of chemical interaction between the molecules and the different phases. The hardness of the TPVs also increased with increased epoxide levels but decreased with increased contents of ENRs. Two morphology phases with small domains of vulcanized ENR particles dispersed in the PMMA matrix were observed from scanning electron microscopy micrographs. The TPVs based on ENR‐20 and ENR‐50 showed smaller dispersed rubber domains than those of the other types of ENRs. Furthermore, the size of the vulcanized rubber domain decreased with increasing amounts of PMMA in the blends. The decomposition temperature of the TPVs also increased as both the levels of ENRs in the blends and the epoxide molar percentage increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1251–1261, 2005