CO2 capture capacity of CaO in long series of pressure swing sorption cycles

One promising method for the capture of CO₂ from point sources is through the usage of a lime-based sorbent. Lime (CaO) acts as a CO₂ carrier, absorbing CO₂ from the flue gas (carbonation) and releasing it in a separate reactor (calcination) to create a pure stream of CO₂ suitable for sequestration. One of the challenges with this process is the decay in calcium utilization (CO₂ capture capacity) during carbonation/calcination cycling. The reduction in calcium utilization of natural limestone over large numbers of cycles (>250) was studied. Cycling was accomplished using pressure swing CO₂ adsorption in a pressurized thermogravimetric reactor (PTGA). The effect of carbonation pressure on calcium utilization was studied in CO₂ with the reactor operated at 1000 °C. The pressure was cycled between atmospheric pressure for calcination, and 6, 11 or 21 bar for carbonation. Over the first 250 cycles, the calcium utilization reached a near-asymptotic value of 12.5-27.7%, depending on the cycling conditions. Pressure cycling resulted in improved long-term calcium utilization compared to temperature swing or CO₂ partial pressure swing adsorption under similar conditions. An increased rate of de-pressurization caused an increase in calcium utilization, attributed to fracturing of the sorbent particle during the rapid calcination, as observed via SEM analysis.     

CO2 uptake of modified calcium-based sorbents in a pressurized carbonation-calcination looping

This study focuses on enhancing CO₂ uptake by modifying limestone with acetate solutions under pressurized carbonation condition. The multicycle tests were carried out in an atmospheric calcination/pressurized carbonation reactor system at different temperatures and pressures. The pore structure characteristics (BET and BJH) were measured as a supplement to the reaction studies. Compared with the raw limestone, the modified sorbent showed a great improvement in CO₂ uptake at the same reaction condition. The highest CO₂ uptake was obtained at 700 °C and 0.5 MPa, by 88.5% increase over the limestone at 0.1 MPa after 10 cycles. The structure characteristics of the sorbents on N₂ absorption and SEM confirm that compared with the modified sorbent, the effective pores of limestone are greatly driven off by sintering, which hinders the easy access of CO₂ molecules to the unreacted-active sites of CaO. The morphological and structural properties of the modified sorbent did not reveal significant differences after multiple cycles. This would explain its superior performance of CO₂ uptake under pressurized carbonation. Even after 10 cycles, the modified sorbent still achieved a CO₂ uptake of 0.88.     

烟气中水蒸气对钙基吸收剂碳酸化的影响特性

在循环煅烧/碳酸化反应系统上考察煅烧气氛和碳酸化气氛中水蒸气含量以及CO₂分压对钙基吸收剂成型颗粒碳酸化的影响,通过对钙基吸收剂微观结构分析(扫描电镜、氮吸附分析)以理解水蒸气影响碳酸化特性的机理。结果表明,煅烧气氛和碳酸化气氛中的水蒸气均可提高钙基吸收剂的碳酸化转化率,水蒸气含量分别为10%和5%时,吸收剂的碳酸化性能较好;水蒸气在碳酸化气氛中对高铝水泥改性吸收剂的改善作用较石灰石显著。煅烧气氛中的CO₂分压越高,烧结现象越严重,降低钙基吸收剂的捕集效率;碳酸化气氛CO₂分压提高,有利于提高钙基吸收剂的碳酸化转化率。烟气中水蒸气丰富了吸收剂的微观孔隙,使得吸收剂捕集CO₂性能得到改善。     

铵基循环碳酸化固定CO2

引言由煤等化石燃料燃烧产生的温室气体CO2的捕集与封存已引起国际社会的广泛关注[1-2];其中,模仿自然界钙镁硅酸盐矿物风化过程的碳酸化固定是实现大规模封存CO2的重要途径,与其他封存技术相比,碳酸化固定CO2环境风险性小,并可     

Enhancement of Ca‐Based Sorbent Multicyclic Behavior in Ca Looping Process for CO2 Separation

The Ca‐based sorbent looping cycle represents an innovative way of CO₂ capture for power plants. However, the CO₂ capture capacity of the Ca‐based sorbent decays sharply with calcination/carbonation cycle number increasing. In order to improve the CO₂ capture capacity of the sorbent in the Ca looping cycle, limestone was modified with acetic acid solution. The cyclic carbonation behaviors of the modified and original limestones were investigated in a twin fixed‐bed reactor system. The modified limestone possesses better cyclic carbonation kinetics than the original limestone at each cycle. The modified limestone carbonated at 640–660 °C achieves the optimum carbonation conversion. The acetic acid modification improves the long‐term performance of limestone, resulting in directly measured conversion as high as 0.4 after 100 cycles, while the original limestone remains at a conversion of less than 0.1 at the same reaction conditions. Both the pore volume and pore area distributions of the calcines derived from the modified limestone are better than those derived from the original limestone. The CO₂ partial pressure for carbonation has greater effect on conversion of the original limestone than on that of the modified sorbent because of the difference in their pore structure characteristics. The carbonation conversion of the original limestone decreases with the increase in particle size, while the change in particle size of the modified sorbent has no clear effect on cyclic carbonation behavior.     

Sulphation and carbonation properties of hydrated sorbents from a fluidized bed CO2 looping cycle reactor

Sulphation and carbonation have been performed on hydrated spent residues from a 75 kW_th dual fluidized bed combustion (FBC) pilot plant operating as a CO₂ looping cycle unit. The sulphation and carbonation tests were done in an atmospheric pressure thermogravimetric analyzer (TGA), with the sulphation performed using synthetic flue gas (0.45% SO₂, 3% O₂, 15% CO₂ and N₂ balance). Additional tests were carried out in a tube furnace (TF) with a higher SO₂ concentration (1%) and conversions were determined by quantitative X-ray diffraction (QXRD) analyses. The morphology of the sulphated samples from the TF was examined by scanning electron microscopy (SEM). Sulphation tests were performed at 850 °C for 150 min and carbonation tests at 750 °C, 10 cycles for 15 min (7.5 min calcination + 7.5 min carbonation). Sulphation conversions obtained for the hydrated samples depended on sample type: in the TGA, they were ～75–85% (higher values were obtained for samples from the carbonator); and in the TF, values around 90% and 70% for sample from carbonator and calciner, respectively, were achieved, in comparison to the 40% conversion seen with the original sample. The SEM analyses showed significant residual porosity that can increase total conversion with longer sulphation time. The carbonation tests showed a smaller influence of the sample type and typical conversions after 10 cycles were 50% – about 10% higher than that for the original sample. The influence of hydration duration, in the range of 15–60 min, is not apparent, indicating that samples are ready for use for either SO₂ retention, or further CO₂ capture after at most 15 min using saturated steam. The present results show that, upon hydration, spent residues from FBC CO₂ capture cycles are good sorbents for both SO₂ retention and additional CO₂ capture.     

Application of the random pore model to the carbonation cyclic reaction

Calcium oxide has been proved to be a suitable sorbent for high temperature CO₂ capture processes based on the cyclic carbonation‐calcination reaction. It is important to have reaction rate models that are able to describe the behavior of CaO particles with respect to the carbonation reaction. Fresh calcined lime is known to be a reactive solid toward carbonation, but the average sorbent particle in a CaO‐based CO₂ capture system experiences many carbonation‐calcination cycles and the reactivity changes with the number of cycles. This study applies the random pore model (RPM) to estimate the intrinsic rate parameters for the carbonation reaction and develops a simple model to calculate particle conversion with time as a function of the number of cycles, partial pressure of CO₂, and temperature. This version of the RPM model integrates knowledge obtained in earlier works on intrinsic carbonation rates, critical product layer thickness, and pore structure evolution in highly cycled particles. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Enhancement of reactivity in surfactant-modified sorbent for CO2 capture in pressurized carbonation

The calcination/carbonation loop of calcium-based (Ca-based) sorbents is considered as a viable technique for CO₂ capture from combustion gases. Recent attempts to improve the CO₂ uptake of Ca-based sorbents by adding calcium lignosulfonate (CLS) with hydration have succeeded in enhancing its effectiveness. The optimum mass ratio of CLS/CaO is 0.5 wt.%. The reduction in particle size and grain size of CaO appeared to be parts of the reasons for increase in CO₂ capture. The primary cause of increase in reactivity of the modified sorbents was the ability of the CLS to retard the sintering rate and thus to remain surface area and pore volume for reaction. The CO₂ uptake of the modified sorbents was also enhanced by elevating the carbonation pressure. Experimental results indicate that the optimal reaction condition of the modified sorbents is at 0.5 MPa and 700 °C and a high conversion of 0.7 is achieved after 10 cycles, by 30% higher than that of original limestone, at the same condition.     

Effect of attrition on particle size distribution and SO2 capture in fluidized bed combustion under high CO2 partial pressure conditions

In both pressurized and oxygen-enriched fluidized bed combustion the partial pressure of CO₂ in the reactor becomes high, which affects SO₂ capture by limestone. Both of these technologies are also applicable to decreasing greenhouse gas emissions; the first one by increasing the efficiency of electric energy production and the latter by enabling capture of carbon dioxide for storage.Attrition increases the reaction rate by removing the sulphated layer on the particle, thus reducing the diffusion resistance. In the well-known solution for the shrinking core model the reaction time can be presented as the sum of the contributions of the kinetics and diffusion. It is shown that the effect of attrition can be expressed as an auxiliary term in this expression. A method to extract the diffusivity of the product layer from the SO₂ response in a bench-scale fluidized bed test using a limestone sample with a wide particle size distribution is presented. Based on a population balance model, a method to estimate the particle-size-dependent attrition rate from measured particle size distributions of the feed and bed material is illustrated for a 71-MW_e pressurized power plant. In addition attrition and its effect on the optimization of the limestone particle size for sulphur capture in oxygen-enriched combustion are discussed.     

Sulfation Rates of Particles in Calcium Looping Reactors

The sulfation reaction rate of CaO particles in three reactors comprising a post‐combustion calcium looping system is discussed: a combustion chamber generating flue gases, a carbonator reactor to capture CO₂ and SO₂, and an oxy‐fired calciner to regenerate the CO₂ sorbent. Due to its strong impact on the pore size distribution of CaO particles, the number of carbonation/calcination cycles arises as a new important variable to understand sulfation phenomena. Sulfation patterns change as a result of particle cycling, becoming more homogeneous with higher number of cycles. Experimental results from thermogravimetric tests demonstrate that high sulfation rates can be measured under all conditions tested, indicating that the calcium looping systems will be extremely efficient in SO₂ capture.     

A simplified model of SO2 capture by limestone in 71 MWe pressurized fluidized bed combustor

A mathematical model of SO₂ capture by uncalcined limestone particles with solid attrition under pressurized fluidized bed combustion conditions was developed based on the shrinking unreacted-core model. Since the thickness of the product layer is sufficiently much smaller than the particle size, a flat surface model was employed. The difference in SO₂ capture behavior between continuous solid attrition and intermittent attrition was investigated. The reaction rate for intermittent solid attrition was found to be lower than that for continuous attrition mode under low SO₂ concentration conditions. A simple mathematical expression to calculate reaction rate of SO₂ capture per unit external surface area of limestone is proposed.The present simplified mathematical model of SO₂ capture by single limestone particle under periodical attrition conditions was applied to the analysis of a large-scale pressurized fluidized bed combustor. By giving the period of attrition as a parameter, the experimental results agreed well with the model results. From the vertical concentration profile of SO₂ concentration, the emission of SO₂ was found to be governed by the balance between SO₂ formation rate from char and SO₂ capture by limestone at the upper surface of the dense bed. A simplified expression to estimate SO₂ emission from pressurized fluidized bed combustors was proposed.     

Sequential SO2/CO2 capture enhanced by steam reactivation of a CaO-based sorbent

The steam hydration reactivation characteristics of three limestone samples after multiple CO₂ looping cycles are presented here. The CO₂ cycles were performed in a tube furnace (TF) and the resulting samples were hydrated by steam in a pressure reactor (PR). The reactivation was performed with spent samples after carbonation and calcination stages. The reactivation tests were done with a saturated steam pressure at 200 °C and also at atmospheric pressure and 100 °C. The characteristics of the reactivation samples were examined using BET and BJH pore characterization (for the original and spent samples, and samples reactivated under different conditions) and also by means of a thermogravimetric analyzer (TGA). The levels of hydration achieved by the reactivated samples were determined as well as the conversions during sulphation and multiple carbonation cycles. It was found that the presence of a CaCO₃ layer strongly hinders sorbent hydration and adversely affects the properties of the reactivated sorbent with regard to its behavior in sulphation and multiple carbonation cycles. Here, hydration of calcined samples under pressure is the most effective method to produce superior sulphur sorbents. However, reactivation of calcined samples under atmospheric conditions also produces sorbents with significantly better properties in comparison to those of the original sorbents. These results show that separate CO₂ capture and SO₂ retention in fluidized bed systems enhanced by steam reactivation is promising even for atmospheric conditions if the material for hydration is taken from the calciner.     

Carbonation reaction of lime, kinetics at ambient temperature

The uptake of carbon dioxide due to the carbonation reaction of Ca(OH)₂ in ambient temperature of approximately 20 °C has been studied. Different types of lime have been used and the CO₂ concentration has been varied to identify the influence of different variables on the kinetics of the reaction. A closed loop system has been developed and validated that allows measurement of the carbonation progress directly from monitoring CO₂ uptake. Thermal analysis (TA) was used to verify the degree of carbonation that reached up to 83%. Factor analysis on the data set has demonstrated that reaction speed is not dependent upon the CO₂ concentration within the limits tested. Carbonation speed depends on the specific surface of the lime. The results of this study contribute to research carried out on lime mortar carbonation models and on the carbonation process in general.     

钙基CO2吸收剂的循环特性

对钙基CO₂吸收剂的循环特性进行了实验研究,考察了煅烧温度和碳酸化（吸收）温度对吸收剂最大转化率的影响,比较了常压煅烧-碳酸化（CC）过程和煅烧-水合-碳酸化（CHC）过程中吸收剂的最大吸收能力,并就添加剂对吸收剂循环性能的影响进行了实验研究.结果表明,随着循环次数的增加,吸收剂的吸收能力明显下降,未经处理的吸收剂,循环10次后,其吸收能力基本都下降到20％左右;温和的煅烧温度和较高的吸收温度下,吸收剂的最大转化率比较高;CC过程中吸收剂的最大转化率明显低于CHC过程;添加了氯化钠和碳酸钠的吸收剂的吸收能力急剧下降,但循环性能稳定;多次循环后对吸收剂进行再活化,可使其活性恢复到初始的95％.     

Economical assessment of competitive enhanced limestones for CO2 capture cycles in power plants

CO₂ capture systems based on the carbonation/calcination loop have gained rapid interest due to promising carbonator CO₂ capture efficiency, low sorbent cost and no flue gases treatment is required before entering the system. These features together result in a competitively low cost CO₂ capture system. Among the key variables that influence the performance of these systems and their integration with power plants, the carbonation conversion of the sorbent and the heat requirement at calciner are the most relevant. Both variables are mainly influenced by CaO/CO₂ ratio and make-up flow of solids. New sorbents are under development to reduce the decay of their carbonation conversion with cycles. The aim of this study is to assess the competitiveness of new limestones with enhanced sorption behaviour applied to carbonation/calcination cycle integrated with a power plant, compared to raw limestone. The existence of an upper limit for the maximum average capture capacity of CaO has been considered. Above this limit, improving sorbent capture capacity does not lead to the corresponding increase in capture efficiency and, thus, reduction of CO₂ avoided cost is not observed. Simulations calculate the maximum price for enhanced sorbents to achieve a reduction in CO₂ removal cost under different process conditions (solid circulation and make-up flow). The present study may be used as an assessment tool of new sorbents to understand what prices would be competitive compare with raw limestone in the CO₂ looping capture systems.     

Effect of rice husk ash addition on CO2 capture behavior of calcium-based sorbent during calcium looping cycle

Rice husk ash/CaO was proposed as a CO₂ sorbent which was prepared by rice husk ash and CaO hydration together. The CO₂ capture behavior of rice husk ash/CaO sorbent was investigated in a twin fixed bed reactor system, and its apparent morphology, pore structure characteristics and phase variation during cyclic carbonation/calcination reactions were examined by SEM-EDX, N₂ adsorption and XRD, respectively. The optimum preparation conditions for rice husk ash/CaO sorbent are hydration temperature of 75 °C, hydration time of 8 h, and mole ratio of SiO₂ in rice husk ash to CaO of 1.0. The cyclic carbonation performances of rice husk ash/CaO at these preparation conditions were compared with those of hydrated CaO and original CaO. The temperature at 660 °C–710 °C is beneficial to CO₂ absorption of rice husk ash/CaO, and it exhibits higher carbonation conversions than hydrated CaO and original CaO during multiple cycles at the same reaction conditions. Rice husk ash/CaO possesses better anti-sintering behavior than the other sorbents. Rice husk ash exhibits better effect on improving cyclic carbonation conversion of CaO than pure SiO₂ and diatomite. Rice husk ash/CaO maintains higher surface area and more abundant pores after calcination during the multiple cycles; however, the other sorbents show a sharp decay at the same reaction conditions. Ca₂SiO₄ found by XRD detection after calcination of rice husk ash/CaO is possibly a key factor in determining the cyclic CO₂ capture behavior of rice husk ash/CaO.     

A rate equation for Ca(OH)2 and CO2 reaction in a spouted bed reactor at low gas concentrations

In the present study, the carbonation reaction of hydrated lime in semi-dry condition is investigated experimentally in a laboratory-scale spouted bed reactor. Results show that for operating conditions where the concentration of CO₂ is low, the capture efficiency is raised by increasing the inlet CO₂ concentration. Additionally, because of the inconsistency between the experimental reaction rate and the calculated values based on the previous proposed equations, a new rate equation is introduced that considers the dependency of CO₂ concentration too. To validate the proposed equation, its predictions were compared with another set of experimental data.     

CO2 capture from flue gases using a fluidized bed reactor with limestone

The CO₂ capture from flue gases by a small fluidized bed reactor was experimentally investigated with limestone. The results showed that CO₂ in flue gases could be captured by limestone with high efficiency, but the CO₂ capture capacity of limestone decayed with the increasing of carbonation/calcination cycles. From a practical point of view, coal may be required to provide the heat for CaCO₃ calcination, resulting in some potential effect on the sorbent capacity of CO₂ capture. Experiment results indicated that the variation in the capacity of CO₂ capture by using a limestone/coal ash mixture with a cyclic number was qualitatively similar to the variation of the capacity of CO₂ capture using limestone only. Cyclic stability of limestone only undergoing the kinetically controlled stage in the carbonation process had negligible difference with that of the limestone undergoing both the kinetically controlled stage and the product layer diffusion controlled stage. Based on the experimental data, a model for the high-velocity fluidized bed carbonator that consists of a dense bed zone and a riser zone was developed. The model predicted that high CO₂ capture efficiencies (>80%) were achievable for a range of reasonable operating conditions by the high-velocity fluidized bed carbonator in a continuous carbonation and calcination system.     

Kinetic study on carbonation of crude Li<Subscript>2</Subscript>CO<Subscript>3</Subscript> with CO<Subscript>2</Subscript>-water solutions in a slurry bubble column reactor

Investigations were conducted to purify crude Li₂CO₃ via direct carbonation with CO₂-water solutions at atmospheric pressure. The experiments were carried out in a slurry bubble column reactor with 0.05 m inner diameter and 1.0 m height. Parameters that may affect the dissolution of Li₂CO₃ in the CO₂-water solutions such as CO₂-bubble perforation diameter, CO₂ partial pressure, CO₂ gas flow rate, Li₂CO₃ particle size, solid concentration in the slurry, reaction temperature, slurry height in the column and so on were investigated. It was found that the increases of CO₂ partial pressure, and CO₂ flow rate were favorable to the dissolution of Li₂CO₃, which had the opposite effects with Li₂CO₃ particle size, solid concentration, slurry height in the column and temperature. On the other hand, in order to get insight into the mechanism of the refining process, reaction kinetics was studied. The results showed that the kinetics of the carbonation process can be properly represented by 1−3(1−X)^2/3+2(1–X)=kt+b, and the rate-determining step of this process under the conditions studied was product layer diffusion. Finally, the apparent activation energy of the carbonation reaction was obtained by calculation. This study will provide theoretical basis for the reactor design and the optimization of the process operation.     

Analysis of dynamic CO2 capture over 13X zeolite monoliths in the presence of SOx,NOx and humidity

In this investigation, the CO₂ capture performances of zeolite 13X monoliths with 600 and 800 cells per square inch (cpsi) in the presence of SO₂/NO impurities under dry and humid conditions were evaluated and compared with that of 13X beads. Dynamic breakthrough tests demonstrated a drastic reduction in CO₂ capture capacity and deterioration of kinetics under dry-clean conditions, whereas, upon switching the feed from a clean gas to contaminated gas which contained SO₂ and NO, different adsorption performance was observed. Specifically, in dry-contaminated mode, the adsorbents retained their capture capacities with comparable kinetics to that of dry-clean feed conditions, however, in humid-contaminated mode, the adsorbents experienced improved CO₂ uptake and CO₂/N₂ selectivity, albeit at the expense of deteriorated kinetics. These findings indicate that the presence of SO₂ and NO contaminants, especially SO₂ contaminants, lead to dramatic changes in the adsorption performance of zeolite 13X monoliths, indicating the importance of evaluating adsorbent materials under realistic conditions.