纳米晶WC-10Co复合粉末的烧结致密化行为

研究了机械合金化纳米晶WC-10Co复合粉末的真空烧结致密化行为和一般规律.结果表明:烧结温度的提高和烧结时间的延长有利于样品的烧结致密化过程,在1 275～1 300℃致密化速度快,在1 300℃,15 min左右致密化过程已基本完成;VC、Cr3C2等复合晶粒长大抑制剂含量的增加不利于致密化过程;新型晶粒长大抑制剂A可以更有效地阻碍晶粒长大;纳米晶WC-10Co-0.8VC/Cr3C2-0.2A复合粉末压坯在1375℃,30min烧结条件下,所得的密度为14.48 g/cm3,晶粒尺寸约为180 nm.     

溶胶-喷雾干燥超细/纳米晶W-20Cu复合粉末的烧结行为

采用喷雾干燥-氢气还原法制备超细/纳米晶W-20Cu(质量分数,%)复合粉末,粉末压坯直接从室温推入高温区烧结不同时间后直接取出水淬,研究其烧结致密化和显微组织的变化。结果表明,超细/纳米晶W-20Cu粉末在1000～1200℃烧结时发生迅速致密化。粉末压坯在1200℃烧结60min,其材料致密度已达到96.4%。1420℃烧结90min时致密度达到99%以上。1100～1420℃烧结时其烧结致密化活化能不断减小,从1100℃时的276.3kJ/mol减小到1420℃时的29.1kJ/mol。当温度低于1200℃时,W晶粒长大不明显,当温度超过1300℃时,W晶粒开始有明显长大。随温度的升高W晶粒发生显著球形化,1420℃烧结时发现其晶粒长大符合G3=kt的Ostwald机制,此时晶粒长大动力学系数K仅为0.024μm3/min。     

W-30Cu纳米复合粉末液相烧结致密化与晶粒长大机制

采用喷雾干燥-煅烧、还原工艺制备超细W-30Cu复合粉末,将粉末模压成形,在1340～1420℃液相烧结15～120min,研究其致密化行为及晶粒长大机制。结果表明:W-30Cu复合粉末在液相烧结早期发生了显著的致密化,1340℃烧结15 min致密度可达到90%以上;随烧结时间的延长致密度增加,1380℃烧结90 min相对密度达到99.1%。液相烧结过程中,W晶粒不断长大并逐渐球化,且其晶粒大小G与烧结时间t符合G3∝kt关系,服从液相烧结溶解-析出机制。烧结温度对W晶粒长大影响显著,当温度从1340℃上升到1420℃时,其晶粒长大动力学系数从1.61×10-2μm3/min增大到4.65×10-2μm3/min,液相的形成、颗粒重排、溶解-析出及W晶粒长大使细晶W-Cu获得近全致密。     

超细/纳米W-20Cu复合粉末的液相烧结机制

采用溶胶-喷雾干燥及氢还原工艺制备超细/纳米W-20 Cu复合粉末:将粉末压制成形,在1 340～1 420℃烧结5～180 min,并研究其致密化行为及晶粒长大机制.结果表明:烧结温度对液相烧结致密化起主要作用,W-20Cu复合粉末在液相烧结早期发生了显著的致密化,在1 420℃烧结5 min时,致密度可达到89％以上;随烧结时间的延长,致密度增加,在1 420℃烧结90 min时,相对密度最高,达到99.1％.液相烧结时,W晶粒不断长大并逐渐球化,且其晶粒大小G与时间烧结t符合G3＝G30+kt关系,服从溶解-析出机制.烧结温度对W晶粒长大影响显著,当温度从1 340℃上升到1 420℃时,其晶粒长大动力学系数从1.59×10-2 μm3/min增大到2.47×10-2 μm3/min,这说明液相的形成、颗粒重排、溶解-析出及W晶粒长大使得细晶W-Cu坯体获得近全致密.     

纳米晶Mo-Cu复合粉末烧结行为的研究

采用溶胶-喷雾干燥-煅烧-氢气还原的方法制备了纳米晶Mo-18Cu、Mo-30Cu、Mo-40Cu复合粉末,研究了纳米晶Mo-Cu粉末的烧结行为以及Cu含量对致密化的影响.结果表明,纳米晶Mo-Cu复合粉末致密化程度高,速度快,在1050～1200 ℃烧结,Mo-30Cu和Mo-40Cu的相对密度可达98%以上,且合金晶粒细小,而Mo-18Cu在1350 ℃以上烧结,相对密度也可达98%以上,但晶粒聚集长大到5 μm左右.研究发现Mo-Cu复合粉末形成了亚稳态的超饱和Mo(Cu)固溶体,随着烧结温度的升高,Cu相逐渐从亚稳态的超饱和Mo(Cu)固溶体颗粒中析出.     

90W-7Ni-3Fe纳米晶粉末的瞬时液相强化烧结特征

采用机械合金化(MA)制备了晶粒尺寸为8～18 nm的90W-7Ni-3Fe纳米晶粉末(MA粉末).将粉末注射成形,在1 480～1 500℃经3～5 min瞬时液相烧结.结果表明,采用瞬时液相强化烧结可以得到W晶粒为3～8 μm近全致密的细晶钨合金,显微组织为细小的球形W晶粒均匀地连续分布在纤维状粘结相中,烧结坯具有好的拉抻性能.长时间的传统液相烧结使球状W晶粒迅速粗化,而且密度和强度下降,但延伸率反而增加.在MA粉末中添加微量Y2O3后采用瞬时液相烧结,可以使合金抗拉强度提高到1 055 MPa,延伸率提高到16.5%.     

Fe86Zr5Nb6B3非晶合金超高压烧结

借助XRD，DSC，TEM等分析手段，研究了Fe86Zr5Nb6B3快淬带球磨粉末的热稳定性以及高压烧结条件对块体合金的相组成和晶粒尺寸的影响。结果表明：（1）球磨快淬粉末仍为非晶态，其晶化温度约510℃，该晶化过程的表观激活能庐219．5kJ／mol：（2）在5．5GPa，3min烧结条件下，当Pw=1150W后，获得了相对密度为99．1％，单相α-Fe纳米晶（20．6rim）块体合金：（3）在5．5GPa，1150W烧结条件下，当t延长至25min后，α-Fe相纳米晶粒尺寸长大到28.7nm；（4）在5．5GPa，1150W，5min烧结条件下，纳米晶块体合金的饱和磁感应强度Bs=1．26T，矫顽力Hc=4．27kA．m^-1。     

放电等离子烧结制备超细晶粒W-TiC复合材料

采用机械合金化和放电等离子烧结(SPS)技术制备了纳米TiC颗粒弥散增强超细晶W-TiC复合材料,对超细晶W-TiC复合材料的显微组织和室温力学性能进行了研究。研究表明,采用SPS工艺于1700℃下烧结1min可获得烧结颗粒结合良好,致密度高达约98.6%的超细晶W-TiC复合材料。通过添加纳米TiC,不仅能抑制W晶粒的长大,还能促进W的致密化。当TiC的加入量为0.7%时(质量分数,下同)可获得晶粒尺寸为0.5μm,抗弯强度和维氏硬度分别为1262MPa,6.45GPa的超细晶W-TiC复合材料。     

CoSb3纳米晶块体热电材料的制备研究

采用机械合金化．放电等离子烧结工艺(MA-SPS)，在200℃～600℃之间制备了纳米晶CoSb3合金块体材料。采用XRD和TEM对材料的相组成和微观组织进行了测试分析。实验结果表明，烧结前粉末为高能球磨得到的平均晶粒尺寸为20nm～35nm的纳米晶CoSb3粉末，SPS烧结后CoSb3合金块体的平均晶粒尺寸小于100nm，其致密度达到了91．3％～99．6％。CoSb3块体的晶粒尺寸随着烧结温度的降低而减小，而密度却随着烧结温度的升高而增加。CoSb3纳米晶块体热电材料的制备机理是MA使粉末晶粒细化到纳米级，放电等离子烧结的快速、短时、低温和特殊烧结机理显著抑制了烧结时的晶粒长大。     

纳米强化片状W/Co/C复合粉末的制备与烧结体性能

采用高效球磨细氧化钨、扁平片状W粉、碳黑、钴及适量晶粒长大抑制剂等为原料,通过碳辅助氢还原制备质量分数20％纳米钨强化片状W/Co/C复合粉末,于低压真空烧结炉中在1 410℃的温度下一次碳化烧结,制备了含片状晶WC-10％Co(质量分数)硬质合金,研究了质量分数20％纳米W的引入对合金烧结致密化及其性能的影响.对不同...     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。