Dielectric properties and microstructural behaviour of B-site calcium-doped barium titanate ceramics

Dielectric properties and microstructural behaviour of Ba_1–x Sr _x Ti_1–y Ca _y O_3–y ceramics, where strontium and calcium were doped on the barium and titanium sites, respectively, within the range 0x0.24 and 0y0.05, were investigated. Calcium addition decreased the tetragonality,c/a, increased the unit cell volume, and lowered the Curie temperature, which were all attributed to the occupancy of Ca²⁺ ions on titanium sites. When sintered at a low oxygen partial pressure of 10^–9 MPa, a resistivity higher than 10¹¹ cm was maintained for the formulations containing B-site calcium substitution more than 0.5 mol %. With increasing the amount of calcium addition, the Curie peak was depressed and completely broadened for the compositions with calcium addition more than 3 mol %, where the average grain size was smaller than 1 m. Co-firing with nickel electrodes in a reducing atmosphere also depressed the Curie peak and inhibited the grain growth due to the diffusion of nickel into the dielectrics.     

X-Ray Diffraction Studies on LaBa2Cu3Ox Cuprates with Iron Substitution

LaBa₂Cu_3–y Fe _y O _x ceramic samples with y = 0.00–1.50 are synthesized by the solid-state reaction technique. Rietveld analysis for X-ray diffraction is performed on these iron-doped samples. A BaCuO₂ impurity phase and a ceramic cuprate phase coexist in each sample. An orthorhombic-to-tetragonal (OT) phase transition occurs in the doping range of 0.03y0.06, and a tetragonal-to-orthorhombic (TO) one occurs in the doping level of 0.10y0.25. There is a jump in the structural parameters due to the iron doping. The occupancy of oxygen at the O(4) site, which is in the La plane at z = 1/2, increases with increase in iron content. These results may relate to the iron preferential occupancy for the Cu(1) site at the lower doping level, and for Cu(2) sites at the higher doping level.     

Y xBayCuzO7− δ solid solutions

Y_xBa_yCu_zO_7– ceramics forming at isobaric conditions were studied by x-ray diffraction analysis, dynamic magnetic measurements and potentiometric titration. It was established that compositions: 0.8 x 1.2 y=2, z=3; x-1, 1.8 y 2.2, z=3; x=1, y=2, 2.7 z 3.4: are in the homogeneity range of 123. It was found that compositions with nonstoichiometric cations rations have minimum T_c.     

Phase equilibria in PbTe/CdTe alloys

The Pb/Cd/Te phase diagram in the range Pb_1–x Cd _x Te_1+y where 0x0.15 and y±0.05 was examined by differential thermal analysis. The congruent melting point for PbTe was found to be unique. Annealing of alloys in Te-rich and deficient atmospheres showed that the phase width of the system increased and moved more towards the n-side with increasing cadmium content. The energy of formation of a divacancy for a 3 mole % CdTe alloy was found to be 0.16 eV less than that in PbTe.     

Isochoric pvT measurements of SF6 in the density range 100 to 1200 kg · m−3

The pvT properties of SF₆ were determined by an isochoric method. The pressure p and the temperature T were measured in the pressure range 1.5 MPa p 9.0 MPa and in the temperature range 293 K T 340 K. The results are compared with data in the literature. The adsorption of SF₆ on glass and iron surfaces and its influence on the pvT measurements are also briefly discussed.Paper presented at the Tenth Symposium on Thermophysical Properties, June 20–23, 1988, Gaithersburg, Maryland, U.S.A.     

Chemical Control of Underdoped and Overdoped States in Y(Ba2 ? ySry)Cu3O6 + δ

The chemical control of underdoped and overdoped states in the Y(Ba_{2 – y} Sr _y )Cu₃O_{6 +} (0.1 and 0.9) compounds has been observed by high-resolution O K-edge X-ray-absorption near-edge-structure spectra. The chemical substitution of Sr for Ba in the fully-oxygenated Y(Ba_2–y Sr _y )Cu₃O_{6 +} (0.9) compounds gives rise to high hole concentrations within both the CuO₂ planes and the out-of-plane sites, leading to the overdoped state and the decrease in the superconducting transition temperature from 92 K for y=0 to 84 K for y=0.8. In contrast, an increase in the Sr content in the oxygen-deficient Y(Ba_{2 – y} Sr _y )Cu₃O_{6 +} (0.1) compounds did not indicate superconductivity. The oxygen-deficient compounds exhibit the underdoped state due to the low hole concentration.     

Superconducting properties of the lithium-substituted YBa2Cu4O8 prepared by the sol-gel method

The effects of the lithium substitution for copper on the properties of the superconducting YBa₂Cu₄O₈ were studied. Single-phase YBa₂Cu_4–x LixO₈ was successfully prepared by the sol-gel method under ambient pressure over a composition range of 0x 0.08, while impurity phases appeared at x=0.10 and 0.20. The lattice constants of YBa₂Cu_4–x Li _x O₈ were almost invariant with increasing lithium content x. The superconducting transition temperature decreased monotonically with increasing x in the range, 0x0.08. The suppression of superconductivity was discussed in terms of the impurity effect in the CuO₂ planes.     

Mean polarizabilities and second optical and density virial coefficients of CH3OH and CCl2F2 between 300 and 355 K

Mean dipole polarizabilities ₀(, T) as well as second optical (or refractive index) virial coefficients b _R(, T) and second density virial coefficients B(T) of gaseous CH₃OH and CCl₂F₂ have been determined by precise measurements of the refractive index n(, T, p) [543 nm 633 nm, 300 K T 355 K, p<0.25 bar (CH₃OH) and p<3 bar (CCl₂F₂)]. ₀ critically compared with the few data in literature. The b _R of these gases was measured for the first time with the cyclic-expansion method. The values of ¦B¦ and b _R=3160(25) cm³ · mol^–1 measured for CH₃OH are considerably greater than the values calculated by Buckingham's statistical-mechanical expressions for a Stockmayer interaction potential. This difference is discussed by assuming dimerization via H bonds, with result H ₂ ⁰ –(28 ... 33) kJ · mol^–1 and S ₂ ⁰ –(116 133) J · mol^–1 · K^–1 for the dimerization enthalpy and entropy for standard conditions, respectively. On the other hand, Buckingham's formulae can be used with success to estimate b _R and B of CCl₂F₂.Dedicated to Prof. Dr. F. Kohler on the occasion of his 65th birthday     

Energy Scales in the High-Tc Superconductor YBa2Cu3O6+x

The optical conductivity sum rule is used to examine the evolution of the spectral weight N() in both the normal and superconducting states of optimally and underdoped YBa₂Cu₃O_6+x along the a axis. Differences in N() above and below T _c allow the strength of the superconducting condensate _s to be determined. In the optimally-doped material, _s is fully formed at energies comparable to the full superconducting gap maximum (0.1 eV), while in the underdoped material the energy scale for convergence is considerably higher (0.6 eV). This difference is discussed in terms of normal-state properties.     

The preparation of high transition temperature superconducting Pb-Bi-Ge alloy filaments using the method of glass-coated melt spinning

The melt spinning of Pb-Bi-Ge alloys with Pyrex glass was investigated as a means of producing a superconducting long filament with highT _c. Continuous filaments with maximumT _c of more than 10 K of Pb_100-x-y Bi _x Ge _y (15x37 and 725) were obtained from the molten state at 1500 K with a winding speed of 0.95 m sec^–1. The Pb₄₉Bi₃₃Ge₁₈ filament, which was 34×10^–6 m diameter and a ductile material with a tensile strength of 20 MPa and elongation of 2.7%, exhibited superconductivity at the highestT _c of 14.3 K. These filaments were found to be polycrystalline with a grain size of more than 5000×10^–10 m and had a mixed structure of germanium (diamond) (h c p) and bismuth phases. The germanium element distributed homogeneously in the filament.     

Some properties of Sb2Te3−xSex for nonvolatile memory based on phase transition

Composition dependence of properties of Sb₂Te_3–x Se _x in the range 0x<3 were studied using differential thermal analysis and X-ray diffraction. Sb₂Te_3–x Se _x form solid solution for 0<x1.25 and 2.75x<3. A systematic study of crystallization temperature in Sb₂Te_3–x Se _x (0x2.75) thin films prepared by flash evaporation was carried out. In preliminary experiments for some compositions, more than 10³ repetitions between amorphous and crystalline states were attained by the application of electric pulses.     

Hc2 of MgCNi3 Determined from the Specific Heat and Resistivity Measurements

H _c2 of MgCNi₃ has been determined from the specific heat C and resistivity measurements in the same sample. The results from are nearly identical with those determined from the anomaly in C. Furthermore, utilizing the relation (H) H and the value of d/dH, the obtained value of H _c2 is the same as that by the WHH model, if the spin paramagnetic effect and the spin–orbit interaction are taken into account. The results of this comparison have strong implications on the order parameter of MgCNi₃.     

Mean polarizabilities and second and third virial coefficients of the gases C2H4, C2H6, and SF6

Mean polarizabilities ₀(₀, T) as well as second and third virial coefficients B(T) and C(T) of the equation of state of the gases C₂H₄, C₂H₆, and SF₆ have been determined from refractive index measurements with a Michelson interferometer for wavelength ₀=632.99 nm in the overall ranges 250 KT 340 K and 0p3 MPa of temperature T and pressure p. Some negative C(T) values at low temperatures have been obtained. The C(T) data could be fitted satisfactorily to the simple three-parameter function C(T)= a(T–T ₀) exp[ –b(T–T ₀)], with the maximum near the critical temperature T _c. A possible correlation between C(T) and the vapor pressure p _v(T) is discussed.     

The Specific Heat and the Fermi Surface Anisotropy in Sr2RuO4

The influence of the Fermi surface anisotropy on the specific heat jump is studied for the p-wave superconductor with a gap function d = z^(k _x ± ik _y ) in connection with Sr₂RuO₄. It is shown that the normalized specific heat jump, C/T _c , is reduced from its universal value, 1.43, in accordance with experimental findings. We show that this behavior fits well into our present understanding of the quasiparticle spectrum and the impurity effects.     

Electrical properties and phase transition of Ge1−x Sn x Se2.5 thin films

The Ge_1–x Sn _x Se_2.5 system was prepared by melting the correct ratio of high purity elements in quartz evacuated ampoules followed by quenching in ice. It was found that, within the Ge_1–x Sn _x Se_2.5 system, a glassy state can be formed when 0 x 0.4. On increasing x to 0.6 a glassy state could not be obtained, as is confirmed by X-ray diffraction. Differential thermal analysis (DTA) was carried out to study the effect of composition on the stability of amorphous phase. Ge_1–x Sn _x Se_2.5 (where 0 x 0.6) thin films have been prepared by the thermal evaporation technique. The electrical conductivity of the thin films have been studied as a function of composition and film thickness.     

Crystallization kinetics of Zr-rich FexZr0−x0−x0−x(20 ⩽ x ⩽ 40) metallic glasses

The crystallization kinetics of the melt-spun Fe-Zr metallic glasses in the iron-rich region has been investigated by means of DSC and X-ray diffraction. The crystallization mode changes with iron concentration. In the lower iron region, 20 x 25, the Fe _x Zr100–x glasses crystallize into -Zr and Ti₂Ni-type FeZr₂ with an accompanying sharp and large exotherm at the first crystallization step and immediately after this step, they transform into orthorhombic FeZr₃. On the other hand, the alloys with 35 x 40 exhibit a gradual exotherm which initiates from a temperature far below the definite crystallization temperature (T _x). The Fe-Zr metallic glasses in this concentration region crystallize polymorphously into the oxygenstabilized Ti₂Ni-type FeZr₂ with accompanying relatively small and composite exotherms. The annealing at a temperature where the gradual exotherm occurs for the alloys with 30 x 40 does not cause any changes of X-ray halo pattern but results in the reduction of the heat of exotherm due to the crystallization.     

X-ray,electrical conductivity and magnetic hysteresis studies of the chalcogenide system Zn1−xCuxCr2Se4

X-ray diffraction studies performed here indicated solid-solution formation between ZnCr₂Se₄ and CuCr₂Se₄, and all the compounds could be indexed on the basis of cubic spinel lattice. The compositions between 0 x 0.8 showed semi-conducting behaviour, while CuCr₂Se₄ (x=1.0) exhibited metallic conductivity. Seebeck measurements showd P-type behaviour for 0 x 1. Magnetic hysteresis indicated a ferromagnetic nature for all the compounds except ZnCr₂Se₄ (x=0). The shapes of/ _i plotted againstT exhibited single domain behaviour, and Curie temperatures showed an increase with increasing copper concentration.     

Thermal conductivity of liquid n-alkanes

The thermal conductivity of liquids has been shown in the past to be difficult to predict with a reasonable accuracy, due to the lack of accurate experimental data and reliable prediction schemes. However, data of a high accuracy, and covering wide density ranges, obtained recently in laboratories in Boulder, Lisbon, and London with the transient hot-wire technique, can be used to revise an existing correlation scheme and to develop a new universal predictive technique for the thermal conductivity of liquid normal alkanes. The proposed correlation scheme is constructed on a theoretically based treatment of the van der Waals model of a liquid, which permits the prediction of the density dependence and the thermal conductivity of liquid n-alkanes, methane to tridecane, for temperatures between 110 and 370 K and pressures up to 0.6 MPa, i.e., for 0.3T/T _c0.7 and 2.4P/P _c3.7, with an accuracy of ±1%, given a known value of the thermal conductivity of the fluid at the desired temperature. A generalization of the hard-core volumes obtained, as a function of the number of carbon atoms, showed that it was possible to predict the thermal conductivity of pentane to tetradecane±2%, without the necessity of available experimental measurements.     

Magnetic field dependence of the density of states of YBa2Cu3O6.95: Implications for the vortex structure

The total specific heat of YBa₂Cu₃O_6.95 single crystals includes contributions from phonons and spin-1/2 particles, as well as electronic contributions. The electronic specific heat is described by a quadratic term T² in zero field and a linear term [(0)+(H)]T which is increased when a magnetic field H is applied perpendicular to the CuO₂ planes. In agreement with d-wave superconductivity, we find that _n/T_c and (H)_n(H/H_c2)^1/2, where _n is the coefficient of the normal-state linear term. The H^1/2 dependence of the density of states at the Fermi level was predicted by G. Volovik for lines of nodes in the gap: the quasiparticles which contribute to this density of states are close to the nodes in momentum space and are located outside the vortex core.     

Low temperature heat release,sound velocity and attenuation,specific heat and thermal conductivity in polymers

We have measured the long time (t = 5 to 200 h) heat release of Polymethylmethacrylate (PMMA) and Polystyrene (PS) at 70 mK T 300 mK. After cooling from a charging temperature of 80 K the heat release in PMMA shows a t^–1 dependence in the measured time and temperature ranges in agreement with the tunneling model. In contrast, for PS we observe strong deviations from at ^–1 dependence and a factor of ten smaller heat release than in PMMA in apparent contradiction to specific heat and thermal conductivity data for PS. To compare the heat release with other low temperature properties and to verify the consistency of the tunneling model we have measured also the acoustical properties (sound velocity and attentuation), the specific heat and the thermal conductivity of PMMA and PS in the temperature range 70mKT 100 mK, 70mKT200 mK and 0.3 KT4K, respectively. We show that the anomalous time dependence of the heat release of PS is due to the thermally activated relaxation of energy states with excitation energies above 15 K.