Thermodynamic Properties at Saturation Derived from Experimental Two-Phase Isochoric Heat Capacity of 1-Hexyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide

New measurements are reported for the isochoric heat capacity of the ionic liquid substance 1-hexyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide ([C6mim][NTf2]). These measurements extend the ranges of our earlier study (Polikhronidi et al. in Phys Chem Liq 52:657, 2014) by 5 % of the compressed liquid density and by 75 K. An adiabatic calorimeter was used to measure one-phase \((C_{\mathrm{V1}})\) liquid and two-phase \((C_{\mathrm{V2}})\) liquid + vapor isochoric heat capacities, densities \((\rho _s)\), and phase-transition temperatures \((T_s)\) of the ionic liquid (IL) substance. The combined expanded uncertainty of the density \(\rho \) and isochoric heat capacity \(C_\mathrm{V}\) measurements at the 95 % confidence level with a coverage factor of \(k = 2\) is estimated to be 0.15 % and 3 %, respectively. Measurements are concentrated in the immediate vicinity of the liquid + vapor phase-transition curve, in order to closely observe phase transitions. The present measurements and those of our earlier study are analyzed together and are presented in terms of thermodynamic properties \((T_s\), \(\rho _s\), \(C_{\mathrm{V1}}\) and \(C_{\mathrm{V2}})\) evaluated at saturation and in terms of key-derived thermodynamic properties \(C_\mathrm{P}\), \(C_\mathrm{S}\), \(W_\mathrm{S}^{{\prime }}\), \(K_{\mathrm{TS}}^{{\prime }}\), \(\left( {\partial P/\partial T} \right) _{\mathrm{V}}^{\prime }\), and \(\left( {\partial V/\partial T} \right) _\mathbf{P}^{\prime })\) on the liquid + vapor phase-transition curve. A thermodynamic relation by Yang and Yang is used to confirm the internal consistency of measured two-phase heat capacities \(C_{\mathrm{V2}} \), which are observed to fall perfectly on a line as a function of specific volume at a constant temperature. The observed linear behavior is exploited to evaluate contributions to the quantity \(C_{\mathrm{V2}} = f(V, T)\) from chemical potential \(C_{{\mathrm{V}\upmu }} =-T\frac{\mathrm{d}^{{2}}\mu }{\mathrm{d}T^{2}}\) and from vapor pressure \(C_{\mathrm{VP}} =VT\frac{\mathrm{d}^{2}P_{\mathrm{S}} }{\mathrm{d}T^{2}}\). The physical nature and specific details of the temperature and specific volume dependence of the two-phase isochoric heat capacity and some features of the other derived thermodynamic properties of IL at liquid saturation curve are considered in detail.     

Thermal Conductivity of Pyroclastic Soil (<Emphasis Type="BoldItalic">Pozzolana</Emphasis>) from the Environs of Rome

The paper reveals the experimental procedure and thermo-physical characteristics of a coarse pyroclastic soil (Pozzolana), from the neighborhoods of Rome, Italy. The tested samples are comprised of 70.7 % sand, 25.9 % silt, and 3.4 % clay. Their mineral composition contained 38 % pyroxene, 33 % analcime, 20 % leucite, 6 % illite/muscovite, 3 % magnetite, and no quartz content was noted. The effective thermal conductivity of minerals was assessed to be about \(2.14\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\). A transient thermal probe method was applied to measure the thermal conductivity (\(\lambda \)) over a full range of the degree of saturation \((S_{\mathrm{r}})\), at two porosities (n) of 0.44 and 0.50, and at room temperature of about \(25\,^{\circ }\hbox {C}\). The \(\lambda \) data obtained were consistent between tests and showed an increasing trend with increasing \(S_{\mathrm{r}}\) and decreasing n. At full saturation (\(S_{\mathrm{r}}=1\)), a nearly quintuple \(\lambda \) increase was observed with respect to full dryness (\(S_{\mathrm{r}}=0\)). In general, the measured data closely followed the natural trend of \(\lambda \) versus \(S_{\mathrm{r}}\) exhibited by published data at room temperature for other unsaturated soils and sands. The measured \(\lambda \) data had an average root-mean-squared error (RMSE) of \(0.007\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) and \(0.008\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) for n of 0.50 and 0.44, respectively, as well as an average relative standard deviation of the mean at the 95 % confidence level \((\hbox {RSDM}_{0.95})\) of 2.21 % and 2.72  % for n of 0.50 and 0.44, respectively.     

Scaling behavior of dynamic hysteresis in Bi<Subscript>3.15</Subscript>Nd<Subscript>0.85</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> ceramics

The scaling behavior of dynamic hysteresis was investigated in Bi_3.15Nd_0.85Ti₃O₁₂ bulk ceramics at a frequency of 1–1000 Hz and an external electric field amplitude of 79–221 kV/cm. The scaling behavior at low amplitude (E ₀ ≤ 114 kV/cm) takes the form of \(\langle A \rangle \propto f^{ - 0.013} E_{0}^{0.7}\) for low frequency (f ≤ 200 Hz) and \(\langle A \rangle \propto f^{ - 0.013} E_{0}^{0.22}\) for high frequency (f > 200 Hz), where \(\langle A \rangle\) is the area of hysteresis loop and f and E ₀ are frequency and amplitude of external electric field, respectively. At high amplitude (E ₀ > 114 kV/cm), we obtain \(\langle A \rangle \propto f^{0.011} E_{0}^{1.163}\) at low frequency and \(\langle A \rangle \propto f^{ - 0.015} E_{0}^{0.7}\) at high frequency. At low E ₀, the contribution to the scaling relation mainly results from reversible domain switching, while at high E ₀ reversible and irreversible domain switching concurrently contribute to the scaling relation.     

Interaction of Glycylglycine with Cationic Surfactants—Cetylpyridinium Chloride and Cetylpyridinium Bromide: A Volumetric,Ultrasonic and Conductometric Study

The interactions of glycylglycine (di-peptide of glycine) also known as 2-[(2-aminoacetyl)amino] acetic acid with cationic surfactants cetylpyridinium chloride (CPC) and cetylpyridinium bromide (CPB) as a function of temperature in aqueous medium has been studied by well-know permutation of volumetric, ultrasonic and conductometric techniques. These measurements have been used to evaluate some useful thermodynamic parameters viz. apparent molar volumes, \( \phi_{v} \), partial molar volumes, \( \phi_{v}^{o} \), transfer volumes, \( \phi_{\text{v}}^{0} (tr) \), partial molar expansibility, \( \phi_{E}^{0} \), hydration number, n_H, apparent molal compressibility, \( \phi_{K} \), limiting partial molal adiabatic compressibility, \( \phi_{K}^{0} \). The specific conductivity (κ) was used to calculate the critical micellar concentration (cmc) and other physicochemical parameters of micellization of CPC/CPB with glycylglycine. The critical micelle concentration, cmc and limiting molar conductivity, \( \varLambda_{m}^{o} \) of the two surfactant systems were determined by using the conductivity data at 298.15 K, 303.15 K, 308.15 K and 313.15 K. The acquired data have been discussed as per various interactions taking place in the ternary system of CPC/CPB, glycylglycine and water.     

Fracture of pre-cracked thin metallic conductors due to electric current induced electromagnetic force

We investigated propagation of a sharp crack in a thin metallic conductor with an edge crack due to electric current induced electromagnetic forces. Finite element method (FEM) simulations showed mode I crack opening in the edge-cracked conductor due to the aforementioned (i.e., self-induced) electromagnetic forces. Mode I stress intensity factor due to the self-induced electromagnetic forces, \(K_{\mathrm{IE},}\) was evaluated numerically as \(K_{\mathrm{IE}}=\upmu l^{2}j^{2}(\uppi a)^{0.5}f(a/w)\), where \(\upmu \) is the magnetic permeability, l is the length of the conductor, a is the crack length, j is the current density, w is the width of the sample and f(a / w) is a geometric factor. Effect of dynamic electric current loading on edge-cracked conductor, incorporating the effects of induced currents, was also studied numerically, and dynamic stress intensity factor, \(K_{\mathrm{IE,d}}\), was observed to vary as \(K_{\mathrm{IE,d}} \sim f_{d}(a/w)j^{2}(\uppi a)^{1.5}\). Consistent with the FEM simulation, experiments conducted using \(12\,\upmu \hbox {m}\) thick Al foil with an edge crack showed propagation of sharp crack due to the self-induced electromagnetic forces at pulsed current densities of \(\ge \) \(1.85\times 10^{9}\,\hbox {A/m}^{2}\) for \(a/w = 0.5\). Further, effects of current density, pulse-width and ambient temperature on the fracture behavior of the Al foil were observed experimentally and corroborated with FEM simulations.     

Superconducting Properties of NdO<Subscript>0.5</Subscript><Emphasis Type="Bold">F</Emphasis><Subscript>0.5</Subscript>BiS<Subscript>2</Subscript> Single Crystals

We report on superconducting properties of high-quality single crystals of F-substituted NdOBiS₂ using low-temperature magnetization and transport measurements. Using the mixture of CsCl and KCl as the flux, we have synthesized our single crystals. This compound exhibits bulk superconductivity with a transition temperature of about T _c～4.6 K. The critical current density J _c as a function of temperature has been derived and decreases with the increasing temperature. We construct the phase diagram H _c2(T). The zero-temperature value for \(H_{\mathrm {c2}}^{B\parallel c}\) for value for \(T_{c}^{90~\%}\) and \(T_{c}^{0~\%}\) is estimated to be approximately 2.17 and 1.72 T respectively by using Werthamer-Helfand-Hohenberg model.     

Partial permutation decoding for MacDonald codes

We show how to find s-PD-sets of the minimal size \(s+1\) for the \(\left[ \frac{q^n-q^u}{q-1},n,q^{n-1}-q^{u-1}\right] _q \) MacDonald q-ary codes \(C_{n,u}(q)\) where \(n \ge 3\) and \(1 \le u \le n-1\). The construction of [6] can be used and gives s-PD-sets for s up to the bound \(\lfloor \frac{q^{n-u}-1}{(n-u)(q-1)} \rfloor -1\), of effective use for u small; for \(u \ge \lfloor \frac{n}{2} \rfloor \) an alternative construction is given that applies up to a bound that depends on the maximum size of a set of vectors in \(V_u(\mathbb {F}_q)\) with each pair of vectors distance at least 3 apart.     

A comparative study on dielectric behaviours of Au/(Zn-doped PVA)/<Emphasis Type="Italic">n</Emphasis>-4H-SiC (MPS) structures with different interlayer thicknesses using impedance spectroscopy methods

Three different thicknesses (50, 150 and 500 nm) Zn-doped polyvinyl alcohol (PVA) was deposited on n-4H-SiC wafer as interlayer by electrospinning method and so, Au/(Zn-doped PVA)/n-4H-SiC metal–polymer–semiconductor structures were fabricated. The thickness effect of Zn-doped PVA on the dielectric constant (\(\varepsilon ^{\prime }\)), dielectric loss (\(\varepsilon ^{{\prime }{\prime }}\)), loss-tangent (tan \(\delta \)), real and imaginary parts of electric modulus (\(M^{\prime }\) and \(M^{{\prime }{\prime }})\) and ac electrical conductivity \((\sigma _{\mathrm{ac}})\) of them were analysed and compared using experimental capacitance (C) and conductance (\(G/\omega \)) data in the frequency range of 1–500 kHz at room temperature. According to these results, the values of \(\varepsilon ^{\prime }\) and \(\varepsilon ^{{\prime }{\prime }}\) decrease with increasing frequency almost exponentially, \(\sigma _{\mathrm{ac}}\) increases especially, at high frequencies. The \(M^{\prime }\) and \(M^{{\prime }{\prime }}\) values were obtained from the \(\varepsilon ^{\prime }\) and \(\varepsilon ^{{\prime }{\prime }}\) data and the \(M^{\prime }\) and \(M^{{\prime }{\prime }}\) vs. f plots were drawn for these structures. While the values of \(\varepsilon ^{\prime }\), \(\varepsilon ^{{\prime }{\prime }}\) and tan \(\delta \) increase with increasing interlayer thickness, the values of \(M^{\prime }\) and \(M^{{\prime }{\prime }}\) decrease with increasing interlayer thickness. The double logarithmic \(\sigma _{\mathrm{ac}}\) vs. f plots for each structure have two distinct linear regimes with different slopes, which correspond to low and high frequencies, respectively, and it is prominent that there exist two different conduction mechanisms. Obtained results were found as a strong function of frequency and interlayer thickness.     

Cyclic codes over $${\mathbb {F}}_{2^m}[u]/\langle u^k\rangle $$ of oddly even length

Let \({\mathbb {F}}_{2^m}\) be a finite field of characteristic 2 and \(R={\mathbb {F}}_{2^m}[u]/\langle u^k\rangle ={\mathbb {F}}_{2^m} +u{\mathbb {F}}_{2^m}+\ldots +u^{k-1}{\mathbb {F}}_{2^m}\) (\(u^k=0\)) where \(k\in {\mathbb {Z}}^{+}\) satisfies \(k\ge 2\). For any odd positive integer n, it is known that cyclic codes over R of length 2n are identified with ideals of the ring \(R[x]/\langle x^{2n}-1\rangle \). In this paper, an explicit representation for each cyclic code over R of length 2n is provided and a formula to count the number of codewords in each code is given. Then a formula to calculate the number of cyclic codes over R of length 2n is obtained. Moreover, the dual code of each cyclic code and self-dual cyclic codes over R of length 2n are investigated.     

Electrical and Thermal Characteristics of the Insulator–Metal Transition in Crystalline $$\hbox {V}_{2}\hbox {O}_{5}$$ Films

The electrical and thermal properties with respect to the crystallization in \(\hbox {V}_{2}\hbox {O}_{5}\) thin films were investigated by measuring the resistance at different temperatures and applied voltages. The changes in the crystal structure of the films at different temperatures were also explored using Raman measurements. The thermal diffusivity of the crystalline \(\hbox {V}_{2}\hbox {O}_{5}\) film was measured by the nanosecond thermoreflectance method. The microstructures of amorphous and crystalline \(\hbox {V}_{2}\hbox {O}_{5}\) were observed by SEM and XRD measurements. The temperature-dependent Raman spectra revealed that a structural phase transition does not occur in the crystalline film. The resistance measurements of an amorphous film indicated semiconducting behavior, whereas the resistance of the crystalline film revealed a substantial change near \(250\,{^{\circ }}\hbox {C}\), and Ohmic behavior was observed above \(380\,{^{\circ }}\hbox {C}\). This result was due to the metal–insulator transition induced by lattice distortion in the crystalline film, for which \(T_{\mathrm{c}}\) was \(260\,{^{\circ }}\hbox {C}\). \(T_{\mathrm{c}}\) of the film decreased from 260 \({^{\circ }}\hbox {C}\) to \(230\,{^{\circ }}\hbox {C}\) with increasing applied voltage from 0 V to 10 V. Furthermore, the thermal diffusivity of the crystalline film was \(1.67\times 10^{-7}\,\hbox {m}^{2}\cdot \hbox {s}^{-1}\) according to the nanosecond thermoreflectance measurements.     

The Effect of Inhomogeneous Phase on the Critical Temperature of Smart Meta-superconductor MgB<Subscript>2</Subscript>

The critical temperature (T_C) of MgB₂, one of the key factors limiting its application, is highly desired to be improved. On the basis of the meta-material structure, we prepared a smart meta-superconductor structure consisting of MgB₂ micro-particles and inhomogeneous phases by an ex situ process. The effect of inhomogeneous phase on the T_C of smart meta-superconductor MgB₂ was investigated. Results showed that the onset temperature (\(T_{\mathrm {C}}^{\text {on}}\)) of doping samples was lower than those of pure MgB₂. However, the offset temperature (\({T}_{\mathrm {C}}^{\text {off}}\)) of the sample doped with Y₂O₃:Eu³⁺ nanosheets with a thickness of 2 ～ 3 nm which is much less than the coherence length of MgB₂ is 1.2 K higher than that of pure MgB₂. The effect of the applied electric field on the T_C of the sample was also studied. Results indicated that with the increase of current, \({T}_{\mathrm {C}}^{\text {on}}\) is slightly increased in the samples doping with different inhomogeneous phases. With increasing current, the \({T}_{\mathrm {C}}^{\text {off}}\) of the samples doped with nonluminous inhomogeneous phases was decreased. However, the \({T}_{\mathrm {C}}^{\text {off}}\) of the luminescent inhomogeneous phase doping samples increased and then decreased with increasing current.     

Canadian Field Soils IV: Modeling Thermal Conductivity at Dryness and Saturation

The thermal conductivity data of 40 Canadian soils at dryness \((\lambda _{\mathrm{dry}})\) and at full saturation \((\lambda _{\mathrm{sat}})\) were used to verify 13 predictive models, i.e., four mechanistic, four semi-empirical and five empirical equations. The performance of each model, for \(\lambda _{\mathrm{dry}}\) and \(\lambda _{\mathrm{sat}}\), was evaluated using a standard deviation (SD) formula. Among the mechanistic models applied to dry soils, the closest \(\lambda _{\mathrm{dry}}\) estimates were obtained by MaxRTCM \((\textit{SD} = \pm ~0.018\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1})\), followed by de Vries and a series-parallel model (\(\hbox {S-}{\vert }{\vert }\)). Among the semi-empirical equations (deVries-ave, Advanced Geometric Mean Model (A-GMM), Chaudhary and Bhandari (C–B) and Chen’s equation), the closest \(\lambda _{\mathrm{dry}}\) estimates were obtained by the C–B model \((\pm ~0.022\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1})\). Among the empirical equations, the top \(\lambda _{\mathrm{dry}}\) estimates were given by CDry-40 \((\pm ~0.021\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1}\) and \(\pm ~0.018\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1}\) for18-coarse and 22-fine soils, respectively). In addition, \(\lambda _{\mathrm{dry}}\) and \(\lambda _{\mathrm{sat}}\) models were applied to the \(\lambda _{\mathrm{sat}}\) database of 21 other soils. From all the models tested, only the maxRTCM and the CDry-40 models provided the closest \(\lambda _{\mathrm{dry}}\) estimates for the 40 Canadian soils as well as the 21 soils. The best \(\lambda _{\mathrm{sat}}\) estimates for the 40-Canadian soils and the 21 soils were given by the A-GMM and the \(\hbox {S-}{\vert }{\vert }\) model.     

Ab Initio Study of Structural,Electronic, and Magnetic Properties of $\mathrm {A}_{1-x}^{\text {III}}$MnxBVI: In1−xMnxS-Diluted Magnetic Semiconductor

First-principles density functional calculations on the new class of diluted magnetic semiconductor \(A_{1-x}^{III}{Mn}_{x}B^{VI}\) In_1?x Mn _x S for x =?0.25 and 0.5 are investigated to study the structural, electronic, and magnetic properties, employing the full-potential linearized augmented plane wave method. Electronic band structures and density of states revealed a half-metallic character of In_1?x Mn _x S and show the stability of anti-ferromagnetic states as compared with ferromagnetic states. The calculated exchange constants J _dd are in good agreement with experimental and theoretical results on magnetic properties of single crystalline \(\mathrm {A}_{1-x}^{\text {III}}{\text {Mn}}_{x}\mathrm {B}^{\text {VI}}\) in the anti-ferromagnetic case. Our predicated calculations on the s,p-d exchange constants N ₀ α and N ₀ β show that they are lower than in \(\mathrm {A}_{1-x}^{\text {II}}{\text {Mn}}_{x}\mathrm {B}^{\text {VI}}\) DMS. The local environment is found tetrahedral as in the II–VI DMS and other (III,Mn) VI compounds. The total magnetic moment for In_1?x Mn _x S for different concentrations is in accordance with the exact value 5 μ _B and comes mainly from impurity Mn. The local magnetic moments of Mn ions are reduced from their free space charges values due to the p-d hybridization which produces small magnetic moments on the nonmagnetic In and S sites. The Curie temperature of In_1?x Mn _x S is calculated within the mean field approximation and compared with other DMS systems.     

Characterization and optical properties of $$\hbox {Pr}_{2}\hbox {O}_{3}$$-doped molybdenum lead-borate glasses

\(\hbox {Pr}^{3+}\) doped molybdenum lead-borate glasses with the chemical composition 75PbO?[25–(x \(+\) y)\(\hbox {B}_{2}\hbox {O}_{3}]\)–\(y\hbox {MoO}_{3}\)–\(x\hbox {Pr}_{2}\hbox {O}_{3}\) (where \(x = 0.5\) and 1.0 mol% and \(y = 0\) and 5 mol%) were prepared by conventional melt-quenching technique. Thermal, optical and structural analyses are carried out using DSC, UV and FTIR spectra. The physical parameters, like glass transition \((T_{\mathrm{g}})\), stability factor \((\Delta T)\), optical energy band gap \((E_{\mathrm{gopt}})\), of these glasses have been determined as a function of dopant concentration. The \({T}_{\mathrm{g}}\) and optical energy gaps of these glasses were found to be in the range of 290–350\({^{\circ }}\hbox {C}\) and 2.45–2.7 eV, respectively. Stability of the glass doped with \(\hbox {Pr}^{3+}\) is found to be moderate (\(\sim \)40). The results are discussed using the structural model of Mo–lead-borate glass.     

<10$$ \bar{1} $$0> Dislocation at a {2$$ \bar{1} $$$$ \bar{1} $$0} low-angle grain boundary in LiNbO3

A LiNbO₃ bicrystal that contains a {2\( \bar{1} \) \( \bar{1} \)0} low-angle grain boundary with both of 2° tilt misorientation and a slight twist misorientation was fabricated, and resulting dislocation structure at the boundary was analyzed by using transmission electron microscopy (TEM) and scanning TEM. The observations revealed that two types of dislocations of b = 1/3 <2\( \bar{1} \) \( \bar{1} \)0> and b = <10\( \bar{1} \)0> are formed at the boundary. A 1/3 <2\( \bar{1} \) \( \bar{1} \)0> dislocation, which dissociates into two partial dislocations with a {2\( \bar{1} \) \( \bar{1} \)0} stacking fault in between, compensates only tilt misorientation of the boundary. On the other hand, it was found that a <10\( \bar{1} \)0> dislocation, which dissociates into three equivalent partial dislocations with b = 1/3 <10\( \bar{1} \)0>, has both edge and screw components in total. That is, the <10\( \bar{1} \)0> dislocations are formed to compensate the twist misorientation of the boundary, in addition to the tilt misorientation. It is interesting that the three partial dislocations from a <10\( \bar{1} \)0> dislocation are arranged in a zigzag pattern with left–right asymmetry. This special configuration is suggested to originate from the presence of stable stacking fault structure on the {2\( \bar{1} \) \( \bar{1} \)3} plane in LiNbO₃.     

High-pressure studies of superconductivity in $$\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}$$

\(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\) crystallizes in tetragonal CeOBiS\(_{2}\) structure (S. G. P4/nmm). We have investigated the effect of pressure on magnetization measurements. Our studies suggest improved superconducting properties in polycrystalline samples of \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\). The \(T_{\mathrm{c}}\) in our sample is 5.3 K, at ambient pressure, which is marginal but definite enhancement over \(T_{\mathrm{c}}\) reported earlier (= 5.1 K). The upper critical field \(H_{\mathrm{c}2}\)(0) is greater than 3 T, which is higher than earlier report on this material. As determined from the M–H curve, both \(H_{\mathrm{c}2}\) and \(H_{\mathrm{c}1}\) decrease under external pressure P (0 \(\le P \le \) 1 GPa). We observe a decrease in critical current density and transition temperature on applying pressure in \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\).     

Thermal Properties of Jojoba Oil Between $$20\,{^{\circ }}\hbox {C}$$ and $$45\,{^{\circ }}\hbox {C}$$45∘C

Vegetable oils have been widely studied as biofuel candidates. Among these oils, jojoba (Simmondsia chinensis) oil has attracted interest because it is composed almost entirely of wax esters that are liquid at room temperature. Consequently, it is widely used in the cosmetic and pharmaceutical industries. To date, research on S. chinensis oil has focused on to its use as a fuel and its thermal stability, and information about its thermal properties is scarce. In the present study, the thermal effusivity and conductivity of jojoba oil between \(20\,{^{\circ }}\hbox {C}\) and \(45\,{^{\circ }}\hbox {C}\) were obtained using the inverse photopyroelectric and hot-ball techniques. The feasibility of an inverse photopyroelectric method and a hot-ball technique to monitor the thermal conductivity, and the thermal effusivity of the S. chinensis is demonstrated. The thermal effusivity decreased from 538 \(\hbox {W}\cdot \,\hbox {s}^{1/2}\cdot \,\hbox {m}^{-2}\cdot \,\hbox {K}^{-1}\) to 378 \(\hbox {W}\cdot \,\hbox {s}^{1/2}\cdot \,\hbox {m}^{-2}\cdot \,\hbox {K}^{-1}\) as the temperature increased, whereas the thermal conductivity remained the same over the temperature range investigated in this study. The obtained results provide insight into the thermal properties of S. chinensis oil between \(20\,{^{\circ }}\hbox {C}\) and \(45\,{^{\circ }}\hbox {C}\).     

Reproducibility of the Helium-3 Constant-Volume Gas Thermometry and New Data Down to 1.9 K at NMIJ/AIST

This study confirms reproducibility of the International Temperature Scale of 1990 (ITS-90) realized by interpolation using the constant-volume gas thermometer (CVGT) of National Metrology Institute of Japan (NMIJ)/AIST with \(^{3}\)He as the working gas from 3 K to 24.5561 K by comparing the newly obtained results and those of earlier reports, indicating that the CVGT has retained its capability after renovation undertaken since strong earthquakes struck Japan. The thermodynamic temperature T is also obtained using the single-isotherm fit to four working gas densities (\(127\,\hbox {mol}\cdot \hbox {m}^{-3}\), \(145\,\hbox {mol}\cdot \hbox {m}^{-3}\), \(171\,\hbox {mol}\cdot \hbox {m}^{-3}\) and \(278\,\hbox {mol}\cdot \hbox {m}^{-3})\) down to 1.9 K, using the triple point temperature of Ne as a reference temperature. In this study, only the second virial coefficient is taken into account for the single-isotherm fit. Differences between T and the ITS-90 temperature, \(T-T_{90}\), reported in earlier works down to 3 K were confirmed in this study. At the temperatures below 3 K down to 2.5 K, \(T-T_{90}\) is much smaller than the standard combined uncertainty of thermodynamic temperature measurement. However, \(T- T_{90}\) seems to increase with decreasing temperature below 2.5 K down to 1.9 K, although still within the standard combined uncertainty of thermodynamic temperature measurement. In this study, T is obtained also from the CVGT with a single gas density of \(278\,\hbox {mol}\cdot \hbox {m}^{-3}\) using the triple-point temperature of Ne as a reference temperature by making correction for the deviation from the ideal gas using theoretical values of the second and third virial coefficients down to 2.6 K, which is the lowest temperature of the theoretical values of the third virial coefficient. T values obtained using this method agree well with those obtained from the single-isotherm fit. We also found that the second virial coefficient obtained by the single-isotherm fit to experimental results agrees well with that obtained by the single-isotherm fit to the theoretically expected behavior of \(^{3}\)He gas with the theoretical second and third virial coefficients at four gas densities used in the present work.     

The parameters governing the coefficient of dispersion of cubes in rotating cylinders

Axial dispersion of cubic particles in horizontal, rotating cylinders was investigated using discrete element modelling simulations. We found that, similar to the behavior of spheres, the axial dispersion coefficient of cubes depends on (1) the rotational speed of the cylinder \({\omega }\), (2) the acceleration due to gravity g and (3) the particle size d, satisfying the relationship \({D}_\mathrm {ax}\propto {\omega }^{1-2{\lambda }}{g}^{{\lambda }}{d}^{2-{\lambda }}\) with \({\lambda }\approx 0.15\) (\({\lambda }\approx 0.1\) for beds of spheres) (Third et al. in Powder Technol 203:510–517, 2010). This observation suggested that, although particle shape influences significantly the rate of axial dispersion (cubes disperse almost twice as fast as spheres of equal volume), the parameters controlling the coefficient of dispersion are independent of particle shape.