Preparation,structure, and transport properties of ultrafiltration membranes of poly(vinyl chloride) and poly(vinyl pyrrolidone) blends

Ultrafiltration (UF) membranes based on poly(vinyl chloride) and poly(vinyl pyrrolidone) blends were prepared by the phase inversion method, and the factors governing membrane properties were investigated. The membranes were characterized by scanning electron microscopy and atomic force microscopy. The fouling characteristics of the membranes were determined by UF of aqueous solutions of bovine serum albumin (BSA) over a pH range of 2–9 and varying salt concentrations. The maximum adsorption of the protein on the membrane surface occurred near the isoelectric point (pI 4.8) of BSA, and the presence of the salts increased the fouling of the membrane. The results can be explained in terms of the nature of the membrane polymer and the effect of different ionic environments on the permeability of the deposited protein layer. The net charge on the BSA molecules appears to be a dominant factor in determining the flux of water through the blend membranes. The UF flux is correlated by a model based on the membrane resistance, adsorbed protein resistance, and time dependent resistance of the concentration polarization layer near the membrane surface. The ζ potentials of the membranes were also determined before and after UF to characterize the surface potential of the membrane. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2606–2620, 2000     

Preparation of chlorinated poly(vinyl chloride)‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membranes and their water permeation properties

Chlorinated poly(vinyl chloride) (CPVC) membranes for microfiltration processes were prepared with the combined process of a solvent evaporation technique and the water‐vapor induced‐phase‐inversion method. CPVC membranes with a mean pore size of 0.7 μm were very hydrophobic. These membranes were subjected to surface modification by ultraviolet (UV)‐assisted graft polymerization with N‐vinyl‐2‐pyrrolidinone (NVP) to increase their surface wettability and decrease their adsorptive fouling. The grafting yields of the modified membranes were controlled by alteration of UV irradiation time and NVP monomer concentration. The changes in chemical structure between the CPVC membrane and the CPVC‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membrane and the variation of the topologies of the modified PVC membranes were characterized by Fourier transform infrared spectroscopy, gel permeation chromatography, and field emission scanning electron microscopy. According to the results, the graft yield of the modified CPVC membrane reached a maximum at 5 min of UV exposure time and 20 vol % NVP concentration. The filtration behavior of these membranes was investigated with deionized water by a crossflow filtration measurement. The surface hydrophilicity and roughness were easily changed by the grafting of NVP on the surface of the CPVC membrane through a simultaneous irradiation grafting method by UV irradiation. To confirm the effect of grafting for filtration, we compared the unmodified and modified CPVC membranes with respect to their deionized water permeation by using crossflow filtration methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3188–3195, 2003     

Preparation of poly(vinyl chloride) (PVC) ultrafiltration membranes from PVC/additive/solvent and application of UF membranes as substrate for fabrication of reverse osmosis membranes

Ultrafiltration (UF) membranes were prepared from poly(vinyl chloride) (PVC) as main polymer, poly(vinyl pyrrolidone) (PVP) as additive, and 1‐methyl‐2‐pyrrolidone (NMP) as solvent using Design Expert software for designing the experiments. The membranes were characterized by SEM, contact angle measurement, and atomic force microscopy. The performance of UF membranes was evaluated by pure water flux (PWF) and blue indigo dye particle rejection. In addition, the molecular weight cutoff of UF membranes was determined by poly(ethylene glycol) (PEG) rejection. The UF membranes were used as substrates for fabrication of polyamide thin film composite (TFC) reverse osmosis (RO) membranes. The results showed that the model had high reliability for prediction of PWF of UF membranes. Also, increment in PVC concentration caused reduction of PWF. Moreover, at constant PVC concentration and if the concentrations of PVC was lower than 10 wt %, the PWF reduced by increasing the concentration of PVP. However, at PVC concentration higher than 11 wt %, increment in PVP concentration showed increment and reduction of PWF. The PEG rejection results showed that the prepared membranes had UF membranes properties. Finally, the NaCl rejection tests of RO membranes by PVC as substrates indicated that the performance of RO membranes were lower than commercial membranes. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46267.     

Poly(vinyl chloride) hollow‐fiber membranes for ultrafiltration applications: Effects of the internal coagulant composition

Poly(vinyl chloride) (PVC) hollow‐fiber membranes were spun by a dry/wet phase‐inversion technique from dopes containing 15 wt % PVC to achieve membranes with different pore sizes for ultrafiltration (UF) applications. The effects of the N,N‐dimethylacetamide (DMAc) concentration in the internal coagulant on the structural morphology, separation performance, and mechanical properties of the produced PVC hollow fibers were investigated. The PVC membranes were characterized by scanning electron microscopy, average pore size, pore size distribution, void volume fraction measurements, and solubility parameter difference. Moreover, the UF experiments were conducted with pure water and aqueous solutions of poly(vinyl pyrrolidone) as feeds. The mechanical properties of the PVC hollow‐fiber membranes were discussed in terms of the tensile strength and Young's modulus. It was found that the PVC membrane morphology changed from thin, fingerlike macrovoids at the inner edge to fully spongelike structure with DMAc concentration in the internal coagulant. The effective pores showed a wide distribution, between 0.2 and 1.1 μm, for the membranes prepared with H₂O as the internal coagulant and a narrow distribution, between 0.114 and 0.135 μm, with 50 wt % DMAc. The results illustrate that the difference in the membrane performances was dependent on the DMAc concentration. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of poly(vinyl chloride)‐graft‐acrylic acid membrane by electron beam

Poly(vinyl chloride) (PVC) was irradiated by electron beam in vacuum at 20 KGy to produce living free radicals, and then reacted with acrylic acid (AA) in solution to obtain the PVC‐g‐AA copolymers. The copolymers were characterized by Fourier transform infrared spectroscopy. Porous membranes were prepared from copolymers by the phase inversion technique. The morphology of PVC‐g‐AA membranes was studied by field emission scanning electron microscopy. The mean pore size and pore size distribution were determined by a mercury porosimeter. The mean pore size was 0.19 μm, and the bulk porosity was 56.02%. The apparent static water contact angle was 89.0°. The water drop penetration rate was 2.35 times to the original membrane. The maximum stress was 4.10 MPa. Filtration experiments were carried out to evaluate the fouling resistance of the PVC‐g‐AA membrane. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Improving the antifouling property of poly(vinyl chloride) membranes by poly(vinyl chloride)‐g‐poly(methacrylic acid) as the additive

To improve the antifouling property of poly(vinyl chloride) (PVC) membranes, a series of poly(methacrylic acid) grafted PVC copolymers (PVC‐g‐PMAA) with different grafting degree were synthesized via one‐step atom transfer radical polymerization process utilizing the labile chlorines on PVC backbones followed by one‐step hydrolysis reaction. PVC/PVC‐g‐PMAA blend membranes with different grafting degree and copolymer content were prepared by nonsolvent induced phase separation method. The surface chemical composition, surface charge, membrane structures, wettability, permeability, separation performances and the fouling resistance of blend membranes were carefully investigated. The results indicated that the PMAA chains were segregated towards the surface and the membranes were endowed with negative charge. The hydrophilicity and permeability of the blend membranes were obviously improved. Furthermore, the antifouling ability especially at neutral or alkaline environments was also significantly increased. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42745.     

Behavior of flexible poly(vinyl chloride)/poly(hydroxybutyrate valerate) blends

Blends of flexible poly(vinyl chloride) (PVC) and a poly(hydroxybutyrate valerate) (PHBV) copolymer were prepared and characterized with different techniques. The tensile strength of PVC did not show a marked reduction at PHBV concentrations up to 50 phr, despite a lack of miscibility between the two polymers. The crystallization of the PHBV copolymer was markedly hindered by the presence of PVC, as calorimetric results revealed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Blends of plasticized poly(vinyl chloride) and waste flexible poly(vinyl chloride) with waste nitrile rubber powder

Blends of poly(vinyl chloride) (PVC) with varying contents of plasticizer and finely ground powder of waste nitrile rubber rollers were prepared over a wide range of rubber contents through high‐temperature blending. The effects of rubber and plasticizer (dioctyl phthalate) content on the tensile strength, percentage elongation, impact properties, hardness, abrasion resistance, flexural crack resistance, limiting oxygen index (LOI), electrical properties, and breakdown voltage were studied. The percentage elongation, flexural crack resistance, and impact strength of blends increased considerably over those of PVC. The waste rubber had a plasticizing effect. Blends of waste plasticized PVC and waste nitrile rubber showed promising properties. The electrical properties and LOI decreased with increasing rubber and plasticizer content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1552–1558, 2004     

Preparation and structural characterization of nanocrystalline poly(vinyl chloride)

This article describes the development of novel nanocrystalline poly(vinyl chloride) (PVC) for potential applications in PVC processes and reports improvements in the mechanical properties and thermal resistance. Before the preparation of nanocrystalline PVC via jet milling, PVC was spray‐treated and heat‐treated to improve its crystallinity. The pulverization and degradation, morphology, crystalline structure, and melting‐point changes of postmodified PVC during jet milling and the relationship between the distributions of the particle size and processing temperature were investigated. X‐ray analysis and density testing indicated increased density and improved crystallinity. The crystalline region of nanocrystalline PVC was less than 80 nm, with a particle size distribution of 5–20 μm and a melting point of less than 128°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 563–569, 2004     

Effect of poly(vinyl chloride) resin type in the preparation process of slush powder

During the preparation of the poly(vinyl chloride) (PVC) slush powder, we found that PVC resins obtained by different polymerization methods affected many properties of slush powder and its products. Two types of commercial PVC resins were used for slush powder preparation: mass poly(vinyl chloride) (M‐PVC) and suspension poly(vinyl chloride) (S‐PVC). We used the Haake rheomix test to characterize the absorption of plasticizers into PVC resins, and the results showed that M‐PVC absorbed the plasticizers more quickly than S‐PVC. The fusion behavior of the two slush powders was studied by the thermal plate test and Haake rheomix test, and the results showed that the slush powder of M‐PVC was easier to fuse than that of S‐PVC. The different properties of the two resins and slush powder could be explained by the morphology, average size, and size distribution. Due to the “skin” of the particles' surfaces, the wider size distribution, and the large size of particles, S‐PVC absorbed the plasticizers more slowly and was more difficult to fuse. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3331–3335, 2002     

Soiling of plasticized poly(vinyl chloride)

The effects of three plasticizers and two plasticizer concentrations on the topography and soiling of poly (vinyl chloride) (PVC) were studied. Palmitic acid and triolein were chosen to represent solid and liquid soils. The feasibility of using infrared spectroscopy to quantify the amount of soil on PVC was examined. The structure of the solid model soil on plasticized PVC was studied with optical microscopy and atomic force microscopy. Palmitic acid formed two different structures on the PVC surface. Both the type and concentration of the plasticizer influenced the structure of the oily soil on plasticized PVC. The wetting of plasticized PVC with the liquid oily soil was compared to wetting with water through the measurement of the contact angles. Plasticized PVC was hydrophobic and oleophilic. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Chemical recycling of poly(vinyl chloride): Application of partially dehydrochlorinated poly(vinyl chloride) for producing a chemically modified polymer

Poly(vinyl chloride) (PVC) pipes were chemically modified to produce a sulfonated polymer with dehydrochlorinated PVC samples as intermediates. Two intermediates were formed: (1) partially dehydrochlorinated PVC with long sequences of conjugated double bonds and (2) the product of the partial dehydrochlorination of PVC and the nucleophilic substitution of chlorine by hydroxyl groups. The IR spectra showed that the dehydrochlorinated samples were heterogeneous materials, showing different proportions of elimination products, hydroxyl substitution, and partial oxidation. Samples dehydrochlorinated with poly(ethylene glycol) with a molecular weight of 400 g/mol for 24 h and 15 min showed the highest sulfonation yield, which was related to the sulfonation mechanism occurring predominantly because of the presence of hydroxyl groups in a mixture of vinyl alcohol and vinyl chloride units. The sulfonation was confirmed by the presence of a medium‐intensity band at 1180 cm^?1, assigned to sulfonic groups. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Surface treatment of plasticized poly(vinyl chloride) to prevent plasticizer migration

In this investigation, plasticized poly(vinyl chloride) (PVC) was treated with poly(azido acrylate)s to prevent plasticizer migration. This was achieved by modification of PVC sheets with poly(azido acrylate)s in a dichloromethane solution followed by irradiation under UV light. The surface‐modified PVC sheets with poly (azido acrylate)s were characterized with Fourier transform infrared spectroscopy and scanning electron microscopy analyses. The migration of the plasticizer was prevented to a large extent from modified PVC in comparison with unmodified PVC. The amount of plasticizer migration with respect to the irradiation time, incubation time, and number of dipping times was evaluated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation of microporous chlorinated poly(vinyl chloride) membrane in fabric and the characterization of their pore sizes and pore‐size distributions

Chlorinated poly(vinyl chloride) (CPVC)/poly(vinyl pyrrolidone) (PVP) membranes were prepared by using the solvent system tetrahydrofuran (THF)/n‐butyl alcohol (n‐BA) to investigate the possibility of pore size and pore‐size distribution control. The coagulation of CPVC/PVP solution was induced by the exposure to water vapor at 25 (±0.5)°C. The average pore diameter, d_p, and the size distribution of pores on the surface of the membrane were quantified through the image analyzer from the images visualized by field emission scanning electron microscope (FE‐SEM). Surface pore size and distribution of the prepared CPVC/PVP membrane were strongly affected by the relative humidity (RH) in the environment and the content of PVP used as an additive. Particularly, in the case of CPVC membrane without PVP, the mean pore size was 0.15–0.2 μm, depending on the RH. The pore distribution became broad with the increase of the RH. The membranes had open pores as confirmed by the hydraulic permeation experiment. In addition, the water flux and membrane resistance (R_m) were greatly affected by the composition of polymer solution and the RH. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1195–1202, 2002     

Miscibility of segmented polyurethane/poly(vinyl chloride) blends

Miscibilities of segmented polyurethanes (SPUs) and poly(vinyl chloride) (PVC) or functionalized poly(vinyl chloride) (FPVC) were studied with dynamic mechanical analysis, differential scanning calorimetry, and X‐ray diffraction. Mechanical properties of the blends were also studied with tensile measurements. The miscibility of the blends depended greatly on the hard‐segment content of SPU and the existence of the functional groups. The combination of SPU with a low hard‐segment content and PVC with functional groups made the blend system miscible. Moreover, controlling the blend composition of SPU/FPVC allowed us to modify the mechanical properties of SPU, where the elongation at break was multiplied without a significant change in its tensile strength. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3022–3029, 2001     

Surface modification of poly(vinyl chloride) for antithrombogenicity study

A process was established to conduct heparinization on the surface of poly(vinyl chloride) for antithrombogenicity utilization. A bifunctional monomer, glycidyl methacrylate (GMA), was grafted onto the surface of PVC by gas‐phase photografting polymerization without degassing first; then heparin was immobilized onto the poly(glycidyl methacrylate) segments. The branch structure of GMA and heparin were characterized by Fourier transfer infrared (FTIR) spectroscopy and electron spectroscopy (ESCA). It was confirmed that the bifunctional monomer GMA and heparin were grafted successfully onto the surface of PVC. The antithrombogenicity of the samples was tested both in vitro and in vivo, respectively. Results indicated that the blood compatibility of those products was improved greatly. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1013–1018, 2002     

Studies of polyester/chlorinated poly(vinyl chloride) blends

Chlorinated poly(vinyl chloride) (CPVC) was solution blended with poly(caprolactone) (PCL), poly(hexamethylene sebacate) (PHMS), poly(α-methyl-α-n-propyl-β-propiolactone) (PMPPL), poly(valerolactone) (PVL), poly(ethylene adipate), poly(ethylene succinate) and poly(β-propiolactone). From calorimetric glass transition temperature (T_g) measurements, it is concluded that CPVC is miscible with polyesters having a CH₂/COO ratio larger than three (PCL, PHMS, PMPPL and PVL). The Gordon-Taylor k parameter was also calculated and found equal to 1.0 and 0.56 for PCL/CPVC and PHMS/CPVC blends, respectively. From these values, it is concluded that CPVC gives a stronger interaction with polyesters than poly(vinyl chloride) due to its larger chlorine content.     

马来酸酐接枝改性氯化聚氯乙烯的制备及其在PVC中的应用

采用固相法制备马来酸酐接枝氯化聚氯乙烯(CPVC-g-MAH),得到了接枝率达2.91 %的CPVC-g-MAH,并对其进行了性能测试,探讨了聚氯乙烯(PVC)/CPVC-g-MAH共混物的冲击性能和加工性能,与PVC/氯化聚氯乙烯(CPVC)共混物进行对比以观察改性效果。结果表明,CPVC-g-MAH的热性能较CPVC有较大提高;PVC/CPVC-g-MAH共混物的冲击性能比PVC/CPVC共混物有所提高,而平衡转矩有所降低,说明CPVC-g-MAH相比于CPVC对PVC共混物加工性能改善效果更加明显。     

Absorption of trioctyl trimellitate into mass‐polymerization and suspension‐polymerization poly(vinyl chloride)

Poly(vinyl chloride) (PVC) slush powder has been widely used; we prepared it by dry blending. We found that the absorption of plasticizer by the PVC resins was the most important factor in the dry‐blending process and, further, that different types of PVC resin had different absorption rates. This results of this study provide new information about the relationship of absorption to PVC and other parameters. Haake rheomix testing and the quantity of plasticizers absorbed by the PVC resins were used to characterize the absorption process. Suspension‐polymerization poly(vinyl chloride) (SPVC) and mass‐polymerization poly(vinyl chloride) (MPVC) in different sizes were used for the test. The results showed that the MPVC absorbed the plasticizer more quickly than SPVC, especially at a higher temperature. However, for the same PVC resin type, the absorbing speeds were nearly independent of particle size. The studies that used a scanning electric microscope and specific surface area revealed that the morphology of the two types of particles was different. The surfaces of the individual particles of SPVC were smoother than those of MPVC. There was a “skin” covering the SPVC particles, whereas with the MPVC particles, the primary polymer was exposed directly on the surface. This difference in morphology was shown to be a significant factor in the different rates of absorption of the plasticizers for the different PVC resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2369–2374, 2004     

Networks of photocrosslinked poly(meth)acrylates in linear poly(vinyl chloride)

Five different multifunctional acrylic monomers (trimethylolpropane triacrylate, trimethylolpropane trimethacrylate, pentaerythritol triacrylate, pentaerythritol tetraacrylate, and dipentaerythritol pentaacrylate) were photopolymerized alone or in a matrix of linear poly(vinyl chloride) (PVC) with 2,2‐dimethyl‐2‐hydroxyacetophenone as a photoinitiator. The course of photopolymerization was estimated with Fourier transform infrared spectroscopy. The amount of insoluble gel formed during photopolymerization was determined gravimetrically. The crosslinked polymerization of pure monomers was much faster than that in the presence of PVC. However, the efficiency of the reaction was higher when it was carried out in a PVC blend because of the higher mobility of the propagating macroradicals. The influence of the monomer structure and functionality on the polymerization course was examined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3725–3734, 2002