Synthesis of Al2O3/TiCN-0.2%Y2O3 Composite by Hot Pressing

Al2O3/TiCN composites were synthesized by hot pressing.The influences of components and HP temperature on mechanical properties,such as bending strength,breaking tenacity and Vickers hardness were investigated.The results showed that the mechanical properties of Al2O3/TiCN composite increased with temperature when hot pressing temperature is below 1650 ℃.The mechanical properties reached their maximums when the composites were sintered at 1650 ℃ for 30 min under hot pressing pressure of 35 MPa,the value of bending strength,breaking tenacity and Vickers hardness was 1015 MPa,6.89 MPa·m1/2,and 20.82 MPa,respectively.When hot pressing temperature was above 1650 ℃,density decreased because of decomposition with increased temperature,and mechanical properties dropped because of rapid growth of grains in size at high temperature.Microstructure analysis showed that the addition of Y2O3 led to the formation of YAG phase so as to inhibit the growth of crystals.This helped to improve breaking tenacity of the composites.TiCN particles with diameters of 1 μm dispersed at Al2O3 grain boundaries,inhibited grain growth and enhanced mechanical properties of the composites.SEM study of the propagation of indentation cracks showed that the bridge linking behavior between matrix and strengthening phase might lead to the formation of the coexisted field of crack deflection,branching and bridge linking.The mechanism of this phenomenon was that the addition of Y2O3 improved the dispersion of TiCN particles so as to enhance the tenacity of the composites.The breaking tenacity was changed from 5.94 to 6.89 MPa·m1/2.     

Investigation on pumping oxygen characteristics of （Bi2O3）0.73（Y2O3）0.27 solid electrolyte

（Bi2O3）0.73（Y2O3）0.27 fine powders prepared by wet chemical precipitation method were cold isostatically pressed to form solid electrolyte tubes, and sintered at 900 ℃ for 10 h in the air. Their pumping oxygen characteristics in non-dehydrated Ar gas were investigated, where a ZrO2 （Y2O3 stabilized） oxygen sensor was used to measure the oxygen partial pressure Po2. The results showed that the Po2 value reached magnitudes of 1×10^-2-1×10^-10 Pa at the applied pumping oxygen voltage of 0.5 V, 1×10^-37-1×10^-27 Pa at 1.0 V and 1×10^-53-1×10^47 Pa at 2.0 V within the temperature range from 550 to 650 ℃. Moreover, no cracks were found in the tested solid electrolyte tubes. Thus, the Bi2O3-Y2O3 system might be used in solid electrolyte oxygen pump for purifying gases.     

Stability of 3CaO · Al2O3 · 6H2O in KOH + K2CO3 + H2O system for chromate production

In the novel clean chromate production process, the alkali liquor recycled to decompose the chromite ore mainly consists of KOH and K₂CO₃ which accumulates aluminium impurity and affects the quality of the product greatly. Aluminium impurity can be removed by adding CaO to precipitate as 3CaO · Al₂O₃ · 6H₂O (C₃AH₆). A study of the effects of various parameters, such as KOH concentration, K₂CO₃ concentration and temperature on the behaviour of C₃AH₆ show that C₃AH₆ is decomposed to 3CaO · Al₂O₃ · CaCO₃ · 11H₂O and CaCO₃ below 150 g L^− 1 KOH, and decomposed to Ca(OH)₂ above 150 g L^− 1 KOH. With K₂CO₃ concentration increasing, C₃AH₆ decomposes significantly, which results in more CaCO₃ or 3CaO · Al₂O₃ · CaCO₃ · 11H₂O produced. Temperature has a large positive effect on the decomposition of C₃AH₆ at 45 g L^− 1 KOH but has no significant effect at 150 g L^− 1 KOH. The optimal condition for removing aluminium impurity in the KOH + K₂CO₃ + H₂O system is 150 g L^− 1 KOH, 50 g L^− 1 K₂CO₃ and 80 °C.     

Features of solid solution formation with a fluorite type structure in the system ZrO2-HfO2-Y2O3 with different synthesis methods

X-ray phase, petrographic, and thermal analysis methods are used to study the properties of solid solutions with a fluorite type structure in the ternary system ZrO₂-HfO₂-Y₂O₃ in relationship to preparation method: mixing of the original powders followed by solid-phase sintering and melting in solar furnaces; hydrothermal synthesis of nanocrystalline powders followed by solid-phase sintering. It is shown that in specimens whose composition lies at the isoconcentrate of 10 mole% Y₂O₃ a single phase forms independent of preparation method, i.e. a solid solution with a fluorite type structure. The azeotrope, situated at the liquidus of the limiting binary system ZrO₂-Y₂O₃ in the region of fluorite-like solid solutions, affects the melting temperature of ternary solid solutions and the lattice parameters of specimens after melting in a solar furnace. __________ Translated from Poroshkovaya Metallurgiya, Nos. 1–2(447), pp. 3–11, January–February, 2006.     

Preparation and Characterization of Gd3Sc2Ga3O12 Polycrystalline Material by Co-Precipitation Method

Gd3Sc2Ga3O12 polycrystalline material for single crystal growth was prepared with Ga, Gd2O3 and Sc2O3 as starting materials and aqueous ammonia as the precipitator by co-precipitation method. The precursors sintered at various temperatures were characterized by infrared spectra （IR）, X-ray diffractometry （XRD） and transmitted electron microscopy （TEM）. The results showed that pure GSGG phase could be obtained at 900 ℃. The sintered powders were well-dispersed and less-aggregated in the sintered temperature range of 900 - 1000 ℃. XRD and TEM show that the polycrystalline particle sizes of the polycrystalline powders were about 20 - 50 nm. Compared with the method that Ga2O3, Gd2O3 and Sc2O3 were mixed directly and sintered to get polycrystalline materials, the synthesized temperature was lower and sintered time was shorter. Thus co-precipitation was a good method to synthesize GSGG polycrystalline material.     

Study on Sulfation of CeO2/γ-Al2O3 Sorbent in Simulated Flue Gas

It is well known that sulfur dioxide(SO2) , morethan50%of which arise fromcombustion of fossil fu-els ,are precursors of acidrain andtheir emission pos-es a global threat tothe atmosphere .Environmental a-gencies have ,therefore ,regulated emissions of SO…     

Effects of stabilization of ZrO2 by REM oxides in Al2O3-ZrO2 compositions

Conclusions Melting and high-rate quenching the melt of the Al₂O₃-ZrO₂-REM oxide melt results in the formation of a heterogeneous material with a highly homogenized structure in which the oxides/ stabilizers are completely dissolved in ZrO₂. Mechanical dispersion (vibrogrinding) of the granules and subsequent heat treatment of the specimens compacted from these powders lead to partial destabilization of the solid solutions based on ZrO₂. An exception is represented by the (Al₂O₃-ZrO₂)-Y₂O₃ and (Al₂O₃-ZrO₂)-Sc₂O₃ compositions. High temperature cause recrystallization growth of structural components and coarsening of the eutectic structure of all compositions. The highest stability was recorded for the composition in which ZrO₂ is stabilized by the yttrium oxides.Translated from Poroshkovaya Metallurgiya, No. 11(323) pp. 52–55, November, 1989.     

Thermochemical Study on Ternary Solid Complex of La(Gly)2 (Ala)3 Cl3 ·2H2O (s)

The complex of lanthanum chloride with Glycine and Alanine, La(Gly)₂(Ala)₃Cl₃ · 2H₂O, was synthesized and characterized by IR, elementary analysis, thermogravimetric analysis, and chemical analysis. The dissolution enthalpies of LaCl₃ · 7H₂O(s), 2Gly(s) + 3Ala(s) and La(Gly)₂(Ala)₃Cl₃ · 2H₂O(s) were determined in 2 mol · L⁻¹ HCl by a solution-reaction isoperibol calorimeter. By designing a thermochemical cycle in terms of Hess' Law and through calculation, the reaction enthalpy of lanthanum chloride seven-hydrate with Glycine and Alanine was obtained: Δ_rH^θ_m(298.15 K) = (29.652 ± 0.504) kJ · mol⁻¹, and the standard enthalpy of formation of La(Gly)₂(Ala)₃Cl₃ · 2H₂O(s) Δ_fH^θ_m[La(Gly)₂ (Ala)₃Cl₃ · 2H₂O, s, 298.15 K] = −4467.6 ± 8.3 kJ · mol⁻¹.     

Luminescent properties of amorphous phosphor 1.4YeO3·2.5Al2O3·0.1Tb2O3 prepared by sol-gel method

Amorphous phosphor 1.4YeO3·2.5Al2O3·0.1Tb2O3 （the same composition as Y2.8Tb0.2Al5O12） was prepared via a sol-gel method at relatively low temperature （i.e., below 650℃）, which is much lower than that for the preparation of polycrystalline Y3Al5O12：Tb^3＋ （above 1400℃）. The amorphous phosphor prepared in the optimized conditions showed a bright green-yellowish luminescence, the intensity of which was comparable with that of polycrystalline sample and the emissions of which were assigned to 5D4 → 7Fj transitions of Tb^3＋. Besides the emissions of Tb^3＋, the amorphous samples prepared at temperatures below 500 ℃ presented a weak blue emission band around 420 nm.     

High Temperature Chemical Reaction of La2O3 in H3BO3 -C System

The high temperature chemical reaction process of La2O3 in H3BO3-C system was studied by means of XRD and TG-DTA.The results showed that dehydration reaction of H3BO3 occurred in the temperature range of 82～390 ℃;La2O3 and B2O3 reacted to form LaB3O6,LaBO3,and B4C in the temperature range of 836～1400℃;at 1450 ℃,B4C and LaBO3 further reacted to form LaB4,and partial LaB4 and B reacted to form LaB6;at 1500 ℃,LaB4 and B reacting into LaB6 was the main reaction,and the content of LaB6 increased with prolonging time.     

Microstructure and Electrical Properties of Er2O3-Doped ZnO-Based Varistor Ceramics Prepared by High-Energy Ball Milling

The microstructure, electrical properties and density of ZnO-based varistor ceramics with different Er2O3 content prepared by high-energy ball milling （HEBM） and sintered at 800℃ were investigated. With increasing Er2O3 content, the ZnO grain size decreases due to the Er-rich phases inhibiting grain growth ; and nonlinear coefficient （ α ） decreases because of the decrease of barrier height （φB） The breakdown voltage （Eb） and density increase, whereas leakage current （IL） decreases with increasing Er2O3 content. The barrier height （φB）, donor concentration （Nd）, density of interface states （Ns） decrease and barrier width （ω） increases with increasing Er2O3 content due to acceptor effect of Er2O3 in varistor ceramics.     

Ti-Y2O3 Composites with Nanocrystalline and Microcrystalline Matrix

Mechanical milling of a Ti-2 pct Y₂O₃ powders mixture led to the synthesizing of a composite powder with a nanocrystalline Ti matrix having a mean crystallite size of 19 nm. Both the nanocomposite powder prepared through milling and the initial mixture of powders were consolidated by hot pressing under the pressure of 7.7 GPa at the temperature of 1273 K (1000 °C). The transmission electron microscopy (TEM) investigations of the bulk sample produced from milled powder revealed that Y₂O₃ equiaxial particles of less than 30 nm in size are distributed uniformly in the Ti matrix with a grain size in the wide range from 50 nm to 200 nm. The microhardness of the produced nanocrystalline material is 655 HV0.2, and it significantly exceeds the hardness of the microcrystalline material (the consolidated initial mixture of powders), which is equal to 273 HV0.2. This finding confirms that reducing the grain size to the nanometric level can have a beneficial influence on the hardness of titanium alloys. Dispersion hardening also contributes to the hardness increase.     

Interactions in the Al2O3-ZrO2-Y2O3 system

The phase diagram of the Al₂O₃-ZrO₂ system was replotted over a broad range of concentrations (0–100 mole %) and temperatures (1150–2800°C). The polymorphic transformation of zirconium F ? T occurs via the metatectic reaction F ? T + L at 2260°C. Phase triangulation was employed to plot the diagrams of the partially quasibinary sections in the Al₂O₃-ZrO₂-Y₂O₃ system. Since there is a wide solubility range based on ZrO₂ in the binary ZrO₂-Y₂O₃ system, the triangulation conodes are displaced in the F-solid solution corners. The two-phase regions Y₃A₅-F are quite broad. The reactions in all three are of the eutectic type. The ternary solid solution fields in the Al₂O₃-ZrO₂-Y₂O₃ system had no observable width.     

Desilication of sodium aluminate solution by Friedel's salt (FS: 3CaO·A12O3·CaCl2·10H2O)

Controlling silica level in Bayer liquor is critical in order to prevent scaling or alumina quality issues. The conventional method of removing silicates from aluminate solutions requires the introduction of calcium oxide or calcium hydroxide. In this work, Friedel's salt (FS: 3CaO·A1₂O₃·CaCl₂·10H₂O) is proved for the first time to remove up to 95% silica from sodium aluminate solution. FS is a mineral anion exchanger belonging to the layered double hydroxides (LDHs) which was prepared by adding calcium chloride to sodium aluminate over the temperature range of 50–90 °C. It was characterized by XRD, SEM, Particle Size Analyzer and TG-DSC. FS prepared at 50 °C has a relatively high desilication capacity, better than calcium oxide.Experimental parameters affecting the desilication process, such as temperature, sodium aluminate liquor composition, initial silica concentration (4–10 g/L) and FS dosage were investigated in detail and a comparison of desilication between FS and CaO was carried out. The desilication products (DSP) were mainly calcium aluminium silicates, identified by XRD to be Chabazite and Wadalite and the final chloride concentration in the sodium aluminate solution after anion exchange with FS was  0.015 g/L. The rate of desilication by FS was first order with a rate constant 2.582 × 10⁶ min^− 1. The apparent activation energy was estimated to be 57.7 kJ mol^− 1 over the temperature range of 80–110 °C.     

NiO-Ce0.5Zr0.5O2 catalysts prepared by citric acid method for steam reforming of ethanol

NiO-Ce0.5Zr0.5O2 catalysts were prepared by citrate method and used for hydrogen production from steam reforming of ethanol （SRE）. The effect of nickel content and space velocity on the catalytic performance was investigated. The prepared catalysts were characterized with XRD and thermal analysis techniques. 20%NiO-Ce0.5Zr0.5O2catalyst was very active and selective for hydrogen production via SRE, in which ethanol conversion of 100% could be obtained with feed component of 20% （H2O＋EtOH） and 80% N2, water/ethanol of 3/1 in molar ratio at 350 ℃. Also, the catalyst showed good stability for anti-sintering and carbon-resistance. The XRD illuminated that both NiO and Ce0.5Zr0.5O2 crystal sizes were very small in NiO-Ce0.5Zr0.5O2 catalyst, and Ce0.5Zr0.5O2 solid solution was formed.     

Catalytic combustion of toluene over Pd-based monolithic catalysts with a novel washcoat Ce0.8Zr0.15La0.05Oδ

Two novel washcoats Ce_0.8Zr_0.15La_0.05O_δ and Ce_0.8Zr_0.2O₂ was prepared by an impregnation method, which acted as a host for the active Pd component to prepare Pd/Ce_0.8Zr_0.15La_0.05O_δ/substrate and Pd/Ce_0.8Zr_0.2O₂/substrate monolithic catalysts for toluene combustion. The washcoats was characterized by X-ray diffraction (XRD), Raman spectroscopy, Brunauner-Emmett-Teller (BET), and H₂-temperature-programmed reduction (H₂-TPR). The result indicated that both the washcoats had strong vibration-shock resistance according to ultrasonic test. Doping La³⁺ into CeO₂-ZrO₂ solid solution could generate more oxygen vacancies, and could inhibit the sinter of CeO₂-ZrO₂ solid solution when calcined at high temperatures (800, 900 and 1000 °C). The washcoat Ce_0.8Zr_0.15La_0.05O_δ had much better redox properties. The reductive temperature of Ce⁴⁺ species shifted to low temperature by 60 °C when the washcoats calcined at high temperatures (800, 900 and 1000 °C). The Pd/Ce_0.8Zr_0.15La_0.05O_δ/substrate monolithic catalyst calcination at 500 °C had the best catalytic activity and the 95% toluene conversion at a temperature as low as 190 °C. When calcined at low temperature (500 and 700 °C), the catalytic activity has little improvement, however, when calcined at high temperature, the catalytic activity of Pd/Ce_0.8Zr_0.15La_0.05O_δ/substrate monolithic catalysts had significant improvement. As catalyst washcoat, the Ce_0.8Zr_0.15La_0.05O_δ had better thermal stability than the washcoat Ce_0.8Zr_0.2O₂, the developed Pd/Ce_0.8Zr_0.15La_0.05O_δ/substrate monolithic catalyst in this work was promising for eliminating Volatile organic compounds.     

Combustion synthesis of α-Si3N4-(MgO, Y2O3) composites

The possibility of obtaining composite powders of α-Si₃N₄-Y₂O₃ and α-Si₃N₄-MgO by self-propagating high-temperature synthesis (SHS) is studied. It is established that the α → β phase transformation starts at temperatures lower than the melting points of the corresponding eutectics. Metastable composite powders based on α-Si₃N₄ with a high rate of phase transition are obtained. The composite powders (α-Si₃N₄-Y₂O₃, α-Si₃N₄-MgO) are used in hot pressing technology. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 10–14, 2007.     

Partial oxidation of methane on Ni/CeO2-ZrO2/γ-Al2O3 prepared using different processes

The influences of CeO2-ZrO2 and γ-Al2O3 mixing methods on the catalytic activity and stability of partial oxidation of methane （POM） were investigated over Ni/Ce0.7Zr0.3O2-Al2O3 catalysts. The catalysts were characterized by XRD, TPR, H2-chemsorption, and TG-DTA. For fresh catalysts, the results showed that the salt precursor mixing catalyst （ATOM） presented better performance than the catalysts prepared by the precipitator mixing method （MOL） and the powder mechanically mixing method （MECH）. The result of XRD suggested that the interaction between CeO2-ZrO2 and Al2O3 in ATOM sample was stronger than the others, which led to more lattice defects and thereby better initial activity. Moreover, the MECH sample had the best stability and the least coke deposition in 24 h stability tests. The results of TPR and H2-chemsorption indicated that the intimate contact of Ni-Al in MECH sample enhanced the ability of resisting coke deposition and metal sintering.     

Vacuum ultraviolet excited photoluminescence properties of Gd2O2CO3：Eu^3＋ phosphor

The Gd2O2CO3：Eu^3＋ with type-Ⅱ structure phosphor was successfully synthesized via flux method at 400 ℃ and their photoluminescence properties in vacuum ultraviolet （VUV） region were examined. The broad and strong excitation bands in the range of 153-205 nm owing to the CO3^2- host absorption and charge transfer （CT） of Gd^3＋-O2^- were observed for Gd2O2CO3：Eu^3＋. Under 172 nm excitation, Gd2O2CO3：Eu^3＋ exhibited strong red emission with good color purity, indicating Eu^3＋ ions located at low symmetry sites and the chromaticity coordination of luminescence for Gd2O2CO3：Eu^3＋ was （x=0.652, y=0.345）. The photoluminescence quenching concentration of Eu^3＋ excited by 172 nm for Gd2O2CO3：Eu^3＋ was about 5%. Gd2O2CO3：Eu^3＋ would be a potential VUV-excited red phosphor applied in mercury-free fluorescent lamps.