Influence of isovalent and heterovalent substitution for Bi<Superscript>3+</Superscript> and Fe<Superscript>3+</Superscript> on the properties of Bi<Subscript>2</Subscript>Fe<Subscript>4</Subscript>O<Subscript>9</Subscript>-based solid solutions

Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites have been prepared by solid-state reactions at a temperature of 1073 K. X-ray diffraction data indicate that, in the Bi_2–хLa_хFe₄O₉ system, the limiting degree of La³⁺ substitution for Bi³⁺ ions in Bi₂Fe₄O₉ does not exceed 0.05 and that the limiting degree of substitution in the Bi₂Fe_4–2xTi_xCo_xO₉ system lies in the range 0.05 < x < 0.1. The specific magnetization and specific magnetic susceptibility of the samples have been measured at temperatures from 5 to 300 K in a magnetic field of 0.86 T. The field dependences of magnetization obtained for the Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites at temperatures of 300 and 5 K demonstrate that partial isovalent substitution of La³⁺ for Bi³⁺ ions in Bi₂Fe₄O₉ and heterovalent substitution of Ti⁴⁺ and Co²⁺ ions for two Fe³⁺ ions leads to partial breakdown of the antiferromagnetic state and nucleation of a ferromagnetic state.     

Enhanced magnetoelectric coupling in La-modified Bi<Subscript>5</Subscript>Co<Subscript>0.5</Subscript>Fe<Subscript>0.5</Subscript>Ti<Subscript>3</Subscript>O<Subscript>15</Subscript> multiferroic ceramics

Multiferroic properties of La-modified four-layered perovskite Bi_5?x La _x Fe_0.5Co_0.5Ti₃O₁₅ (0 ≤ x ≤ 1) ceramics were investigated, by analyzing the magnetodielectric effect, magneto-polarization response and magnetoelectric conversion. X-ray diffraction indicated the formation of pure Aurivillius ceramics, and Raman spectroscopy revealed the Bi ions displacement and the crystal structure variation. The enhancement of ferromagnetic and ferroelectric properties was observed in Bi_5?x La _x Fe_0.5Co_0.5Ti₃O₁₅ after La modification. The evidence for enhanced ME coupling was determined by magnetic field-induced marked variations in the dielectric constant and polarization. A maximum ME coefficient of 1.15 mV/cm·Oe was achieved in Bi_4.25La_0.75Fe_0.5Co_0.5Ti₃O₁₅ ceramic, which provides the possible promise for novel magnetoelectric device application.     

Growth and properties of LiCu<Subscript>2</Subscript>O<Subscript>2</Subscript>-NaCu<Subscript>2</Subscript>O<Subscript>2</Subscript> crystals

Platelike Li_{1 ? x} Na _x Cu₂O₂ single crystals up to 2 × 10 × 10 mm in dimensions have been grown by slowly cooling (1 ? x)Li₂CO₃·xNa₂O₂·4CuO melts in alundum crucibles in air. Li_{1 ? x} Na _x Cu₂O₂ solid solutions in the LiCu₂O₂-NaCu₂O₂ system have been shown to exist in the composition range 0.78 < x < 1. The temperature stability ranges of NaCu₂O₂ and LiCu₂O₂ are 780–930 and 890–1050°C, respectively. The Mössbauer spectra and electrical conductivity of the crystals have been measured.     

Investigation on the stability of Li<Subscript>5</Subscript>La<Subscript>3</Subscript>Ta<Subscript>2</Subscript>O<Subscript>12</Subscript> lithium ionic conductors in humid environment

In this paper, the stability in humid air of Li₅La₃Ta₂O₁₂ lithium ionic conductors synthesized by conventional solid-state reaction was investigated by internal friction, conductivity, weight variation, X-ray diffraction, and thermogravimetric analysis methods. It was found that when the Li₅La₃Ta₂O₁₂ samples were aged in open air at room temperature, the internal friction peaks associated with the short-distance diffusion of lithium vacancies gradually shift toward higher temperature and increase in height, while the weight of the sample increases and impurity phases of LiOH·H₂O appear. These results reveal that the Li₅La₃Ta₂O₁₂ compounds are unstable against moisture in open air at room temperature. It was suggested that the protons from the moisture substitute the lithium ions in Li₅La₃Ta₂O₁₂ samples to form Li₂O and new protonic derivatives, Li_5?x La₃Ta₂O_12?x (OH) _x (0<x<2.15), and the resultant Li₂O may react further with water to form LiOH·H₂O.     

Effect of Bi and Sr doping on morphological and magnetic properties of LaCo<Subscript>0.6</Subscript>Fe<Subscript>0.4</Subscript>O<Subscript>3</Subscript> nanosized perovskites

Nanopowders of La _1?x Bi _x Co_0.6Fe_0.4O₃ (x = 0, 0.1, 0.2) and La _1?2x Bi _x Sr _x Co_0.6Fe_0.4O₃ (x = 0.1) multinary perovskites were synthesized by citrate sol–gel autocombustion method. Crystalline phase and the lattice parameters were obtained from X-ray diffraction pattern. The XRD result shows that all compounds have rhombhohedral crystal structure with \(\bar {\mathbf {R}\mathbf {3}}\)c space group and Bi (x = 0.2) have the presence of secondary peaks. Crystallite size, dislocation density, specific area and strain were calculated from XRD. The elemental composition and micrographs of grain were obtained from EDAX (energy dispersive X-ray analysis) and SEM (scanning electron microscopy), with an average grain size below 400 nm. Surface morphological studies using XPS (X-ray photoelectron spectroscopy) were used to find out the chemical states and surface proportion of oxygen present in samples. Finally, using the vibrating sample magnetometer the room temperature magnetic behaviour of compounds was studied and it was observed that the ferromagnetic behaviour of LaCo_0.6Fe_0.4O₃ was reduced by Bi and Sr doping.     

Structural and dielectric properties of PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript>-PbZrO<Subscript>3</Subscript> solid solutions synthesized at high pressures and temperatures

(1 ? x)PbMg_1/3Nb_2/3O₃ · xPbZrO₃ (1 ? x)PMN · xPZ) solid solutions have been synthesized at a pressure of 5 GPa and temperatures from 1300 to 1700 K, and their structural and dielectric properties have been studied. The composition dependences of the average unit-cell parameter and dielectric permittivity for the solid solutions indicate that the PMN-PZ system has a morphotropic phase boundary near x = 0.65. The solid solutions have a cubic structure for x < 0.65, a rhombohedral structure in the range 0.65 < x < 0.9, and an orthorhombic structure (similar to that of PbZrO₃) for x > 0.9. The temperature and frequency dependences of dielectric permittivity suggest that the (1 ? x)PMN · xPZ samples with x < 0.65 consist of two ferroelectric phases: a relaxor with antipolar dipole order and a normal ferroelectric with a diffuse phase transition. The effect of annealing temperature on the ferroelectric state of the samples with x < 0.65 is examined. In the composition range 0.65 < x < 0.9, the samples have normal ferroelectric properties, independent of annealing temperature.     

Solid-state reactions in the system Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>

The formation mechanisms of Li _x Na_{1 ?x} Ta _y Nb_{1 ? y} O₃ perovskite solid solutions in the Li₂CO₃-Na₂CO₃-Nb₂O₅-Ta₂O₅ system have been studied by x-ray diffraction, differential thermal analysis, thermogravimetry, IR spectroscopy, and mass spectrometry at temperatures from 300 to 1100°C. The results indicate that the synthesis of Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions involves a complex sequence of consecutive and parallel solid-state reactions. An optimized synthesis procedure for Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions is proposed.     

Magnetic properties of LaInO<Subscript>3</Subscript>-based perovskite-structure photoluminescent materials doped with Nd<Superscript>3+</Superscript>, Cr<Superscript>3+</Superscript>, and Mn<Superscript>3+</Superscript> ions

Single-phase ceramic samples of La_1–xNd_xInO₃ (0.007 ≤ x ≤ 0.05), LaIn_0.99M_0.01O₃, and La_0.95Nd_0.05In_0.995M_0.005O₃ (M = Cr³⁺ and Mn³⁺) solid solutions have been prepared by solid-state reactions, and their crystal structure, magnetic field dependences of their specific magnetization at 5 and 300 K, and temperature dependences of their molar magnetic susceptibility have been studied. It has been shown that the 300-K specific magnetization of the La_1–xNd_xInO₃ (x = 0.02, 0.05), La_0.95Nd_0.05In_0.995M_0.005O₃ (M = Cr³⁺ and Mn³⁺), and LaIn_0.99Mn_0.01O₃ solid solutions increases linearly with increasing magnetic field strength up to 14 T and that the magnitude of the 300-K specific magnetization of the La_0.993Nd_0.007InO₃ and LaIn_0.99Cr_0.01O₃ solid solutions increases linearly, but they have diamagnetic magnetization. At a temperature of 5 K, the magnetization of all the indates studied here increases nonlinearly with increasing magnetic field strength, gradually approaching magnetic saturation, without, however, reaching it in a magnetic field of 14 T. In the temperature range where the Curie–Weiss law is obeyed (5–30 K), the effective magnetic moments obtained for the Nd³⁺ ion (\({\mu _{effN{d^{3 + }}}}\)) in the La_1–xNd_xInO₃ solid solutions with x = 0.007, 0.02, and 0.05 are 2.95μ_B, 3.09μ_B, and 2.75μ_B, respectively, which is well below the theoretical value \({\mu _{effN{d^{3 + }}}}\)= 3.62μ_B. The effective magnetic moments of the Cr³⁺ and Mn³⁺ ions in the LaIn_0.99Cr_0.01O₃ and LaIn_0.99Mn_0.01O₃ solid solutions are 3.87μ^B and 5.11μ^B, respectively, and differ only slightly from the theoretical values \({\mu _{effC{r^{3 + }}}}\)= 3.87μ^B and \({\mu _{effM{n^{3 + }}}}\)= 4.9μ^B.     

Phases and morphotropic regions in the PbNb<Subscript>2/3</Subscript> Mg<Subscript>1/3</Subscript>O<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> system

Ceramic samples of solid solutions (1 ? x) PbNb_2/3Mg_1/3O₃ · xPbTiO₃ (0 ≤ x ≤ 1.0, Δx = 0.0025–0.05) are prepared by the columbite method. A detailed x?T phase diagram of the system is constructed (isothermal join at 25°C), and dielectric, piezoelectric, and elastic properties are investigated. It is established that the region of the morphotropic phase transition is positioned in the range 0.28 < x ≤ 0.43 and consists of a series of narrower regions. Inside one phase (cubic, rhombohedral, tetragonal), regions are found in which a qualitative and quantitative difference in structural and electrical parameters is observed. An interpretation of the observed effects in the context of the defect structure of the objects is suggested.     

Ultralow thermal conductivity of cerium-doped Nd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> over a wide doping range

In this paper, we report an ultralow thermal conductivity and a high-temperature phase stability of the (Nd_1?x Ce _x )₂Zr₂O_7+x system over the temperature range from room temperature to 1600 °C and over a wide composition range (0.2 ≤ x ≤ 0.8), and the (Nd_1?x Ce _x )₂Zr₂O_7+x system is therefore considered a strong candidate material for the fabrication of next-generation high-temperature thermal barrier coatings. The observed thermal conductivities (0.65–1.0 W/mK) are about 60–40% lower than those of undoped Nd₂Zr₂O₇ over the same temperature range (100–700 °C) and indicate a glass-like behavior. For comparison, the variation in the thermal conductivity with the temperature of the (Gd_1?x Ce _x )₂Zr₂O_7+x system with similar point defects was also measured, and the observed behavior was almost the same as that of undoped Gd₂Zr₂O₇ and was mostly determined by phonon–phonon scattering (λ ∝ 1/T). The effect of point defect scattering and strong phonon scattering sources (rattlers) on the thermal conductivity is also discussed in this paper. The results of this study suggest that the ultralow thermal conductivity of (Nd_1?x Ce _x )₂Zr₂O_7+x can be attributed to the presence of rattlers because of the large difference between the ionic radii of the Nd³⁺ and Ce⁴⁺ ions.     

Effect of Ni<Superscript>2+</Superscript> substitution on crystal structure and microwave dielectric properties for MgZrNb<Subscript>2</Subscript>O<Subscript>8</Subscript> ceramics

Monoclinic structured Mg_1?xNi_xZrNb₂O₈ (0?≤?x?≤?0.12) ceramics were synthesized for the first time through traditional solid-state reaction process and pure phase were obtained in all range. Rietveld refinement was used to analyze the crystal structure. With the increase of Ni²⁺ substitution amount, ε _r decreased, Q?×?f rose first then fell, τ _f shifted for the positive direction. Bond ionicity, lattice energy and bond energy were separately calculated to investigate the correlations with microwave dielectric properties. Typically, ceramics samples with the composition of Mg_0.92Ni_0.08ZrNb₂O₈ sintered at 1280 °C for 4 h exhibited the optimum microwave dielectric properties: ε _r ?=?24.58, Q?×?f?=?74534.1 GHz, τ _f ?=???49.11 ppm/°C, which could be a promising material for application.     

The magnetic properties of BiY<Subscript>2</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> nanoparticles doped with Cr ions

BiY₂Cr _x Fe_5?x O₁₂ (x = 0, 0.05, 0.1, 0.2, 0.3) nanocrystals were synthesized by using a sol-gel method. Samples were characterized by the powder X-ray diffraction (XRD), the thermal gravity analysis (TGA) and the differential thermal analysis (DTA), the vibrating sample magnetometer(VSM) and Mössbauer spectrums. The average sizes of the particles were determined by the Scherrer’s formula. The special Ms and Mössbauer spectra of BiY₂Cr _x Fe_5?x O₁₂ nanocrystals are researched at room temperature. It is seen that the special Mss of samples are initially increased with increasing Cr³⁺ content (x < 0.1), and decreased with increasing content of Cr³⁺ ions (x > 0.1).     

Influence of silver addition on microstructures and transport properties of La<Subscript>0.67</Subscript>Ca<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript>:Ag<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> composites

In order to obtain high temperature coefficient of resistance (TCR) value of La_0.67Ca_0.33MnO₃:Ag _x (LCMO:Ag _x ) composites, samples with different Ag contents (x?=?0, 0.1, 0.2, 0.25, 0.3, and 0.5) were prepared by sol–gel method. X-ray diffraction analyses indicated that all samples had orthorhombic perovskite structures. As x increased, lattice parameters (a, b, c) and cell volumes underwent slight expansions. Interestingly, the addition of Ag dramatically affected TCR and magneto-resistance (MR) values. Elevated TCR value up to 53.46%·K^?1 at 277 K was observed for LCMO:Ag _x composites with added Ag at the composition of x?=?0.1. Meanwhile, MR value at 263 K reached 71% at the magnetic field of 1 T for samples with Ag composition of x?=?0.25. The increase in Mn⁴⁺/Mn³⁺ ratio and improvement in crystallization caused by added Ag was found responsible for the elevated values of TCR, MR, and T_p. These findings may have practical use in high-performance magneto-resistive manganites.     

Strong up-conversion luminescence and electrical properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> multifunctional ceramics by Er<Superscript>3+</Superscript> doping

Novel green-emitting piezoelectric ceramics of SrBi_4?x Er _x Ti₄O₁₅ (SBT-xEr) were prepared. Strong up-conversion with bright green (524 and 548 nm) and a relatively weak red (660 nm) emission bands were obtained under 980 nm excitation at room temperature, which is attributed to the intra 4f–4f electronic transition of (²H_11/2, ⁴S_3/2)–⁴I_15/2 and the transition from ⁴F_9/2 to ⁴I_15/2 of Er³⁺ ions, respectively. Simultaneously, Er³⁺ doping promotes the electrical properties. At 0.8 mol%Er, the optimal electric properties with high Curie temperature of T _c?~527?°C, large remanent polarization of 2P _r?~14.92 μC/cm² and piezoelectric constant of d ₃₃?~17 pC/N was achieved. As a multifunctional material, Er³⁺ doped SBT showed a great potential to be used in 3D-display, bio-imaging, solid state laser and optical temperature sensor.     

Crystallization from high-temperature solutions in the K<Subscript>2</Subscript>O-P<Subscript>2</Subscript>O<Subscript>5</Subscript>-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

We have studied general trends of crystallization from high-temperature solutions in the K₂O-P₂O₅-V₂O₅-Bi₂O₃ system at P/V = 0.5?2.0, K/(P + V) = 0.7?1.4, and Bi₂O₃ contents from 25 to 50 wt % and identified the stability regions of BiPO₄, K₃Bi₅(PO₄)₆, K₂Bi₃O(PO₄)₃, and K₃Bi₂(PO₄)_{3 ? x} (VO₄) _x (x = 0?3) solid solutions. The synthesized compounds have been characterized by X-ray powder diffraction and IR spectroscopy, and the structure of two solid solutions has been determined by single-crystal X-ray diffraction (sp. gr. C ₂/c): K₃Bi₂(PO₄)₂(VO₄), a = 13.8857(8), b = 13.5432(5), c = 6.8679(4) Å, β = 114.031(7)°; K₃Bi₂(PO₄)_1.25(VO₄)_1.75, a = 13.907(4), b = 13.615(2), c = 6.956(2) Å, β = 113.52(4)°.     

Critical Behavior of La<Subscript>0.67</Subscript>Ba<Subscript>0.33</Subscript>Mn<Subscript>0.95</Subscript>Fe<Subscript>0.05</Subscript>O<Subscript>3</Subscript> Manganite

The critical behavior of perovskite manganite La_0.67Ba_0.33Mn_0.95Fe_0.05O₃ at the ferromagnetic–paramagnetic has been analyzed. The results show that the sample exhibited the second-order magnetic phase transition. The estimated critical exponents derived from the magnetic data using various such as modified d’Arrott plot Kouvel–Fisher method and critical magnetization M(T _C, H). The critical exponents values for the La_0.67Ba_0.33Mn_0.95Fe_0.05O₃ are close to those expected from the mean field model β = 0.504 ± 0.01 with T _C = 275661 ± 0.447 (from the temperature dependence of the spontaneous magnetization below T _C ), γ = 1.013 ± 0.017 with T _C = 276132 ± 0.452 (from the temperature dependence of the inverse initial susceptibility above T _C ), and δ = 3.0403 ± 0.0003. Moreover, the critical exponents also obey the single scaling equation of M(H, ε) = |ε| ^β f _±(H/|ε| ^β+γ ).     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> addition on the microstructure and electrical properties of LaMnO<Subscript>3</Subscript>-based NTC thermistors

A study to develop a new system of negative temperature coefficient thermistors for wide temperature range, A series of Mn-based perovskite-structured ceramics of composition (LaMn_1?x Al _x O₃)_0.9(Al₂O₃)_0.1 has been synthesized by conventional solid state reaction at 1350?°C. The X-ray diffraction patterns showed that for all the samples, the substitution of manganese by aluminum up to x?=?0.1 preserved the rhombohedral perovskite LaMnO₃-like phase. For x?=?0.2, apart from the LaMnO₃-like structure, a second perovskite phase based on the cubic LaAlO₃ structure was formed. For x?=?0.3 and 0.4, the phase present was LaAlO₃ -type structure. The grain sizes of the sintered body detected by scanning electron microscope were decreased with increasing Al₂O₃ content. The resistivity increases with increasing the Al content. The obtained values of ρ _25?°C and B _25/50 and E _a are in the range of 10–13103 Ω cm, 1813–2794 K, 0.156–0.241 eV, respectively. The resistance variation (ΔR/R) was <0.241% and the minimum value (0.0483%) was obtained for aging at 125?°C at 500 h. The aim of this work was explored new composite ceramics materials, which could be used as potential candidates for wide temperature range from ?100 to 500?°C thermistors applications.     

Electric-field effect on crystal growth in the Li<Subscript>3</Subscript>PO<Subscript>4</Subscript>-Li<Subscript>4</Subscript>GeO<Subscript>4</Subscript>-Li<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-LiF system

We have studied the electric-field effect on crystallization processes in the Li₃PO₄-Li₄GeO₄-Li₂MoO₄-LiF system. In zero field, Li_3+x P_1?x Ge _x O₄ (x = 0.31) crystals were grown on the cathode under the conditions of this study. At low applied voltages (≤ 0.5 V), we obtained Li₂MoO₄, Li₂GeO₃, and Li_1.3Mo₃O₈. In the range V = 0.5–1 V, crystals of Li_3+x P_1?x Ge _x O₄ solid solutions with x = 0.17, 0.25, 0.28, 0.29, and 0.36 were obtained. An applied electric field was shown to reduce the melting temperature of the starting mixtures and the crystallization onset temperature.     

Effects of Ge<Superscript>4+</Superscript> acceptor dopant on sintering and electrical properties of (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)NbO<Subscript>3</Subscript> lead-free piezoceramics

Lead-free (K_0.5Na_0.5)(Nb_1-xGe _x )O₃ (KNN-xGe, where x = 0-0.01) piezoelectric ceramics were prepared by conventional ceramic processing. The effects of Ge⁴⁺ cation doping on the phase compositions, microstructure and electrical properties of KNN ceramics were studied. SEM images show that Ge⁴⁺ cation doping improved the sintering and promoted the grain growth of the KNN ceramics. Dielectric and ferroelectric measurements proved that Ge⁴⁺ cations substituted Nb⁵⁺ ions as acceptors, and the Curie temperature (T_C) shows an almost linear decrease with increasing the Ge⁴⁺ content. Combining this result with microstructure observations and electrical measurements, it is concluded that the optimal sintering temperature for KNN-xGe ceramics was 1020°C. Ge⁴⁺ doping less than 0.4 mol.%can improve the compositional homogeneity and piezoelectric properties of KNN ceramics. The KNN-xGe ceramics with x = 0.2% exhibited the best piezoelectric properties: piezoelectric constant d₃₃ = 120 pC/N, planar electromechanical coupling coefficient k_p = 34.7%, mechanical quality factor Q_m = 130, and tanδ = 3.6%.     

Magnetization reversal and tunable exchange bias behavior in Mn-substituted NiCr<Subscript>2</Subscript>O<Subscript>4</Subscript>

Single phase samples of Ni(Cr_1?xMn _x )₂O₄ (x = 0–0.50) were synthesized by using sol–gel route. Investigation of structural, magnetic, exchange bias and magnetization reversal properties was carried out in the bulk samples of Ni(Cr_1?xMn _x )₂O₄. Rietveld refinement of the X-ray diffraction patterns recorded at room temperature reveals the tetragonal structure for x = 0 sample with I4₁/amd space group and cubic structure for x ≥ 0.05 samples with \( {\text{Fd}\bar{3}\text{m}} \) space group. Magnetization measurements show that all samples exhibit ferrimagnetic behavior, and the transition temperature (T_C) is found to increase from 73 K for x = 0 to 138 K for x = 0.50. Mn substitution induces magnetization reversal behavior especially for 30 at% of Mn in NiCr₂O₄ system with a magnetic compensation temperature of 45 K. This magnetization reversal is explained in terms of different site occupation of Mn ions and the different temperature dependence of the magnetic moments of different sublattices. Study of exchange bias behavior in x = 0.10 and 0.30 samples reveals that they exhibit negative and tunable positive and negative exchange bias behavior, respectively. The magnitudes of maximum exchange bias field of these samples are found to be 640 and 5306 Oe, respectively. Exchange bias in x = 0.10 sample originates from the anisotropic exchange interaction between the ferrimagnetic and the antiferromagnetic components of magnetic moment. The tunable exchange bias behavior in x = 0.30 sample is explained in terms of change in domination of one sublattice moment over the other as the temperature is varied.