基于PWM整流器的功率控制器的仿真研究

文章研究了一种基于PWM整流器的功率控制器。由三相电压型整流器在三相静止坐标系中的数学模型,导出其在两相旋转坐标系的数学模型,并在此基础上引入了基于电网电压前馈解耦的三相PWM整流器控制系统,实现对于有功电流和无功电流的单独控制,从而达到对于有功、无功功率控制的目的。     

Shunt active filter for reactive power compensation

A simple control technique for three-phase shunt active filters without computation of the reactive current component is presented. A current controller with fast dynamics for an active filter is described. Reactive current is directly controlled without the need for sensing and computing the reactive component of the load current, thus simplifying the control system. Current compensation is done in the time domain, allowing a fast time response. The dc voltage control loop keeps the voltage across the dc capacitor constant. High power factor control by an active filter is described. All control functions are implemented in software using a singlechip microcontroller, thus simplifying the control circuit. Any current-controlled synchronous rectifier can be used as a shunt active filter through only the simple modification of the software and the addition of current sensors. It is shown through experimental results that the proposed controller gives good performance for the shunt active filter.     

A novel high-performance voltage regulator for single-phase ACsources

Regulation of load voltage in single-phase applications is becoming an important issue for critical loads. This paper presents a novel high-performance single-phase voltage regulator which has a common arm between the rectifier and inverter, and adopts an appropriate switching strategy. The proposed voltage regulator employs six switches and can be implemented by only one three-phase inverter module. The proposed voltage regulator has the capability of delivering sinusoidal input current with unity power factor, good output voltage regulation, and bidirectional power flow. For these purposes, a fully digital controller is designed and implemented using a TMS320F240 digital signal processor. In addition, a novel low-cost AC capacitor is also presented. This type of capacitor requires two DC capacitors and two diodes, enabling low-cost and compact manufacturing. Consequently, the complete voltage regulator system, which is mainly suitable for an uninterruptible power supply as well as reactive or nonlinear loads, can be constructed compactly and inexpensively. Experimental results are presented to verify the feasibility of the proposed voltage regulator system     

State variable decoupling and power flow control in PWMcurrent-source rectifiers

Pulsewidth modulated (PWM) current-source rectifiers (CSR), among other alternatives, offer marked improvements over thyristor line-commutated rectifiers as a source of variable DC power. Advantages include reduced line current harmonic distortion and complete displacement power factor control, including unity displacement power factor operation. However, due to nonlinearities of the PWM-CSR model, their control has usually been carried out using direct line current control in a three-phase stationary frame (abc). This paper proposes the application of a nonlinear control technique that introduces more flexibility in the control of the rectifier and results in a more straightforward approach to controller design. The proposed technique is based on a nonlinear state variable feedback approach in the rotating frame (dq). The approach allows the independent control of the two components of the line current (active and reactive) with the same dynamic performance, regardless of the operating point. The control strategy also eliminates the need for input damping resistors and rejects the effect of supply voltage variations. Furthermore, a space vector modulation (SVM) technique is used to maximize the supply voltage utilization. This paper includes a complete formulation of the system equations and a controller design procedure. Experimental results on a 2 kVA digital-signal-processor-controlled prototype confirm the validity of theoretical considerations     

Single-stage three-phase boost power factor correction circuit for AC–DC converter

This article presents a single-stage three-phase power factor correction (PFC) circuit for AC-to-DC converter using a single-switch boost regulator, leading to improve the input power factor (PF), reducing the input current harmonics and decreasing the number of required active switches. A novel PFC control strategy which is characterised as a simple and low-cost control circuit was adopted, for achieving a good dynamic performance, unity input PF, and minimising the harmonic contents of the input current, at which it can be applied to low/medium power converters. A detailed analytical, simulation and experimental studies were therefore conducted. The effectiveness of the proposed controller algorithm is validated by the simulation results, which were carried out using MATLAB/SIMULINK environment. The proposed system is built and tested in the laboratory using DSP-DS1104 digital control board for an inductive load. The results revealed that the total harmonic distortion in the supply current was very low. Finally, a good agreement between simulation and experimental results was achieved.     

Parallel Connection of Two Three-Phase Three-Switch Buck-Type Unity-Power-Factor Rectifier Systems With DC-Link Current Balancing

Connecting three-phase rectifier systems in parallel shows many advantages as compared to a single rectifier system with higher output power, such as higher reliability, smaller current and voltage ripple components, lower filtering effort, or higher system bandwidth. However, current unbalance or circulating currents can occur for modular design. In this paper, the parallel connection of two three-phase three-switch buck-type unity-power-factor pulsewidth-modulation rectifier systems is experimentally investigated for a 10-kW digital-signal-processor-controlled prototype. A space vector modulation scheme is employed showing all the advantages of an interleaved operation. Three control schemes for active dc-link current balancing are described employing an additional free-wheeling state that allows to influence the rate of change of the dc-link currents and can therefore be used for dc-link current balancing. The control schemes differ concerning control action and additional switching losses. Simulation and experimental results confirm the theoretical considerations: The dc-link current-balancing capability of the different control methods is compared, and the influence of the additional free-wheeling state on switching losses and operation behavior is investigated. The most advantageous control method, which employs a hysteresis controller and shows limited switching losses, is selected. The analysis of the mains behavior shows an improvement as compared to a single rectifier operation.     

单周期控制三相VIENNA整流器

电网谐波污染已经引起世界各国的高度重视,功率因数校正（PFC）是治理谐波的一种有效方法。文章对基于单周期控制的三相VIENNA整流器进行了研究,推导了单周期控制三相VIENNA整流器的控制规律,与其它控制方案相比不需要乘法器,不需对电源电压进行检测,控制逻辑比较简单并且以恒定开关频率工作,能够实现单位功率因数校正和低电流畸变。仿真结果验证了理论分析的正确性。     

A Model-Based Direct Power Control for Three-Phase Power Converters

The direct power control (DPC) technique has been widely used as a control strategy for three-phase power rectifiers due to its simplicity and good performance. DPC uses the instantaneous active and reactive power to control the power converter. The controller design has been proposed as a direct control with a lookup table and, in recent works, as an indirect control with an inner control loop with proportional-plus-integral controllers for the instantaneous active and reactive power errors. In this paper, a model-based DPC for three-phase power converters is designed, obtaining expressions for the input control signal, which allow the design of an adaptive control law that minimizes the errors introduced by parameter uncertainties as the smoothing inductor value or the grid frequency. A controller design process, a stability study of the system, and experimental results for a synchronous three-phase power rectifier prototype are presented to validate the proposed controller.     

Digital-signal-processor-based control of three-phase space vectormodulated converters

The paper presents the implementation of a DSP-based controller for three-phase, space-vector modulated converters. The implementation is illustrated for the control of a 2 kW, ZVS matrix power converter-based three-phase PWM rectifier. The controller features very high data processing speed (converter switching frequency of 100 kHz), and provides high-quality, low-distortion power converter input currents and output voltages. The controller can be implemented using only a few standard integrated circuits, providing high reliability and low cost     

采用pq瞬时功率理论的三相电压源变换器的研究

瞬时有功和无功功率理论,即Pq瞬时功率理论,得到了广泛的研究和实际应用。本文基于pq瞬时功率理论,分析了三相有源电力滤波器三种主要控制策略的工作原理,包括瞬时功率恒定策略、电流波形正弦策略、广义Fryze电流控制策略,另外简要分析了三相有源电力滤波器的另一种同步功率传输控制策略,并在三相供电电压平衡和对称的条件下,将pq瞬时功率理论应用到三相电压源PWM整流器中,采用MATLAB/SIMULINK进行较为深入的仿真分析,获得了非常满意的结果。结果表明,相比平均功率理论,采用pq瞬时功率理论,三相电压源变换器具有响应快、控制简单等优点。     

A passive series, active shunt filter for high power applications

This paper presents a hybrid series passive/shunt active power filter system for high power nonlinear loads. This work is motivated by the fact that the ability of a converter to perform effectively as an active filter is limited by the power and the frequency distribution of the distortion for which it must compensate. This system is comprised of a three-phase shunt active filter and series AC line smoothing reactance installed in front of the target load. The proposed system significantly reduces the required shunt active filter bandwidth. The space-vector pulse width modulation (PWM) controller is based on a dead-beat control model. It is implemented digitally using a single 16-bit microcontroller. This controller requires only the supply current to be monitored, an approach different from conventional methods. The paper provides background on the operation of the filter, the details of the power circuit, the details of the control design, representative waveforms, and spectral performance for a filter which supports a 15 kVA phase controlled rectifier load. Experimental data indicate that the active filter typically consumes 2% or less of the average load power, suggesting that a parallel filter is an efficient compensation approach. The spectral performance shows that the active filter brings the system into compliance with IEEE519-1992 up to the 33rd harmonic for an AC line smoothing reactance of 0.13 p.u     

Three-phase single-stage four-switch PFC buck-boost-type rectifier

This paper proposes a new three-phase single-stage power-factor corrector buck-boost-type rectifier topology. The typical topology uses a bridge configuration with six switches. This new topology only requires four switches, improving the rectifier efficiency as only one reverse-blocking power semiconductor conducts at any time. A vector-based sliding-mode control method for the three-phase input currents is also proposed. This fast and robust technique uses sliding mode to generate /spl alpha//spl beta/ space-vector modulation, which forces the input line currents to track a suitable sinusoidal reference. A near-unity power-factor operation of the rectifier is obtained using a sinusoidal reference in phase with the input source voltages. A proportional-integral controller is adopted to regulate the output voltage of the converter. This external voltage controller modulates the amplitude of the current references. The characteristics of the new rectifier are verified with experimental results.     

三相三开关部分有源功率因数校正电路的研究

三相交流电源供电的较大功率变频空调日益得到广泛应用,带来了三相整流器的功率校F问题。在简要分析三相单开关部分有源PFC的基础上,根据三相三线制、三相四线制供电方式的不同,提出了两种结合有源PFC技术和无源PFC技术的Buck型混合三相有源部分PFC方案,在对其工作原理进行简要分析和仿真分析的基础上,进行了实验研究,所得结果验证了所提出的三相部分PFC具有电压与电流应力小、效率高、功率因数高、直流平均电压较高的特点,各种负载下交流输入侧的各次谐波电流均满足IEC61000-3-2标准,中等负载以上时输入功率因数高达0.98。     

Analysis of the Instantaneous Power Flow for Three-Phase PWM Boost Rectifier Under Unbalanced Supply Voltage Conditions

This paper proposes the analysis of the instantaneous power flow of three-phase pulse-width modulation (PWM) boost rectifier under unbalanced supply voltage conditions. An analytical expression for the instantaneous output power has been derived, which provides the link between the output dc link voltage and the instantaneous output power. A direct relationship between the dc link voltage ripples and the second harmonic component in the instantaneous output power has been established. Based on the input and output instantaneous power analytical expressions provided, the presence of the odd order harmonic components in the ac line currents can be explained. A simple cascaded PI control scheme has been developed for the dc output voltage control. The controller ensures that the dc link voltage is maintained constant and the supply side power factor is kept close to unity under the unbalanced supply voltage operating conditions. Simulation and experimental test results are provided on a 1.6-kVA laboratory-based PWM rectifier to validate the proposed analysis and control scheme.      

单周期控制三相电压型PWM整流器

文章对基于单周期控制的三相PWM高功率因数整流器进行了研究,推导了单周期控制三相电压型PWM整流器的控制规律。它不需要乘法器更不需要对输入电压进行检测,其控制逻辑简单并且以恒定频率工作,可以在每个开关周期控制输入电流跟踪正弦参考量,从而实现低电流谐波畸变和高功率因数。基于Multisim2001软件平台,建立了基于单周期控制的三相电压型PWM整流器的仿真模型,完成了6kW三相PWM整流器的设计和实验研究,仿真和试验结果都验证了理论分析的正确性。     

A novel three-phase utility interface minimizing line currentharmonics of high-power telecommunications rectifier modules

Based on the combination of a three-phase diode bridge and a DC/DC boost converter, a new three-phase three-switch three-level pulsewidth modulated (PWM) rectifier system is developed. It can be characterized by sinusoidal mains current consumption, controlled output voltage, and low-blocking voltage stress on the power transistors. The application could be, e.g., for feeding the DC link of a telecommunications power supply module. The stationary operational behavior, the control of the mains currents, and the control of the output voltage are analyzed. Finally, the stresses on the system components are determined by digital simulation and compared to the stresses in a conventional six-switch two-level PWM rectifier system     

Real-time multi-DSP control of three-phase current-source unitypower factor PWM rectifier

The design of a real-time multi-DSP controller for a high-quality six-valve, three-phase current-source unity power factor pulse-width-modulated (PWM) rectifier is discussed. With the decoupler preprocessor and the dynamic trilogic PWM trigger scheme, each of the three input currents can be controlled independently. The pole-placement control method implemented, which is based on the a-b- c frame system model and fast parallel computer control, achieves fast AC current response. The low-frequency resonance in the AC filter L-C networks is damped effectively. The experimental results were obtained for a 1 kVA bipolar transistor current-source PWM rectifier with a real-time controller using three TMS320C25 DSPs     

Operating a three-phase diode rectifier with a low-input currentdistortion using a series-connected dual boost converter

This paper describes a technique for shaping the input current to a three-phase diode rectifier using a two-switch series-connected dual boost converter and a three-phase bidirectional switch circuit. Circuits are described for generating a single voltage DC output, “single DC-rail”, or a dual output DC voltage using center-tapped capacitors, “split DC-rail”. Both rectifier types can be operated with the boost inductors located either on the DC or the AC side of the rectifier. The resultant rectifier circuit configurations have an excellent immunity to the “shoot-through” fault condition and use active switching elements with low per-unit current ratings and low switching losses. These features increase the reliability factor and lower the cost penalty associated with unity fundamental power factor three-phase rectifiers. Test results are presented for the rectifiers using simulation and experimental results     

Three-phase switch mode rectifier with hysteresis current control

A three-phase configuration of a switch mode rectifier (SMR) that makes use of continuous conduction waveform of the input supply current is suggested. Continuous conduction is achieved by the hysteresis current control (HCC) technique. This three-phase SMR operates at close to unity power factor and has reduced current stresses on the switching devices because of the continuous nature of input current. The conduction period considered for the rectifier diodes is 180°. Digitally simulated performance results are provided. Selected experimental results demonstrating the SMR operation are also presented     

A Simple Control Method for a Switching Rectifier with Power Transistors

A very simple control method for a high-frequency switching rectifier with power transistors is presented. The converter uses six semiconductor switches with turn-off capability to connect directly the three-phase source to the load. Each semiconductor switch is composed by two power MOSFET transistors. The control method is based on the fictitious bipolar source concept. A two-level controller with hysteresis is used to control the load current. The converter accepts power flow in both directions, does not need large storage elements, works with good power factor, and can generate output frequencies higher than the source frequency, without affecting the quality of the output current. The control and logic circuits of the rectifier are very simple, due to the high controllability of the bidirectional switches. The performance of the converter is investigated experimentally in the four-quadrant speed control of a dc machine.