A 1.2 mW RDS receiver for portable applications

A 0.9 V 1.2 mA fully integrated radio data system (RDS) receiver for the 88-108 MHz FM broadcasting band is presented. Requiring only a few external components (matching network, VCO inductors, loop filter components), the receiver, which has been integrated in a standard digital 0.18 /spl mu/m CMOS technology, achieves a noise figure of 5 dB and a sensitivity of -86dBm. The circuit can be configured and the RDS data retrieved via an I/sup 2/C interface so that it can very simply be used as a peripheral in any portable application. A 250 kHz low-IF architecture has been devised to minimize the power dissipation of the baseband filters and FM demodulator. The frequency synthesizer consumes 250 /spl mu/A, the RF front-end 450 /spl mu/A while providing 40 dB of gain, the baseband filter and limiters 100 /spl mu/A, and the FM and BPSK analog demodulators 300 /spl mu/A. The chip area is 3.6 mm/sup 2/.     

A 72-mW CMOS 802.11a direct conversion front-end with 3.5-dB NF and 200-kHz 1/f noise corner

A direct conversion 802.11a receiver front-end including a synthesizer with quadrature VCO has been integrated in a 0.13-/spl mu/m CMOS process. The chip has an active area of 1.8 mm/sup 2/ with the entire RF portion operated from 1.2 V and the low frequency portion operated from 2.5 V. Its key features are a current driven passive mixer with a low impedance load that achieves a low 1/f noise corner and an high I-Q accuracy quadrature VCO. Measured noise figure is 3.5 dB with an 1/f noise corner of 200 kHz, and an IIP3 of -2 dBm. The synthesizer DSB phase noise integrated over a 10 MHz band is less than -36 dBc while its I-Q phase unbalance is below 1 degree.     

Low-power fully integrated and tunable CMOS RF wireless receiver for ISM band consumer applications

A 0.25-/spl mu/m single-chip CMOS single-conversion tunable low intermediate frequency (IF) receiver operated in the 902-928-MHz industrial, scientific, and medical band is proposed. A new 10.7-MHz IF section that contains a limiting amplifier and a frequency modulated/frequency-shift-key demodulator is designed. The frequency to voltage conversion gain of the demodulator is 15 mV/kHz and the dynamic range of the limiting amplifier is around 80 dB. The sensitivity of the IF section including the demodulator and limiting amplifier is -72 dBm. With on-chip tunable components in the low-power low-noise amplifier (LNA) and LC-tank voltage-controlled oscillator circuit, the receiver measures an RF gain of 15 dB at 915 MHz, a sensitivity of -80 dBm at 0.1% bit-error rate, an input referred third-order intercept point of -9 dBm, and a noise figure of 5 dB with a current consumption of 33 mA and a 2450 /spl mu/m/spl times/ 2450 /spl mu/m chip area.     

A single-chip digitally calibrated 5.15-5.825-GHz 0.18-/spl mu/m CMOS transceiver for 802.11a wireless LAN

The drive for cost reduction has led to the use of CMOS technology in the implementation of highly integrated radios. This paper presents a single-chip 5-GHz fully integrated direct conversion transceiver for IEEE 802.11a WLAN systems, manufactured in 0.18-/spl mu/m CMOS. The IC features an innovative system architecture which takes advantage of the computing resources of the digital companion chip in order to eliminate I/Q mismatch and achieve accurately matched baseband filters. The integrated voltage-controlled oscillator and synthesizer achieve an integrated phase noise of less than 0.8/spl deg/ rms. The receiver has an overall noise figure of 5.2 dB and achieves sensitivity of -75 dBm at 54-Mb/s operation, both referred to the IC input. The transmit error vector magnitude is -33 dB at -5-dBm output power from the integrated power-amplifier driver amplifier. The transceiver occupies an area of 18.5 mm/sup 2/.     

An integrated low power highly linear 2.4-GHz CMOS receiver front-end based on current amplification and mixing

A low power 2.4-GHz complementary metal oxide semiconductor (CMOS) receiver front-end using highly linear mixer based on current amplification and mixing is reported. In the proposed mixer, linearity is greatly improved by using current mirror amplifier and transconductance linearization using multiple gated transistors. Single IF direct conversion receiver (DCR) architecture is used to achieve higher level of integration and to relax the problem of DCR. The fully integrated receiver front end is fabricated in 0.18-/spl mu/m CMOS technology and HP3 of -9 dBm with a gain of 32 dB and noise figure of 6.5 dB are obtained at 8.8 mW power consumption.     

A single-chip dual-band direct-conversion IEEE 802.11a/b/g WLAN transceiver in 0.18-/spl mu/m CMOS

This paper presents a single-chip dual-band CMOS direct-conversion transceiver fully compliant with the IEEE 802.11a/b/g standards. Operating in the frequency ranges of 2.412-2.484 GHz and 4.92-5.805 GHz (including the Japanese band), the fractional-N PLL based frequency synthesizer achieves an integrated (10 kHz-10 MHz) phase noise of 0.54/spl deg//1.1/spl deg/ for 2/5-GHz band. The transmitter error vector magnitude (EVM) is -36/-33 dB with an output power level higher than -3/-5dBm and the receiver sensitivity is -75/-74 dBm for 2/5-GHz band for 64QAM at 54 Mb/s.     

A CMOS passive mixer with low flicker noise for low-power direct-conversion receiver

A CMOS passive mixer is designed to mitigate the critical flicker noise problem that is frequently encountered in constituting direct-conversion receivers. With a unique single-balanced passive mixer design, the resulted direct-conversion receiver achieves an ultralow flicker-noise corner of 45 kHz, with 6 dB more gain and much lower power and area consumption than the double-balanced counterpart. CMOS switches with a unique bias-shifting network to track the LO DC offset are devised to reduce the second-order intermodulation. Consequently, the mixer's IIP2 has been greatly enhanced by almost 21 dB from a traditional single-balanced passive mixer. An insertion compensation method is also implemented for effective dc offset cancellation. Fabricated in 0.18 /spl mu/m CMOS and measured at 5 GHz, this passive mixer obtains 3 dB conversion gain, 39 dBm IIP2, and 5 dBm IIP3 with LO driving at 0 dBm. When the proposed mixer is integrated in a direct-conversion receiver, the receiver achieves 29 dB overall gain and 5.3 dB noise figure.     

A CMOS RF front-end for a multistandard WLAN receiver

This letter describes the design and performance of a dual band tri-mode receiver front-end compliant with the IEEE 802.11a, b, and g standards. The receiver front-end was built in a 0.18-/spl mu/m CMOS process and achieves a noise figure of 4.7 dB/5.1 dB for the 2.4-GHz/5-GHz bands, respectively. The receiver front-end provides a dual gain mode of 5 dB/30 dB with an IIP3 of -1dBm for the low gain mode. The front-end draws 25 mA/27 mA from a 1.8-V supply for the 2.4-GHz/5-GHz bands, respectively.     

An auto-I/Q calibrated CMOS transceiver for 802.11g

The CMOS transceiver IC exploits the superheterodyne architecture to implement a low-cost RF front-end with an auto-I/Q calibration function for IEEE 802.11g. The transceiver supports I/Q gain and phase mismatch auto tuning mechanisms at both the transmitting and receiving ends, which are able to reduce the phase mismatch to within 1/spl deg/ and gain mismatch to 0.1dB. Implemented in a 0.25 /spl mu/m CMOS process with 2.7 V supply voltage, the transceiver delivers a 5.1 dB receiver cascade noise figure, 7 dBm transmit, and a 1 dB compression point.     

A low-power 2.4-GHz transmitter/receiver CMOS IC

A 2.4-GHz CMOS receiver/transmitter incorporates circuit stacking and noninvasive baseband filtering to achieve a high sensitivity with low power dissipation. Using a single 1.6-GHz local oscillator, the transceiver employs two upconversion and downconversion stages while providing on-chip image rejection filtering. Realized in a 0.25-/spl mu/m digital CMOS technology, the receiver exhibits a noise figure of 6 dB and consumes 17.5 mW from a 2.5-V supply, and the transmitter delivers an output power of 0 dBm with a power consumption of 16 mW.     

A 3-V, 0.35-/spl mu/m CMOS Bluetooth receiver IC

A fully integrated CMOS low-IF Bluetooth receiver is presented. The receiver consists of a radio frequency (RF) front end, a phase-locked loop (PLL), an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, and a frequency offset cancellation circuit. The highlights of the receiver include a low-power active complex filter with a nonconventional tuning scheme and a high-performance mixed-mode GFSK demodulator. The chip was fabricated on a 6.25-mm/sup 2/ die using TSMC 0.35-/spl mu/m standard CMOS process. -82 dBm sensitivity at 1e-3 bit error rate, -10 dBm IIP3, and 15 dB noise figure were achieved in the measurements. The receiver active current is about 65 mA from a 3-V power supply.     

A fully monolithic 260-/spl mu/W, 1-GHz subthreshold low noise amplifier

A micro-power complementary metal oxide semiconductor (CMOS) low-noise amplifier (LNA) is presented based on subthreshold MOS operation in the GHz range. The LNA is fabricated in an 0.18-/spl mu/m CMOS process and has a gain of 13.6 dB at 1 GHz while drawing 260 /spl mu/A from a 1-V supply. An unrestrained bias technique, that automatically increases bias currents at high input power levels, is used to raise the input P1dB to -0.2 dBm. The LNA has a measured noise figure of 4.6 dB and an IIP3 of 7.2 dBm.     

A 5.25-GHz image rejection RF front-End Receiver With Polyphase filters

A 5.25-GHz image rejection (IR) radio frequency (RF) front-end receiver is proposed, which is implemented in 0.18-/spl mu/m CMOS technology. The proposed receiver adopts both a high-intermediate frequency (IF) and the double quadrature architecture to achieve high IR at 5-GHz frequency. The measured results show a power gain of 14 dB, a minimum noise figure of 7.9dB, and IIP3 of -8dBm. The measured maximum image rejection ratio is 45dBc. The receiver consumes a total of 32mA from a 1.8-V supply.     

A 2-GHz CMOS image-reject receiver with LMS calibration

This paper describes a sign-sign least-mean squares (LMS) technique to calibrate gain and phase errors in the signal path of a Weaver image-reject receiver. The calibration occurs at startup and the results are stored digitally, allowing continuous signal reception thereafter. Fabricated in a standard digital 0.25-/spl mu/m CMOS technology, the receiver achieves an image-rejection ratio of 57 dB after calibration, a noise figure of 5.2 dB, and a third-order input intercept point of -17 dBm. The circuit consumes 55 mW in calibration mode and 50 mW in normal receiver mode from a 2.5-V power supply. The prototype occupies an area of 1.23 /spl times/ 1.84 mm/sup 2/.     

A 1.8-V 10-Gb/s fully integrated CMOS optical receiver analog front-end

A fully integrated 10-Gb/s optical receiver analog front-end (AFE) design that includes a transimpedance amplifier (TIA) and a limiting amplifier (LA) is demonstrated to require less chip area and is suitable for both low-cost and low-voltage applications. The AFE is fabricated using a 0.18-/spl mu/m CMOS technology. The tiny photo current received by the receiver AFE is amplified to a differential voltage swing of 400 mV/sub (pp)/. In order to avoid off-chip noise interference, the TIA and LA are dc-coupled on the chip instead of ac-coupled though a large external capacitor. The receiver front-end provides a conversion gain of up to 87 dB/spl Omega/ and -3dB bandwidth of 7.6 GHz. The measured sensitivity of the optical receiver is -12dBm at a bit-error rate of 10/sup -12/ with a 2/sup 31/-1 pseudorandom test pattern. Three-dimensional symmetric transformers are utilized in the AFE design for bandwidth enhancement. Operating under a 1.8-V supply, the power dissipation is 210 mW, and the chip size is 1028 /spl mu/m/spl times/1796 /spl mu/m.     

A single-chip dual-band tri-mode CMOS transceiver for IEEE 802.11a/b/g wireless LAN

A single-chip dual-band tri-mode CMOS transceiver that implements the RF and analog front-end for an IEEE 802.11a/b/g wireless LAN is described. The chip is implemented in a 0.25-/spl mu/m CMOS technology and occupies a total silicon area of 23 mm/sup 2/. The IC transmits 9 dBm/8 dBm error vector magnitude (EVM)-compliant output power for a 64-QAM OFDM signal. The overall receiver noise figure is 5.5/4.5 dB at 5 GHz/2.4 GHz. The phase noise is -105 dBc/Hz at a 10-kHz offset and the spurs are below -64 dBc when measured at the 5-GHz transmitter output.     

A 0.13 /spl mu/m CMOS front-end, for DCS1800/UMTS/802.11b-g with multiband positive feedback low-noise amplifier

This paper presents a fully integrated CMOS receiver front-end based on a direct conversion architecture for UMTS/802.11b-g and a low-IF architecture at 100 kHz for DCS1800. The two key building blocks are a multiband low-noise amplifier (LNA) that uses positive feedback to improve its gain and a highly linear mixer. The front-end, integrated in a 0.13 /spl mu/m CMOS process, exhibits a minimum noise figure of 5.2 dB, a programmable gain that can be varied from 13.5 to 28.5 dB, an IIP3 of more than -7.5 dBm and an IIP2 better than 50 dBm. The total current consumption is 20mA from a 1.2V supply.     

A UWB CMOS transceiver

A direct-conversion ultra-wideband (UWB) transceiver for Mode 1 OFDM applications employs three resonant networks and three phase-locked loops. Using a common-gate input stage, the receiver allows direct sharing of the antenna with the transmitter. Designed in 0.13-/spl mu/m CMOS technology, the transceiver provides a total gain of 69-73 dB and a noise figure of 6.5-8.4 dB across three bands, and a TX 1-dB compression point of -10 dBm. The circuit consumes 105 mW from a 1.5-V supply.     

A merged CMOS LNA and mixer for a WCDMA receiver

A low-noise amplifier (LNA) and mixer circuit in 0.35-/spl mu/m CMOS operates at 2.1 GHz. Merging the LNA and mixer lowers the number of transistors in the signal path and thereby also the nonlinearity and power consumption. The circuit meets the specifications for a direct conversion wide-band code-division multiple access (WCDMA) receiver. Its noise figure is 3.4 dB (5kHz to 5MHz), the total conversion gain is 23 dB, the third-order input-referred intercept point is -1.5 dBm, and the local oscillator leakage to the antenna is less than -71 dBm. The fully differential circuit takes 8 mA from a 2.7-V supply.     

An interference-robust receiver for ultra-wideband radio in SiGe BiCMOS technology

A 3.1-4.8 GHz ultra-wideband (UWB) receiver front-end for high data rate, short-range communication is presented. The receiver, based on the Multi Band OFDM Alliance (MBOA) standard proposal, consists of a zero-IF receive chain and an ultra-fast frequency-hopping synthesizer. The combination of high-linearity RF circuits, aggressive baseband filtering and low local oscillator spurs from the synthesizer results in an interference-robust receiver, having the ability to co-exist with systems operating in the 2.4-GHz and 5-GHz ISM bands. The packaged device shows an overall noise figure of 4.5 dB and has a measured input IP3 of -6 dBm and input IP2 of +25 dBm. Spurious tones generated by the synthesizer are below -45 dBc and -50 dBc in the 2.4-GHz and 5-GHz ISM bands, respectively. The hopping speed is well below the required 9.5 ns. The complete receive chain has been realized in a 0.25 /spl mu/m BiCMOS technology and draws 78mA from a 2.5-V supply.