Effects of lubricating‐oil additives on the friction and wear properties of polymers and their composites sliding against steel under oil‐lubricated conditions

The effects of lubricating‐oil additive zinc dialkyldithiophosphate (ZDDP) on the friction and wear properties of polymers and their composites sliding against GCr15 bearing steel were studied by using an MHK‐500 ring‐on‐block wear tester (Timken wear tester). Then the frictional surfaces of the friction pairs were examined by using electron probe microanalysis (EPMA). Experimental results show that the ZDDP contained in liquid paraffin has little effect on the friction coefficients of the polyimide (PI) or polyamide 66 (PA66) against GCr15 bearing steel friction pairs compared with that under the lubrication of liquid paraffin, but it slightly reduces the friction coefficients of polytetrafluoroethylene (PTFE) or its composites against GCr15 bearing steel friction pairs. Under lubrication of liquid paraffin containing 2 wt % ZDDP, the ZDDP film absorbed on the frictional surfaces of the PTFE composites–GCr15 bearing steel friction pairs exhibits obvious antiwear properties; it greatly reduces the wear of pure PTFE and the PTFE composites filled with Pb, PbO, and MoS₂; and the wear of the PTFE composites can be reduced by one order of magnitude compared with that under lubrication of pure liquid paraffin. Meanwhile, the inorganic fillers Pb, PbO, and MoS₂ contained in PTFE have little effect on the absorption of ZDDP to the frictional surfaces, so they have little effect on the friction coefficients of the PTFE composites–GCr15 bearing steel friction pairs under the lubrication of liquid paraffin containing 2 wt % ZDDP. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1240–1247, 2000     

Friction and wear characteristics of copper and its compound-filled PTFE composites under oil-lubricated conditions

Four kinds of polytetrafluoroethylene (PTFE)-based composites, such as pure PTFE, PTFE + 30(v)%Cu, PTFE + 30(v)%Cu₂O, and PTFE + 30(v)%CuS composite, were prepared. Then the friction and wear properties of the PTFE composites filled with Cu, Cu₂O, or CuS sliding against GCr15-bearing steel under both dry and liquid paraffin-lubricated conditions were studied by using an MHK-500 ring-block wear tester. Finally, the worn surfaces and the transfer films of these PTFE composites formed on the surface of GCr15-bearing steel were investigated by using a scanning electron microscope (SEM) and an optical microscope, respectively. Experimental results show that the antiwear properties of these PTFE composites can be greatly improved by filling Cu, Cu₂O, or CuS to PTFE, and the wear of these PTFE composites can be decreased by two orders of magnitude compared to that of pure PTFE under dry friction conditions. Meanwhile, CuS increases the friction coefficient of the PTFE composite, but Cu and Cu₂O reduce the friction coefficients of the PTFE composites. However, the friction and wear properties of Cu, Cu₂O, or CuS-filled PTFE composites can be greatly improved by lubrication with liquid paraffin. The friction coefficients of these PTFE composites can be decreased by one order of magnitude compared to those under dry friction conditions, while the wear of these PTFE composites can be decreased by one to two orders of magnitude. The PTFE + 30(v)%Cu composite exhibits excellent friction and wear-reducing properties under higher loads in liquid paraffin-lubricated conditions, so the PTFE + 30(v)%Cu composite is much more suitable for application under oil-lubricated conditions in practice. Optical microscope investigation of transfer films shows that Cu, Cu₂O, and CuS enhance the adhesion of the transfer films to the surface of GCr15-bearing steel, so they greatly reduce the wear of the PTFE composites. However, the transfer of the PTFE composites onto the surface of GCr15-bearing steel can be greatly reduced by lubrication with liquid paraffin, but the transfer still takes place. SEM examination of worn surfaces shows that the interaction between liquid paraffin and the PTFE composites, especially the absorption of liquid paraffin into the surface layers of the PTFE composites, creates some cracks on the worn surfaces of Cu₂O or CuS-filled PTFE composites, the creation and development of the cracks reduces the load-carrying capacity of the PTFE composites; this leads to the deterioration of the friction and wear properties of the PTFE composites under higher loads in liquid paraffin lubrication. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1455–1464, 1998     

Friction and wear characteristics of ceramic particle filled polytetrafluoroethylene composites under oil-lubricated conditions

Five kinds of polytetrafluoroethylene (PTFE)-based composites were prepared: PTFE, PTFE + 30 vol % SiC, PTFE + 30 vol % Si₃N₄, PTFE + 30 vol % BN, and PTFE + 30 vol % B₂O₃. The friction and wear properties of these ceramic particle filled PTFE composites sliding against GCr15 bearing steel under both dry and liquid paraffin lubricated conditions were studied by using an MHK-500 ring-block wear tester. The worn surfaces and the transfer films formed on the surface of the GCr15 bearing steel of these PTFE composites were investigated by using a scanning electron microscope (SEM)and an optical microscope, respectively. The experimental results show that the ceramic particles of SiC, Si₃N₄, BN, and B₂O₃ can greatly reduce the wear of the PTFE composites; the wear-reducing action of Si₃N₄ is the most effective, that of SiC is the next most effective, then the BN, and that of B₂O₃ is the worst. We found that B₂O₃ reduces the friction coefficient of the PTFE composite but SiC, Si₃N₄, and BN increase the friction coefficients of the PTFE composites. However, the friction and wear properties of the ceramic particle filled PTFE composites can be greatly improved by lubrication with liquid paraffin, and the friction coefficients of the PTFE composites can be decreased by 1 order of magnitude. Under lubrication of liquid paraffin the friction coefficients of these ceramic particle filled PTFE composites decrease with an increase of load, but the wear of the PTFE composites increases with a load increase. The variations of the friction coefficients with load for these ceramic particle filled PTFE composites under lubrication of liquid paraffin can be properly described by the relationship between the friction coefficient (μ) and the simplified Sommerfeld variable N/P as given here. The investigations of the frictional surfaces show that the ceramic particles SiC, Si₃N₄, BN, and B₂O₃ enhance the adhesion of the transfer films of the PTFE composites to the surface of GCr15 bearing steel, so they greatly reduce the wear of the PTFE composites. However, the transfer of the PTFE composites onto the surface of the GCr15 bearing steel can be greatly reduced by lubrication with liquid paraffin, but the transfer still takes place. Meanwhile, the interactions between the liquid paraffin and the PTFE composites, especially the absorption of liquid paraffin into the surface layers of the PTFE composites, create some cracks on the worn surfaces of the ceramic particle filled PTFE composites; the creation and development of these cracks reduces the load-supporting capacity of the PTFE composites. This leads to the deterioration of the friction and wear properties of the PTFE composites under higher loads in liquid paraffin lubrication. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2611–2619, 1999     

Friction and wear characteristics of PTFE composites filled with metal oxides under lubrication by oil

Four kinds of polytetrafluoroethylene(PTFE)-based composites, such as pure PTFE, PTFE+30%(v)PbO, PTFE+30%(v)Pb₃O₄, and PTFE+30%(v)Cu₂O composite, were prepared. The friction and wear properties of these metal oxides filled PTFE composites sliding against GCr15 bearing steel in both dry and lubricated conditions were studied by using an MHK-500 ring-block wear tester. Then the worn surfaces of these PTFE composites and the transfer films of these PTFE composites formed on the surface of GCr15 bearing steel were examined by using a Scanning Electron Microscope (SEM) and an Optical Microscope, respectively. Experimental results show that the friction and wear properties of these metal oxide-filled PTFE composites can be greatly improved by liquid paraffin lubrication, and the friction coefficients can be decreased by one order of magnitude. Meanwhile, the interactions between liquid paraffin and metal oxide-filled PTFE composites, especially the absorption of liquid paraffin into the surface layers of these PTFE composites, reduce the mechanical strength and the load-carrying capacity of these metal oxide-filled PTFE composites. This leads to the deterioration of the friction and wear properties of these PTFE composites. Investigations of the frictional surfaces show that Pb₃O₄, Cu₂O, and PbO enhance the adhesion of the transfer films to the surface of GCr15-bearing steel, and thus promote the transfer of the PTFE composites onto the surface of GCr15-bearing steel. Therefore, they greatly reduce the wear of the PTFE composites. However, the transfer of these PTFE composites onto the counterfaces can be greatly reduced by lubrication with liquid paraffin. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 85–93, 1997     

Friction and wear characteristics of fiber- and whisker-reinforced PTFE composites under oil lubricated conditions

Four kinds of polytetrafluoroethylene (PTFE)-based composites, such as pure PTFE, PTFE + 30(vol.)% carbon fiber, PTFE + 30(vol.)% glass fiber, and PTFE + 30(vol.)% K₂Ti₆O₁₃ whisker composite, were prepared. The friction and wear properties of these fiber- and whisker-reinforced PTFE composites sliding against GCr15-bearing steel (SAE52100 steel) under both dry and liquid paraffin lubricated conditions were studied by using an MHK-500 ring-block wear tester (Timken wear tester). Then the worn surfaces of these PTFE composites and the transfer films formed on the surface of GCr15-bearing steel were investigated by using a Scanning Electron Microscope (SEM) and an Optical Microscope, respectively. Experimental results show that the friction and wear properties of the PTFE composites reinforced with carbon fiber, glass fiber, and a K₂Ti₆O₁₃ whisker can be greatly improved by lubrication with liquid paraffin, and the friction coefficients of these PTFE composites can be decreased by one order of magnitude compared to those under dry friction conditions. Meanwhile, the wear of the fiber- and whisker-reinforced PTFE composites in liquid paraffin lubrication increases with the increase of load, but the friction coefficients of these PTFE composites first decrease with the increase of load, and then increase with the increase of load. The variations of friction coefficients with load for these PTFE composites in liquid paraffin lubrication can be described properly by the Stribeck's curve as given in this article. However, when the load increases to the load limits of the PTFE composites, their friction and wear increase sharply. SEM and optical microscope investigations show that the interactions between liquid paraffin and the PTFE composites, especially the absorption of liquid paraffin into the surface layers of the PTFE composites, create some obvious cracks on the worn surfaces of the PTFE composites. The creation and the development of the cracks reduce the load-carrying capacity of the PTFE composites, and therefore lead to the increase of the friction and wear of the PTFE composites under higher loads. Meanwhile, the transfer of the fiber- and whisker-reinforced PTFE composites onto the counterfaces can be greatly reduced by lubrication with liquid paraffin, but the transfer still takes place. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1393–1402, 1998     

Friction and wear behavior of PTFE composites filled with rare earth compounds under oil‐lubricated conditions

Polytetrafluoroethylene (PTFE)‐based composites, filled with CeO₂, CeF₃, and La₂O₃ in volume contents of 5, 10, 15, 20, and 30%, were prepared. Then, the friction and wear behavior of these PTFE composites sliding against GCr15 bearing steel under both dry and liquid paraffin‐lubricated conditions was evaluated using an MHK‐500 ring‐on‐block wear tester. Finally, the worn surfaces and the transfer films of these PTFE composites were investigated using a scanning electron microscope (SEM) and an optical microscope. Experimental results showed that filling CeO₂, CeF₃, and La₂O₃ into PTFE can reduce the wear of the PTFE composites by 1–2 orders of magnitude. When the content of CeO₂ in PTFE is 15%, the friction and wear properties of the CeO₂‐filled PTFE composite are the best. Meanwhile, when the content of La₂O₃ in PTFE is between 15 and 20%, the PTFE composite filled with La₂O₃ exhibits excellent friction and wear‐reducing properties. However, the friction coefficient of the CeF₃‐filled PTFE composite increases but its wear decreases with increase in the content of CeF₃ from 5 to 30%. The friction and wear‐reducing properties of CeO₂‐, CeF₃‐, and La₂O₃‐filled PTFE composites can be greatly improved by lubrication with liquid paraffin, but the limit loads of the PTFE composites decrease with increase in the content of CeO₂, CeF₃, and La₂O₃ in PTFE (from 5 to 30%) under the same conditions. Investigations of worn surfaces show that the interaction between liquid paraffin and the CeO₂‐, CeF₃‐, and La₂O₃‐filled PTFE composites, especially the absorption of liquid paraffin into the microdefects of the PTFE composites, creates some cracks on the worn surfaces of the PTFE composites and that the creation and development of the cracks reduces the mechanical strength and the load‐supporting capacity of the PTFE composites. However, with increase of the content of CeO₂, CeF₃, and La₂O₃ in the PTFE, the microdefects in the PTFE composites also increase, which would lead to increase in the number of the cracks on the worn surfaces of the PTFE composites under load and, so, in turn, lead to the reduction of the limit loads of the CeO₂‐, CeF₃‐, and La₂O₃‐filled PTFE composites under lubrication with liquid paraffin. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 78: 797–805, 1999     

Friction and wear behavior of basalt‐fabric‐reinforced/solid‐lubricant‐filled phenolic composites

To improve the tribological properties of basalt‐fabric‐reinforced phenolic composites, solid lubricants of MoS₂ and graphite were incorporated, and the tribological properties of the resulting basalt‐fabric composites were investigated on a model ring‐on‐block test rig under dry sliding conditions. The effects of the filler content, load, and sliding time on the tribological behavior of the basalt‐fabric composites were systematically examined. The morphologies of the worn surfaces and transfer films formed on the counterpart steel rings were analyzed by means of scanning electron microscopy. The experimental results reveal that the incorporation of MoS₂ significantly decreased the friction coefficient, whereas the inclusion of graphite improved the wear resistance remarkably. The results also indicate that the filled basalt‐fabric composites seemed to be more suitable for friction materials serving under higher loads. The transfer films formed on the counterpart surfaces during the friction process made contributions to the reduction of the friction coefficient and wear rate of the basalt‐fabric composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Friction and wear properties of basalt fiber reinforced/solid lubricants filled polyimide composites under different sliding conditions

Short basalt fibers (BFs)‐reinforced polyimide (PI) composites filled with MoS₂ and graphite were fabricated by means of hot‐press molding technique. The tribological properties of the resulting composites sliding against GCr15 steel ring were investigated on a model ring‐on‐block test rig. The wear mechanisms were also comparatively discussed, based on scanning electron microscopic examination of the worn surface of the PI composites and the transfer film formed on the counterpart. Experimental results revealed that MoS₂ and graphite as fillers significantly improved the wear resistance of the BFs‐reinforced polyimide (BFs/PI) composites. For the best combination of friction coefficient and wear rate, the optimal volume content of MoS₂ and graphite in the composites appears to be 40 and 35%, respectively. It was also found that the tribological properties of the filled BFs/PI composites were closely related with the sliding conditions such as sliding speed and applied load. Research results show that the BF/PI composites exhibited better tribological properties under higher PV product. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Friction and wear behaviors of several polymers under oil-lubricated conditions

The friction and wear properties of polytetrafluoroethylene (PTFE), polyimide (PI), and polyamide 66 (PA66) sliding against GCr15 bearing steel under both dry and oil-lubricated conditions were studied by using an MHK-500 ring-block wear tester (Timken wear tester), and then Stribeck's curves of PTFE, PI, and PA66 under lubrication of the oil were given out. The worn surfaces of these polymers and the transfer films formed on the counterfaces were examined by using a scanning electron microscope (SEM) and an optical microscope, respectively. Experimental results show that the friction and wear-reducing properties of PTFE, PI, and PA66 can be greatly improved by lubrication with liquid paraffin, and the friction coefficients can be decreased by 1 order of magnitude compared to those in dry friction condition. Under lubrication of liquid paraffin, the friction coefficients of PTFE, PI, and PA66 decrease with the increase of load, but the wear increases with the increase of load. The variations of friction coefficients with load for PTFE, PI, and PA66 under lubrication of liquid paraffin can be described properly by the Stribeck's curves, as given out in this article. Under higher loads and sliding speeds in liquid paraffin lubrication, the friction and wear reducing properties of PA66 are the best, and those of PTFE are the worst; therefore, PA66 is also very suitable for applications in oil-lubricated conditions. Meanwhile, SEM and optical microscope investigations show that the wear and transfer of PTFE, PI, and PA66 can be greatly reduced by lubrication of liquid paraffin, but they still take place. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 2175–2182, 1998     

Effects of various kinds of fillers on the tribological behavior of polytetrafluoroethylene composites under dry and oil‐lubricated conditions

Polytetrafluoroethylene (PTFE)‐based composites filled with various inorganic fillers in a volume fraction of 30% were prepared. The tribological behavior of the PTFE composites sliding against AISI52100 steel under dry and liquid paraffin‐lubricated conditions was investigated on an MHK‐500 model ring‐on‐block test rig. The morphologies of worn surfaces and wear debris were observed with a scanning electron microscope (SEM) and an optical microscope. As the results, different fillers show different effects on the tribological behavior of the PTFE composites, while the composite shows much different tribological behavior under lubricated conditions as compared with dry sliding. The tribological behavior of the PTFE composites under dry sliding is greatly related to the uniformity and thickness of the transfer films. Only the PTFE composites with a transfer film of good uniformity and proper thickness may have excellent tribological behavior. The PTFE composites show much better tribological behavior under lubrication of liquid paraffin than under dry sliding, namely, the friction coefficients are decreased by 1 order of magnitude and the wear rate by 1–3 orders of magnitude. Observation of the worn composite surfaces with SEM indicates that fatigue cracks were generated under lubrication of liquid paraffin, owing to the absorption and osmosis of liquid paraffin into the microdefects of the PTFE composites. The creation and development of the fatigue cracks led to fatigue wear of the PTFE composites. This would reduce the mechanical strength and load‐supporting capacity of the PTFE composites. Therefore, the tribological behavior of the PTFE composites under lubrication of liquid paraffin is greatly dependent on the compatibility between the PTFE matrix and the inorganic fillers. In other words, the better is the compatibility between PTFE and fillers the better is the tribological behavior of the composites. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1891–1897, 2001     

An investigation of the friction and wear behaviors of polyphenylene sulfide filled with solid lubricants

Composites of polyphenylene sulfide (PPS) filled with solid lubricant particles of graphite (C), molybdenum disulfide (MoS₂), and polytetrafluoroethylene (PTFE) were prepared by compression molding. The size of the solid lubricant particles was 3‐;5 µm. The friction and wear behaviors of the composites were examined with a pinon‐disk test rig. The worn composite pin surfaces and the transfer films formed on the counterface were analyzed with scanning electron microscopy. An X‐ray photo‐electron spectroscope (XPS) was used to characterize the chemical states of the elements in the transfer film. It has been found that graphite and PTFE as the fillers increase the wear resistance of PPS considerably, while MoS₂ as the filler decreases the wear resistance of PPS greatly. The fillers promote the decomposition of PPS and generate compounds, which accounts for the changes in the wear resistance of the composites.     

Tribological behaviors of polytetrafluoroethylene composites under dry sliding and seawater lubrication

The composites of polytetrafluoroethylene (PTFE) filled with expanded graphite (EG), poly(p‐oxybenzoyl) (POB), and basalt fiber (BF) were prepared by heating compression and sintering molding. The tribological behavior of PTFE composites was investigated with a pin‐on‐disk tester under dry conditions and seawater lubrication. The worn surface of PTFE composites and the transfer film on the counterface were observed with a scanning electron microscope. The results indicated that the incorporation of EG and POB improved the hardness of PTFE composites, and addition of BF led to greater load‐carrying capacity. Compared to pure PTFE, the coefficients of friction of PTFE composites slightly increased, but the wear rates were significantly reduced (the wear rate of composite with 3% EG being only 10.38% of pure PTFE). In addition, all the composites exhibited a lower coefficient of friction (decreases of about 0.03–0.07) but more serious wear under seawater lubrication than under dry sliding. The wear mechanism changed from serious abrasive wear of pure PTFE to slight adhesion wear of PTFE composites under both conditions. A transfer film was obviously found on the counterface in seawater, but it was not observed under dry conditions. Among all the materials tested, the PTFE‐based composite containing 20% POB (mass fraction), 2% EG, and 3% BF exhibited the best comprehensive performance. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2523–2531, 2013     

Tribological properties of PTFE‐filled PMIA

The polytetrafluoroethylene‐filled (PTFE) poly(m‐phenylene isophalamide) (PMIA) composite blocks are prepared by compression molding. The friction and wear of PTFE‐filled PMIA are investigated on a block‐on‐ring machine by running the PMIA composite block against plain carbon steel (AISI 1045 steel ring). The worn surface of PMIA composite and the steel counterface are examined by using electron probe microanalysis (EPMA). It is found that PTFE‐filled PMIA exhibited considerably lower friction coefficient and wear rate than pure PMIA. Furthermore, the lowest wear rate is obtained when the composite contains 20 vol % PTFE. EPMA investigations show that there are some debris that could restrain the wear of the PMIA composites oriented along the sliding track and embedded in the surface of PMIA composite. A kind of stripe transfer film that contains abundant F element should be the main reason for the improvement of the tribological properties of PTFE‐filled PMIA composites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 747–751, 1999     

Influence of solid lubricant reinforcement on wear behavior of Kevlar fabric composites

The friction and wear behavior of Kevlar fabric composites reinforced by PTFE or graphite powders was investigated using a Xuanwu‐III friction and wear tester at dry sliding condition, with the unfilled Kevlar fabric composite as a reference. The worn surfaces were analyzed by means of scanning electron microscope, and X‐ray photoelectron spectroscopy. It was found that PTFE or graphite as fillers could significantly improve the tribological behavior of the Kevlar fabric composites, and the Kevlar fabric composites filled with 20% PTFE exhibited the best antiwear and antifriction ability among all evaluated cases. The transfer films established with two lubricants in sliding wear of composites against metallic counterparts made contributions to reducing friction coefficient and wear rate of Kevlar fabric composites. In particular, FeF₂ generated in the sliding of Kevlar fabric composites filled with PTFE against counterpart pin improved the bonding strength between the transfer film and counterpart surface, which accounted for the lowest friction coefficient and wear rate of the Kevlar fabric composites filled with PTFE measured in the testing. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Study on the tribological characteristics of solid lubricants embedded tin‐bronze bearings

The friction and wear characteristics of graphite, MoS₂, and PTFE embedded tin‐bronze bearings were studied using a pin‐on‐disc tester. The results indicated that solid lubricants decreased and stabilized the friction coefficient, and decreased the wear rate by two to three orders of magnitude. When the content of solid lubricants, PTFE mixed with graphite, was 20–40%, the performance of the solid lubricants embedded bearing (SLEB) was the best. Wear scar was analyzed by means of X‐ray diffraction (XRD), Auger electron spectroscopy (AES), and scanning electron microscopy (SEM). The results show that the transfer films of solid lubricants reduce adhesion between the SLEBs and the mating material, and the wear mechanism of SLEBs changes to fatigue and adhesive wear. The main reason for fatigue wear is microcracks expanding at Pb points in SLEBs. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2394–2399, 2001     

Tribological behavior of three‐dimensional braided carbon fiber reinforced polyetheretherketone composites

Three‐dimensional (3D) braided carbon fiber reinforced polyetheretherketone (denoted as CF_3D/PEEK) composites with various fiber volume fractions were prepared via hybrid woven plus vacuum heat‐pressing technology and their tribological behaviors against steel counterpart with different normal loads at dry sliding were investigated. Contrast tribological tests with different lubricants (deionized water and sea water) and counterparts made from different materials (epoxy resin, PEEK) were also conducted. The results showed that the incorporation of 3D braided carbon fiber can greatly improve the tribological properties of PEEK over a certain range of carbon fiber volume fraction (V_f) and an optimum fiber loading of ∼54% exists. The friction coefficient of the CF_3D/PEEK composites decreased from 0.195 to 0.173, while the specific wear rate increased from 1.48 × 10⁻⁷ to 1.78 × 10⁻⁷ mm³ Nm⁻¹ with the normal load increasing from 50 to 150 N. Abrasive mechanism was dominated when the composites sliding with GCr15 steel counterpart under dry and aqueous lubrication conditions. Deionized water and sea water lubricants both significantly reduced the wear of the CF_3D/PEEK composites. When sliding with neat PEEK counterpart, the CF_3D/PEEK composites possess lower friction coefficient than those against epoxy resin and GCr15 steel counterparts. In general, CF_3D/PEEK composites possess excellent tribological properties and comprehensive mechanical performance, which makes it become a potential candidate for special heat‐resisting tribological components. POLYM. COMPOS., 36:2174–2183, 2015. © 2014 Society of Plastics Engineers     

Study on the Friction and Wear Behaviors of Modified PA66 Composites

The wear-resistant polyamide 66 (PA66) composites were prepared and the mechanical properties, friction and wear properties were inspected. Results show that GF, PTFE and MoS₂ can improve the mechanical, friction and wear properties of PA66 composites. PTFE is more effective on the friction and wear properties than MoS₂ when GF is 30%wt. The best effect of the modification is 35%wt GF when both PTFE and MoS₂ were added. Friction coefficient first increase, then reduce to be stable as sliding time increases. Friction coefficient and wear mass loss increase as load increases. The main wear mechanisms are fatigue and abrasion wears.     

Effect of several solid lubricants on the mechanical and tribological properties of phenolic resin‐based composites

The flake graphite, polytetrafluoroethylene, and molybdenum disulfide (MoS₂) filled phenolic resin‐based composites were prepared by hot press molding. The thermal, mechanical, and tribological properties of composites were studied systematically. The morphologies of the worn surfaces and the change of chemical compositions during the sliding process of the composites were analyzed by scanning electron microscopy and X‐ray photoelectron spectroscopy, respectively. It was found that the heat‐resisting performance and the hardness of the composites are less affected by solid lubricants, while the solid lubricants did harm to the flexural strength of the composites. The friction and wear behaviors of composites highly depended on the volume fractions of solid lubricants and the sliding conditions. The wear resistance increases and the coefficient of friction decreases when the filler load increases. In addition, the appropriate content of solid lubricants is beneficial to reducing the sensitivities of the composites to load and sliding speed. POLYM. COMPOS., 36:2203–2211, 2015. © 2014 Society of Plastics Engineers     

Mechanical and tribological properties of polyoxymethylene modified with nanoparticles and solid lubricants

Polyoxymethylene (POM) composites modified with nanoparticles, polytetrafluoroethylene (PTFE) and MoS₂ were prepared by a twin‐screw extruder. The effect of nanoparticles and solid lubricant PTFE/MoS₂ on mechanical and tribological properties of the composites were studied. Tribological tests were conducted on an Amsler friction and wear tester using a block‐on‐ring arrangement under dry sliding and oil lubricated conditions, respectively. The results showed that generally speaking POM nanocomposites had better stiffness and tribological properties than corresponding POM composites attributed to the high surface energy of nanoparticles, except that the tensile strength of three composites and dry‐sliding tribological properties of POM/3%Al₂O₃ nanocomposite decreased due to the agglomeration of nanoparticles. Tribological properties differed under dry sliding and oil lubricated conditions. The friction coefficient and wear volume of POM nanocomposites under oil lubricated condition decreased significantly. The increased deformation resistance supported the increased wear resistance of POM nanocomposites. POM/PTFE/MoS₂/3%Al₂O₃ nanocomposite had the best mechanical and tribological properties of all three composites, which was attributed to the synergistic effect of nanoparticles and PTFE/MoS₂. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Enhanced tribological performance of hybrid polytetrafluoroethylene/Kevlar fabric composite filled with milled pitch‐based carbon fibers

As self‐lubricating bearing liner materials, tribological properties of milled pitch‐based carbon fibers (CFs) modified polytetrafluoroethylene (PTFE)/Kevlar fabric composites were investigated, and the microscopic morphology of worn surface was studied. The results show that the appropriate incorporation of CFs can obviously reduce the wear rate of the fabric composite with almost unchanging friction coefficient. The wear rates of 5 wt % CF‐filled PTFE/Kevlar fabric composites are decreased by 30% and 48% for two kinds of composites made with fibers from different producers compared with unfilled fabric composites. Scanning electron microscopy observations show that the appropriate incorporation of CFs obviously improves the interfacial bonding and reduces pull‐out and fracture of Kevlar fiber. Meanwhile, the introduction of CFs at proper fraction is helpful to form smooth and continuous transfer film on the surface of metal counterpart. The improving mechanism of the CF is attributed to increasing mechanical strength, thermal conductivity and self‐lubricating effects. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46269.