Ferroelectric and dielectric properties of sol-gel derived BaxSr1−xTiO3 thin films

Ferroelectric thin films of Ba_0.7Sr_0.3TiO₃, Ba_0.8Sr_0.2TiO₃, Ba_0.9Sr_0.1TiO₃ and BaTiO₃ were fabricated by a modified sol-gel technique on Pt/Ti/SiO₂/Si substrates. All the compositions crystallized in perovskite structure and consist of well-defined grains. As the value of x increases grain size of the Ba_xSr_1−xTiO₃ thin films increases while the dielectric permittivity decreases. Ba_0.7Sr_0.3TiO₃ composition possesses the highest dielectric permittivity of 748 (at 100 kHz). Hysteresis loops measured at room temperature for all compositions showed that BaTiO₃ has the largest remnant polarization of 4.8 μC/cm². The dielectric and ferroelectric properties of the sol-gel derived Ba_xSr_1−xTiO₃ thin films are strongly dependent on the Sr content and the grain size.     

High dielectric tunability of Ba0.6Sr0.4TiO3 thin film deposited by radio-frequency magnetron sputtering

In microwave tunable devices, one of the major challenges encountered is the simultaneous minimization of the material's dielectric loss and maximization of dielectric tunability. In this work, Ba_0.6Sr_0.4TiO₃ thin film with the thickness of 300 nm was deposited on Pt/SiO₂/Si substrates using radio-frequency magnetron sputtering technique, and its dielectric properties were investigated. Due to the high temperature annealing process at substrate temperature of 600 °C, well-crystallized Ba_0.6Sr_0.4TiO₃ film was deposited. The dielectric constant and dielectric loss of the film at 100 kHz are 300 and 0.033, respectively. Due to the good crystallinity of the Ba_0.6Sr_0.4TiO₃ films deposited by radio-frequency magnetron sputtering, high dielectric tunability up to 38.3% is achieved at a low voltage of 4.5 V.     

Preparation and characterization of Ba1 − xSrxTiO3 thin films deposited on Pt/SiO2/Si by sol-gel method

BST thin films have been investigated as potential candidates for use in frequency agile microwave circuit devices. Stoichiometric (Ba_1 − xSr_x)TiO₃ (BST) thin films have been prepared on Pt/SiO₂/Si substrates using sol-gel method. The BST films were characterized by X-ray fluorescence (XRF) spectroscopy analysis, X-ray diffraction (XRD), scanning electron microscope (SEM) and electrical measurements. The relationships of processing parameters, microstructures, and dielectric properties are discussed. The results show that the films exhibit pure perovskite phase through rapid thermal anneal at 700 °C and their grain sizes are about 20-40 nm. The dielectric constants of BST5, BST10, BST15 and BST20 are 323, 355, 382 and 405, respectively, at 80 kHz.     

Dielectric and tunable properties of Pb0.25BaxSr0.75−xTiO3 thin films fabricated by a modified sol-gel method

A modified sol-gel method was used to fabricate (Pb_0.25Ba_x Sr_0.75−x)TiO₃ (PBST) thin films with x = 0.05,0.1,0.15 and 0.2 on Pt/TiO₂/SiO₂/Si substrate. The structure, surface morphology, dielectric and tunable properties of PBST thin films were investigated as a function of barium content (x). X-ray diffraction and scanning electron microscopy analysis showed that we could get pure PBST perovskite phase and relative fine density thin films with smooth surface. It was found that the crystal lattice constant, grain size, room temperature dielectric constant, dielectric loss and tunability of Ba solutionizing PST thin films increased with the increase in Ba content. For (Pb_0.25Ba_0.2Sr_0.55)TiO₃ thin film, it had the highest dielectric constant of 1390 and the largest tunability of 80.6%. The figure of merit parameter reached a maximal value of 28.9 corresponding to the (Pb_0.25Ba_0.05 Sr_0.7)TiO₃ thin film, whose dielectric constant, dielectric loss and tunability measured at 1 MHz were 627, 0.024 and 69.4%, respectively.     

Composition dependent preferential orientation, dielectric and ferroelectric properties of Pb(ZrxTi1 − x)O3 thin films derived by sol-gel process

Pb(Zr_xTi_1 − x)O₃ (x = 0.35, 0.40, 0.60, 0.65) thin films were prepared by sol-gel spin on technique. From the X-ray diffraction analysis, PZT films with Zr-rich compositions (x = 0.60 and 0.65) had (111) preferential orientation and the preferential orientation changed to (100) for Ti-rich compositions (x = 0.35 and 0.40). The dielectric measurements on the above compositions at room temperature showed that the dielectric constant values were higher in Zr-rich compositions compared to Ti-rich compositions. The ferroelectric behavior measured in terms of the remnant polarization (P_r) and coercive field (E_c) up to an applied field of 260 kV/cm depicted that the Zr-rich PZT films with (111) preferential orientation had higher P_r and lower E_c values compared to the Ti-rich PZT films with (100) preferential orientation can be understood from the domain switching mechanism.     

Microstructure and electrical properties of Ba0.7Sr0.3(Ti1 − xZrx)O3 thin films prepared on copper foils with sol-gel method

Ba_0.7Sr_0.3(Ti_1 − xZr_x)O₃ (x = 0, 0.1, 0.2) (BSZT) thin films have been prepared on copper foils using sol-gel method. The films were annealed in an atmosphere with low oxygen pressure so that the substrate oxidation was avoided and the formation of the perovskite phase was allowed. The X-ray diffraction results show a stable polycrystalline perovskite phase, with the diffraction peaks of the BSZT films shifting toward the smaller 2θ with increasing Zr content. Scanning electron microscopy images show that the grain size of the BSZT thin films decreases with increasing Zr content. High resolution transmission electron microscopy shows the clear lattice and domain structure in the film. The dielectric peaks of the BSZT thin films broaden with increasing Zr content. Leakage current density of Ba_0.7Sr_0.3(Ti_1 − xZr_x)O₃ (x = 0.1) thin film is the lowest over the whole applied voltage.     

Bottom electrodes dependence of microstructures and dielectric properties of compositionally graded (Ba1−xSrx)TiO3 thin films

Compositionally graded (Ba_1−xSr_x)TiO₃ (BST) thin films, with x decreasing from 0.3 to 0, were deposited on Pt/Ti/SiO₂/Si and Ru/SiO₂/Si substrates by radio frequency magnetron sputtering technology. The microstructure and dielectric properties of the graded BST thin films were investigated. It was found that the films on Ru electrode have better crystallization, and that RuO₂ is present between the Ru bottom electrode and the graded BST thin films by X-ray diffraction and SEM analysis. Dielectric measurement reveals that the graded BST thin films deposited on Ru bottom electrode have higher dielectric constant and tunability. The enhanced dielectric behavior is attributed to better crystallization as well as smaller space charge capacitance width and the formation of RuO₂ that is more compatible with the BST films. The graded BST films on Ru electrode show higher leakage current due to lower barrier height and rougher surface of bottom electrode.     

Dielectric and ferroelectric properties of Ba(Sn0.15Ti0.85)O3 thin films grown by a sol-gel process

Ferroelectric Ba(Sn_0.15Ti_0.85)O₃ (BTS) thin films were deposited on LaNiO₃-coated silicon substrates via a sol-gel process. Films showed a strong (1 0 0) preferred orientation depending upon annealing temperature and concentration of the precursor solution. The dependence of dielectric and ferroelectric properties on film orientation has been studied. The leakage current density of thin films at 100 kV/cm was 7 × 10⁻⁷ A/cm² and 5 × 10⁻⁵ A/cm² and their capacitor tunability was 54 and 25% at an applied field of 200 kV/cm (measurement frequency of 1 MHz) for the thin films deposited with 0.1 and 0.4 M spin-on solution, respectively. This work clearly reveals the highly promising potential of BTS compared with BST films for application in tunable microwave devices.     

Enhanced ferroelectric properties of Pb(Zr0.80Ti0.20)O3/PbO thin films prepared by radio frequency magnetron sputtering

The Pb(Zr_0.80Ti_0.20)O₃ (PZT) thin films with and without a PbO buffer layer were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by radio frequency (rf) magnetron sputtering method. The PbO buffer layer improves the microstructure and electrical properties of the PZT thin films. High phase purity and good microstructure of the PZT thin films with a PbO buffer layer were obtained. The effect of the PbO buffer layer on the ferroelectric properties of the PZT thin films was also investigated. The PZT thin films with a PbO buffer layer possess better ferroelectric properties with higher remnant polarization (P_r = 25.6 μC/cm²), and lower coercive field (E_c = 60.5 kV/cm) than that of the films without a PbO buffer layer (P_r = 9.4 μC/cm², E_c = 101.3 kV/cm). Enhanced ferroelectric properties of the PZT thin films with a PbO buffer layer is attributed to high phase purity and good microstructure.     

Reactively sputtered GaAsxN1−x thin films

Thin films of GaAs_xN_1−x alloys were deposited by reactive rf magnetron sputtering of GaAs target with a mixture of argon and nitrogen as the sputtering gas. Growth rate was found to decrease from ∼ 7 μm/h to ∼ 2 μm/h as the nitrogen content increased from 0% to 40%. XRD and TEM studies of the films reveal the presence of hexagonal GaN with a significant increase of the lattice parameters in a narrow range of composition of the sputtering gas (5-10% nitrogen), which is attributed to the incorporation of arsenic. The limited availability of nitrogen in the sputtering atmosphere is found to encourage the incorporation of arsenic in the alloy films. Optical absorption coefficient spectra of the films were obtained from reflection and transmission data. The effect of arsenic incorporation is seen in the optical absorption spectra of the films, which show a continuous shift of the absorption edge to lower energies with respect to that of gallium nitride.     

Different microstructure and dielectric properties of Ba1−xCaxTiO3 ceramics and pulsed-laser-ablated films

A comparative study of the microstructure and dielectric properties between Ba_1−xCa_xTiO₃ (BCT) ceramics and films were performed in the whole Ca concentration range of x = 0-1. The ceramics were prepared by conventional solid-state reaction technique and the films by the method of pulsed-laser deposition. X-ray diffraction (XRD) study of the BCT ceramics exhibited a pure tetragonal phase for x = 0-0.25, a tetragonal-orthorhombic diphase for x = 0.25-0.85 and a pure orthorhombic phase for x = 0.90-1.00. And the dielectric phase transition temperature from tetragonal to cubic was marginally affected by the Ca doping into BaTiO₃. However, BCT films deposited on Pt/Si/SiO₂/Si substrates showed a different microstructure and dielectric properties. Tetragonal-orthorhombic diphase was not found in the BCT films for x = 0.25-0.85, and a large decrease of the Curie point and diffuse phase transition were observed in the BCT films. Based on the compositional analysis, such phenomena were ascribed to the occupancy of some Ca²⁺ to the Ti⁴⁺ sites in the BCT films.     

Pechini sol-gel deposition and luminescent properties of SrLa1−xRExGa3O7 (RE = Eu, Tb) phosphor films

SrLa_1−xRE_xGa₃O₇ (RE = Eu³⁺, Tb³⁺) phosphor films were deposited on quartz glass substrates by a simple Pechini sol-gel method. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), atomic force microscopy, field-emission scanning electron microscopy, photoluminescence spectra, and lifetimes were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 700 °C and crystallized fully at 900 °C. The results of FT-IR spectra were in agreement with those of XRD. Uniform and crack-free films annealed at 900 °C were obtained with average grain size of 80 nm, root mean square roughness of 46 nm and thickness of 130 nm. The RE ions showed their characteristic emission in crystalline SrLa_1−xRE_xGa₃O₇ films, i.e., Eu³⁺⁵D₀-⁷F_J (J = 0, 1, 2, 3, 4), Tb³⁺⁵D₄-⁷F_J (J = 6, 5, 4, 3) emissions, respectively. The optimum concentrations (x) of Eu³⁺ and Tb³⁺ were determined to be 50, and 80 mol% in SrLa_1−xRE_xGa₃O₇ films, respectively.     

Enhanced photocatalytic activity of silver nanoparticles modified TiO2 thin films prepared by RF magnetron sputtering

Ag-TiO₂ nanostructured thin films with silver volume fraction of 0–40% were prepared by RF magnetron sputtering. The microstructure, surface topography, and optical properties of the films were characterized by X-ray diffractometer, transmission electron microscope, and ultraviolet–visible spectrophotometer. Photocatalytic activity of the films was evaluated by light-induced degradation of methyl orange (C₁₄H₁₄N₃NaO₃S) solution using a high pressure mercury lamp as lamp-house. The relation of photocatalytic activity and silver content was studied in detail. It is found that silver content influences microstructure of TiO₂ thin films, and silver in the films is metallic Ag (Ag⁰). Photocatalytic activity of the films increases with increasing silver content up to 5 vol.% Ag and then decreases to values significantly still bigger than that of pure TiO₂ thin films. Silver nanoparticles significantly enhance the photocatalytic activity of TiO₂ films. The better separation between electrons and holes on silver modified TiO₂ thin films surface allowed more efficiency for the oxidation and reduction reactions. The enhanced photocatalytic activity was mainly attributed to the decrease of energy gap of the films and the increase of oxygen anion radicals O₂⁻ and reactive center of surface Ti³⁺ on silver modified TiO₂ thin films surface.     

Compositional effects on the optical properties of Gex Sb40−x Se60 thin films

Ge_x Sb_40−x Se₆₀ (x = 0, 2.42 and 23.41 at.%) thin chalcogenide films were deposited on glass and quartz substrates by the conventional thermal evaporation technique at 300 K. The chemical composition of the bulk material and as-deposited films were determined by energy dispersive analysis X-ray spectrometry (EDAX). X-ray diffraction pattern (XRD) of Ge_x Sb_40−x Se₆₀ (x = 0, 2.42 and 23.41 at.%) thin films indicates that they have amorphous structure. The optical transmission and reflection spectra were measured in the range of 500 to 2500 nm. The optical absorption coefficient spectra were studied for deposited samples. It is observed that the optical absorption edge shift to higher energy range, as the germanium content, x, increases in the film. The type of electronic transition, responsible for the optical properties, is indirect allowed transition. It is found that the optical band gap increases as the Ge content increases.The average coordination number (N_c) in Ge_x Sb_40−x Se₆₀ films increases, but the number of chalcogenide atoms remains constant. The number of Ge - Se bonds and the average bond energy of the system increase with the increase of the average coordination number. The optical band gap, E_g, increases with the increase of the average coordination number, (N_c). Also the energy gap, E₀₄, is discussed in terms of its relation to the chemical composition. The dispersion of the refractive index (n) is discussed in terms of the Single Oscillator Model (SOM) (Wimple - Didomenico model). The single oscillator energy (E₀), the dispersion energy (E_d) and the optical dielectric constant (?_∞) are also estimated.     

Microfabrication of dilute magnetic semiconducting Ti1−xCoxO2 films using photosensitive sol-gel method

Photosensitive Ti_1−xCo_xO₂ gel films are prepared by chemical modification with benzoylacetone, and then their Fourier transform infrared spectra and ultraviolet visible spectra are measured. Results show that the chelate rings of benzoylacetone with Ti ions are formed in the Ti_1−xCo_xO₂ gel films. With irradiation of UV light, the chelate rings are photolyzed, which leads to a change of the solubility of the Ti_1−xCo_xO₂ gel films in methanol. Based on this, the micro-patterns of Ti_1−xCo_xO₂ gel films are obtained. After the patterned gel films are dried at 200 °C and are fired at 550 °C for 1 h, negative patterned Ti_1−xCo_xO₂ inorganic films are obtained. The Ti_1−xCo_xO₂ films have an anantase structure and exhibit a room temperature ferromagnetic property.     

Effect of Bi and Ti substitutions for Na and Nb on ferroelectric properties of oriented (Bi4.5+xNa0.5−x)(Ti2xNb2−2x)WO15 compounds

(Bi_4.5+xNa_0.5−x)(Ti_2xNb_2−2x)WO₁₅ (BNTNW) compounds were synthesized and their ferroelectric properties were characterized. The X-ray powder diffraction patterns of the compounds revealed that they have a single phase over the whole composition range. The linear variations of the lattice parameters with composition indicate the formation of solid solutions, resulting in a reduction in the orthorhombicity of the compounds. The remnant polarization of the BNTNW decreased from 8.5 to 5.1 μC/cm² with increasing x, which may be related to the orthorhombicity of the compounds. By using hot forging, an oriented BNTNW compound at x = 0 was obtained. Strong reflections from (0 0 l) were observed for sample // in which the measurement direction is parallel and the orientation factor of such sample was approximately 0.72. A remarkable increase in the remnant polarization (P_r) of the compound was observed for the sample ⊥ in which the direction of applied pressure is perpendicular to the measurement direction; the highest P_r value was 18 μC/cm².     

Optical properties of Cd1−xZnxS thin films for CuInGaSe2 solar cell application

The photovoltaic Cd_1−xZn_xS thin films, fabricated by chemical bath deposition, were successfully used as n-type buffer layer in CuInGaSe₂ (CIGS) solar cells. Comprehensive optical properties of the Cd_1−xZn_xS thin films were measured and modeled by spectroscopic ellipsometry (SE), which is proven to be an excellent and non-destructive technique to determine optical properties of thin films. The optical band gap of Cd_1−xZn_xS thin films can be tuned from 2.43 eV to 3.25 eV by controlling the Zn content (x) and deposition conditions. The wider-band-gap Cd_1−xZn_xS film was found to be favorable to improve the quantum efficiency in the wavelength range of 450-550 nm, resulting in an increase of short-circuits current for solar cells. From the characterization of quantum efficiency (QE) and current-voltage curve (J-V) of CIGS cells, the Cd_1−xZn_xS films (x = 0.32, 0.45) were demonstrated to significantly enhance the photovoltaic performance of CIGS solar cell. The highest efficiency (10.5%) of CIGS solar cell was obtained using a dense and homogenous Cd_0.68Zn_0.32S thin film as the buffer layer.     

Preparation and magnetic properties of SrFeO3−x (x = 0.25 ∼ 0.5) using RF magnetron sputtering optimized through sputtering plasma analysis

We investigated the preparation and the magnetic properties of SrFeO_3−x using conventional RF magnetron sputtering. Photoluminescence spectrum analyses of the sputtering plasma revealed that the film composition was changed even using the stoichiometry target. After fixing the composition of the targets from an intensity ratio of the Sr and Fe plasma, the polycrystalline SrFeO_3−x films with different oxygen deficiencies were able to prepare using the various sputtering gas ratio. The magnetic properties of the samples were also changed with changing the sputtering gas ratio. This magnetic property change was likely due to the suppression of the oxygen deficiency in the film.     

Structure and properties of ternary manganese nitride Mn3CuNy thin films fabricated by facing target magnetron sputtering

Deposition of Mn₃CuN_y thin films on single crystal Si (1 0 0) at various substrate temperatures (T_sub) by facing target magnetron sputtering is reported. The crystal structure and composition were characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The results confirmed that the crystalline antiperovskite Mn₃CuN_y thin film with (2 0 0) highly preferred texture had been obtained at T_sub = 180 °C. Furthermore, for the resulting Mn₃CuN_y thin film, it showed different properties compared with the bulk counterpart. There was a paramagnetic to ferrimagnetic transition at 225 K with decreasing temperature. The change of the lattice constant with temperature presented positive thermal expansion behavior and no structural transition was observed. The average linear thermal expansion coefficient (α) is 2.49 × 10⁻⁵ K⁻¹ from 123 K to 298 K. More interestingly, the temperature dependence of resistivity displayed a semiconductor-like behavior, i.e. an obvious monotonous decrease of resistivity with increasing temperature.     

Polarization fatigue and photoinduced current in (Pb0.72La0.28)Ti0.93O3 buffered Pb(Zr0.52Ti0.48)O3 films on platinized silicon

We report a study on the fatigue behavior of Pb(Zr_0.52Ti_0.48)TiO₃ (PZT) films deposited on Pt/Ti/SiO₂/Si substrates by a sol-gel method with single- and double-sided (Pb_0.72La_0.28)Ti_0.93O₃ (PLT) buffer layers, with an attempt to clarify the role of the top and bottom PLT buffer layers on the fatigue endurance (FE) of the PZT films. It is revealed that the existence of the PLT buffer layer and the level of driving alternating-current electric switching field strongly influence the fatigue properties. In terms of the existence of an asymmetric built-in electric field near the top and bottom interfaces between the film and metal electrode, we explain the observed fatigue properties.