Voltammetric behavior and the determination of quercetin at a flowerlike Co<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles modified glassy carbon electrode

Flowerlike Co₃O₄ nanoparticles were used as a modifier on the glassy carbon electrode to fabricate a quercetin (Qu) sensor. The morphology and crystallinity of the prepared Co₃O₄ material were investigated by scanning electron microscopy and X-ray diffraction. Electrochemical behavior of Qu at the sensor was studied by cyclic voltammetry and semi-derivative voltammetry. Results suggested that the modified electrode exhibited a strong electrocatalytic activity toward the redox of Qu. The electron transfer coefficient (α), the number of electron transfer (n), and the diffusion coefficient (D) of Qu at the sensor were calculated. Under the optimum conditions, the catalytic peak currents of Qu were linearly dependent on the concentrations of Qu in the range from 5.0 × 10⁻⁷ to 3.3 × 10⁻⁴ M, with a detection limit of 1.0 × 10⁻⁷ M. This proposed method was successfully applied to determine the quercetin concentration in Ginkgo leaf tablet and human urine samples.     

Synthesis and optical property of one-dimensional spinel ZnMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanorods

Spinel zinc manganese oxide (ZnMn₂O₄) nanorods were successfully prepared using the previously synthesized α-MnO₂ nanorods by a hydrothermal method as template. The nanorods were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, UV-Vis absorption, X-ray photoelectron spectroscopy, surface photovoltage spectroscopy, and Fourier transform infrared spectroscopy. The ZnMn₂O₄ nanorods in well-formed crystallinity and phase purity appeared with the width in 50-100 nm and the length in 1.5-2 μm. They exhibited strong absorption below 500 nm with the threshold edges around 700 nm. A significant photovoltage response in the region below 400 nm could be observed for the nanorods calcined at 650 and 800°C.     

Nanocasting Synthesis of Mesostructured Co<Subscript>3</Subscript>O<Subscript>4</Subscript> via a Supercritical CO<Subscript>2</Subscript> Deposition Method and the Catalytic Performance for CO Oxidation

Abstract  

We demonstrate a supercritical CO₂ (scCO₂) deposition method to synthesize mesostructured Co₃O₄ with crystalline walls using SBA-15 as the hard template. By variation of the scCO₂ pressure, randomly organized nanorods or a highly ordered mesoporous structure of Co₃O₄ is obtained after only one filling operation. The catalytic tests show that the randomly organized Co₃O₄ nanorods display excellent activity for CO oxidation with the complete conversion of CO even at room temperature, while neither the ordered mesoporous nor bulk Co₃O₄ is active at this low-temperature, demonstrating the important role of Co₃O₄ morphology in catalysis.     

Electrochemical properties of microwave-assisted reflux-synthesized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles in different electrolytes for supercapacitor applications

The nanosized Mn₃O₄ particles were prepared by microwave-assisted reflux synthesis method. The prepared sample was characterized using various techniques such as X-ray diffraction (XRD), Fourier transform-infrared spectroscopy (FT-IR), Raman analysis, and transmission electron microscopy (TEM). Electrochemical properties of Mn₃O₄ nanoparticles were investigated using cyclic voltammogram (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge–discharge analysis in different electrolytes such as 1 M KCl, 1 M Na₂SO₄, 1 M NaNO₃, and 6 M KOH electrolytes. XRD pattern reveals the formation of single-phase Mn₃O₄ nanoparticles. The FT-IR and Raman analysis also assert the formation of Mn₃O₄ nanoparticles. The TEM image shows the spherical shape particles with less than 50 nm sizes. Among all the electrolytes, the Mn₃O₄ nanoparticles possess maximum specific capacitance of 94 F g⁻¹ in 6 M KOH electrolyte calculated from CV. The order of capacitance obtained by various electrolytes is 6 M KOH > 1 M KCl > 1 M NaNO₃ > 1 M Na₂SO₄. The EIS and galvanostatic charge–discharge results further substantiate with the CV results. The cycling stability of Mn₃O₄ electrode reveals that the prepared Mn₃O₄ nanoparticles are a suitable electrode material for supercapacitor application.     

Structural characterization and electrochemical properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> anode materials synthesized by a hydrothermal method

Cobalt oxide [Co₃O₄] anode materials were synthesized by a simple hydrothermal process, and the reaction conditions were optimized to provide good electrochemical properties. The effect of various synthetic reaction and heat treatment conditions on the structure and electrochemical properties of Co₃O₄ powder was also studied. Physical characterizations of Co₃O₄ are investigated by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller [BET] method. The BET surface area decreased with values at 131.8 m²/g, 76.1 m²/g, and 55.2 m²/g with the increasing calcination temperature at 200°C, 300°C, and 400°C, respectively. The Co₃O₄ particle calcinated at 200°C for 3 h has a higher surface area and uniform particle size distribution which may result in better sites to accommodate Li⁺ and electrical contact and to give a good electrochemical property. The cell composed of Super P as a carbon conductor shows better electrochemical properties than that composed of acetylene black. Among the samples prepared under different reaction conditions, Co₃O₄ prepared at 200°C for 10 h showed a better cycling performance than the other samples. It gave an initial discharge capacity of 1,330 mAh/g, decreased to 779 mAh/g after 10 cycles, and then showed a steady discharge capacity of 606 mAh/g after 60 cycles.     

Catalytic properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles for rechargeable Li/air batteries

Three types of Co₃O₄ nanoparticles are synthesized and characterized as a catalyst for the air electrode of a Li/air battery. The shape and size of the nanoparticles are observed using scanning electron microscopy and transmission electron microscopy analyses. The formation of the Co₃O₄ phase is confirmed by X-ray diffraction. The electrochemical property of the air electrodes containing Co₃O₄ nanoparticles is significantly associated with the shape and size of the nanoparticles. It appears that the capacity of electrodes containing villiform-type Co₃O₄ nanoparticles is superior to that of electrodes containing cube- and flower-type Co₃O₄ nanoparticles. This is probably due to the sufficient pore spaces of the villiform-type Co₃O₄ nanoparticles.     

Preparation and electrochemical performance of Li-rich layered cathode material,Li[Ni<Subscript>0.2</Subscript>Li<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>]O<Subscript>2</Subscript>, for lithium-ion batteries

The Li-rich layered cathode material, Li[Ni_0.2Li_0.2Mn_0.6]O₂, was synthesized via a “mixed oxalate” method, and its structural and electrochemical properties were compared with the same material synthesized by the sol–gel method. X-ray diffraction (XRD) shows that the synthesized powders have a layered O₃–LiCoO₂-type structure with the R-3m symmetry. X-ray photoelectron spectroscopy (XPS) indicates that in the above material, Ni and Mn exist in the oxidation states of +2 and +4, respectively. The layered material exhibits an excellent electrochemical performance. Its discharge capacity increases gradually from the initial value of 228 mA hg⁻¹ to a stable capacity of over 260 mA hg⁻¹ after the 10th cycle. It delivers a larger capacity of 258 mA hg⁻¹ at the 30th cycle. The dQ/dV curves suggest that the increasing capacity results from the redox-reaction of Mn⁴⁺/Mn³⁺.     

Chemical and electrochemical characterization of TiO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> atomic layer depositions on AZ-31 magnesium alloy

In this study, innovative TiO₂/Al₂O₃ mono/multilayers were applied by atomic layer depositions (ALD) on ASTM-AZ-31 magnesium/aluminum alloy to enhance its well-known scarce corrosion resistance. Four different configurations of ALD layers were tested: single TiO₂ layer, single Al₂O₃ layer, Al₂O₃/TiO₂ bilayer and Al₂O₃/TiO₂/Al₂O₃/TiO₂ multilayer deposited using Al[(CH₃)]₃ (trimethylaluminum, TMA), and TiCl₄ and H₂O precursors. All depositions were performed at 120°C to obtain an amorphous-like structure of both oxide layers. The four coatings were then investigated using different techniques, such as scanning electron microscope (SEM), stylus profilometer, glow discharge optical emission spectrometry (GDOES) and polarization curves in 0.05-M NaCl solution. The thickness of all the coatings was around 100 nm. The layers compositions were successfully investigated by the GDOES technique, although obtained data seem to be affected by substrate roughness and differences in sputtering rates between ceramic oxides and metallic magnesium alloy. Corrosion resistance showed to be strongly enhanced by the nanometric coatings, giving lower corrosion current densities in 0.05-M NaCl media with respect to the uncoated substrate (from 10⁻⁴ to 10⁻⁶ A/cm² for the single layers and from 10⁻⁴ to 10⁻⁸ A/cm² for the bi- and multilayers). All polarization curves on coated samples also showed a passive region, wider for the bi-layer (from −0.58 to −0.43 V with respect to Ag/AgCl) and multilayer (from −0.53 to −0.38 V with respect to Ag/AgCl) structures.     

Study of electrochemical properties and the charge/discharge mechanism for Li<Subscript>4</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript>/MnO<Subscript>2</Subscript>-AC hybrid supercapacitor

Spinel Li₄Mn₅O₁₂ was prepared by a sol–gel method. The manganese oxide and activated carbon composite (MnO₂-AC) were prepared by a method in which KMnO₄ was reduced by activated carbon (AC). The products were characterized by XRD and FTIR. The hybrid supercapacitor was fabricated with Li₄Mn₅O₁₂ and MnO₂-AC, which were used as materials of the two electrodes. The pseudocapacitance performance of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor was studied in various aqueous electrolytes. Electrochemical properties of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor were studied by using cyclic voltammetry, electrochemical impedance measurement, and galvanostatic charge/discharge tests. The results show that the hybrid supercapacitor has electrochemical capacitance performance. The charge/discharge test showed that the specific capacitance of 51.3 F g⁻¹ was obtained within potential range of 0–1.3 V at a charge/discharge current density of 100 mA g⁻¹ in 1 mol L⁻¹ Li₂SO₄ solution. The charge/discharge mechanism of Li₄Mn₅O₁₂ and MnO₂-AC was discussed.     

Synthesis and magnetic properties of single-crystalline Na<Subscript>2-</Subscript><Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript>8</Subscript>O<Subscript>16</Subscript> nanorods

The synthesis of single-crystalline hollandite-type manganese oxides Na_{2- x} Mn₈O₁₆ nanorods by a simple molten salt method is reported for the first time. The nanorods were characterized by powder X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and a superconducting quantum interference device magnetometer. The magnetic measurements indicated that the nanorods showed spin glass behavior and exchange bias effect at low temperatures. The low-temperature magnetic behaviors can be explained by the uncompensated spins on the surface of the nanorods.     

Electrochemical promotion of CO<Subscript>2</Subscript> hydrogenation on Rh/YSZ electrodes

The electrochemical promotion of the CO₂ hydrogenation reaction on porous Rh catalyst–electrodes deposited on Y₂O₃-stabilized-ZrO₂ (or YSZ), an O²⁻ conductor, was investigated under atmospheric total pressure and at temperatures 346–477 °C, combined with kinetic measurements in the temperature range 328–391 °C. Under these conditions CO₂ was transformed to CH₄ and CO. The CH₄ formation rate increased by up to 2.7 times with increasing Rh catalyst potential (electrophobic behavior) while the CO formation rate was increased by up to 1.7 times with decreasing catalyst potential (electrophilic behavior). The observed rate changes were non-faradaic, exceeding the corresponding pumping rate of oxygen ions by up to approximately 210 and 125 times for the CH₄ and CO formation reactions, respectively. The observed electrochemical promotion behavior is attributed to the induced, with increasing catalyst potential, preferential formation on the Rh surface of electron donor hydrogenated carbonylic species leading to formation of CH₄ and to the decreasing coverage of more electron acceptor carbonylic species resulting in CO formation.     

Preparation and characterization of spindle-like Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> mesoporous nanoparticles

Magnetic spindle-like Fe₃O₄ mesoporous nanoparticles with a length of 200 nm and diameter of 60 nm were successfully synthesized by reducing the spindle-like α-Fe₂O₃ NPs which were prepared by forced hydrolysis method. The obtained samples were characterized by transmission electron microscopy, powder X-ray diffraction, attenuated total reflection fourier transform infrared spectroscopy, field emission scanning electron microscopy, vibrating sample magnetometer, and nitrogen adsorption-desorption analysis techniques. The results show that α-Fe₂O₃ phase transformed into Fe₃O₄ phase after annealing in hydrogen atmosphere at 350°C. The as-prepared spindle-like Fe₃O₄ mesoporous NPs possess high Brunauer-Emmett-Teller (BET) surface area up to ca. 7.9 m² g^-1. In addition, the Fe₃O₄ NPs present higher saturation magnetization (85.2 emu g^-1) and excellent magnetic response behaviors, which have great potential applications in magnetic separation technology.     

Selective Synthesis of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanowires Via a Single Precursor: A General Method for Metal Oxide Nanowires

Hematite (α-Fe₂O₃) and magnetite (Fe₃O₄) nanowires with the diameter of about 100 nm and the length of tens of micrometers have been selectively synthesized by a microemulsion-based method in combination of the calcinations under different atmosphere. The effects of the precursors, annealing temperature, and atmosphere on the morphology and the structure of the products have been investigated. Moreover, Co₃O₄ nanowires have been fabricated to confirm the versatility of the method for metal oxide nanowires.     

Oxygen permeability and structural stability of La<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>Co<Subscript>0.2</Subscript>Fe<Subscript>0.8</Subscript>O<Subscript>3−<Emphasis Type="Italic">δ</Emphasis></Subscript> membrane

La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ oxides were synthesized by citrate method and hydrothermal method. The oxides prepared by citrate method are perovskite type structure, while the oxides by hydrothermal method have a small amount of secondary phase in the powder. Pyrex glass seal and Ag melting seal provided reliable gas-tight sealing of disk type dense membrane in the range of operation temperature, but commercial ceramic binder could not be removed from the support tube without damage to the tube or membrane. Though the degree of gas tightness increases in the order of glass>Ag>ceramic binder, in the case of glass seal, the undesired spreading of glass leads to an interfacial reaction between it and the membrane and reduction of effective permeation area. The oxygen flux of La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ membrane increases with increasing temperature and decreasing thickness, and the oxygen permeation flux through 1.0 mm membrane exposed to flowing air (P _h =0.21 atm) and helium (P₁=0.037 atm) is ca. 0.33 ml/cm²·min at 950 °C. X-ray diffraction analysis for the membrane after permeation test over 160 h revealed that La₂O₃ and unknown compound were formed on the surface of membrane. The segregation compounds of surface elements formed on both surfaces of membrane irrespective of spreading of glass sealing material. This paper was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Improved electrochemical properties of Li(Ni<Subscript>0.7</Subscript>Co<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode for lithium ion batteries with controlled sintering conditions

Improved electrochemical properties of Li(Ni_0.7Co_0.3)O₂ cathode material are reported. Samples were synthesized by the co-precipitation method with various sintering conditions, namely temperature, time and atmosphere. Li(Ni_0.7Co_0.3)O₂ sintered at 850 °C for 14 h in air exhibited the lowest unit cell volume accompanied with relatively higher values of c/a and I ₁₀₃/I ₁₀₄ reflection peaks ratios. This also exhibited superior electrochemical properties, such as high charge–discharge capacity, high Coulombic efficiency, and low irreversible capacity loss. This can be attributed to improved hexagonal ordering, crystallinity and morphology. The electrochemical cell parameters were better than the reported ones, probably due to controlled sintering conditions.     

Direct electrochemical reduction of Dy<Subscript>2</Subscript>O<Subscript>3</Subscript> in CaCl<Subscript>2</Subscript> melt

The electrochemical reduction of Dy₂O₃ in CaCl₂ melt was studied. The cyclic voltammetry, chronoamperometry, AC impedance and constant voltage electrolysis were employed. A single cathodic current peak in the cyclic voltammogram and one response semicircle in the AC impedance spectrum were observed, supporting a one-step electrochemical reduction mechanism of Dy₂O₃. No intermediates were observed by XRD, which confirmed the following electrochemical reduction sequence: Dy₂O₃ → Dy. The charge transfer resistances and the activation energies involved in the electrochemical reduction step of Dy₂O₃ were obtained by simulating the AC impedance spectra with equivalent circuits. The electrochemical reduction reaction of Dy₂O₃ is controlled by the charge transfer process at a low voltage range and by the diffusion process at a high voltage range.     

Improved performances of mechanical-activated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>/MWNTs cathode for aqueous rechargeable lithium batteries

LiMn₂O₄/multi-walled carbon nanotubes (MWNTs) composite was synthesized by mechanical activation reaction followed by a heat-treatment (500 °C). The LiMn₂O₄ and LiMn₂O₄/MWNTs as cathodes were investigated in 1 M Li₂SO₄ by cyclic voltammetry (CV), galvanostatic charge/discharge (GC), and electrochemical impedance spectroscopy (EIS). The LiMn₂O₄/MWNTs cathode delivered higher discharge capacity (117 mAh g⁻¹) than LiMn₂O₄ (84.6 mAh g⁻¹). Furthermore, the results from EIS showed that LiMn₂O₄/MWNTs had a faster kinetic process for lithium ion intercalation/de-intercalation than LiMn₂O₄. Besides, LiMn₂O₄/MWNTs had better cycling stability and rate capability than LiMn₂O₄, which was confirmed by GC testing. SEM images showed that a three-dimensional network structure was formed during the mechanical activation, giving a decrease of particle size.     

The role of TiO<Subscript>2</Subscript> layers deposited on YSZ on the electrochemical promotion of C<Subscript>2</Subscript>H<Subscript>4</Subscript> oxidation on Pt

The electrochemical promotion of Pt/YSZ and Pt/TiO₂/YSZ catalyst-electrodes has been investigated for the model reaction of C₂H₄ oxidation in an atmospheric pressure single chamber reactor, under oxygen excess between 280 and 375 °C. It has been found that the presence of a dispersed TiO₂ thin layer between the catalyst electrode and the solid electrolyte (YSZ), results in a significant increase of the magnitude of the electrochemical promotion of catalysis (EPOC) effect. The rate enhancement ratio upon current application and the faradaic efficiency values, were found to be a factor of 2.5 and 4 respectively, higher than those in absence of TiO₂. This significantly enhanced EPOC effect via the addition of TiO₂ suggests that the presence of the porous TiO₂ layer enhances the transport of promoting O²⁻ species onto the Pt catalyst surface. This enhancement may be partly due to morphological factors, such as increased Pt dispersion and three-phase-boundary length in presence of the TiO₂ porous layer, but appears to be mainly caused by the mixed ionic-electronic conductivity of the TiO₂ layer which results to enhanced O²⁻ transport to the Pt surface via a self-driven electrochemical promotion O²⁻ transport mechanism.     

Design of Efficient Ce<Subscript>x</Subscript>M<Subscript>1−x</Subscript>O<Subscript>2−δ</Subscript> (M = Zr,Hf, Tb and Pr) Nanosized Model Solid Solutions for CO Oxidation

Abstract  

Nanosized Ce_xM_1−xO_2−δ (M = Zr, Hf, Tb and Pr) solid solutions were prepared by a modified coprecipitation method and thermally treated at different temperatures from 773 to 1073 K in order to ascertain the thermal behavior. The structural and textural properties of the synthesized samples were investigated by means of X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), BET surface area, X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy (RS) techniques. The catalytic efficiency has been performed towards oxygen storage/release capacity (OSC) and CO oxidation activity. The characterization results indicated that the obtained solid solutions exhibit defective cubic fluorite structure. The solid solutions of ceria–hafnia, ceria–terbia and ceria–praseodymium exhibited good thermal stability up to 1073 K. A new Ce_0.6Zr_0.4O₂ phase along with Ce_0.75Zr_0.25O₂ was observed in the case of ceria–zirconia solid solution due to more Zr⁴⁺ incorporation in the ceria lattice at higher calcination temperatures. The reducibility of ceria has been increased upon doping with Zr⁴⁺, Hf⁴⁺, Tb^3+/4+ and Pr^3+/4+ cations. This enhancement is more in case of Hf⁴⁺ doped ceria. Among various solid solutions investigated, the ceria–hafnia combination exhibited better OSC and CO oxidation activity. The high efficiency of Ce–Hf solid solution was correlated with its superior bulk oxygen mobility and other physicochemical characteristics.     

Thermoelectric Properties of <Emphasis Type="Italic">x</Emphasis>PbTe/Yb<Subscript>0.2</Subscript>Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript> Hot-Pressed Samples

The xPbTe/Yb_0.2Co₄Sb₁₂ compounds were prepared by the ball-milling and hot-pressed process. Electrical conductivity of the composite samples are reduced with a increase in PbTe content; and, their temperature dependence coefficients show the positive values. The maximum electrical conductivity of composite materials is ~80000 Sm⁻¹ at 800 K. The Seebeck coefficient (absolute value) of the composite material is obviously improved with an increase in the dispersed phase (PbTe) content; the Seebeck coefficient (absolute value) of the 10PbTe sample is ~260 μVK⁻¹ at 700 K, which increases by 13.6% relative to that of the Yb_0.2Co₄Sb₁₂ sample. The thermal conductivity of the composite samples is improved due to introduction of PbTe, and the thermal conductivity of the 10PbTe sample is ~3 Wm⁻¹ K⁻¹ at 550 K. The maximum value of ZT is 0.78 at 700 K for the 2.5PbTe sample.