Comparison of properties of thermoplastic polyurethane elastomers with two different soft segments

Two series of thermoplastic polyurethane elastomers [poly(propylene glycol) (PPG) based PP samples and poly(oxytetramethylene)glycol (PTMG) based PT samples] were synthesized from isophorone diisocyanate (IPDI)/1,4-butanediol (BD)/PPG and IPDI/BD/PTMG. The IPDI/BD based hard segments contents of polyurethane prepared in this study were 40–73 wt %. These polyurethane elastomers had a constant soft segment molecular weight (average M_n, 2000) but a variable hard segment block length (n, 3.5–17.5; average M_n, 1318–5544). Studies were made on the effects of the hard segment content on the dynamic mechanical thermal properties and elastic behaviors of polyurethane elastomers. These properties of PPG based PP and PTMG based PT samples were compared. As the hard segment contents of PP and PT samples increased, dynamic tensile modulus and α-type glass transition temperature (T_g) increased; however, the β-type T_g decreased. The permanent set (%) increased with increasing hard segment content and successive maximum elongation. The permanent set of the PT sample was lower than that of the PP sample at the same hard segment content. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1349–1355, 1998     

Synthesis,characterisation, and chemical degradation of segmented polyurethanes with butylamine for chemical recycling

Polyurethane elastomers (PU) have been synthesized from polytetramethylene glycol 2000 (PTMG 2000); 4, 4′‐diphenylmethane diisocyanate (MDI) and 1, 4‐butanediol (BD) as chain extender. This synthesis has been done in two steps known as prepolymer methods. The concentration of soft segments and hydrogen attachment in the matrices, have been studied. The results show that the glass transition of the soft segment T_g(s) do not take any changes with the concentration of the soft segment in the matrices. Although, the glass transition temperature of the hard segment T_g(H) increases when the concentration of the hard segment increases in the matrices. In general, the properties of the polyurethane elastomers depend on the extenders nature, the synthesis methods, phase segregation etc. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Differential scanning calorimetry analysis of silicon‐containing and phosphorus‐containing segmented polyurethane. I—Thermal behaviors and morphology

This article investigated thermal transition and morphology utilizing differential scanning calorimetry (DSC), which was performed on silicon‐containing and phosphorus‐containing segmented polyurethane (Si‐PU and P‐PU). The hard segments of those Si‐PU and P‐PU polymers investigated consisted of 4,4′‐diphenylmethane diisocyanate (MDI) and diphenylsilanediol (DSiD), MDI, and methylphosponic (MPA), respectively. The soft segment of those polymers comprised polytetramethylene ether glycol, with an average molecular weight of 1000 or 2000 (PTMG 1000 and PTMG 2000, respectively). Several thermal transitions appeared for on the Si‐PU and P‐PU polymers, reflecting both the soft‐segment and hard‐segment phases. The Si‐PU and P‐PU polymers with a lower hard‐segment content exhibited a high degree of phase separating as indicated by the constancy of both the soft‐segment glass transition temperature (T_gs) and the breadth of transition zone (ΔB). The polymers in which PTMG 2000 was used as the soft segment generally exhibited a crystalline melting endotherm about 10°C, while crystallization usually disappeared upon melt quenching. The hard segments of the Si‐PU and P‐PU polymers displayed multiple endotherms. The first endotherm was related to a short‐range ordering of the hard segment domain (Region I), and the second endotherm was ascribed to a long‐range ordering of the domain (Region II). The wide‐angle X‐ray demonstrated that the structure in Region I and Region II was almost completely amorphous. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3489–3501, 2001     

Synthesis and characterization of inherently flame‐retardant and anti‐dripping thermoplastic poly(imides‐urethane)s

A series of thermoplastic poly(imide‐urethane)s (TPIUs), based on 4,4′‐diphenylmethane diisocyanate (MDI) and pyromellitic anhydride (PMDA) as hard segments and poly(tetrahydrofuran) (PTMG) as soft segments, has been prepared by a two‐step polymerization process. The objective of this study is to prepare a type of intrinsically flame‐retardant polyurethane by incorporating PMDA as a flame retardant in the main chains. The thermal behavior and flame retardancies of the TPIUs have been characterized by thermal gravimetric (TG) analysis and limiting oxygen index (LOI), UL‐94 vertical burning, cone calorimeter tests. The results indicate that the TPIUs display outstanding performance. The temperature at 5% mass loss (T_5%) and LOI value increase with the hard‐segment contents, while the total heat released (THR) and peak heat release rate (p‐HRR) show the opposite trend. Furthermore, the T_5% of TPIU211 (molar ratio: MDI : PTMG : PMDA = 2 : 1 : 1) is 33.2°C higher than that of the conventional thermoplastic polyurethane TPU211 (molar ratio: MDI : PTMG : 1,4‐butanediol = 2 : 1 : 1), and the THR and p‐HRR of TPIU211 are 14.62% and 64.02% lower than the respective parameters of TPU211. In addition, UL‐94 vertical burning tests show that the TPIUs exhibit excellent antidripping effects. The ultimate tensile strengths of the TPIUs reached 23.1?37.6 MPa with increasing hard segment contents, which meets the requirement of mechanical properties with regard to practical use. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40801.     

Synthesis and properties of polyurethane ionomers based on carboxylated polycaprolactone

Polycaprolactone containing carboxyl groups (CPCL, M̄_n = 1200) was prepared from caprolactone (CL) and dimethylol propionic acid (DMPA). Based on the CPCL, 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol (BD), a novel series of polyurethane ionomers could be synthesized with ions in the soft segment. The tensile modulus and ultimate elongation of the ionomer cast films increased, and the glass transition temperature of the CPCL‐rich phase moved to a higher temperature after ionization. Moreover, this kind of ionomers showed small amounts of hard segment crystallinity by DSC. WAXD shows an ionic peak at 2θ = 8.6° for the ionomer with carboxylate in the hard segment, which is not present in the ionomer with carboxylate in the soft segment. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 2049–2056, 2000     

In Situ synthesis of multiblock copolymers of poly(ϵ‐caprolactone) with different poly(ether diols) based polyurethane by reactive extrusion

Polyurethanes with multiblock copolymers of poly(?‐caprolactone) (PCL) and poly(tetramethylene oxide) glycol (PTMG) or poly(ethylene glycol) (PEG) as a soft segment were synthesized in situ via reactive extrusion from ?‐caprolactone (CL) and 4,4′‐diphenylmethane diisocyanate (MDI). The titanium alkoxide mixture generated from an ester‐exchange reaction between titanium propoxide [Ti(OPr)₄], and excessive PTMG or PEG was used as an initiator and catalyst. Compared to the reported fabrication of polycaprolactone‐based polyurethane (PCLU), the in situ reactive extrusion preparation not only explored a new rapid route for the fabrication of PCLU but also offered a simplified, controllable approach for the production of PCLU in a successive mass scale. A series of PTMG–PCLUs and PEG–PCLUs with different PCL block‐average degrees of polymerization (DP_n's) were prepared by only an adjustment of the relative concentration of CL in the reaction system, with a certain constant molar ratio of MDI to titanium alkoxide. ¹H‐NMR, gel permeation chromatography, and differential scanning calorimetry results indicate that all of the CL monomers were converted in the polymerization, and the molecular weight of the copolymers was about 8 × 10⁴ g/mol with a polydispersity index of approximate 2.4. With an increase in the PCL block‐average DP_n in PTMG–PCLU from 25 to 40, the tensile strength increased from 16.5 to 22.7 MPa, and the melting point increased from 46.1 to 49.5°C. It was also verified by PEG–PCLU prepared with organic Ti of lowered content in the initiator mixture that the mechanical properties could be greatly affected and dropped with decreasing content of organic Ti in the initiator mixture. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Emulsion of polyurethane having thermosetting properties. II. Relation between the mechanical properties of film and the polyurethane structure

A self-emulsifiable polyurethane emulsion having thermosetting property was prepared by the following procedure: the polyurethane–urea–amine was first prepared by the reaction of diethylene–triamine with a prepolymer containing terminal isocyanate groups in a ketone solvent, and then the primary amino group in the polyurethane–urea–amine was reacted with epichlorohydrin. The mixture was neutralized with an aqueous acid, and finally the ketone solvent was removed by distillation in vacuo. In the polyurethane, polytetramethylene glycol (PTMG) was the base polymer functioning as the soft segment. The present paper reports the effects of the following variables on the mechanical properties of the film prepared from the polyurethane emulsion, i.e., the M _n of PTMG, the molar ratio of diethylene–triamine (DTA) to prepolymer containing terminal isocyanate groups, the structure of the isocyanate end group and the molar ratio of tolylene diisocyanate (TDI) with PTMG. The best elastomer property was realized when M_n of PTMG was 2000, TDI/PTMG molar ratio was 2.0, and prepolymer/DTA molar ratio was 0.85.     

Blocking of soft segments with different chain lengths and its impact on the shape memory property of polyurethane copolymer

The arrangements, whether block or random type, of the soft segments of polyurethane block copolymers prepared with MDI and two kinds of poly(tetramethylene glycol) (PTMG; MW of 1000 or 2000) in various ratios were compared for possible effects on the physical properties of the copolymers. A long soft segment, PTMG‐2000, was superior in all mechanical properties (strain, stress, and modulus) because a long chain length could provide more motional freedom than a short one (PTMG‐1000) could and therefore was helpful in forming strong interchain attractions among hard segments. Inclusion of more PTMG‐2000 led to a lower T_g and a peak shift in infrared spectra. The arrangement of two soft segments in a block‐type copolymer, a key finding in this study, was controlled by separately synthesizing two prepolymers, each with a different chain length, and connecting two prepolymers in a second step. Random‐type copolymers prepared for purposes of comparison were allowed to react with two PTMGs in one step. Two types of copolymers were compared, and the reason for the differences in the shape memory property are discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1435–1441, 2007     

Alkali reduction and reactive dye dyeing of T/N nonwoven fabrics dipped into silicon‐containing,water‐borne polyurethane

Two series of anionic water‐borne polyurethanes with alkali resistance and covalent bonds of a reactive dye were synthesized with different molar ratios of poly(tetramethylene glycol) (PTMG). They were classified with respect to PTMG 1000 and PTMG 2000. The fiber blends of polyester/nylon nonwoven fabrics were dipped into silicon‐containing, water‐borne polyurethane and squeezed to an 80% pickup ratio. Finally, the manmade leather was treated with alkali reduction and dyed with a reactive dye. The alkali reduction and the thermal, mechanical, and dyeing properties of the manmade leather were studied. For alkali reduction, different ratios of NaOH and Na₂CO₃ concentrations were used. Na₂CO₃ was used because of its better spreading and buffering properties. The softness and breaking load were measured and related to the weight reduction. For the dyeing properties, a reactive dye with vinyl sulfone groups was found to bond with the OH group of water‐borne polyurethane by covalent bonding. On the basis of alkali reduction, a mixture of NaOH and Na₂CO₃ with a concentration ratio of 0.1N/0.2N could lead to better softness and alkali reduction of leather. For the mechanical properties, leather of the PTMG 1000 series showed a higher breaking load than leather of the PTMG 2000 series. However, less elongation in the PTMG 1000 series resulted. Differential scanning calorimetry showed an endothermic peak at 50–100°C. This indicated that the glass‐transition temperature of the hard segment decreased with an increasing amount of the soft segment in leather; meanwhile, both the glass‐transition temperature of the soft segment and the melting temperature of the hard segment also decreased as the content of the soft segment increased. For the dyeing properties, the reactive blue dye could reach up to 96.1% dye uptake in the polyurethane part of the leather. Moreover, the washing fastness could be graded as high as 4–5, and the light resistance was also graded to 4–5, in the dyed leather. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2324–2335, 2005     

Thermal stability of polyurethane elastomers before and after UV irradiation

In this work, we investigated the thermal degradation behavior of segmented polyurethane (PUR) elastomers before and after UV irradiation. The thermal degradation of PUR elastomers was studied over the temperature range of 25–600°C in an atmosphere of nitrogen using thermal gravimetric analysis (TGA). Four series of PUR elastomers derived from poly(oxytetramethylene)glycol (PTMO) of 1000 and 2000 molecular weight and poly(caprolactone glycol) (PCL) of 1250 molecular weight, 4,4′‐diphenylmethane diisocyanate (MDI), and 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI) and 1,4‐butanediol as an chain extender were synthesized by the prepolymer method. The derivative thermogravimetric (DTG) peaks observed in the experiments indicated that PUR elastomers degraded through two steps. We attributed the first step to degradation of the hard segment. The second degradation step could be ascribed to degradation of the soft segment. We found that the PUR elastomers based on poly(ester polyol) and aromatic diisocyanate exhibit better thermal stability than that of PUR elastomers based on the poly(ether polyol) soft segment in both steps of degradation. The thermal degradation is more prevalent in PUR elastomers based on cycloaliphatic diisocyanate. The higher values of the temperature of initial decomposition (Tⁱ) indicate a higher thermal stability of UV‐exposed elastomers on the beginning of degradation. This may be due to the formation of a crosslinking structure in the presence of UV irradiation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 864–873, 2001     

Fireproofing of polyurethane elastomers by reactive organophosphonates

Polyurethane elastomers were prepared with hydroxytelechelic polybutadiene (HTPB) as polyol, modified 4,4′‐diphenylmethane diisocyanate (modified MDI) as liquid polyisocyanate, and phosphonate diols as chain extenders and flame retardant compounds. These phosphonate diols were synthesized by radical thiol–ene addition of allyl or vinyl dialkyl phosphonate to 3‐mercapto‐1,2‐propanediol. For various percentages of phosphorus (0 to 3%, w/w), polyurethane elastomers remain stable up to 250 °C. The percentage of residual char at 600 °C increases with increasing phosphorus content. For the soft segments, no variation in the glass transition temperature (T_g) is observed as the percentage of P increases, whereas the T_g of hard segments increases. Above 0.5% phosphorus content, the limiting oxygen index (LOI) becomes higher than the percentage of oxygen in the air. © 2003 Society of Chemical Industry     

低压变(LCS)特种聚氨酯微孔弹性体研制

分别以不同异氰酸酯、端羟基聚二甲基硅氧烷(HTPDMS)、聚四氢呋喃醚二醇(PTMG2000)和扩链剂等为原料,采用半预聚法工艺制备了有机硅链段改性的低压缩永久变形(LCS)聚氨酯微孔弹性体(MPU)。探讨了预聚物类型、扩链剂类型、HTPDMS添加量、R值、硬段含量等因素对MPU力学性能特别是30%压缩永久变形(70℃、22 h)的影响。结果表明,采用液化MDI为异氰酸酯组分、自制902为扩链剂、R值为1.05、硬段质量分数为22%、软段中HTPDMS质量分数为15%时,压缩永久变形为1.8%,满足LCS要求。     

Seawater degradable thermoplastic polyurethanes

Degradable thermoplastic polyurethane (TPU) elastomers incorporating poly(D ,L ‐lactide‐co‐glycolide) (PLGA) were synthesized and characterized. The soft segments consisted of a mixture of poly(butylene adipate) (PBA) and PLGA with PBA/PLGA ratios of 100/0, 75/25, and 50/50 wt %. Two PLGA polyesters were used. BD‐PLGA was initiated from butanediol; whereas BHMBA‐PLGA was initiated from 2,2‐bis‐(hydroxymethyl)butanoic acid. The hard segments consisted of dicyclohexylmethane‐4,4′‐diisocyanate (H₁₂MDI) and 1,4‐butanediol (BD). The hard segment content, expressed as the weight ratio of BD to polyol used in the TPU formulation, was set either at 8 or 12% (31.2 or 38.1% hard segment by weight, respectively). In all cases initial [NCO]/[OH] ratio was 1.03. The tensile modulus of the TPUs ranged from 9 to 131 MPa and ultimate strains ranged from 100 to 750%. DMA was used to probe the thermomechanical transitions of the TPUs and indicated useful application temperatures from well below zero up to 60–80°C depending on the formulation. Hydrolytic degradation of the TPUs was tested in seawater at 37°C. All of the PLGA‐containing TPUs showed enhanced degradation compared to those with only PBA as the soft segment. The latter compositions remained essentially unchanged throughout the test while the PLGA‐containing TPUs lost as much as 45% of their initial mass in 153 days. Molecular weights of TPUs containing degradable polyols were lower than those derived from 100% PBA polyol. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Segmented block copolymers of natural rubber and bisphenol A–toluene diisocyanate oligomers

Segmented block copolymers were synthesized from hydroxyl‐terminated liquid natural rubber and polyurethane oligomers based on Bisphenol A and toluene diisocyanate by one‐shot and two‐shot processes in solution. Structural features were characterized by infrared and nuclear magnetic resonance spectroscopic analysis. The spectra of the one‐shot materials were identical with those of the two‐shot materials, indicating their chemical identity. The soft segment T_g was well defined and almost invariant around −64°C, but the hard segment T_g varied from 75 to 105°C as the hard segment content increased from 30 to 60 wt %. Two relaxation temperatures were observed for each sample in dynamic mechanical analysis (DMA). These observations and the two‐stage thermal decomposition by random nucleation mechanism, as investigated in thermogravimetric analysis unambiguously confirmed complete phase segregation in these materials. The scanning electron microscopy and optical micrographs showed well‐defined domains dispersed in a matrix, indicating the two‐phase morphology. Systematic changes in hardness and tensile properties with hard segment content were also observed. The samples behaved like soft elastomers at lower hard segment content, toughened plastics at high hard segment content, and rigid elastomers at intermediate compositions. Variations in hardness and tear strength were consistent with this behavior. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 706–721, 1999     

Properties of Waterborne Polyurethane Adhesives: Effect of Chain Extender and Polyol Content

A series of waterborne polyurethane (WBPU) adhesives were prepared with various ratios of polyol, poly(tetramethylene oxide glycol) (PTMG), and chain extender, ethylene diamine (EDA), at a fixed content of diisocyanate, 4,4-dicyclohexylmethane diisocyanate (H₁₂MDI) and hydrophilic agent, 2,2-dimethylol propionic acid (DMPA). WBPU adhesives were characterized by IR and ¹H-NMR spectroscopies, X-ray diffraction (XRD) and gel permeation chromatography (GPC). It was found that the extent of hydrogen bonds between hard–hard segment (i.e., hydrogen bonds between the NH and carbonyl groups) increased with increasing chain extender content (decreasing polyol content). Moreover, the disordered hydrogen bond of carbonyl group (hydrogen bond of urethane groups in the interfacial region) increased with increasing chain extender content (decreasing polyol content). The cyclic urea and allophanate group, which are attributed to the side reaction and cross-linking reaction, respectively, were found above a molar ratio 0.17 of chain extender to diisocyanate. The adhesive strength was maximum with 0.95 wt% and 63.10 wt% chain extender and soft segment (PTMG), respectively (H2 sample) at room temperature for the WBPU adhesive. However, with increasing application temperature the adhesive strength decreased for all samples.     

Synthesis of polyurethane–imide (PU–imide) copolymers with different dianhydrides and their properties

This study reports the synthesis of polyurethane–imide (PU–imide) copolymers using 4,4′-diphenylmethane diisocyanate (MDI) polytetramethylene glycols (PTMGs) and different aromatic dianhydrides. Differential scanning calorimetry (DSC) results indicate that PU–imide copolymers had two phase structures containing four transition temperatures (T_gs, T_ms, T_gh and T_mh). However, only PU–imide copolymers were formed by soft PTMG(2000) segments possessing a T_ms (melting point of soft segment). When different aromatic dianhydrides were introduced into the backbone chain of the polyurethane, although the T_gs (glass transition temperature of the soft segment) of some of PU–imide copolymers did not change, the copolymers with long soft segments had low T_gs values. The T_gh (glass transition temperature of hard segment) values of PU–imide copolymers were higher than that of polyurethane (PU). In addition, the high hard segment content of PU–imide copolymer series also had an obvious T_mh (melting point of hard segment). According to thermogravimetric analysis (TGA) and differential thermogravimetric analysis (DTGA), the PU–imide copolymers had at least two stages of degradation. Although the T_di (initial temperature of degradation) depended on the hard segment content and the composition of hard segment, the different soft segment lengths did not obviously influence the T_di. However, PU–imide copolymers with a longer soft segment had a higher thermal stability in the degradation temperature range of middle weight loss (about T_d 5%–50%). However, beyond T_d 50% (50% weight loss at temperature of degradation), the temperature of degradation of PU–imide copolymers increased with increasing hard segment content. Mechanical properties revealed that the modulus and tensile strength of PU–imide copolymers surpassed those of PU. Wide angle X-ray diffraction patterns demonstrated that PU–imide copolymers are crystallizable. © 1999 Society of Chemical Industry     

Study on the influence of thermal characteristics of hyperbranched polyurethane phase change materials for energy storage

A series of hyperbranched polyurethane (HB‐PU) phase change induced energy storage materials were prepared by polyethylene glycol (PEG), methylene diphenyl 4,4′‐diisocyanate (MDI), and hyperbranched polyester polyalcohol via a two‐step process. The influence of thermal characteristics of HB‐PU was investigated using differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD). It has been found that the thermal characteristics of HB‐PU are affected by some factors. Such as the molecular weight and content of soft segment, once the M_n of PEG soft segments is larger than the critical M_n (2000 g/mol), both the phase change enthalpy and temperature increase as M_n of PEG soft segment and soft segment content (SSC) increase. The influence of the microstructure of hard segment originates from diisocyanate and hyperbranched polyester polyalcohol, HB‐PUs with regular microstructure and lower generation of hyperbranched polyester polyalcohol have high energy storage capability. Furthermore, the conditions of measurement affect the thermal characteristics of materials. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Morphology of polyurethane–isocyanurate elastomers

The dynamic viscoelastic properties and thermal transition behavior of reaction injection molding (RIM) and cast polyurethane—isocyanurate elastomers have been studied as a function of various segments (soft and hard urethane, and hard isocyanurate) content. RIM and cast elastomers were prepared at different concentrations of soft and hard urethane, and hard isocyanurate segments. RIM elastomers with the higher isocyanate index (lower hard urethane and greater isocyanurate segment content) displayed an unchanged T_g (glass transition temperature of soft segment) and increasing T_gh (glass transition temperature of hard segment) related to the hard urethane and isocyanurate segments. This is due to the phase separation between the soft and the hard segments. Cast elastomers synthesized from the higher amount of 1,4-butanediol (greater hard urethane and less hard isocyanurate segment content) showed an increasing T_gs, decreasing T_gh of hard urethane segments, and an unchanged T_gh of isocyanurate segments. This is related to the phase mixing between the soft and the hard urethane segments and the phase separation of hard isocyanurate and hard urethane segments.     

Synthesis and characterization of poly[(butylene succinate)‐co‐(butylene terephthalate)]‐b‐poly(tetramethylene glycol) segmented block copolymer

Polyester‐polyether segmented block copolymers of poly[(butylene succinate)‐co‐poly(butylene terephthalate)] (PBS–PBT) and poly(tetramethylene glycol) (PTMG) (M_n = 2000) with various compositions were synthesized. PBT content in the PBS was adjusted to ca. 5 mol %. Their thermal and mechanical properties were investigated. In the case of copolymer, the melting point of the PBS–PBT control was 107.8°C, and the melting point of the copolymer containing 70 wt % of PTMG was 70.1°C. Crystallinity of soft segment was 5 ∼ 17%, and that of hard segment was 42 ∼ 59%. The breaking stress of the PBS–PTMG control was 47 MPa but it decreased with increasing PTMG content. In the case of copolymer containing 70 wt % of PTMG, breaking stress was 36 MPa. Contrary to the decreasing breaking stress, breaking strain increased from 300% for PBS–PBT control to 900% for a copolymer containing 70 wt % of PTMG. The shape recovery ratios of the copolymer containing 70 wt % PTMG were almost twice of those of copolymers containing 40 wt % PTMG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2067–2075, 2001     

Properties of segmented polyurethanes derived from different diisocyanates

Various segmented polyurethane materials with a polyurethane hard segment (HS) content of 40 wt % were prepared by bulk polymerization of a poly(tetramethylene ether) glycol with M_n of 2000, 1,4‐butanediol, and various diisocyanates. The diisocyanates used were pure 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluene diisocyanate (T100), toluene diisocyanate containing 80% 2,4‐isomer and 20% 2,6‐isomer (T80), isophorone diisocyanate (IPDI), hydrogenated 4,4′‐diphenylmethane diisocyanate (HMDI), and 1,6‐hexane diisocyanate (HDI). The segmented polyurethane materials were characterized by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), tensile properties, tear strength, and Shore A hardness. The DSC and DMA data show that the thermal transitions are influenced significantly by the diisocyanate structure. In the segmented polyurethane materials with aliphatic HS, the polyether soft segment (SS) is immiscible with the HS. However, in the segmented polyurethane materials with aromatic HS, the SS is partially miscible with the HS. The diisocyanate structure also influences the mechanical properties significantly and is described as the effect of symmetry and chemical structure of the HS. Various solution polymerized polyurethane resins with solid content of 30 wt % were also prepared and their thickness retention, water resistance, and yellowing resistance were determined for the evaluation of their usage as wet process polyurethane leather. The polyurethane resin with aliphatic HS show poorer thickness retention but better yellowing resistance. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 167–174, 2000