La2Ti2O7 Ceramics

La₂Ti₂O₇ powders were prepared using three different techniques. Single-phase material was obtained at 1150°C by calcination of mixed oxides, at 1000°C by molten salt synthesis, and at 850°C by evaporative decomposition of solutions. Particle sizes and morphologies of the powders differed substantially, as did the sintered microstructures and dielectric properties. Very dense (99%), translucent, grain-oriented lanthanum titanate was fabricated by hot-forging at 1300°C under a 200-kg load. Anisotropy was demonstrated by X-ray diffraction, scanning electron microscopy, thermal expansion, and dielectric measurements.     

Effects of La2O3/ZnO Additives on Microstructure And Microwave Dielectric Properties of Zr0.8Sn0.2TiO4 Ceramics

Dielectric ceramics of Zr_0.8Sn_0.2TiO₄ containing La₂O₃ and ZnO as sintering aids were prepared and investigated for microstructure and microwave dielectric properties. Low-level doping with La₂O₃ and ZnO (up to 0.30 wt%) is good for densification and dielectric properties. These additives do not affect the dielectric constant and the temperature coefficient. Dielectric losses increase significantly at additive levels higher than 0.15 wt%. The combined additives La₂O₃ and ZnO act as grain growth enhancers. With 0.15 wt% additives, a ceramic having a dielectric constant, a quality factor, and a temperature coefficient of frequency at 4.2 GHz of 37.6, 12 800, and –2.9 ppm/°C, respectively, was obtained. The quality factor was considerably improved by prolonged sintering.     

Structure and Electrical Properties of A-site-Deficient Perovskite Compounds in the La2/3TiO3-La1/3NbO3 System

The structure and electrical properties of an A-site-deficient perovskite compound found in the La_2/3TiO₃-La_1/3NbO₃ system were investigated. The composition of the perovskite compound seemed to be very close to La_0.633(Ti_0.90Nb_0.10)O₃. X-ray diffraction analysis revealed a superstructure with a doubled c -axis parameter, resulting from an ordered arrangement of the A-site cation vacancies. Impedance measurements on the compound showed that La_0.633(Ti_0.90Nb_0.10)O₃ had high ionic conductivity at relatively low temperature (<770 K) and increased electronic conduction at high temperature (>770 K). The bulk ionic conductivity was comparable with that of La_0.683(Ti_0.95Al_0.05)O₃, which has the highest ionic conductivity among the La-(Ti,Al)-O perovskite compounds.     

Titanium Incorporation in Zn2TiO4 Spinel Ceramics

Compositions in the Zn₂TiO₄+ x TiO₂ system ( x = 0–0.43) were synthesized via the solid-state reaction route, using high-purity (≥99.99%) metal-oxide powders. The incorporation of titanium, in the form of TiO₂, in Zn₂TiO₄ spinel ceramics was investigated by analyzing the crystal structure and measuring the dielectric properties. The results of the crystal structure analyses suggested that TiO₂ levels of x ≤ 0.33 could be incorporated into the Zn₂TiO₄ spinel at temperatures of T > 945°C, whereas the solid solubility of titanium in Zn₂TiO₄ decreased for T < 945°C. When x ≥ 0.28, the Zn₂Ti₃O₈ phase formed in the Zn₂TiO₄ grain interior while cooling after heat treatment. Measurement of the microwave dielectric properties also supported the conclusion that the solubility limit of titanium in Zn₂TiO₄ was close to x = 0.33, as determined through analysis of the crystal structure.     

Microwave Dielectric Properties of Li2TiO3 Ceramics Doped with ZnO–B2O3 Frit

A type of new low sintering temperature ceramic, Li₂TiO₃ ceramic, has been found. Although it is difficult for the Li₂TiO₃ compound to be sintered compactly at temperatures above 1000°C for the volatilization of Li₂O, dense Li₂TiO₃ ceramics were obtained by conventional solid-state reaction method at the sintering temperature of 900°C with the addition of ZnO–B₂O₃ frit. The sintering behavior and microwave dielectric properties of Li₂TiO₃ ceramics with less ZnO–B₂O₃ frit (≤3.0 wt%) doping were investigated. The addition of ZnO–B₂O₃ frit can lower the sintering temperature of the Li₂TiO₃ ceramics, but it does not apparently degrade the microwave dielectric properties of the Li₂TiO₃ ceramics. Typically, the good microwave dielectric properties of ɛ_r=23.06, Q × f =32 275 GHz, τ_f = 35.79 ppm/°C were obtained for 2.5 wt% ZnO–B₂O₃ frit-doped Li₂TiO₃ ceramics sintered at 900°C for 2 h. The porosity was 0.08%. The Li₂TiO₃ ceramic system may be a promising candidate for low-temperature cofired ceramics applications.     

Mesoscale Organization of Flower-Like La2O2CO3and La2O3 Microspheres

Well-dispersed spherical lanthanum oxycarbonate (La₂O₂CO₃) and La₂O₃ particles with a flower-like morphology were synthesized via a simultaneous polymerization–precipitate reaction, metamorphic reconstruction, and mineralization under a hydrothermal condition as well as subsequent calcination. The La₂O₂CO₃ and La₂O₃ microspheres obtained consist of about 20 or 40 nm thick nanosheets as petals, respectively. They have an open three-dimensional mesoporous and hollow structure and possess a high surface area, large pore volume, and marked thermal stability. These novel porous structural lanthanum-based materials could be used as catalyst supports for many reactions.     

Microstructure Characterization of the (1−x)La2/3TiO3·xLaAlO3 System

Microstructural characterizations on the (1− x )La_2/3TiO₃· x LaAlO₃ (LTLA) system were conducted using transmission electron microscopy. The presence of La₂Ti₂O₇ and La₄Ti₉O₂₄ phases in pure La_2/3TiO₃ is confirmed by the electron diffraction pattern. When x = 0.1, the ordering due to the A-site vacancies could be confirmed by the presence of antiphase boundaries (APBs) and return ½(100) superlattice reflection. As x increases, the ordering decreases and finally disappears when x = 0.6. The tilting of oxygen octahedra could be demonstrated by the presence of the ferroelastic domains in the matrix and return ½(111) and return ½(110) superlattice reflections in selected area electron diffraction patterns. In pure LaAlO₃, only the antiphase tilting of oxygen octahedra is present due to the presence of return ½(111) superlattice reflection. In the LTLA system of x = 0.1, both the antiphase and in-phase tiltings of the oxygen octahedra are involved; however, in the range of x from 0.3 to 0.9, the antiphase tilting of oxygen octahedra has appeared. The growth of the ferroelastic domains is influenced by the APBs in the matrix.     

The Optical Properties and Band Gap Energy of Nanocrystalline La0.4Sr0.6TiO3 Thin Films

The effects of microstructure on the optical properties of La_0.4Sr_0.6TiO₃ thin films were investigated. Dense films with the thickness of ∼200 nm and grain size 14–30 nm were produced on monocrystalline sapphire substrates by using a polymeric precursor spin coating technique at annealing temperatures under 800°C. X-ray data showed the formation of a single-phase cubic perovskite-type structure similar to undoped SrTiO₃ for annealing temperatures >500°C. The results of optical measurements showed that the optical spectra varied with the change of the grain size. From these data, the absorption coefficients were calculated and the band gap energy determined. In agreement with the quantum confinement model, it was shown that the band gap energy increased as the grain size decreased.     

High-Temperature Creep of Y2O3-Stabilized ZrO2

The compression creep behavior of Y₂O₃-stabilized ZrO₂ (YSZ) was studied at temperatures to 2000 ° C. The function of Y₂O₃ content and grain size was tested in specimens with various impurity concentrations and porosity distributions. For relatively fine-grained specimens, creep rates increased with the 1.5 power of the applied stress at low stresses and with the third power at high stresses. The results for coarse-grained specimens can, in general, be fit by the cube dependence. The 1.5 power can be reduced to a linear dependence by correcting for an apparent threshold stress, which decreases with increasing temperature. Creep activation energies for YSZ are 128 ± 10 kcal/mol, independent of Y₂O₃ content, impurity level, grain size, and porosity distribution. In addition, over a broad range of temperatures and stresses the absolute values of the steady-state creep rates are influenced only by grain size and O₂ partial pressure.     

Effect of Powder Coating on Stabilizer Distribution in CeO2-Stabilized ZrO2 Ceramics

The phase and microstructure relationship of 12 mol% CeO₂-stabilized ZrO₂ ceramics prepared from coated powder was investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy-dispersed X-ray spectroscopy (EDS). As compared with the sample prepared with co-precipitated method, which exhibited a similar grain size distribution, the EDS analysis revealed that the powder coating induced a wide distribution of CeO₂ solubility, which decreases monotonically with the increase of grain size. This variation of stabilizer content from grain to grain rendered many large grains in the monoclinic phase. Stronger cerium segregation to grain boundaries was observed between large grains, which often form thin amorphous films there. The inhomogeneous CeO₂ distribution keeps more tetragonal ZrO₂ grains close to the phase boundary to facilitate the transforming toughness. Addition of an Al₂O₃ precursor in coated powders effectively raises the overall CeO₂ stabilizer content in the grains and preserves more transformable tetragonal phase in the microstructure, which further enhanced the fracture toughness. The dependence of CeO₂ solubility on grain size may be explained in a simple coating-controlled diffusion and growth process that deserves further investigation.     

Crystal Structure Refinement of La0.683(Ti0.95Al0.05)O3 Perovskite by the Rietveld Method

The structural parameters of orthorhombic and tetragonal phases (space group P / mmm and P 4/ mmm ) of A-site deficient La_0.683(Ti_0.95Al_0.05)O₃ perovskite have been refined by Rietveld analysis through the X-ray powder diffraction patterns measured in the temperature range from 15° to 500°C. With an increase in temperature the unit-cell parameters a , b , and c increased, while the b / a ratio decreased and became unity between 200° and 400°C. No significant changes were observed for atomic coordinates throughout the temperature studied. These results strongly suggest that the phase transition is induced by lattice distortion.     

Crack Resistance and Fatigue of Transforming Ceramics: II, CeO2-Stabilized Tetragonal ZrO2

Crack resistance characteristics and fatigue properties have been investigated in Ce-TZP ceramics with different grain sizes. The relatively low critical transformation stress allows the development of larger transformation zones (≦200 μm), leading to flaw-tolerant behavior. However, autocatalytic transformation processes are found to be bound to grain sizes beyond a critical value; transformation is then very limited in finer microstructures. Fatigue as a specific cyclic effect is more pronounced in microstructures with larger grains. Thus, damaging processes in the course of extensive t–m transformation are suspected to be intensified during cyclic loading.     

Chemical Solution Deposition of Transparent and Metallic La0.5Sr0.5TiO3+x/2 Films Using Topotactic Reduction

Metallic and transparent La_0.5Sr_0.5TiO_{3+ x /2} films were prepared by the chemical solution deposition (CSD) method using topotactic reduction processing. The use of Si powder as the reducing agent was facile and allowed easy manipulation. It was observed that metallic (resistivity at 300 K ∼2.43 mΩ cm) and transparent (∼80% transmittance at visible light) La_0.5Sr_0.5TiO_{3+ x /2} films could be obtained with an annealing temperature of 900°C, which was significantly lower than the hydrogen reduction temperature (∼1400°C). The successful preparation of metallic and transparent La_0.5Sr_0.5TiO_{3+ x /2} films using CSD has provided a feasible route for depositing other perovskite-structured functional layers on La_0.5Sr_0.5TiO_{3+ x /2} films using this low-cost all CSD method.     

Al2TiO5-ZrTiO4-ZrO2 Composites: A New Family of Low-Thermal-Expansion Ceramics

The characterization and properties of ceramic composites containing the phases Al₂TiO₅, ZrTiO₄, and ZrO₂ are described. The range of compositions investigated gives very low average thermal expansions (α_24–1000°C as low as −2.0 × 10⁻⁶°C⁻¹) and excellent high-temperature stability. The low thermal expansions are apparently due to a combination of microcracking by the titanate phases and a contractive phase transformation by the ZrO₂. The crystal chemistry and microstructure of the product are processing dependent. Although the composites represent a complex microcracking system, the low thermal expansions and high-temperature stability make them potential candidates for commercial applications requiring thermal shock resistance.     

Effects of B2O3 Addition on the Dielectric and Ferroelectric Properties of Ba0.7Sr0.3TiO3 Ceramics

The effects of B₂O₃ addition on the sintering behavior and the dielectric and ferroelectric properties of Ba_0.7Sr_0.3TiO₃ (BST) ceramics were investigated. The dielectric and ferroelectric properties of a BST sample with 0.5 wt% B₂O₃ sintered at <1150°C were as good as those of undoped BST sintered at 1350°C, and the dielectric loss was better. When >1.0 wt% B₂O₃ was added to BST, the overdoped B₂O₃ did not form a liquid phase or volatilize; it remained in the samples and formed a secondary phase that lowered the sintering behavior and the dielectric and ferroelectric properties of the BST.     

Structure Sequence in the CaTiO3–LaAlO3 Microwave Ceramics—Revised

The composition-induced crystal structure transformations in the (1− x )CaTiO₃– x LaAlO₃ microwave ceramics were studied by X-ray powder diffraction. Increasing LaAlO₃ content results in two-phase transitions: Pnma → Imma (0.4< x <0.5) and Imma → R 3 c (0.5< x <0.6), which are related to changes of the octahedral tilting: a ⁻ b ⁺ a ⁻→ a ⁻ b ⁰ a ⁻ and a ⁻ b ⁰ a ⁻→ a ⁻ a ⁻ a ⁻, respectively. The compositional variation of the parameters of the primitive perovskite unit cell is consistent with a continuous character of the Pnma → Imma phase transition. In the case of the Imma → R 3 c crossover, a discontinuity in the variation is observed.     

The Structure and Dielectric Tunable Properties of Fine-Grained Ba0.6Sr0.4TiO3 Ceramics Prepared by Spark Plasma Sintering

Barium strontium titanate is a promising material for microwave-phased array applications. ^1,2 In this study, highly dense and fine-grained Ba_0.6Sr_0.4TiO₃ ceramics were prepared using the spark plasma sintering (SPS) technique. The structure and dielectric tunable properties of the samples were investigated. The "distorted nano-region" emerged in the interior of the grains of SPS samples, and resulted in the deterioration of the dielectric tunable properties of Ba _x Sr_{1− x} TiO₃. This phenomenon indirectly testified to the assumption of the "polar nano-region" mechanism. After the SPS samples were annealed, the "distorted nano-region" disappeared and better dielectric tunable properties were obtained. The dielectric constant was decreased to 1048, and the K value (Commutation Quality Factor) reached 7089.     

Fabrication of Na0.5Bi0.5TiO3–BaTiO3-Textured Ceramics Templated by Plate-Like Na0.5Bi0.5TiO3 Particles

Textured 0.94Na_0.5Bi_0.5TiO₃–0.06BaTiO₃ (NBT–6BT) ceramics were fabricated by templated grain growth (TGG) using anisotropically shaped Na_0.5Bi_0.5TiO₃ (NBT) templates. Platelet NBT was synthesized by the topochemical technique, using precursor Na_0.5Bi_4.5Ti₄O₁₅ (NBIT). The NBT particles have an average length of 10–15 μm and a thickness of 1 μm, which are suitable templates for obtaining textured ceramics (especially NBT-based ceramics) by the TGG process. This study revealed that the NBT templates are effective in inducing grain orientation in NBT–6BT ceramics. For NBT–6BT ceramics textured with 5 vol% NBT templates, a Lotgering factor of 0.87 and a d ₃₃ of 299 pC/N are given.