A Case Study on Optimization of Biomass Flow During Single-Screw Extrusion Cooking Using Genetic Algorithm (GA) and Response Surface Method (RSM)

In the present study, response surface method (RSM) and genetic algorithm (GA) were used to study the effects of process variables like screw speed, rpm (x ₁), L/D ratio (x ₂), barrel temperature (°C; x ₃), and feed mix moisture content (%; x ₄), on flow rate of biomass during single-screw extrusion cooking. A second-order regression equation was developed for flow rate in terms of the process variables. The significance of the process variables based on Pareto chart indicated that screw speed and feed mix moisture content had the most influence followed by L/D ratio and barrel temperature on the flow rate. RSM analysis indicated that a screw speed?>?80 rpm, L/D ratio?>?12, barrel temperature?>?80 °C, and feed mix moisture content?>?20% resulted in maximum flow rate. Increase in screw speed and L/D ratio increased the drag flow and also the path of traverse of the feed mix inside the extruder resulting in more shear. The presence of lipids of about 35% in the biomass feed mix might have induced a lubrication effect and has significantly influenced the flow rate. The second-order regression equations were further used as the objective function for optimization using genetic algorithm. A population of 100 and iterations of 100 have successfully led to convergence the optimum. The maximum and minimum flow rates obtained using GA were 13.19?×?10^?7 m³/s (x ₁?=?139.08 rpm, x ₂?=?15.90, x ₃?=?99.56 °C, and x ₄?=?59.72%) and 0.53?×?10^?7 m³/s (x ₁?=?59.65 rpm, x ₂?=?11.93, x ₃?=?68.98 °C, and x ₄?=?20.04%).     

Use of a Core-Shell Column for the Development of a Green LC Method for Thiol Determination in Fresh Fruits Following Derivatization with Methyl Propiolate

A novel HPLC method has been established for the determination of thiols in fruit samples, introducing, for the first time, methyl propiolate as an advantageous precolumn derivatization reagent for cysteine (CYS), glutathione (GSH), and N-acetylcysteine (NAC). The formed derivatives were detected at 285 nm, following isocratic separation on a core-shell column (Ascentis Express C18, 50?×?2.1 mm i.d., 2.7 μm) with a mobile phase of 15 mmol L^?1 (ΝΗ₄)₂ΗPO₄/H₃PO₄ (pH?=?2.2)/methanol (92:8?v/v), containing 1 mmol L^?1 EDTA, at a flow rate of 0.2 mL min^?1. Derivatization parameters were optimized including pH and concentration of buffering medium, amount concentration of methyl propiolate, derivatization time, and temperature, by the univariate approach. Under optimal conditions, the developed analytical scheme offers a total analysis time of less than 10 min, limits of detection in the range 0.1–0.5 μmol L^?1, and satisfactory linearity up to 100 μmol L^?1 for all analytes. The method proved also to be equally selective and robust. Endogenous thiols were determined in melon, watermelon, and avocado, using the standards addition approach, after minimal sample preparation, with no use of organic solvents. The accuracy was evaluated by recovery experiments resulting in the range of 86.4–118.5 %.     

Smart NMR Method of Measurement of Moisture Content of Vegetables During Microwave Vacuum Drying

Microwave drying is usually combined with vacuum environment in conjunction with hot air flow to draw the moisture rapidly. The moisture content of the vegetables undergoing drying is hard to measure online. This research designed a microwave vacuum drying (MVD)-low-field nuclear magnetic resonance (NMR) smart device and investigated the feasibility of NMR method for online measurement of state of moisture during MVD. The relation between the signal amplitude (A ₂) and the true moisture content (M ₁) of six kinds of vegetables (mushroom, carrot, potato, lotus, edamame, vegetable corn) was fitted to estimate if NMR can measure the M ₁ of vegetables directly. Results showed that A ₂ and M ₁ of different fresh vegetables had no single empirical mathematical model to fit. However, for each kind of these vegetables, the A ₂ and corresponding M ₁ in different MVD stages showed a significant linear relationship. The predicted moisture content (M ₂) of mushroom: M ₂ = 5.25351 × 10^?4 A ₂ ? 0.34042, R = 0.996; carrot: M ₂ = 5.78756 × 10^?4 A ₂ ? 0.14108, R = 0.998; potato: M ₂ = 3.10019 × 10^?4 A ₂ ? 0.10612, R = 0.991; lotus: M ₂ = 2.32415 × 10^?4 A ₂ ? 0.01573, R = 0.998; edamame: M ₂ = 3.13310 × 10^?4 A ₂ ? 0.4198, R = 0.996; vegetable corn: M ₂ = 1.69461 × 10^?4 A ₂ ? 0.09063, R = 0.995. The linear models between M ₂ and A ₂ were able to estimate the end point (M ₁ < 8%) of MVD with a high accuracy (P > 0.950).     

Automated Sequential Injection Method for Determination of Caffeine in Coffee Drinks

An automated sequential injection analysis spectrophotometric assay for the determination of purine alkaloids in coffee drinks was developed. The sample was treated with a carrez reagent for matrix suppression followed by filtration; subsequently, alkaloids were separated from organic acids using a short C18 monolithic column (10 × 4.6 mm). The flow rate of the separation step was 10 μL s^?1 with 10% v/v of methanol as the mobile phase. The sum of alkaloids evaluated as caffeine was detected at 274 nm. The influence of the main parameters affecting the quantification of purine alkaloids was optimized. One sample analysis lasted 15 min when aspirated in triplicate. The linear range was 1–15 mg L^?1, and the determination coefficient (r ²) was 0.9969. The limit of detection and limit of quantitation were 0.128 and 0.425 mg L^?1, respectively. The repeatability evaluated as the relative standard deviation (RSD) was 3.58% (n = 12, 10 mg L^?1). Under optimal conditions, the method was successfully applied to determine purine alkaloids in different real samples including soluble coffee, coffee from an espresso machine, and brewed coffee drinks.     

A mathematical model for moisture movement during continous and intermittent drying of <Emphasis Type="Italic">Eucalyptus saligna</Emphasis>

A modified diffusion-based mathematical model is proposed to describe the moisture movement during continuous and intermittent drying of Eucalyptus saligna. This model includes the temperature change, the surface drying coefficient (β _n ) and 2 diffusion coefficients [from green to FSP (D _f ) and from FSP to dry condition (D _o )] as important parameters. The final model expression obtained was M?=?exp (??25 β _n ² D _t /l²) with the β _n used was 1.5807 kg m^?2 s^?1, the D _f was 2.26?×?10^?11 m² s^?1, and the D _o was 5.85?×?10^?12 m² s^?1. The range of temperature change between heating and non-heating phases in the intermittent drying regimes was from 24.9 to 31.8 °C. The R² values obtained when the model was fitted into the drying data of different intermittent regimes ranged from 71.5 to 85.9%. The R² value was 87.4% when the model was fitted into continuous trial data. The high values of R² indicate that the model can be used to understand the moisture reduction both in intermittent and continuous regimes.     

Thermal transition and thermo-physical properties of potato (<Emphasis Type="Italic">Solanum tuberosum L</Emphasis>.) var. Russet brown

Potatoes are an important food in many regions of the world and are commonly used in a variety of food products. Thermal transition and thermo-physical properties of potatoes are important in order to design efficient food processes and select appropriate storage conditions. In this study, we determined the thermal transitions and thermophysical properties of raw and blanched/par-fried potato for a temperature range of ??32 to 21.1 °C. Using differential scanning calorimetry, we found an initial freezing point (T_f) at ??1.8?±?0.1 °C, an onset of melting (T_m^′) at ??9.9?±?0.2 °C and an unfreezable water content (X^′_w) for maximally freeze-concentrated raw potato at 0.21 kg water/kg potato. Corresponding values for blanched/par-fried potatoes were ??0.9?±?0.1 °C, ??11.0?±?0.2 °C and 0.18 kg water/kg potato. Results show that an increase in solids content decreased T_f of both raw and blanched potatoes. We modelled the relationship between them using the Chen model. The apparent specific heat (C_app) increased around T_f to 31.7?±?1.13 kJ/kg K for raw potato and 26.7?±?0.62 kJ/kg K for blanched/par-fried potato. For frozen raw potato at ??32 °C, thermal diffusivity (α) was 0.89?±?0.01?×?10?^?6 m²/s and thermal conductivity (k), 1.82?±?0.14 W/m K, respectively. These values were higher for frozen raw potato than for the unfrozen raw potato (0.15?±?0.01?×?10?^?6 m²/s and 0.56?±?0.08 W/m K, respectively at 21.1 °C). The apparent density (ρ) of frozen raw potato (992?±?4.00 kg/m³ at ??32 °C) was less than that for unfrozen raw potato (1053?±?4.00 kg/m³ at 21.1 °C), and a similar trend was obtained for blanched/par-fried potato (993?±?2.00 kg/m³ at ??32 °C and 1188?±?7.00 kg/m³ at 21.1 °C, respectively). This study established a correlation between thermo-physical properties and temperature. Findings may be used to inform the design and optimization of freezing processes and frozen storage for potato products.     

Application of Bismuth(III)-Entrapped XO Biosensing System for Xanthine Determination in Beverages

A xanthine biosensor was prepared by electrochemical immobilization of xanthine oxidize enzyme onto carbon paste electrode via entrapment of Bi³⁺. After the optimization of experimental parameters, analytical characteristics were investigated. Two linear ranges between 0.02 and 0.06 and 1–7.5 μM with the equation y?=?93.00x?+?0.12 and y?=?1.07x?+?18.03 with the correlation coefficients of R ²?=?0.9951 and R ²?=?0.9931, respectively, were obtained for this biosensing system. RSD value was calculated for 0.04 μM xanthine (n?=?5) and found as 3.84%. LOD and LOQ values were also calculated and revealed as 1.30?×?10^?8 and 4.3?×?10^?8 M, respectively. Then, this biosensor was applied for xanthine detection in real samples. As a sample treatment, only necessary dilutions were made. Four types of beverages including wine, energy drink, peach, and sour cherry juice were used for this purpose. Obtained recovery values demonstrate that this system is applicable for xanthine detection in real samples without needing any laborious sample pretreatment procedures.     

A Cassava Starch–Chitosan Edible Coating Enriched with <Emphasis Type="Italic">Lippia sidoides</Emphasis> Cham. Essential Oil and Pomegranate Peel Extract for Preservation of Italian Tomatoes (<Emphasis Type="Italic">Lycopersicon esculentum</Emphasis> Mill.) Stored at Room Temperature

The effect of edible cassava starch–chitosan coatings incorporated with rosemary pepper (Lippia sidoides Cham.) essential oil and pomegranate peel extract on the shelf-life of tomatoes during storage at 25 °C for 12 days was investigated. Sixteen formulations, containing 10 g L^?1 cassava starch and various concentrations of chitosan (5, 10, 20, 30 g L^?1), essential oil (0, 2.5, 5, 10 mL L^?1) and pomegranate peel extract (0, 5, 10, 20 mL L^?1) were prepared and applied to tomatoes. Physical–chemical and microbiological analyses were performed on days 1, 4, 8 and 12. Most of the coatings delayed the ripening of tomatoes, lowering the total soluble solids (38?44 g sucrose kg^?1) and weight loss (93?128 g kg^?1) and maintaining constant firmness compared to the uncoated tomatoes (45 g sucrose kg^?1, 175 g kg^?1) at 12 days of storage. Conversely, except red intensity (a*), which was higher for the uncoated samples, the colour parameters (L*, b*) of the coated and control tomatoes were similar at the end of storage. Uncoated and coated tomatoes showed no contamination during storage. The coatings showed potential to maintain the quality of tomatoes during storage at 25 °C for 12 days. In this context, tomatoes coated with the formulation comprising 10 g L^?1 cassava starch, 10 g L^?1 chitosan, 10 mL L^?1 essential oil and 20 mL L^?1 pomegranate peel extract showed the lowest weight loss and reduced total soluble solids content compared with uncoated ones.     

Quantification and Discrimination of Viable and Dead <Emphasis Type="Italic">Escherichia coli</Emphasis> O157:H7 Cells from Chicken Without Enrichment by Ethidium Bromide Monoazide Real-time Loop-Mediated Isothermal Amplification

In this study, a rapid and sensitive method of real-time loop-mediated isothermal amplification (Rti-LAMP) assays was developed for quantification and discrimination of viable and heat-killed E. coli O157:H7 cells treated with low concentration of ethidium bromide monoazide (EMA). Four micrograms per milliliter of EMA was chosen as the optimal concentration which did not inhibit DNA amplification derived from viable cells, but significantly increased the Tt values of dead cells in Rti-LAMP assays. When the DNA from 2.0?×?10³ viable CFU of E. coli O157:H7 was subjected to EMA-Rti-LAMP, the resulting Tt value was 17.73 min. In contrast, the DNA from 2.0?×?10³?CFU completely heat destroyed CFU of E. coli O157:H7 did not yield a positive amplification which Tt value was regarded as 60 min. When the DNA from viable plus heat-killed CFU at a ratio of 5:2995 was subjected to EMA-Rti-LAMP, the resulting Tt value was 23.06 min, which was statistically identical (P?<?0.05) to the Tt value of 24.07 min obtained with the DNA from only 5 viable CFU. The results indicate that even though 3.0?×?10³ dead cells yielded a negative amplification setting the Tt value as 60 min, low numbers of viable cells in the presence of much higher numbers of dead cells still yielded a linear plot for enumerating viable CFU from Tt values. Detection of E. coli O157:H7 derived from contaminated chicken samples, the EMA-Rti-LAMP could notably distinguish viable and heat-killed cells from 5.0?×?10¹ to 1.0?×?10⁴?CFU/g without enrichment.     

Steady- and Unsteady-State Determination of the Water Vapor Permeance (<Emphasis Type="Italic">WVP</Emphasis>) of Polyethylene Film to Estimate the Moisture Gain of Packed Dry Mango

The water vapor permeance (WVP; g m^?2 d^?1 Pa^?1) of packaging films quantifying the water vapor transfer rate between foods and its surroundings is usually determined in units operating under steady-state conditions that do not necessarily reflect food handling scenarios. This study evaluated the determination of the WVP of a polyethylene (PE) film by steady-state method ASTM F1249-06 using a permeability cell and unsteady-state method ASTM E96/E96M in which 102 vacuum-sealed PE bags containing silica gel were stored (37.8 °C, 75% relative humidity) and weighed over 25 days. Average steady-state WVP (2.935 ± 0.365 × 10^?3, n = 4) fell within the 95% quantiles of unsteady-state WVP values (1.818–3.183 × 10^?3, n = 2142). Moisture uptake of dehydrated mango stored at 37.8 °C and 75% relative humidity was predicted with WVP values obtained by both methods. Predictions were validated by monitoring over 25 days the weight gain of 100 PE bags with dry mango. Experimental moisture averages during storage fell within one standard deviation of predictions using the unsteady-state WVP (R ² = 0.974). The same was observed only until day 15 for predictions obtained with the steady-state WVP. Calculations for days 20–25 overestimated the moisture uptake by 6.0–7.2%, resulting in registered R ² = 0.924. The unsteady-state WVP determination is low-cost, uses large numbers of film samples, and allowed more accurate predictions of dry mango moisture uptake. Knowledge of the moisture uptake controlled by the film WVP is essential when predicting the safety and quality changes limiting the shelf-life of foods.     

Effect of Tannin Extracts on Biofilms and Attachment of <Emphasis Type="Italic">Escherichia coli</Emphasis> on Lettuce Leaves

Lettuce is often involved in foodborne outbreaks caused by pathogenic Escherichia coli. Current control strategies have often proved ineffective to ensure safe food production. For that reason, the present study compared the efficacy of tannin extracts and chlorine treatments on the reduction of E. coli ATCC 25922 adhered to lettuce leaves. E. coli was inoculated artificially on leaf surfaces of fresh crisp lettuce. Effectiveness of water, chlorine (200 mg/L), and three commercial available tannin extracts from Acacia mearnsii De Wild. (tannin AQ (2 %, w/v), tannin SG (1 %, v/v) and tannin SM (1 %, v/v)) treatments was evaluated using the viable plate count method and scanning electron microscopy (SEM). SEM results revealed that bacterial cells are attached as individual cells and in clusters to the leaf surface after 2 h of incubation. Biofilm formation was observed after 24 h of incubation. The tannin SM treatment was able to reduce counts in approximately 2 log CFU/cm² on leaf segments. However, treatment was less effective in the reduction of E. coli counts after 24 h of incubation when compared to 2 h incubation of the same extract. The results suggest that the tannin SM extract diminishes E. coli counts adhered to and under biofilm formation on lettuce leaves and its effect is similar to the use of chlorine solutions.     

Conventional and Microwave-Assisted Extraction of Mucilage from <Emphasis Type="Italic">Opuntia ficus-indica</Emphasis> Cladodes: Physico-Chemical and Rheological Properties

Cactus pear cladodes processing has potential value for mainstream industries and is equally important for marginal rural communities in arid regions. This work is focused on physico-chemical and rheological properties of Opuntia ficus-indica (OFI) peeled cladodes extracted by conventional method “CE” and using microwave-assisted extraction “MAE.” MAE gave the highest yield extraction (8.13 %, w/w) within the lowest extraction time (500 W/7 min) and provided more protein (×1.03) and carbohydrates (×1.51) than CE. The monosaccharides detected by gas chromatography were arabinose, galactose, rhamnose, xylose, and galacturonic acid. The dialyzed mucilage solution characterized by SEC/MALS/VD/DRI (size-exclusion chromatography coupled with online multi-angle light scattering, viscometer detectors, and differential refractive index) revealed fractions with molecular weight (M _w ) ranging from 15.3–15.7?×?10⁶ g mol^?1 for the CE extracts and about 16.7–17.5?×?10⁶ g mol^?1 for the MAE extracts. Dynamic oscillatory testing has been used to study the rheological properties of mucilage solution within the concentration of 0.50–3.00 % (w/v) at 25 °C. The rheological profiles of CE and MAE showed similar behavior. At low frequency and low mucilage concentration (<2.00 %), the viscous component (G") predominated over the elastic component (G'), while for higher frequencies, the behavior is reversed (G'?>?G"). If safely controlled, alternative energies like microwaves could extract soluble polymers with comparable properties to commercial ones, conventionally extracted.     

Characterization of Biodegradable Films Based on <Emphasis Type="Italic">Salvia hispanica</Emphasis> L. Protein and Mucilage

Biodegradable films of chia by-products (mucilage and protein-rich fraction (PF)) incorporated with clove essential oil (CEO) were obtained and characterized. The effects of polymer concentration (PC; 1.0–3.0 %, w/v) and CEO concentration (0.1–1.0 %, v/v) were evaluated as well as the pH (7–10), using a 2³ factorial design with four central points. The films exhibited moisture values between 11.6 and 52.1 % (d.b.), which decreased (p?<?0.05) with increasing PC and CEO. The thickness of the films increased (p?<?0.05) with increasing PC. PC and pH influenced (p?<?0.05) the lightness (L) and variation in color between red and green (a). The orientation of the color to yellow-blue hues (b) decreased significantly (p?<?0.05) with increasing PC. Transparency was significantly lower and higher (p?<?0.05) than PC and CEO, respectively. The film surface morphology was evaluated using atomic force miscrocope images, and thermogravimetric analysis (TGA) was performed to study the thermal stability of the films. The displacement and tensile strength were significantly lower (p?<?0.05) at higher concentrations of CEO, this variable being the only one with a significant effect. The chemical composition of the films was confirmed utilizing Fourier transform infrared (FTIR) spectroscopy. The proportion of CEO added to the films had a significant influence on antimicrobial activity, inhibiting the growth of both Escherichia coli and Staphylococcus aureus.     

Comparative Study on the Inactivation and Photoreactivation Response of <Emphasis Type="Italic">Listeria monocytogenes</Emphasis> Seafood Isolates and a <Emphasis Type="Italic">Listeria innocua</Emphasis> Surrogate after Pulsed Light Treatment

The inactivation and photoreactivation response of six seafood-isolated Listeria monocytogenes and one Listeria innocua strain after pulsed light (PL) treatment was evaluated. The lower inactivation levels found after exposure of treated samples to daylight during the first 90 min of storage confirmed that both L. innocua and L. monocytogenes have the capability to photorepair PL-induced DNA damage upon appropriate conditions. Photoreactivation levels from 0.2 to 2.1 log CFU cm^?2 were observed depending on treatment intensity (fluence) and Listeria strain. Complete photorepair of PL-caused damage was not found even after treatments inducing low inactivation levels. Photoreactivation increased up to 2.1 log with the applied fluence up to a threshold able to cause between 2.4 and 5.4 log reductions under dark storage. Photorepair was not avoided but lower photoreactivation was observed after higher fluence inducing more than 6 log reductions under dark storage. Both L. innocua and L. monocytogenes serotype 1/2b exhibited the highest photoreactivation levels whereas serotypes 1/2a showed the lowest ones. The overall inactivation and photoreactivation responses of tested Listeria strains were comparable indicating that L. innocua may be a good surrogate for the safe evaluation, optimization and validation of PL technology to control L. monocytogenes in food products and food processing facilities.     

A Rapid and Visual Single Primer Isothermal Amplification-Based Method for the Detection of <Emphasis Type="Italic">Staphylococcus aureus</Emphasis> in Raw Pork Products

Staphylococcus aureus (S. aureus) is an important food-borne pathogen which poses a severe threat to public health worldwide. Rapid detection of S. aureus with high sensitivity is of particular importance for food safety. In this study, a novel single primer isothermal amplification (SPIA) method was established to detect S. aureus in food, targeting the accessory gene regulator (agr) gene with a DNA/RNA primer. The developed SPIA method has the advantages of visualization and avoiding tedious electrophoresis. In order to confirm the specificity of this method, 7 S. aureus strains and 26 non-S. aureus strains were detected with their pure cultures. The sensitivity and detection limit of S. aureus with artificially inoculated raw pork products by SPIA were evaluated through fluorescence and turbidity by naked eye and the amplification curve, which were 4.3?×?10⁰ CFU/mL and 5.6?×?10⁰ CFU/g, respectively. Compared with the conventional PCR method, the SPIA has 100-fold higher sensitivity and 100-fold lower detection limit. Therefore, the developed SPIA method is a potentially reliable tool for rapid and visual detection of S. aureus in food.     

Validation of a HS-SPME-GC Method for Determining Higher Fatty Esters and Oak Lactones in White Rums

Higher fatty esters and oak lactones are the main components of white rum aroma and furthermore, they have an important sensorial impact in these distilled alcoholic beverages. A method for analyzing these volatile compounds was validated. It involves a separation and concentration step using headspace solid-phase microextraction (HS-SPME) and determination by capillary gas chromatography using flame ionization detection. The method showed a good within-day (RSD?<?3 %) and between-day precision (RSD?<?5 %). The calibration curves were linear at the tested ranges (R?>?0.99) and the limits of detection and quantification were 0.001–0.018 and 0.003–0.054 mg L^?1 (12 %?v/v alcohol), respectively. Good recoveries were obtained (98.6–100.3 %). The method is suitable for the quality control of higher fatty esters and oak lactones in white rums.     

Speciation Determination of Selenium in Seafood by High-Performance Ion-Exchange Chromatography-Hydride Generation-Atomic Fluorescence Spectrometry

A high-performance ion-exchange chromatography coupled with hydride generation-atomic fluorescence spectrometry (HPIEC-HG-AFS) method was developed for simultaneous speciation of selenium in seafood. Three selenium species including of selenocystine (Se-Cys), selenome-thionine (Se-Met), and selenite Se(IV) were separated on an anion-exchange column (PRP-X100) with eluent of 30 mM NH₄H₂PO₄ and methanol (39:1, v/v) in 10 min at the flow rate of 1.0 mL min^?1. Variables affecting the HG-AFS detection of selenium species were optimized. The optimum conditions found were the following: reducing agent, 2.0 % of KBH₄, and 5.0 % of HCl; lamp current, 90 mA; photomultiplier tube voltage, 280 V; flow rate of carrier gas, 300 mL min^?1; and shielding gas, 800 mL min^?1. Under the optimized conditions, the good linearity of calibration curves (R ²?>?0.999) between signal of fluorescence and concentration of selenium species was obtained in the range of detection limits (DLs), 80 μg L^?1, and the DLs of Se-Cys, Se-Met, Se(IV) were 1.66, 0.990, 1.10 μg L^?1, respectively. The repeatability of the method, expressed as relative standard deviation, was less than 5.0 % (n?=?10), and the average recoveries for spiked test were from 87.3 to 103 % for three analytes in real seafood samples. The developed HPIEC-HG-AFS method was successfully applied for the speciation of selenium in seafood samples.     

Glucose Biosensor Based on a Glassy Carbon Electrode Modified with Multi-Walled Carbon Nanotubes-Chitosan for the Determination of Beef Freshness

In this study, the glucose biosensor was developed for the determination of the beef meat freshness based on a glassy carbon electrode (GCE) modified with multi-walled carbon nanotubes (MWCNTs) and chitosan (Chi). Glucose oxidase (GOx) was immobilized onto the MWCNTs-Chi/GCE surface by cross-linking the enzyme through glutaraldehyde with bovine serum albumin (BSA). Glutaraldehyde solution (0.25%, w/w) was also added to prevent enzyme release. The properties of the developed biosensor were characterized with cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS) using [Fe (CN)₆]^3?/4?as the supporting electrolyte. The influence of various parameters was investigated, and 0.1 mol L^?1 PBS with pH = 6.4 was chosen as the optimal supporting electrolyte for this experiment. The linear relationship between the current and the concentration of glucose was obtained from 0.2 to 1.2 mmol L^?1, with a detection limit of 0.05 mM at a signal-to-noise ratio of 3 and displayed good linearity (R ² = 0.9902), while the biosensor showed a rapid response to glucose. In addition, the developed glucose biosensor was applied in the determination of glucose in beef as an indicator of beef freshness compared to the total volatile basic nitrogen (TVB-N) method. The glucose level was decreased with increasing beef storage time.     

Determination of Major Sialic Acids in Dairy Products by Electrophoretic Stacking Technology with Contactless Conductivity Detection

Synergistic stacking technique by combining field-amplified sample injection with moving chemical reaction boundary was developed for the sensitive determination of two major sialic acids, N-acetylneuraminic acid (NANA) and N-glycolylneuraminic acid (NGNA) based on capillary electrophoresis with capacitively coupled contactless conductivity detection. A series of experimental parameters affecting electrophoretic separation, detection sensitivity, and hydrolysis efficiency of sialic acids were investigated. Under the optimum conditions, NANA and NGNA could be well separated from the common monosaccharides and disaccharides as well as other potential coexisting inorganic and organic anions in a running buffer of 30 mmol L^?1 NaOH–10 mmol L^?1 Na₂HPO₄/0.8 mmol L^?1 CTAB. This developed method has been applied to determine the target analytes in dairy products. In terms of its high sensitivity (LODs 1.7–2.2 ng mL^?1, namely, 5.5–7.2 nmol L^?1), good linearity (r > 0.999), acceptable recovery (93–107%), and reliability of acid hydrolysis step, this proposed method provides a simple, rapid, sensitive, and environmentally friendly alternative for the analyses of the main sialic acids in dairy products without derivatization.     

Comparative inactivation studies of <Emphasis Type="Italic">Aegle marmelos</Emphasis> (<Emphasis Type="Italic">bael</Emphasis>) peroxidase in crude extract of fruit by heat processing and ultrasonication treatment

Bael (Aegle marmelos) is considered as a holy fruit comprised of vast number of phytonutrients. Whole bael tree including all its parts has medicinal significance. Lack of awareness and seasonal nature makes its processing rather challenging. Conventional heat processing may lead to inactivation of quality hampering enzymes such as peroxidase, but at the cost of loss in essential phytonutrients. In the present work it was observed that thermal inactivation of bael peroxidase obeyed first order kinetics with enzyme activation energy of 7.7 kJ mol^?1. Complete inactivation of bael peroxidase was achieved within 11 min at 85?°C while ultrasound treatment attained in lesser time of 4 min at 64.07 W cm^?2 ultrasonic intensity. Loss of marmelosin a well-known phytonutrient in bael fruit was found to be 83.29?% by heat (11 min, 85?°C) and only 50.20?% by ultrasonication (4 min, 64.07 W cm^?2 ultrasonic intensity). Ultrasonication has potential to overcome harmful effects of heat processing with retention of phyto-constituents and hence has promising future in various food processing applications.