Evaluation of melamine‐modified urea‐formaldehyde resins as particleboard binders

Particleboards bonded with 6 and 12% melamine‐modified urea‐formaldehyde (UMF) resins were manufactured using two different press temperatures and press times and the mechanical properties, water resistance, and formaldehyde emission (FE) values of boards were measured in comparison to a typical urea‐formaldehyde (UF) resin as control. The formaldehyde/(urea + melamine) (F/(U + M)) mole ratio of UMF resins and F/U mole ratio of UF resins were 1.05, 1.15, and 1.25 that encompass the current industrial values near 1.15. UMF resins exhibited better physical properties, higher water resistance, and lower FE values of boards than UF resin control for all F/(U + M) mole ratios tested. Therefore, addition of melamine at these levels can provide lower FE and maintain the physical properties of boards. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A study on the colloidal nature of urea‐formaldehyde resins and its relation with adhesive performance

Urea‐formaldehyde (UF) resins present a swollen colloidal phase dispersed within a continuous water phase containing soluble oligomers. The main goal of the present investigation is to clarify the physical and chemical nature of those two phases and elucidate their impact on the bonding process. Optical and electronic microscopy has provided information on the morphology of the colloidal phase, showing primary particles and particle agglomerates. Mechanisms are suggested for the colloidal stabilization and dilution‐induced flocculation. Three commercial UF resins with different F/U molar ratios were studied using particle size distribution (PSD) analysis. The results showed the influence of the resin's degree of condensation and the aging status on the size of the colloidal structures. Gel permeation chromatography analysis was performed on samples of different resins and of the respective continuous and dispersed phases, separated by centrifugation. The quantified fraction of insoluble molecular aggregates present in the chromatograms was related to the resins synthesis conditions and age. Differential scanning calorimetry and tensile shear strength tests were performed to evaluate the reactivity and adhesive performance of each phase. It is suggested that the colloidal phase acts as a reactive filler at the wood joint interfaces, contributing for the resins bonding performance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Production of melamine fortified urea‐formaldehyde resins with low formaldehyde emission

Melamine can be incorporated in the synthesis of urea‐formaldehyde (UF) resins to improve performance in particleboards (PB), mostly in terms of hydrolysis resistance and formaldehyde emission. In this work, melamine‐fortified UF resins were synthesized using a strong acid process. The best step for melamine addition and the effect of the reaction pH on the resin characteristics and performance were evaluated. Results showed that melamine incorporation is more effective when added on the initial acidic stage. The condensation reaction pH has a significant effect on the synthesis process. A pH below 3.0 results on a very fast reaction that is difficult to control. On the other hand, with pH values above 5.0, the condensation reaction becomes excessively slow. PBs panels produced with resins synthesized with a condensation pH between 4.5 and 4.7 showed good overall performance, both in terms of internal bond strength and formaldehyde emissions. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Curing of low level melamine‐modified urea‐formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)

Effects of resin formulation, catalyst, and curing temperature were studied for particleboard binder‐type urea‐formaldehyde (UF) and 6 ～ 12% melamine‐modified urea‐melamine‐formaldehyde (UMF) resins using the dynamic mechanical analysis method at 125 ～ 160°C. In general, the UF and UMF resins gelled and, after a relatively long low modulus period, rapidly vitrified. The gel times shortened as the catalyst level and resin mix time increased. The cure slope of the vitrification stage decreased as the catalyst mix time increased, perhaps because of the deleterious effects of polymer advancements incurred before curing. For UMF resins, the higher extent of polymerization effected for UF base resin in resin synthesis increased the cure slope of vitrification. The cure times taken to reach the vitrification were longer for UMF resins than UF resins and increased with increased melamine levels. The thermal stability and rigidity of cured UMF resins were higher than those of UF resins and also higher for resins with higher melamine levels, to indicate the possibility of bonding particleboard with improved bond strength and lower formaldehyde emission. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 377–389, 2005     

13C‐NMR study on the structure of phenol‐urea‐formaldehyde resins prepared by methylolureas and phenol

Phenol‐urea‐formaldehyde (PUF) resins were synthesized by reacting mixture of methylolureas (MMU), phenol, and formaldehyde. The structure of PUF cocondensed resins at different stages of reaction were analyzed by liquid ¹³C nuclear magnetic resonance (NMR) spectroscopy. The liquid ¹³C‐NMR analysis indicated that methylolureas had the dominant content in MMU with the reaction between urea and formaldehyde under the alkaline condition. The PUF cocondensed resins had no free formaldehyde. methylolureas were well incorporated into the cocondensed resins by reacting with phenolic units to form cocondensed methylene bridges. The second formaldehyde influenced the further reaction and the structure of the PUF resins. The resins with the prepared method of PUFB possessed relatively high degree of polymerization and low proportion of unreacted methylol groups. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis,structure, and characterization of glyoxal‐urea‐formaldehyde cocondensed resins

To decrease the formaldehyde emission of urea‐formaldehyde (UF) bonded products at source, monomethylol urea (MMU) was chosen to react with glyoxal (G), a nonvolatile and nontoxic aldehyde, to prepare a novel glyoxal‐urea‐formaldehyde (GUF) cocondensed resin. The GUF resins were synthesized with different MMU/G molar ratios, and the basic properties were tested. The GUF resins were characterized by ultraviolet‐visible spectroscopy, Fourier transform infrared spectroscopy, carbon‐13 nuclear magnetic resonance spectroscopy and matrix assisted laser desorption ionization time of flight mass spectrometry (MALDI‐TOF‐MS). The results show that the synthesized GUF resins remain stable for at least 10 days at ambient temperature. Conjugated structures, and large amounts of ? OH, ? NH? , C? N, and C?O groups with different levels of substitution exist in the GUF resin. There are two repeating motives in the MALDI‐TOF‐MS spectrum of the GUF resin, one of 175 ±1 Da and a second one of 161 ± 1 Da. Moreover, the peaks due to the dehydration condensation reaction of MMU also appear in the spectra. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41009.     

Morphology and chemical elements detection of cured urea–formaldehyde resins

As a part of understanding the hydrolysis of cured urea–formaldehyde (UF) resins that has been known as responsible for the formaldehyde emission, leading to sick building syndrome, this study attempted to investigate the morphology and to detect chemical elements of the cured UF resins of different formaldehyde/urea (F/U) mole ratios and hardener (NH₄Cl) levels, using field emission‐scanning electron microscopy and energy‐dispersive spectroscopy. Cured UF resins of low F/U mole ratio showed spherical structure whose diameter increased with an increase in the hardener level, whereas this was not observed for high F/U mole ratio UF resins regardless of the hardener levels. The energy‐dispersive spectroscopy results showed five different chemical elements such as carbon, nitrogen, oxygen, chloride, and sodium in cured UF resins. The chloride distribution assumed as the presence of residual acid in the cured UF resins suggested that the hydrolysis of cured UF resins could initiate at the sites of chlorides on the surface of the spherical structures. As the hardener level increased, the quantities of both carbon and oxygen decreased, whereas those of nitrogen and chloride increased as expected. But the quantity of sodium was within measurement error. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Low‐volatility acetals to upgrade the performance of melamine–urea–formaldehyde wood adhesive resins

1,1,2,2‐Tetramethoxyethane (TME), a high boiling point acetal derived from glyoxol, lhas been shown to upgrade the performance of melamine‐urea‐formaldehyde (MUF) and some UF resins used for wood adhesives. This affords the possibility of decreasing the percentage of resin used in the preparation of wood panels without volatilizing the TME acetal used.     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. IV

Typical particleboard wood‐adhesive urea–formaldehyde (UF) resins, synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.80, 2.10, and 2.40 and the second urea added to an overall F/U ratio of 1.15, in weak alkaline pH, were allowed to stand at room temperature over a period of 50 days. ¹³C‐NMR of time samples taken over the storage period showed gradual migration of hydroxymethyl groups from the polymeric first‐urea components to the monomeric second‐urea components and also an advancing degree of polymerization of resins by forming methylene and methylene ether groups involving the second urea. These phenomena that varied with the F/U₁ mol ratios used in the resin syntheses due to the varying polymer branching structures resulted in the first step of resin synthesis. Varying viscosity decreases and increases of the resins also occurred. Due to these chemical and physical changes, the particleboards that bonded with the sampled resins showed varying bond strength and formaldehyde‐emission values, indicating process optimizations possible to improve bonding and formaldehyde‐emission performances. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1155–1169, 2001     

Hydrolytic stability of cured urea‐formaldehyde resins modified by additives

Urea‐formaldehyde (UF) resins are prone to hydrolysis that results in low‐moisture resistance and subsequent formaldehyde emission from UF resin‐bonded wood panels. This study was conducted to investigate hydrolytic stability of modified UF resins as a way of lowering the formaldehyde emission of cured UF resin. Neat UF resins with three different formaldehyde/urea (F/U) mole ratios (1.4, 1.2, and 1.0) were modified, after resin synthesis, by adding four additives such as sodium hydrosulfite, sodium bisulfite, acrylamide, and polymeric 4,4′‐diphenylmethane diisocyanate (pMDI). All additives were added to UF resins with three different F/U mole ratios before curing the resin. The hydrolytic stability of UF resins was determined by measuring the mass loss and liberated formaldehyde concentration of cured and modified UF resins after acid hydrolysis. Modified UF resins of lower F/U mole ratios of 1.0 and 1.2 showed better hydrolytic stability than the one of higher F/U mole ratio of 1.4, except the modified UF resins with pMDI. The hydrolytic stability of modified UF resins by sulfur compounds (sodium bisulfate and sodium hydrosulfite) decreased with an increase in their level. However, both acrylamide and pMDI were much more effective than two sulfur compounds in terms of hydrolytic stability of modified UF resins. These results indicated that modified UF resin of the F/U mole ratio of 1.2 by adding acrylamide was the most effective in improving the hydrolytic stability of UF resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Urea–formaldehyde–propionaldehyde physical gelation resins for improved swelling in water

Urea–formaldehyde (UF) resins' water tolerance and swelling thickness of interior‐grade wood panels bonded with UF resins were improved markedly by introducing small amounts of UFPropanal (UFP) polycondensates into the UF resin. ¹³C NMR of urea–propanal (UP) resins showed that urea and propanal do react up to the formation of dimers. The water repellancy imparted by insertion in the resin of the alkyl chain of propanal limits the proportion of propanal that can be used. Gel permeation chromatography showed that this appears to be so because UP resins and UFP resins exist as an equilibrium between two separate intermingling phases, namely one in solution and the second in a state of physical gelation. This latter is different from the state of physical gelation observed on ageing or advancement of formaldehyde‐only based polycondensation resins. This physical gelation is brought on by the insertion in the resin of the water repellant chain of the propanal reacted with urea and constitutes a new state of physical gelation of polycondensates other than what was already reported in the literature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5131–5136, 2006     

Fast advancement and hardening acceleration of low‐condensation alkaline PF resins by esters and copolymerized urea

Low‐condensation phenol‐formaldehyde (PF) resins coreacted under alkaline conditions with up to 42% molar urea on phenol during resin preparation yielded PUF resins capable of faster hardening times than equivalent pure PF resins prepared under identical conditions and presented better performance than the latter. The water resistance of the PUF resins prepared seemed comparable to pure PF resins when used as adhesives for wood particleboard. Part of the urea was found by ¹³C‐NMR to be copolymerized to yield the alkaline PUF resin; whereas, especially at the higher levels of urea addition, unreacted urea was still present in the resin. Increase of the initial formaldehyde to phenol molar ratio decreased considerably the proportion of unreacted urea and increased the proportion of PUF resin. A coreaction scheme of phenolic and aminoplastic methylol groups with reactive phenol and urea sites based on previous model compounds work has been proposed, copolymerized urea functioning as a prebranching molecule in the forming, hardened resin network. The PUF resins prepared were capable of further noticeable curing acceleration by addition of ester accelerators; namely, glycerol triacetate (triacetin), to reach gel times as fast as those characteristic of catalyzed aminoplastic resins, but at wet strength values characteristic of exterior PF resins. Synergy between the relative amounts of copolymerized urea and ester accelerator was very noticeable at the lower levels of the two parameters, but this effect decreased in intensity toward the higher percentages of urea and triacetin. ¹³C‐NMR assignements of the relevant peaks of the PUF resins are reported and compared with what has been reported in the literature for mixed, coreacted model compounds and pure PF and urea‐formaldehyde (UF) resins. The relative performance of the different PUF resins prepared was checked under different conditions by thermomechanical analysis (TMA) and by preparation of wood particleboard, and the capability of the accelerated PUF resins to achieve press times as fast as those of aminoplastic (UF and others) resins was confirmed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 359–378, 1999     

Syntheses and properties of low‐level melamine‐modified urea–melamine–formaldehyde resins

Syntheses of urea–melamine–formaldehyde (UMF) resins were studied using 2–12% melamine levels and UF base resins that were preadvanced to various different extents. The melamine reaction was carried out at pH 6.3 with F/(U + M) mole ratio of 2.1 until a target viscosity of V was reached (Gardener–Holdt) and then the second urea added at pH 8.0 to give a final F/(U + M) mole ratio of 1.15. Analyses with ¹³C‐NMR and viscosity measurements showed that MF components react fast and the UF components very slowly in the melamine reaction. Therefore, as the extent of preadvancement of UF base resin was decreased, the reaction time to reach the target viscosity became longer and the MF resin components showed high degrees of polymerization. The overpolymerization of MF components resulted in increasingly more opaque resins, with viscosity remaining stable for more than a month. As the preadvancement of UF base resin was increased, the extent of advancement of MF components decreased, to give clearer resins, with viscosity slowly increasing at room temperature. Overall, preadvancing the UF base resin components to an appropriate extent was found to be a key to synthesizing various low‐level melamine‐modified UMF resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2559–2569, 2004     

Influence of nanoclay on urea‐formaldehyde resins for wood adhesives and its model

The addition of small percentages of Na⁺‐montmorillonite (NaMMT) nanoclay appears to improve considerably the performance of thermosetting urea‐formaldehyde (UF) resins used as adhesives for plywood and for wood particleboard. X‐ray diffraction (XRD) studies indicated that NaMMT loses the periodic atomic structure when mixed in small proportions in the acid‐curing environment characteristic of the curing of UF resins. This can be interpreted as becoming exfoliated under such conditions. The partly crystalline structure of the ordered zones of the UF resins is maintained but at a slightly lower level. Differential scanning calorimetry (DSC) indicated that NaMMT has an accelerating effect on the curing of the UF resin. It also appears to lead to a more controlled rate of crosslinking implying a more regular hardened network. The influence of NaMMT addition was particularly noted in plywood by the increase in water resistance of the UF‐bonded panel. In the case of wood particleboard even the dry internal bond strength of the panel, a direct indication of the performance of the resin, improved with small additions of NaMMT. A hypothesis and model of the reasons why such improvement to the performance of UF resins by addition of nanoclay should occur has been presented. This is based on the application of percolation theory to the networking capability of the clay nanoplatelets. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A very simple empirical kinetic model of the acid‐catalyzed cure of urea–formaldehyde resins

The hot pressing operation is the final stage in MDF (medium density fiberboard) manufacture; the fiber mat is compressed and heated up to promote the cure of the resin. The aim of the investigations is to study the curing reactions of UF (Urea–Formaldehyde) resins as commonly used in the production of MDF, and to develop a simplified kinetic model. This investigation has combined Raman spectroscopy to study the reaction cure and ¹³C‐NMR for the quantitative and qualitative characterization of the liquid and still uncured resin. Raman spectroscopy was found very interesting for the study of the resin cure and permitted to obtain kinetic data as the basis for a simple empirical model, considering a homogeneous irreversible reaction of a single kind of methylol group and ureas with rate constants depending on their degree of substitution. Although these results can provide a better understanding of the composition and the cure of an UF resin, several issues remain open, such as the influence of the reversibility of the reactions taking place during the curing process as well as the possible formation of cyclic groups in the resin. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5977–5987, 2006     

Examination of selected synthesis parameters for wood adhesive‐type urea–formaldehyde resins by 13C NMR spectroscopy. III

The varying polymer structures of wood adhesive‐type urea–formaldehyde resins resulting from different formaldehyde/first urea (F/U₁) mole ratios used in the first step of resin manufacture were investigated using ¹³C. As the F/U₁ mole ratio decreased progressively from 2.40 to 2.10 and to 1.80, the viscosity increase due to polymerization during resin synthesis became faster and resulted in decreasing side‐chain branches and increasing free urea amide groups in the resin structure. The resultant UF resins, with the second urea added to an overall F/(U₁ + U₂) of 1.15, showed viscosity decreases when heated with stirring or allowed to stand at room temperature that were also characteristic with the F/U₁ mole ratios used in resin synthesis. The formaldehyde emission levels of particleboards bonded with the freshly made UF resins showed relatively small but similarly characteristic variations. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2800–2814, 2001     

Fibers from urea–formaldehyde resins

The preparation of fibers from aqueous urea–formaldehyde resins has been investigated; a dry spinning process has been developed based on the extrusion of catalyzed resin into a drying chamber at 180–220°C, producing a multifilament yarn at spinning speeds of up to 600 m/min. A range of UF filaments was produced with diameters between 10–70 μm; the tenacities of spun filaments were 6–10 cN/tex, initial moduli were 220–340 cN/tex, and elongation at break was 4–10%. The best tensile properties resulted from conditions that produced the smallest diameter fibers. Postspin heat treatment improved the tenacity to 14 cN/tex and the elongation to 20%. Spinnability improved with increased viscosity of the spinning solution and increased cell temperature, while tenacity and elongation increased with increasing cell temperature and spinning stretch. A correlation was found between TGA weight loss (between 105 and 200°C) and fiber tenacity. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 64–74, 2000     

Effect of addition of glycolysis products of poly(ethyleneterephthalate) wastes to urea‐formaldehyde resin on its adhesion performance to wood substrates and formaldehyde emission

Recycling of poly(ethyleneterephthalate) waste was achieved through glycolysis using diethyleneglycol (DEG) and poly(ethyleneglycol) (PEG 400), which yielded different fractions that exhibited hydroxyl numbers of 174.41 and 54.86 mg of KOH/g, respectively, whereas GPC profiles revealed bimodality in both cases corresponding to M_n values equivalent to 534 and 1648. The products of glycolysis from both cases were individually incorporated as modifiers during the synthesis of urea‐formaldehyde resins from both the basic as well as acidic stages, respectively. It was found that the free formaldehyde level was remarkably decreased for the modified resins while the gel time was slightly affected indicating some activation of the resins. In addition, the adhesion strength of wood joints bonded with the modified resins improved markedly in the dry state while the moisture resistance was significantly fortified with respect to the comparable joints formulated from unmodified resins where instant failure took place within few hours after immersion in water. The shelf life of the resins did not prolong and lasted maximum for about 2 months which was ascribed to the presence of reasonable amount of carboxyl terminal groups at the ends of a minor portion of the glycolyzed products that could actively act to self‐catalyze the polycondensation and crosslinking reactions during storage leading eventually to vitrification of the resin and shortening of shelf life. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Upgrading melamine–urea–formaldehyde polycondensation resins with buffering additives. I. The effect of hexamine sulfate and its limits

Iminoamino methylene base intermediates obtained by the decomposition of hexamethylenetetramine (hexamine) stabilized by the presence of strong anions such as SO and HSO, or hexamine sulfate, were shown to markedly improve the water and weather resistance of hardened melamine–urea–formaldehyde (MUF) resins used as wood adhesives and of the wet internal bond strength performance of wood boards bonded with them. The effect was shown to be induced by very small amounts, between 1 and 5 wt % of this material on resin solid content. This strong effect allowed the use of MUF resins of much lower melamine content and also provided good performance of the bonded joints. Because the main effect was also present at the smaller proportion of hexamine as hexamine sulfate, it was not due at all to any increase in the molar ratio of the resin as a consequence of hexamine sulfate addition. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 203–214, 2003     

Correlating viscosity in urea–formaldehyde polymerization

The objective of this study was to find a correlation for the viscosity changes during step polymerization of urea and formaldehyde. For this reason, a kinetic model for the condensation reactions was proposed, and using this model, a correlation for the kinematic viscosity changes of the solution during polymerization was obtained. Viscosity measurements of the samples during condensation reactions were carried out using Ubbelohde viscometers at intervals. The experimental data were curve fitted using our model, which was found to correspond very well. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 631–636, 1998