Reactions of 2-(4-morpholinothio)- and 2-(4-morpholinodithio)benzothiazole in the presence of polyisoprene

2-(4-Morpholinothio)benzothiazole (MOR) and 2-(4-morpholinodithio)-benzothiazole (MDB) were reacted, in combination with sulfur and ZnO, in the presence of polyisoprene (IR). Samples were heated in a DSC at 2.5°C/min and characterized by swelling experiments. The products formed at various temperatures were analyzed by HPLC. Crosslinking only occurred once all the benzothiazole sulfenamide had been consumed, the onset of vulcanization characterized by a considerable increase in 2-mercaptobenzothiazole (MBT) concentration. Crosslinking occurred earlier in all corresponding MDB formulations. Higher crosslink densities were recorded with addition of ZnO. The delayed action experienced in MOR systems was attributed to an exchange reaction between benzothiazole-terminated pendent groups and MOR and not due to the stability of the disulfide, MDB. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1093–1099, 1997     

The interaction of sulfenamide accelerators with sulfur,ZNO, and stearic acid in the absence of rubber

The interaction of sulfur, ZnO, stearic acid, and the three sulfenamide accelerators N-cyclohexylbenzothiazole sulfenamide (CBS), 2-(4-morpholinothio) benzothiazole (MOR), and 2-t-butylaminobenzothiazole sulfenamide (TBBS) were investigated by differential scanning calorimetry in the absence of rubber. In the presence of sulfur, the same product spectrum is formed as in its absence, but at lower temperatures. Thus, CBS gives N-cyclohexylamino-2-benzothiazole polysulfides (CBP), 2-bisbenzothiazole-2,2′-disulfide (MBTS), 2-bisbenzothiazole-2,2′-polysulfides (MBTP), and 2-bisbenzothiazole-2,2′-monosulfide (MBTP), 2-mercaptobenzothiazole (MBT), and 2-N-cyclohexylaminobenzothiazole (CB). In the presence of sulfur, the amount of polysulfides formed initially is higher but the polysulfides are unstable, and on prolonged heating, only MBT and CB remain. MOR and TBBS form analogous product spectra. The sulfenamides do not react with ZnO or zinc stearate. The MBT–amine complex prevents MBT, formed on decomposition, from reacting to give zinc mercaptobenzothiazole (ZHBT). Reaction mechanisms are proposed to account for the formation of the products. © 1994 John Wiley & Sons, Inc.     

Benzothiazole‐accelerated sulfur vulcanization. I. 2‐Mercaptobenzothiazole as accelerator for 2,3‐dimethyl‐2‐butene

2,3‐Dimethyl‐2‐butene (TME) was used as a model compound for polyisoprene in a study of 2‐mercaptobenzothiazole (MBT)‐accelerated sulfur vulcanization. Mixes that contained curatives only were heated in a DSC to various temperatures, while those that also contained TME were heated isothermally at 150°C in evacuated, sealed glass ampules. Heated mixtures were analyzed for residual curatives, intermediates, and reaction products by HPLC. It is proposed that MBT forms polysulfidic species (BtS_xH) in the presence of sulfur and that these react with TME via a concerted, substitutive reaction pathway to form polysulfidic hydrogen‐terminated pendent groups of varying sulfur rank (TME–S_xH). MBT is released as a by‐product of this reaction. Crosslinking occurs slowly as a result of the interaction of polythiol pendent groups, the rate being dependent on the pendent group concentration. H₂S is released on crosslinking. 2,3‐Dimethyl‐2‐butene–1‐thiol was synthesized and reacted in the presence of sulfur to confirm the formation of crosslinked products (TME–S_x–TME). Benzothiazole‐terminated pendent groups (TME–S_xBt) were not observed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1377–1385, 2000     

The thermal decomposition of sulfenamide accelerators

The thermal decomposition of three sulfenamide accelerators N-cyclohexylbenzothiazole sulfenamide (CBS), 2-(4-morpholinothio) benzothiazole (MOR) and 2-t-butylaminobenzothiazole sulfenamide (TBBS) were investigated by differential scanning calorimetry. The sulfenamides decompose rapidly at 210–220°C, yielding a number of products, including reactive polysulfidic complexes. Thus, CBS gives N-cyclohexylamino-2-benzothiazole polysulfides (CBP), 2-bisbenzothiazole-2,2′-disulfide (MBTS), 2-bisbenzothiazole-2,2′-polysulfides (MBTP), 2-bisbenzothiazole-2,2′-monosulfide (MBTM), 2-mercaptobenzothiazole (MBT), and 2-N-cyclohexylaminobenzothiazole (CB). The polysulfides are unstable, and on prolonged heating, only MBT and CB remain. The amine fragment of the accelerator is present as the amine salt of MBT. At lower temperatures, the sulfenamides are relatively stable. MOR forms an analogous product spectrum. The decomposition of TBBS is endothermic, in contrast to the exothermic reaction observed with CBS and MOR, and the concentrations of the various polysulfides do not decrease on prolonged heating. Reaction mechanisms are proposed to account for the formation of the products. © 1994 John Wiley & Sons, Inc.     

Synthesis,characterization and thermal degradation of poly[2‐(3‐p‐bromophenyl‐3‐methylcyclobutyl)‐2‐hydroxyethylmethacrylate]

In this work, 2‐(3‐p‐bromophenyl‐3‐methylcyclobutyl)‐2‐hydroxyethylmethacrylate (BPHEMA) [monomer] was synthesized by the addition of methacrylic acid to 1‐epoxyethyl‐3‐bromophenyl‐3‐methyl cyclobutane. The monomer and poly(BPHEMA) were characterized by FT‐IR and [¹H] and [¹³C]NMR. Average molecular weight, glass transition temperature, solubility parameter, and density of the polymer were also determined. Thermal degradation of poly[BPHEMA] was studied by thermogravimetry (TG), FT‐IR. Programmed heating was carried out at 10 °C min⁻¹ from room temperature to 500 °C. The partially degraded polymer was examined by FT‐IR spectroscopy. The degradation products were identified by using FT‐IR, [¹H] and [¹³C]NMR and GC‐MS techniques. Depolymerization is the main reaction in thermal degradation of the polymer up to about 300 °C. Percentage of the monomer in CRF (Cold Ring Fraction) was estimated at 33% in the peak area of the GC curve. Intramolecular cyclization and cyclic anhydride type structures were observed at temperatures above 300 °C. The liquid products of the degradation, formation of anhydride ring structures and mechanism of degradation are discussed. © 1999 Society of Chemical Industry     

Sulfur vulcanization of polyisoprene accelerated by benzothiazole derivatives. III. The reaction of 2-bisbenzothiazole-2,2′-disulfide with sulfur and ZnO in polyisoprene

The sulfur vulcanization of polyisoprene accelerated by 2-bisbenzothiazole-2,2′-disulfide (MBTS) was investigated. Rubber compounds were heated in a DSC and removed at various temperatures along the DSC thermal curve. The rubber vulcanizate was analyzed for crosslink density and for residual reactants and extractable reaction products. MBTS reacts readily with sulfur, and the polysulfidic accelerator complexes react with the rubber chain to form pendent groups. Crosslinking results from hydrogen abstraction, by the benzothiazole pendent group, from a neighboring chain. 2-Mercaptobenzothiazole, a product of crosslinking, also acts as an accelerator in the later stages of the reaction. MBTS has been shown not to react with ZnO and the higher crosslink densities obtained when ZnO is present are attributed to ZnO aiding the abstraction of the benzothiazole pendent group to give zinc mercaptobenzothiazole. A mechanism for the MBTS acceleration of sulfur vulcanization is proposed. © 1996 John Wiley & Sons, Inc.     

Preparation and properties of polyimides based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane

A series of polyimide (PI) thin films were synthesized based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane and conventional aromatic dianhydrides. The structures and properties of the thin films were measured with Fourier transform infrared, NMR, thermogravimetric analysis, dynamic mechanical analysis, and impedance analysis. The PI films exhibited glass‐transition temperatures in the range of 211–300°C and possessed initial thermal decomposition temperature reaching up to 457–482°C in air and 461–473°C in nitrogen. Some PI films had high solubility in organic solvents such as 1‐methyl‐2‐pyrrolidinone, N,N‐dimethylformamide, N,N‐dimethylacetamide, dimethyl sulfoxide, m‐cresol, tetrahydrofuran, and CHCl₃. The mechanical properties of these films were also examined. The dielectric constants of the films were in the range of 2.8–3.3 at 25°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1265–1270, 2007     

Crosslinking behavior of polyarylene ether nitrile terminated with phthalonitrile (PEN‐t‐Ph)/1,3,5‐Tri‐(3,4‐dicyanophenoxy) benzene (TPh) system and its enhanced thermal stability

A novel polyarylene ether nitrile terminated with phthalonitrile (PEN‐t‐Ph) was synthesized by a simple solution polycondensation of biphenyl and hydroquinone with 2,6‐dichlorobenzonitrile, followed by termination with 4‐nitrophthalonitrile. The PEN‐t‐Ph/1,3,5‐Tri‐(3,4‐dicyanophenoxy) benzene (TPh) system was prepared by cure treatment. The phthalonitrile on PEN‐t‐Ph were thermally crosslinked with TPh in the presence of diamino diphenyl sulfone through cure treatment up to 280–340°C, which led to the transformation from thermoplastic polymers to thermosetting polymers. This is because the phthalonitrile on the PEN‐t‐Ph can react with TPh by forming phthalocyanine ring. The glass transition temperatures of the PEN‐t‐Ph/TPh system increased from 152.4°C to 194.7°C, and the initial decomposition temperature (ranging from 475.3°C to 544.0°C) increased by 68°C after thermal curing. Therefore, their thermal properties can be greatly enhanced by crosslinking. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1363‐1368, 2013     

Synthesis of soluble and thermally stable polyimides from 3,5‐diamino‐N‐(4‐(8‐quinolinoxy) phenyl) aniline and various dianhydrides

Three novel polyimides (PIs) having pendent 4‐(quinolin‐8‐yloxy) aniline group were prepared by polycondensation of a new diamine with commercially available tetracarboxylic dianhydrides, such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs were characterized by FTIR, ¹H NMR, and elemental analysis; they had high yields with inherent viscosities in the range of 0.4–0.5 dl g⁻¹, and exhibited excellent solubility in many organic solvents such as N,N‐dimethyl acetamide, N,N′‐dimethyl formamide, N‐methyl pyrrolidone (NMP), dimethyl sulfoxide, and pyridine. These PIs exhibited glass transition temperatures (T_g) between 250 and 325° C. Their initial decomposition temperatures (T_i) ranged between 270 and 450°C, and 10% weight loss temperature (T₁₀) up to 500°C with 68% char yield at 600°C under nitrogen atmosphere. Transparent and hard polymer films were obtained via casting from their NMP solutions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of new cardo poly(ether imide)s derived from 9,9‐bis [4‐(4‐aminophenoxy)phenyl]xanthene

A series of new cardo poly(ether imide)s bearing flexible ether and bulky xanthene pendant groups was prepared from 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene with six commercially available aromatic tetracarboxylic dianhydrides in N,N‐dimethylacetamide (DMAc) via the poly(amic acid) precursors and subsequent thermal or chemical imidization. The intermediate poly(amic acid)s had inherent viscosities between 0.83 and 1.28 dL/g, could be cast from DMAc solutions and thermally converted into transparent, flexible, and tough poly(ether imide) films which were further characterized by X‐ray and mechanical analysis. All of the poly(ether imide)s were amorphous and their films exhibited tensile strengths of 89–108 MPa, elongations at break of 7–9%, and initial moduli of 2.12–2.65 GPa. Three poly(ether imide)s derived from 4,4′‐oxydiphthalic anhydride, 4,4′‐sulfonyldiphthalic anhydride, and 2,2‐bis(3,4‐dicarboxyphenyl))hexafluoropropane anhydride, respectively, exhibited excellent solubility in various solvents such as DMAc, N,N‐dimethylformamide, N‐methyl‐2‐pyrrolidinone, pyridine, and even in tetrahydrofuran at room temperature. The resulting poly(ether imide)s with glass transition temperatures between 286 and 335°C had initial decomposition temperatures above 500°C, 10% weight loss temperatures ranging from 551 to 575°C in nitrogen and 547 to 570°C in air, and char yields of 53–64% at 800°C in nitrogen. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A copolymer of poly[2,2′‐(m‐phenylene)‐5,5′‐ bibenzimidazole] and poly(2,5‐benzimidazole) for high‐temperature proton‐conducting membranes

A novel copolymer of polybenzimidazoles was prepared by copolymerization of 3,3′‐diaminobenzidine tetrahydrochloride, 3,4‐diaminobenzoic acid and isophthalic acid in polyphosphoric acid at 200 °C. The polymerization could be performed within 90–110 min with the assistance of microwave irradiation. The solubility of the copolymer obtained in N,N‐dimethylacetamide (DMAc) was improved compared with those of poly[2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole] and poly(2,5‐benzimidazole). Thus copolymer membranes could be readily prepared by dissolving the copolymer powders in DMAc with refluxing under ambient pressure. The decomposition temperature of the copolymer was about 520 °C in air according to thermogravimetric analysis data. The proton conductivity and mechanical strength of the phosphoric acid‐doped copolymer membranes were investigated at elevated temperatures. A conductivity of 0.09 S cm^?1 at 180 °C and a tensile stress at break of 5.9 MPa at 120 °C were achieved for the acid‐doped copolymer membranes by doping acids in a 75 wt% H₃PO₄ solution. Copyright © 2010 Society of Chemical Industry     

Synthesis and photopolymerization of 2‐(acryloyloxy)ethyl piperidine‐1‐carboxylate and 2‐(acryloyloxy)ethyl morpholone‐4‐carboxylate

Two low‐viscosity monomers, 2‐(acryloyloxy)ethyl piperidine‐1‐carboxylate (AEPC II) and 2‐(acryloyloxy)ethyl morpholone‐4‐carboxylate (AEMC), were synthesized with a non‐isocyanate route. The photopolymerization kinetics was monitored by real‐time infrared spectroscopy with a horizontal sample holder. The results indicated that AEPC II and AEMC had high ultraviolet curing rates and final double‐bond conversions, which could reach 90 and 95%, respectively. The glass‐transition temperatures of AEPC II/urethane acrylate resin (1/4 w/w), AEMC/urethane acrylate resin (1/4 w/w), and isobornyl acrylate/urethane acrylate resin (1/4 w/w) mixtures were 37.5, 45.6, and 57°C, respectively. The crosslink density of the AEMC/urethane acrylate resin (1/4 w/w) mixture was lower than that of the isobornyl acrylate/urethane acrylate resin (1/4 w/w) mixture. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of polyamides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan

A new diamine 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan ( 3 ) was prepared through the nucleophilic displacement of 5,5′‐bis(4‐hydroxylphenyl)‐hexahydro‐4,7‐methanoindan ( 1 ) with p‐halonitrobenzene in the presence of K₂CO₃ in N,N‐dimethylformamide (DMF), followed by catalytic reduction with hydrazine and Pd/C in ethanol. A series of new polyamides were synthesized by the direct polycondensation of diamine 3 with various aromatic dicarboxylic acids. The polymers were obtained in quantitative yields with inherent viscosities of 0.76–1.02 dl g⁻¹. All the polymers were soluble in aprotic dipolar solvents such as N,N‐dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidone (NMP), and could be solution cast into transparent, flexible and tough films. The glass transition temperatures of the polyamides were in the range 245–282 °C; their 10% weight loss temperatures were above 468 °C in nitrogen and above 465 °C in air. © 2000 Society of Chemical Industry     

High‐resolution thermogravimetry of poly(4‐methyl‐1‐pentene)

Thermal degradation and kinetics of poly(4‐methyl‐1‐pentene) were investigated by nonisothermal high‐resolution thermogravimetry at a variable heating rate. Thermal degradation temperatures are higher, but the maximum degradation rates are lower in nitrogen than in air. The degradation process in nitrogen is quite different from that in air. The average activation energy and frequency factor of the first stage of thermal degradation for the poly(4‐methyl‐1‐pentene) are 2.4 and 2.8 times greater in air than those in nitrogen, respectively. Poly(4‐methyl‐1‐pentene) exhibits almost the same decomposition order of 2.0 and char yield of 14.3–14.5 wt % above 500°C in nitrogen and air. The isothermal lifetime was estimated based on the kinetic parameters of nonisothermal degradation and compared with the isothermal lifetime observed experimentally. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2201–2207, 1999     

Organosoluble,low‐dielectric‐constant fluorinated polyimides based on 9,9‐bis[4‐(4‐amino‐2‐trifluoromethyl‐ phenoxy)phenyl]xanthene

A new trifluoromethylated bis(ether amine) monomer, 9,9‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]xanthene (BATFPX), was prepared through the nucleophilic aromatic substitution reaction of 2‐chloro‐5‐nitrobenzotrifluoride and 9,9‐bis(4‐hydroxyphenyl)xanthene in the presence of potassium carbonate, followed by catalytic reduction with hydrazine and Pd/C in ethanol. A series of novel fluorinated polyimides were synthesized from BATFPX with various commercially available aromatic tetracarboxylic dianhydrides by one‐step polycondensation in m‐cresol. The resulting polyimides were readily soluble in many organic solvents such as N,N‐dimethylacetamide and tetrahydrofuran, and afforded transparent, flexible and strong films with low moisture absorption (0.28–0.51%), low dielectric constant (2.85–3.26 at 1 MHz) and good optical transparency with UV‐visible absorption cut‐off wavelengths at 352–410 nm. All the polyimides were amorphous and exhibited high thermal stability, with glass transition temperatures of 282–330 °C, 5% weight loss temperatures above 520 °C in nitrogen or air and char yields higher than 55% at 800 °C in nitrogen. Also, these polyimides had good mechanical properties with tensile strengths of 93–118 MPa, elongations at break of 9–16% and initial moduli of 2.07–2.58 GPa. Copyright © 2011 Society of Chemical Industry     

Synthesis,characterization, and thermal degradation of novel poly(2‐(5‐bromo benzofuran‐2‐yl)‐2‐oxoethyl methacrylate)

A novel methacrylate monomer containing benzofuran side group, 2‐(5‐bromo benzofuran‐2‐yl)‐2‐oxoethyl methacrylate (BOEMA), was synthesized from esterification reaction of 2‐bromo‐1‐(5‐bromo benzofuran‐2‐yl) ethanone with sodium methacrylate at 85°C in the presence of 1,4‐dioxane solvent. After characterization with Fourier transform infrared spectrophotometer, nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR), its homopolymerization was carried out by free radical polymerization at 60°C in the presence of benzoyl peroxide initiator and 1,4‐dioxane solvent. The glass transition temperature (T_g) of the synthesized novel polymer, poly(2‐(5‐bromo benzofuran‐2‐yl)‐2‐oxoethyl methacrylate) [poly(BOEMA)], was determined to be 137°C with differential scanning calorimetry technique. Thermal degradation kinetics of poly(BOEMA) was investigated by thermogravimetric analysis method at different heating rates with 5°C/min intervals between measurements. From dynamic measurements, the analysis of each process mechanism of Coats–Redfern and Van Krevelen methods showed that the most probable model for the decomposition process of poly(BOEMA) homopolymer agrees with the random nucleation, F₁ mechanism. The apparent decomposition activation energies of poly(BOEMA) by Kissinger's and Flynn–Wall–Ozawa methods in the studied conversion range were 188.47 and 180.13 kJ/mol, respectively. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

The role of thiol intermediates in 2‐mercaptobenzothiazole accelerated sulfur vulcanization of rubber model compounds

The model compound, 2,3‐dimethyl‐2‐butene (TME), was vulcanized using 2‐mercaptobenzothiazole (MBT) and sulfur. MBT was not consumed during the vulcanization reaction. The resultant crosslink products were bis(alkenyl) in nature. 2,3‐Dimethyl‐2‐buten‐1‐thiol (TME‐SH) was identified as being present in the vulcanization mixture by a postcolumn derivatization technique. The appearance of thiol was coincident with crosslinking. Polysulfanes (H₂S_n) were formed on crosslinking. Studies of the reaction of TME‐SH and sulfur indicated a rapid reaction to form crosslink products and polysulfanes. No monosulfidic crosslink species were formed in these reactions. Closer investigation revealed the presence of small quantities of what appeared to be highly reactive polysulfidic thiols. This is the first time that such species have been identified in vulcanization systems. Consequently, MBT‐accelerated vulcanization of TME is proposed to occur via the reaction of MBT and S₈ to form polysulfidic MBT, which then reacts with TME to form polysulfidic thiols. These thiols then rapidly react via a metathesis reaction pathway to provide crosslink products and polysulfanes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 47–54, 2003     

Synthesis and characterization of melt‐processable polyimides derived from 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene

A series of molecular‐weight‐controlled imide resins end‐capped with phenylethynyl groups were prepared through the polycondensation of a mixture of 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene and 1,3‐bis(4‐aminophenoxy)benzene with 4,4′‐oxydiphthalic anhydride in the presence of 4‐phenylethynylphthalic anhydride as an end‐capping agent. The effects of the resin chemical structures and molecular weights on their melt processability and thermal properties were systematically investigated. The experimental results demonstrated that the molecular‐weight‐controlled imide resins exhibited not only meltability and melt stability but also low melt viscosity and high fluidability at temperatures lower than 280°C. The molecular‐weight‐controlled imide resins could be thermally cured at 371°C to yield thermoset polyimides by polymer chain extension and crosslinking. The neat thermoset polyimides showed excellent thermal stability, with an initial thermal decomposition temperature of more than 500°C and high glass‐transition temperatures greater than 290°C, and good mechanical properties, with flexural strengths in the range of 140.1–163.6 MPa, flexural moduli of 3.0–3.6 GPa, tensile strengths of 60.7–93.8 MPa, and elongations at break as high as 14.7%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis and characterization of novel polyimides derived from 2‐amino‐5‐(4‐aminophenyl)‐thiazole

A new kind of aromatic unsymmetrical diamine monomer containing thiazole ring, 2‐amino‐5‐(4‐aminophenyl)‐thiazole (AAPT), was synthesized. A series of novel polyimides were prepared by polycondensation of AAPT with various aromatic dianhydrides by one‐step polyimidation process. The synthesized polyimides had inherent viscosity values of 0.36–0.69 dL/g and were easily dissolved in highly dipolar solvents. Meanwhile, strong and flexible polyimide films were obtained, which have good thermal and thermo‐oxidative stability with the glass transition temperatures (T_g) of 276.7–346.1°C, the temperature at 5% weight loss of 451–492°C in nitrogen and 422–440°C in air, as well as have outstanding mechanical properties with the tensile strengths of 94–122 MPa, elongations at breakage of 5–18%. These films also had dielectric constants of 3.12–3.38 at 10 MHz. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Metal adhesive properties of polyamides having the 2,3‐bis(1,4‐phenylene)quinoxalinediyl structure

Polyamides were synthesized by interfacial polycondensation of 2,3‐bis(4‐chloroformylphenyl)quinoxaline (BCFPQ) and several aliphatic diamines using a phase transfer catalyst, and their adhesive property for stainless steel was investigated. The inherent viscosity of the obtained polyamides ranged from 0.37 to 1.24 dL g⁻¹. The glass transition temperatures of the polyamides ranged between 154 and 201°C, and their thermal decomposition temperatures were above 450°C. The polyamides were soluble in several organic solvents, including m‐cresol, N‐methyl‐2‐pyrrolidone (NMP), and formic acid. The adhesive property for stainless steel was examined by a standard tensile test. One member of the series, polyamide P8, derived from BCFPQ and 1,8‐octanediamine, displayed high tensile strength with values of 232 kgf cm⁻² at 20°C, 173 kgf cm⁻² at 120°C, and 137 kgf cm⁻² at 180°C. Thus, the tensile strength of P8 decreased at 180°C, but the decrease was much smaller than that of an epoxy resin in wide use as a metal adhesive. Heat distortion temperature, measured by thermal mechanical analysis, of P8 was 191°C. This suggested that P8 possessed high thermal resistance in metal adhesives. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1366–1370, 1999