A comparison of ignition characteristics of slurry fuels prepared using coal processing waste and finely divided coal

The scientific novelty of the research is that for the first time differences in the conditions and characteristics of the ignition and burning of droplets of slurries prepared on the basis of coals and waste from their enrichment have been established. The practical significance of the research results is that they illustrate the prospects of utilization of the numerous coal enrichment wastes by combustion in the composition of aqueous slurries with the generation of a rather large amount of energy and a relatively small negative environmental impact. The most significant characteristics were compared: the limiting (minimum) temperature; the ignition delay times; the maximum combustion temperature; the concentration of the main gas anthropogenic emissions. It has been found that fuel mixtures prepared from wet waste of coal flotation are characterized by higher inertia and ignition temperatures compared to slurries with high-quality coal dust. However, the established differences considering the availability and low cost of filter cakes illustrate the prospects of waste derived fuel combustion. The combustion heat of the investigated slurries based on coal and filter cake with addition of petroleum products differs by no more than 5–30%. The average difference between the duration of ignition for fuel droplets based on dust and filter cake of coking and low-caking coals is about 20%. At that the addition of waste turbine oil (10% wt.) into the filter cake reduces the duration of ignition by 12–25% and the ignition temperature – by 10–15 °C without a significant increase in anthropogenic gas emissions. The difference between the minimum ignition temperatures of coal and waste coal based slurries was from 10 °C to 80 °C. On environmental and economic indicators, coal waste is more attractive than coal.     

Effect of ZrO2 on the performance of Co–CeO2 catalysts for hydrogen production from waste-derived synthesis gas using high-temperature water gas shift reaction

In this study, highly active and stable CeO₂, ZrO₂, and Zr_(1-x)Ce_(x)O₂-supported Co catalysts were prepared using the co-precipitation method for the high-temperature water gas shift reaction to produce hydrogen from waste-derived synthesis gas. The physicochemical properties of the catalysts were investigated by carrying out Brunauer-Emmet-Teller, X-ray diffraction, CO-chemisorption, Raman spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and H₂-temperature-programmed reduction measurements. With an increase in the ZrO₂ content, the surface area and reducibility of the catalysts increased, while the interaction between Co and the support and the dispersion of Co deteriorated. The Co–Zr_0.4Ce_0·6O₂ and Co–Zr_0.6Ce_0·4O₂ catalysts showed higher oxygen storage capacity than that of the others because of the distortion of the CeO₂ structure due to the substitution of Ce⁴⁺ by Zr⁴⁺. The Co–Zr_0.6Ce_0·4O₂ catalyst with high reducibility and oxygen storage capacity exhibited the best catalytic performance and stability among all the catalysts investigated in this study.     

Transient performances of the gas turbine recuperating waste heat through hydrogen rich fuels

Operational rules and control strategies of the chemically recuperated gas turbine (CRGT) in the marine propulsion are investigated in this paper. The Minimization of Gibbs free energy method is used to calculate the diesel-steam reforming reaction which products synthetic hydrogen rich fuels, and a universal model of the chemical regenerator which is easily applied to different application environments is created. The hydrogen production and hydrogen molar fraction are investigated to verify that the CRGT improve the combustion performances under low working conditions. Off-design calculations are performed to derive proper operational rules, and transient calculations are performed to investigate the best control strategies for the systems. The modelling approach of the chemical regenerator can be generally used in the chemically recuperated gas turbine. The elaborate operational rules can greatly improve the thermal efficiencies under every working condition. The system using synchronous control strategies have better regulation speed and operation stability than that using asynchronous control strategies.     

Continuous H2 production during fermentation of the carbon components of lignocellulose hydrolysates: Insight into the influence of pH conditions on the conversion efficiency of individual sugars

Sugars released from lignocellulose biomass are a promising substrate for biohydrogen production. This study evaluates the effect of pH controlled between 4.0 and 7.5 on continuous dark-fermentative H₂ production from the mixture of cellobiose, xylose and arabinose. High hydrogen production rate was obtained for pH values between 6.0 and 7.0 with a maximum of 7.41 ± 0.16 L/L-d at pH 7.0. On the other hand, the highest H₂ yields of around 1.74 ± 0.02 mol/mol_consumed were obtained at pH 4.5, 5.0 and 6.0. Cellobiose was completely utilized in nearly the entire pH range, while the highest consumption of xylose and arabinose was obtained at pH 6.0 and 7.0, respectively. It shows the challenges in selecting optimum pH for fermentation of mixed sugars. Significant impact of pH conditions on the microbial structure was observed. Between pH 4.0 and 7.0 Clostridium genus dominated the consortium, while above pH 7.0 relative abundance of Bacillus genus increased significantly.     

DIR-FCEV powered by different fuels – Part I: Well-to-wheel analysis for the Brazilian and Spanish contexts

This article describes the life cycle assessment of the Direct Internal Reforming Fuel Cell Electric Vehicle (DIR-FCEV) for the Brazilian and Spanish contexts. This recently proposed vehicle technology produces hydrogen onboard via heat recovery, while the Solid Oxide Fuel Cell (SOFC) and the gas turbine provide electricity to the electric motor with high overall efficiency. The exhaust gas emission was obtained via GASEQ software and the well-to-tank data were collected through literature search. These values were entered in the GREET Model software version v1.3.0.13656 to assess the negative environmental impacts of the DIR-FCEV in terms of global warming potential (GWP) and human toxicity potential (HTP). Using 1 km distance driven by a light-duty vehicle as the functional unit, the tank-to-wheel results indicate that regardless of the fuel, the DIR-FCEV achieved better than the internal combustion engine vehicle fuelled with gasoline A in both categories. Also, the DIR-FCEV powered by biomethane, gasoline A, gasoline C (73% gasoline A and 27% ethanol, in volume basis), glycerine, and ethanol attended all future tailpipe emissions standards stipulated by United States and European Union. Biomethane and gasoline-fuelled DIR-FCEV had more commendatory environmental performance in both countries. Thus, it is expected to obtain environmental indicators to stimulate the use of biofuels synergistically with the advancement of electromobility in Brazil and Spain.     

Improving inter-plant integration of syngas production technologies by the recycling of CO2 and by-product of the Fischer-Tropsch process

This paper deals with the emission reduction in synthesis-gas production by better integration and increasing the energy efficiency of a high-temperature co-electrolysis unit combined with the Fischer-Tropsch process. The investigated process utilises the by-product of Fischer-Tropsch, as an energy source and carbon dioxide as a feedstock for synthesis gas production. The proposed approach is based on adjusting process streams temperatures with the further synthesis of a new heat exchangers network and optimisation of the utility system. The potential of secondary energy resources was determined using plus/minus principles and simulation of a high-temperature co-electrolysis unit. The proposed technique maximises the economic and environmental benefits of inter-unit integration. Two scenarios were considered for sharing the high-temperature co-electrolysis and the Fischer-Tropsch process. In the first scenario, by-products from the Fischer-Tropsch process were used as fuel for a high-temperature co-electrolysis. Optimisation of secondary energy sources and the synthesis of a new heat exchanger network reduce fuel consumption by 47% and electricity by 11%. An additional environmental benefit is reflected in emission reduction by 25,145 tCO₂/y. The second scenario uses fossil fuel as a primary energy source. The new exchanger network for the high-temperature co-electrolysis was built for different energy sources. The use of natural gas resulted in total annual costs of the heat exchanger network to 1,388,034 USD/y, which is 1%, 14%, 116% less than for coal, fuel oil and LPG, respectively. The use of natural gas as a fuel has the lowest carbon footprint of 7288 tCO₂/y. On the other hand, coal as an energy source has commensurable economic indicators that produce 2 times more CO₂, which can be used as a feedstock for a high-temperature co-electrolysis. This work shows how in-depth preliminary analysis can optimise the use of primary and secondary energy resources during inter-plant integration.     

Hydrofluoroolefin-based mixed refrigerant for enhanced performance of hydrogen liquefaction process

Hydrogen has the highest gravimetric energy density of all fuels; however, it has a low volumetric energy density, unfavorable for storage and transportation. Hydrogen is usually liquefied to meet the bulk transportation needs. The exothermic interconversion of its spin isomers is an additional activity to an already energy-intensive process. The most significant temperature drop occurs in the precooling cycle (between ?150 °C and up to ?180 °C) and consumes more than 50% of the required energy. To reduce the energy consumption and improve the exergy efficiency of the hydrogen liquefaction process, a new high-boiling component, Hydrofluoroolefin (HFO-1234yf), is added to the precooled mixed refrigerant. As a result, the specific energy consumption of precooling cycle reduces by 41.8%, from 10.15 kWh/kg_LH2 to 5.90 kWh/kg_LH2, for the overall process. The exergy efficiency of the proposed case increases by 43.7%; however, the total equipment cost is also the highest. The inflated cost is primarily due to the added ortho-to-para hydrogen conversion reactor, boosting the para-hydrogen concentration. From the perspective of bulk storage and transportation of liquid hydrogen, the simplicity of design and low energy consumption build a convincing case for considering the commercialization of the process.     

Review of hydrogen economy in Malaysia and its way forward

Heavy fossil fuels consumption has raised concerns over the energy security and climate change while hydrogen is regarded as the fuel of future to decarbonize global energy use. Hydrogen is commonly used as feedstocks in chemical industries and has a wide range of energy applications such as vehicle fuel, boiler fuel, and energy storage. However, the development of hydrogen energy in Malaysia is sluggish despite the predefined targets in hydrogen roadmap. This paper aims to study the future directions of hydrogen economy in Malaysia considering a variety of hydrogen applications. The potential approaches for hydrogen production, storage, distribution and application in Malaysia have been reviewed and the challenges of hydrogen economy are discussed. A conceptual framework for the accomplishment of hydrogen economy has been proposed where renewable hydrogen could penetrate Malaysia market in three phases. In the first phase, the market should aim to utilize the hydrogen as feedstock for chemical industries. Once the hydrogen production side is matured in the second phase, hydrogen should be used as fuel in internal combustion engines or burners. In the final phase hydrogen should be used as fuel for automobiles (using fuel cell), fuel-cell combined heat and power (CHP) and as energy storage.     

Molten salt synthesis of high-entropy alloy AlCoCrFeNiV nanoparticles for the catalytic hydrogenation of p-nitrophenol by NaBH4

High-entropy alloy (HEA) AlCoCrFeNiV nanoparticles were prepared from oxide precursors using a molten salt synthesis method without an electrical supply. The oxide precursor was directly reduced by CaH₂ reducing agent in molten LiCl at 600°C-700°C or molten LiCl–CaCl₂ at 500°C-550°C. When the reduction was conducted at 700°C, a face-centered cubic (FCC) structure produced, as identified by X-ray diffraction analysis. With lower reduction temperatures, the FCC structure was absent, replaced by a body-centered cubic (BCC) structure. With a reduction temperature of 550°C, the resulting sample was composed of highly pure HEA AlCoCrFeNiV nanoparticles with a BCC structure of 15 nm. Analyses by scanning electron microscopy/transmission electron microscopy with energy-dispersive X-ray spectroscopy confirmed the formation of homogeneous HEA AlCoCrFeNiV with a nanoscale morphology. In the hydrogenation reaction of p-nitrophenol by NaBH₄, the AlCoCrFeNiV nanoparticles (produced at 550°C) exhibited a catalytic activity with ～90% conversion and 16 kJ/mol activation energy.     

Economic viability assessment of sustainable hydrogen production,storage, and utilisation technologies integrated into on- and off-grid micro-grids: A performance comparison of different meta-heuristics

In recent years, there has been considerable interest in the development of zero-emissions, sustainable energy systems utilising the potential of hydrogen energy technologies. However, the improper long-term economic assessment of costs and consequences of such hydrogen-based renewable energy systems has hindered the transition to the so-called hydrogen economy in many cases. One of the main reasons for this is the inefficiency of the optimization techniques employed to estimate the whole-life costs of such systems. Owing to the highly nonlinear and non-convex nature of the life-cycle cost optimization problems of sustainable energy systems using hydrogen as an energy carrier, meta-heuristic optimization techniques must be utilised to solve them. To this end, using a specifically developed artificial intelligence-based micro-grid capacity planning method, this paper examines the performances of twenty meta-heuristics in solving the optimal design problems of three conceptualised hydrogen-based micro-grids, as test-case systems. Accordingly, the obtained numeric simulation results using MATLAB indicate that some of the newly introduced meta-heuristics can play a key role in facilitating the successful, cost-effective development and implementation of hydrogen supply chain models. Notably, the moth-flame optimization algorithm is found capable of reducing the life-cycle costs of micro-grids by up to 6.5% as compared to the dragonfly algorithm.     

A comprehensive review on the proton conductivity of proton exchange membranes (PEMs) under anhydrous conditions: Proton conductivity upper bound

The present study aims to assess the proton conductivities of the most investigated proton exchange membranes (PEMs) used in PEM fuel cells (PEMFCs). Specifically, PEMs are analyzed for their use in anhydrous fuel cells and proton conductivity upper bounds were provided for them. Considering the direct relationship between proton conductivity and temperature, an upper bound is presented. Based on the obtained upper bounds, suitable membranes for high-temperature performance are determined, and the average range of proton conductivity for each polymer group is discussed. By comparing the available proton conductivity data with upper bound, it was demonstrated that some of poly (ionic liquid)s have provided the highest proton conductivities, however aromatic polymers such as polybenzimidazole (PBI) are found more suitable choices for application at anhydrous conditions and high temperatures. The proton conductivity upper bound for anhydrous PEMs demonstrates the availability of promising polymer options for the deployment of anhydrous fuel cells.     

A comprehensive review on water management strategies and developments in anion exchange membrane fuel cells

In spite of significant achievements in alkaline exchange membrane fuel cells (AEMFCs) in recent years, they are still lagging behind proton exchange membrane fuel cells (PEMFCs) due to performance instability. Among the relevant operational parameters of AEMFC, the researchers have found that poor water management within the cell was the main reason for failure of the system. In the past five years, numerous modeling and experimental works were reported proposing different strategies to improve water management of AEMFC. With proper water management, the achievable power output in AEMFCs is comparable with that of PEMFCs or even more. Efforts have to be continued, but AEMFCs can become a strong competitor in the market place. This review paper discusses the strategies and developments impacting water management of AEMFCs providing knowledge source for upcoming studies.     

CoMo heterohierarchical foam-structured cathode for anion exchange membrane water electrolyzer

It is important to consider the synergy of heterostructures to improve the slow kinetics of water dissociation in the alkaline hydrogen evolution reaction (HER). Herein, we report a simple method to design a heterohierarchical CoMo catalyst. The CoMo catalyst was prepared by simple one-pot electrodeposition on carbon paper (CP). The CoMo/CP catalyst was optimized for the alkaline HER by controlling the electrodeposition bath conditions, potential, and time. The optimized catalyst shows the heterohierarchical structure containing the electrically conductive metallic Co in the bulk and Mo-incorporated Co containing Mo⁴⁺ at the surface. It exhibited a lower HER overpotential of 0.11 V at ?20 mA/cm² compared to those of the others owing to the synergetic effect of the between the Co and Mo incorporated Co. The results highlight the advantages of the simple method developed herein for the design of heterohierarchical catalysts.     

Detonation propagation characteristics of H2/O2/AR in multi-angle bifurcation tubes

The propagation characteristics of the detonation wave in the bifurcated tube with the angular variation range of 30°–90° are simulated with 25% AR as dilution gas for H₂/O₂ mixture fuel at chemical equivalence ratio using the solver DCRFoam built on the OpenFOAM platform. The diffraction and reflection phenomena of detonation waves passing through bifurcation tubes with different angles are studied and analyzed. The results show that the distance from regular reflection to Mach reflection increases with the increase of the bifurcation angle so that after one reflection, the detonation forms three reflection forms with the angle of the different bifurcation tubes. After the first reflection, the detonation waves are more likely to induce the formation of transverse waves in the low-angle bifurcation tube. The lowest collision pressure after the detonation collides with the upper wall to form a secondary reflection occurs in the bifurcation tube between 50° and 60°.     

Biomass gasification coupled with producer gas cleaning,bottling and HTS catalyst treatment for H2-rich gas production

The aim of the present study is to demonstrate the production of hydrogen-rich fuel gas from J. curcas residue cake. A comprehensive experimental study for the production of hydrogen rich fuel gas from J. curcas residue cake via downdraft gasification followed by high temperature water gas shift catalytic treatment has been carried out. The gasification experiments are performed at different equivalence ratios and performance of the process is reported in terms of producer gas composition & its calorific value, gas production rate and cold gas efficiency. The producer gas is cleaned of tar and particulate matters by passing it through venturi scrubber followed by sand bed filter. The clean producer gas is then compressed at 0.6 MPa and bottled into a gas cylinder. The bottled producer gas and a simulated mixture of producer gas are then subjected to high temperature shift (HTS) catalytic treatment for hydrogen enriched gas production. The effect of three different operating parameters GHSV, steam to CO ratio and reactor temperature on the product gas composition and CO conversion is reported. From the experimental study it is found that, the presence of oxygen in the bottled producer gas has affected the catalyst activity. Moreover, higher concentration of oxygen concentration in the bottled producer gas leads to the instantaneous deactivation of the HTS catalyst.     

Thermophysical properties of the liquid organic hydrogen carrier system based on diphenylmethane with the byproducts fluorene or perhydrofluorene

Fluorene (H0-F) and perhydrofluorene (H12-F) represent process-related byproducts formed by a dehydrocyclization step in the liquid organic hydrogen carrier (LOHC) system based on diphenylmethane (H0-DPM) and dicyclohexylmethane (H12-DPM). The influence of these byproducts on the liquid viscosity, surface tension, and liquid density of the DPM-based system was experimentally determined by studying three dehydrogenated binary mixtures with H0-F mole fractions of 0.05, 0.10, and 0.20 as well as one hydrogenated binary mixture with an H12-F mole fraction of 0.10 close to 0.1 MPa from (283–573) K. The densities increase with increasing share of H0-F or H12-F by around 1% per added byproduct mole fraction of 0.1. For the surface tension, an increase relative to the values of H0-DPM or H12-DPM by up to 6% is found. The addition of H0-F to H0-DPM or H12-F to H12-DPM yields a relative increase in viscosity by up to 9% at the lowest temperature studied.     

Expected impacts on greenhouse gas and air pollutant emissions due to a possible transition towards a hydrogen economy in German road transport

Transitioning German road transport partially to hydrogen energy is among the possibilities being discussed to help meet national climate targets. This study investigates impacts of a hypothetical, complete transition from conventionally-fueled to hydrogen-powered German transport through representative scenarios. Our results show that German emissions change between ?179 and +95 MtCO₂eq annually, depending on the scenario, with renewable-powered electrolysis leading to the greatest emissions reduction, while electrolysis using the fossil-intense current electricity mix leads to the greatest increase. German energy emissions of regulated pollutants decrease significantly, indicating the potential for simultaneous air quality improvements. Vehicular hydrogen demand is 1000 PJ annually, requiring 446–525 TWh for electrolysis, hydrogen transport and storage, which could be supplied by future German renewable generation, supporting the potential for CO₂-free hydrogen traffic and increased energy security. Thus hydrogen-powered transport could contribute significantly to climate and air quality goals, warranting further research and political discussion about this possibility.     

Graphite nanopowder functionalized 3-D acrylamide polymeric anode for enhanced performance of microbial fuel cell

3-D highly conductive polyvinyl formaldehyde sponges functionalized with acrylamide are fabricated using polyvinyl alcohol with varying concentrations of graphite nanopowder. The properties of the fabricated anodes are analyzed and its application in microbial fuel cells is evaluated. A comparative study with Graphite felt is also performed to evaluate its commercial viability. The presence of Hydroxyl and Amine functional groups enhanced the hydrophilic and biocompatible nature of the synthesized anodes. The phylogenetic analysis substantiated the biocompatible nature and mercury porosimetry showed macroporous nature of the fabricated anode. The highest power density of ~8 W/m² is recorded for C10 establishing solid biofilm formation. A ~94% COD removal revealed the versatility of the anode for MFC based wastewater treatment. The MFC performance was twice than that of control and was also highest among the most reported modified 3-D anodes. The durability study displayed the commercial opportunity of the anode for real-time MFC operation.     

Economic valuation of green hydrogen charging compared to gray hydrogen charging: The case of South Korea

The South Korean government promotes hydrogen-powered vehicles to reduce greenhouse gas (GHG) emissions but these vehicles use gray hydrogen while charging, which causes GHG emissions. Therefore, converting this fuel into green hydrogen is necessary to help reduce GHG emissions, which will incur investment costs of approximately USD 20 billion over a decade. In this study, a contingent valuation method is applied in an analysis to examine the extent to which consumers are willing to pay for green hydrogen charging compared to gray hydrogen charging. The results indicate that the monthly mean of willingness to pay per driver is 51,674 KRW (USD 45.85), equivalent to 4302 KRW per kg (USD 3.82). Additionally, consumers accept a 28.5% increase in the monthly average fuel expenses when converting to green hydrogen. These findings can be used in the development of pricing and energy use plans to finance the expansion of green hydrogen infrastructure.