Automated Sequential Injection Method for Determination of Caffeine in Coffee Drinks

An automated sequential injection analysis spectrophotometric assay for the determination of purine alkaloids in coffee drinks was developed. The sample was treated with a carrez reagent for matrix suppression followed by filtration; subsequently, alkaloids were separated from organic acids using a short C18 monolithic column (10 × 4.6 mm). The flow rate of the separation step was 10 μL s^?1 with 10% v/v of methanol as the mobile phase. The sum of alkaloids evaluated as caffeine was detected at 274 nm. The influence of the main parameters affecting the quantification of purine alkaloids was optimized. One sample analysis lasted 15 min when aspirated in triplicate. The linear range was 1–15 mg L^?1, and the determination coefficient (r ²) was 0.9969. The limit of detection and limit of quantitation were 0.128 and 0.425 mg L^?1, respectively. The repeatability evaluated as the relative standard deviation (RSD) was 3.58% (n = 12, 10 mg L^?1). Under optimal conditions, the method was successfully applied to determine purine alkaloids in different real samples including soluble coffee, coffee from an espresso machine, and brewed coffee drinks.     

Optimization of the QuEChERS Method for Determination of Pesticide Residues in Chicken Liver Samples by Gas Chromatography-Mass Spectrometry

The goal of this research was to evaluate the application of Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) method for the determination of organochlorine, organophosphate, and carbamate pesticides in fatty animal matrices such as liver of chicken obtained from National Research Institute of Animal Production in Balice (Poland). Pesticides extraction effectiveness was evaluated at two different spiking levels (0.010 and 0.020 mg kg^?1) and efficiency of the dispersive solid-phase extraction (d-SPE) clean-up step was evaluated by comparison adding different d-SPE sorbent combinations (PSA?+?GCB, PSA?+?C₁₈, PSA?+?SAX, and PSA?+?NH₂). The analysis of pesticide residues was performed by gas chromatography ion trap mass spectrometry (GC/IT-MS). The linear relation was observed from 0 to 400 ng mL^?1 and the determination coefficient R ²?>?0.997 in all instances for all target analytes. Better recoveries were obtained in samples at 0.020 mg kg^?1 spiking level. The recoveries were in the range 70–120 %, with relative standard deviation (RSD) values lower than 15 % at 0.020 mg kg^?1 spiking level for most pesticides. Similar recovery ratios were obtained with the four different combinations of sorbents tested in the clean-up step, with better precision when the (PSA?+?SAX) combination was tested. Limits of detection (LODs) ranged from 0.001 to 0.005 mg kg^?1 and limits of quantification (LOQs) ranged from 0.003 to 0.015 mg kg^?1. The proposed method was successfully applied analyzing pesticide residues in real chicken liver samples; detectable pesticide residues were observed, but in all of the cases, the contamination level was lower than the default maximum residue levels (MRLs) set by European Union (EU), Regulation (EC) N 396/2005.     

Application of Near-Infrared Hyperspectral Imaging with Variable Selection Methods to Determine and Visualize Caffeine Content of Coffee Beans

Hyperspectral imaging covering the spectral range of 874–1734 nm was used to determine caffeine content of coffee beans. Spectral data of 958.24–1628.89 nm were extracted and preprocessed. Partial least squares regression (PLSR) model on the preprocessed full spectra obtained good performance with coefficient of determination of prediction (R ² _p ) of 0.843 and root mean square error of prediction (RMSEP) of 131.904 μg/g. In addition, 10 variable selection methods were applied to select the best optimal wavelengths. The PLSR models on the different optimal wavelengths obtained satisfactory results. The PLSR model on the wavelengths selected by random frog (RF) performed the best, with R ² _p of 0.878 and RMSEP of 116.327 μg/g. The RF wavelength selection combined with the PLSR model also achieved satisfactory visualization of caffeine content between different coffee beans. The overall results indicated that optimal wavelength selection was an efficient method for spectral data preprocessing, and hyperspectral imaging was illustrated as a potential technique for real-time online determination for caffeine content of coffee beans.     

Assessment of caffeine intake in the Korean population

An improved method for the analysis of caffeine in foods by HPLC was validated by measuring several analytical parameters. The caffeine contents of 1202 products available from Korean markets were analysed. A consumption study was conducted by using data from the Korea National Health and Nutrition Examination Survey (KNHANES), 2010–12, to estimate the caffeine intakes of the Korean population. The mean intakes of caffeine from all sources in the general population and consumers were 67.8 and 102.6 mg day^?1 for all age groups, respectively. The 95th percentile intakes of the general population and consumers were 250.7 and 313.7 mg day^?1, respectively. In those aged 30–49 years, the caffeine intakes of the general population and consumers were highest at 25.5% (101.8 mg kg^?1 day^?1) and 36.6% (0.9 mg kg^?1 day^?1), respectively, compared with the maximum recommended daily intake (400 mg day^?1) for adults. In the general population, the main contributors to the total caffeine intake were carbonated beverage for the younger age groups and coffee for the adults. These data provide a current perspective on caffeine intake in the Korean population.     

Validated RP-HPLC Method for Simultaneous Determination of Tocopherols and Tocotrienols in Whole Grain Barley Using Matrix Solid-Phase Dispersion

The vitamers of vitamin E such as α-, β-, γ-, and δ-tocotrienol and α-, β-, γ-, and δ- tocopherol are important phytochemical compounds with antioxidant activity and with potential benefits for human health. A high-performance liquid chromatography with fluorescence detection (HPLC-FLD) method was validated for their determination in whole grain barley samples. Tocol extraction was performed by an optimized matrix solid-phase dispersion (MSPD) protocol with neutral alumina (0.5 g) as the dispersion agent and methanol (5 mL) as the elution solvent. The analytical column was an Eclipse XDB C18 column (150?×?4.6 mm, 5 μm) and it was operated at room temperature. Mobile phase was consisted of methanol/acetonitrile/i-propanol (55:40:5?v/v?%) and the elution was isocratic at a flow rate of 0.8 mL/min. Total analysis time was 12 min, and the detection of the tocols was performed with a fluorimetric detector where the excitation and emission wavelengths were set at 295 and 335 nm, respectively. Method validation was performed by means of intra-day (n?=?5) and inter-day accuracy and precision (n?=?8), sensitivity, and linearity. The linear regression coefficient (R ²) was higher than 0.99. The recoveries of the tocols from barley samples with the proposed extraction method were in an acceptable level (74–91 %) where the relative standard deviation ranged from 4.2 to 15.0 %. Limits of detection (LODs) and limits of quantification (LOQs) varied from 0.03 to 0.11 mg kg^?1 and 0.11 to 0.34 mg kg^?1, respectively.     

Improved sensitivity of ochratoxin A analysis in coffee using high-performance liquid chromatography with hybrid triple quadrupole-linear ion trap mass spectrometry (LC-QqQLIT-MS/MS)

A novel and sensitive method utilising high-performance liquid chromatography coupled to triple quadrupole-linear ion trap mass spectrometry (LC-QqQLIT-MS/MS) was developed in order to analyse the content of ochratoxin A (OTA) in coffee samples. The introduction of the triple-stage MS scanning mode (MS³) has been shown to increase greatly sensitivity and selectivity by eliminating the high chromatographic baseline caused by interference of complex coffee matrices. The analysis included the sample preparation procedure involving extraction of OTA using a methanol–water mixture and clean-up by immunoaffinity columns and detection using the MS³ scanning mode of LC-QqQLIT-MS/MS. The proposed method offered a good linear correlation (r² > 0.998), excellent precision (RSD < 2.9%) and recovery (94%). The limit of quantification (LOQ) for coffee beans and espresso beverages was 0.010 and 0.003 µg kg^?1, respectively. The developed procedure was compared with traditional methods employing liquid chromatography coupled to fluorescent and tandem quadrupole detectors in conjunction with QuEChERS and solid-phase extraction. The proposed method was successfully applied to the determination of OTA in 15 samples of coffee beans and in 15 samples of espresso coffee beverages obtained from the Latvian market. OTA was found in 10 samples of coffee beans and in two samples of espresso in the ranges of 0.018–1.80 µg kg^?1 and 0.020–0.440 µg l^?1, respectively. No samples exceeded the maximum permitted level of OTA in the European Union (5.0 µg kg^?1).     

Applicability of Pressurized Liquid Extraction for Melamine Analysis in Pet Foods with High-Performance Liquid Chromatography with Diode Array Detection

A pressurized liquid extraction (PLE) method was developed for melamine analysis in pet foods. The PLE method which utilized an accelerated solvent extraction (ASE®) system was also compared with sonication and polytron extraction methods. The parameters for the optimized PLE method were temperature (75?°C for wet pet food, 125?°C for dry pet food), pressure (1,500 psi), static time (10 min), flush volume (40%), purge time (1 min), and number of cycles (1). Recoveries obtained by PLE method were significantly higher (P?≤?0.05) than those of sonication and polytron methods for dry pet food samples. For the analysis of adulterated pet foods, PLE resulted in the highest melamine content followed by sonication and polytron. Using PLE, samples fortified with melamine at 2.5 and 100 mg kg^?1 resulted in recoveries ranging from 55% to 90% for wet samples and from 90% to 116% for dry samples. Low recovery rate from wet samples at low spike level (2.5 mg kg^?1) may have been caused by co-aggregation of polysaccharide and protein with melamine due to low pH during solid-phase extraction cleanup. Limit of detection and limit of quantification values were 0.5 (mg kg^?1) and 1.0 (mg kg^?1) for dry samples. Overall, PLE had the best extraction efficiency compared to sonication and polytron, proving PLE to be a useful tool for melamine analysis of pet foods.     

Antioxidant Activity and Determination of Phenolic Compounds from <Emphasis Type="Italic">Eugenia involucrata</Emphasis> DC. Fruits by UHPLC-MS/MS

Fruits have been the focus of several studies aimed at finding new antioxidant sources for protection against the damage caused by reactive species. In this study, the antioxidant activity and the presence of phenolic compounds in all parts (peel, pulp, and seeds) of Eugenia involucrata DC. fruits were evaluated. DPPH^·, ABTS^·+, and ORAC methods were used to determine the antioxidant activity, and an UHPLC-MS/MS method was developed for determining the phenolic compounds (gallic, chlorogenic, ferulic, p-coumaric and ellagic acids, quercetin, and myricetin). In the determination of both antioxidant activity and phenolic composition, the efficiency of solvents with different polarities—methanol/H₂O (80:20, v/v), ethanol/H₂O (80:20, v/v), methanol/acidified water with phosphoric acid pH 3.00 (80:20, v/v), and ethyl acetate—for the extraction of the phenolic compounds, was also evaluated. All parts of E. involucrata fruits showed antioxidant activity, in the range of 36.68 ± 1.44 to 873.87 ± 18.24 μmol TE g^?1, being the highest values found in the seeds and peel when more polar extraction solvents were used. Six, five, and three phenolic compounds were identified and quantified in the pulp, peel, and seeds, respectively, with the highest abundance as p-coumaric acid (14 ± 2 mg kg^?1) in the pulp, quercetin (47 ± 5 mg kg^?1) in the peel, and gallic acid (74 ± 4 mg kg^?1) in the seeds, also when more polar solvents were used. Although antioxidant activity methods suggested that the peel and seeds have more antioxidant potential, a wider variety of compounds were determined in the pulp.     

Simultaneous Detection of Azodicarbonamide and the Metabolic Product Semicarbazide in Flour by Capillary Electrophoresis

In the present work, capillary electrophoresis (CE) was used for the first time for the simultaneous analysis of azodicarbonamide (ADA) and semicarbazide (SEM), and the capillary electrophoresis separation conditions, extraction agents, and derivatization conditions were investigated. In 20 mmol L^?1 sodium tetraborate, 30 mmol L^?1 β-cyclodextrin (β-CD), 17 % isopropanol (v/v), and 25 mmol L^?1 sodium dodecyl sulfate (SDS) running buffer, ADA and SEM previously derivatized with 9-fluorenylmethyl chloroformate (FMOC) were separated in less than 25 min with good sensitivity. The linear ranges were 8.3?×?10^?4～6.6?×?10^?2 mmol L^?1 and 1.9?×?10^?3～3.4?×?10^?2 mmol L^?1, and detection limits (S/N?=?10) were 0.5 and 0.15 mg kg^?1 for ADA and SEM, respectively. The proposed method was successfully applied for the simultaneous analysis of ADA and SEM in five flour samples with satisfactory recovery data from 88.0 to 93.0 % for ADA and 98.0 to 106.0 % for SEM, indicating the valuable potential application of this method for food analysis.     

Determination of Chlorothalonil Residue in Cabbage by a Modified QuEChERS-Based Extraction and Gas Chromatography–Mass Spectrometry

Being susceptible to any matrix with pH >5, taking cabbage as an example, the low recovery of chlorothalonil residues adsorbed onto the cabbage matrix was almost completely improved by extracting with 1/1 (v/v) acetonitrile (containing 5 % acetic acid)/toluene. Under the optimized conditions, the recoveries of chlorothalonil in cabbage fortified at three concentrations of 0.5 to 10 mg kg^?1 were 71–93 % with relative standard deviations (RSDs) lower than 6 %. The limit of detection (LOD) and the limit of quantification (LOQ) of the gas chromatography–mass spectrometry (GC–MS) method for chlorothalonil were 0.05 and 0.5 mg kg^?1, respectively, which were much lower than the maximum residue limits (MRLs). The proposed analytical method demonstrated a potential for its application to monitor for chlorothalonil and to help assure food safety, especially base-sensitive-pesticide analysis.     

Evaluation of acrylamide and selected parameters in some Turkish coffee brands from the Turkish market

The purpose of this study was to measure acrylamide (AA) levels and selected parameters of different traditional Turkish coffees. AA, 5-hydroxymethylfurfural (HMF), total reducing sugar, protein, pH, moisture, dry matter (DM) as well as ash, caffeine and soluble solids content (SSC) in DM, L*, a*, b* colour parameters of coffee samples were determined and the correlation between AA level and these parameters were investigated. A total of 36 coffee samples (20 Turkish, 8 Dibek and 8 Terebinth coffee) from the Turkish market were examined. A liquid chromatography-tandem mass spectrometry (LC-MS/MS) method was validated for the detection and quantitation of AA in coffee samples. The calibration curve was linear (R² ≥ 0.999) over the range of 30–1000 μg kg^?1. The limit of detection (LOD) and limit of quantification (LOQ) were found as 4.6 μg kg^?1 and 15.5 μg kg^?1, respectively. The amounts of AA in analysed coffee samples were in the range 31.1 ± 0.6 to 323.4 ± 5.4 µg kg^?1. The highest mean AA levels were found in Terebinth coffees (240.3 μg kg^?1) followed by Turkish coffees (204.3 µg kg^?1) and then Dibek coffees (78.6 µg kg^?1). No tested Turkish coffee samples had an AA concentration above the indicative value (450 µg kg^?1) for roast coffee recommended by the European Commission (EC) in 2011. In addition, a strong positive correlation was found between HMF values and AA amounts of selected coffee types.     

Simple Solvent Extraction Coupled with Liquid Chromatography-High-Resolution Mass Spectrometry for the Analysis of Pesticide Residues in Rice Bran Protein Powder

A simple analytical method combining solvent extraction and liquid chromatography-high-resolution mass spectrometry (LC-HRMS) was developed for the analysis of pesticide residues in rice bran protein powder. Owning to the high accuracy of HRMS in determination of mass to charge ratio (m/z), a suspect screen of pesticide residues was performed by LC-HRMS prior to quantification analysis. Based on the theoretical m/z, four pesticides including isoprothiolane (IPT), tebuconazole (TBZ), propiconazole (PCZ), and tricyclazole (TCZ) were detected and further verified with their reference standards. The solvent extraction conditions were optimized according to the signal intensity of extracted ion chromatogram (XIC) in LC-HRMS. After optimization, 50% acetonitrile solution was adopted, in which the targeted pesticides could be extracted effectively (recoveries/accuracy of >?85%) with the good reproducibility (relative standard deviation (RSD)?<?10.3%). Two isotope internal standards isoprothiolane-D₄ (IPT-D₄) and propiconazole-D₅ (PCZ-D₅) were applied in quantification, and the quantification results were highly consistent with those from the standard addition method. Limit of detections (LODs) and limit of quantifications (LOQs) of the method were about 0.05–0.2 and 0.2 to 1 μg kg^?1, respectively, without additional purification/enrichment for these analytical targets. The developed method was applied for the analysis of five different batches of rice bran protein samples. It was found that these four pesticide residues were all below 0.02 mg kg^?1, well less than the maximum residue levels (MRLs) in the latest regulations in EU and China (0.1–5 mg kg^?1). Besides the rice bran protein powder, this suspect screen followed with targeted quantification approach by LC-HRMS could also be applied for other rice derivative products analysis.     

Spectral Indices for Non-destructive Determination of Lettuce Pigments

Lettuce pigments play important physiological functions, such as photosynthetic processes and light stress defense. Spectral indices are widely used for predicting vegetable pigments in a non-destructive way. This work was carried out to propose and validate mathematical models based on spectral indices, capable of predicting carotenoid and anthocyanin contents in different lettuce cultivars, grown under organic, hydroponic and alternative farming systems. Standardized Difference Vegetation Index, Simple Ratio Index, and Difference Spectral Index were modified and combined with linear, exponential, power, and logarithm regressions during the modeling process. The most accurate models presented d and r values greater than 0.7 and 0.6 for the external validation, respectively. When estimating carotenoid and anthocyanin contents, the root-mean-square error did not exceed 0.14 and 0.41 mg kg^?1, respectively. The maximum mean bias error values were ?0.07 mg kg^?1 for carotenoids and 0.08 mg kg^?1for the anthocyanins. Models based on the Difference Spectral Index with exponential fitting performed better, but linear fittings combined to the other spectral indices also confirmed the feasibility of using the proposed models for estimating lettuce pigment contents.     

Post-harvest practices linked with ochratoxin A contamination of coffee in three provinces of Cordillera Administrative Region,Philippines

One of the emerging concerns in the Cordillera Administrative Region, Philippines is ochratoxin A (OTA) contamination in coffee. During 2015 to 2016, a total of 51 Arabica (Coffea arabica) coffee samples from Benguet province and 71 Robusta (Coffea canephora var. Robusta) coffee samples from the provinces of Ifugao and Kalinga were analysed for OTA contamination. The OTA-producing fungal contaminants during drying and storage of Arabica and Robusta coffee were Aspergillus niger and Aspergillus ochraceus. Ochratoxin A was more commonly detected in Robusta coffee (36.6%) than in Arabica coffee (21.6%). Among the contaminated samples, Robusta coffee cherries in the drying yard had the highest mean OTA level (120.2 μg kg^?1, n = 10) while roasted Robusta coffee beans had the lowest mean level (4.8 μg kg^?1, n = 9). The onset of contamination of Arabica coffee occurred during storage, with a mean OTA level of 46.7 μg kg^?1 (n = 9). Roasted coffee had lower OTA content although five samples had levels >5.0 μg kg^?1. Pearson Chi-square analysis (χ²) and Fisher’s exact test revealed that several post-harvest practices involving non-removal of the husk or hull and mixing of defective coffee were significantly associated with the occurrence of OTA during drying and storage (p < 0.05). No significant associations, however, were identified during roasting. This study suggests that the post-harvest practices in Cordillera Administrative Region should focus on the removal of defective coffee in all stages of post-harvest and rapid reduction of moisture content particularly during drying.     

Modification of Multiresidue QuEChERS Protocol to Minimize Matrix Effect and Improve Recoveries for Determination of Pesticide Residues in Dried Herbs Followed by GC-MS/MS

An accurate, rapid, and reliable multiresidue QuEChERS method based on gas chromatography coupled with tandem mass spectrometry was developed for the determination of 235 pesticides in challenging, dry, complex herb matrices (Centaurea cyanus L., Matricaria chamomilla L., Thymus vulgaris L.). Sample mass and the type of cleanup sorbent used to estimate the procedure’s effectiveness were optimized. Purification steps with ChloroFiltr, ENVI-Carb, GCB, octadecyl, PSA, and Z-Sep as cleanup sorbents and a step without purification were compared. To minimize the matrix effect and obtain acceptable recoveries for pesticides, 2 g of herb sample and 10 mL acetonitrile, followed by d-SPE cleanup step with a combination of 150 mg PSA/45 mg ENVI-Carb/900 mg MgSO₄, and additionally 50 μL of 5% formic acid and some droplets of dodecane, were needed. Matrix effects for the vast majority of pesticides were reduced (>?20%), showing suppression or enhancement. Most recoveries were in the range of 70–120% (RSD < 18%), reaching the quantification limit of 0.001 to 0.002 mg kg^?1. There was excellent linearity within the range from 0.001 to 2.00 μg mL^?1, and a correlation coefficient higher than 0.999 was obtained. Expanded measurement uncertainty was estimated to be between 4 and 43%. Finally, the developed method was successfully employed to identify and quantify pesticide residues in the analysis of 46 real herb samples.     

One-Step QuEChERS-Based Approach to Extraction and Cleanup in Multiresidue Analysis of Sulfonylurea Herbicides in Cereals by Liquid Chromatography–Tandem Mass Spectrometry

A one-step quick, easy, cheap, effective, rugged, and safe (QuEChERS)-based approach to extraction and cleanup in multiresidue pesticide analysis is presented for the first time. The experiment was designed to detect 23 sulfonylurea herbicides in a complex cereal matrix. The challenge was to choose the optimal conditions of one-step extraction and cleanup. Chitin, diatomaceous earth, and octadecyl were investigated as cleanup sorbents. Chitin, citrate buffer, and 1 % formic acid in acetonitrile yielded the best results. The effectiveness of sulfonylureas extraction was evaluated at three different spiking levels (0.005, 0.05, and 0.5 mg kg^?1) in wheat, rye, and oat using liquid chromatography–tandem mass spectrometry. The one-step QuEChERS provided recoveries in the 70–120 % range for 23 sulfonylureas in all cereal matrices. Matrix effects were evaluated and were not significant for all herbicides, showing suppression or enhancement (between ?19 and 13 %). Precision, calculated as relative standard deviation (RSD), was below 20 %. A linear dependence was observed in the range of 0.005–2.0 mg kg^?1, and the correlation coefficient was R ² > 0.999. Expanded measurement uncertainty was estimated to be between 9 and 24 %, on average. The validated method was employed in analysis of 89 real grain samples.     

Rapid Screening and Determination of the Residues of Hormones and Sedatives in Milk Powder Using the UHPLC-MS/MS and SPE

A method based on the ultra-high-performance liquid chromatography tandem mass spectrometry for determination of the residues of sex hormones, glucocorticoids, and sedatives in milk powder was developed. The sample was extracted with the acetic acid-acetonitrile (1:99, v/v) twice, purified by the PRiME hydrophilic-lipophilic balance (HLB) cartridges and analyzed by the ultra-high-performance liquid chromatography-tandem mass spectrometry. The analytes were separated by the Waters Acquity UPLC? BEH C18 column (50 mm?×?2.1 mm, 1.7 μm) and determined using the electrospray ionization in the positive mode with the multiple reaction monitoring (MRM). The developed method was validated with the specificity, linearity and range, matrix effects, recovery, and precision. The results showed that the analytes were linear with the correlation of determinations (R²) higher than 0.991 in the corresponding ranges. The limits of detection (LODs) and limits of quantification (LOQs) were in the range of 0.1–1.1 μg kg^?1 and 0.3–3.8 μg kg^?1, respectively. The average recoveries of the analytes ranged from 78.5 to 107.0% with the relative standard deviations lower than 15%. The practical applicability was tested by analyzing real samples and the progesterone was observed in two samples.     

Characterization and transformation of the <Emphasis Type="Italic">Opuntia ficus indica</Emphasis> fruits

Opuntia ficus indica fruits have been associated with health effects, due to their protective actions against oxidation. Nevertheless, few studies about processing of Opuntia fruits are available’; therefore, we studied the pulp characteristics and processing of a local variety, for producing beverage nectars. The pulp had an average pH of 5.64, 13.47 °Brix, with total sugars (106 g L^?1), K (1180 mg L^?1), 503.3 µg L^?1 of β carotene, 120 mg L^?1 of total phenolic compounds, 4.9 mg and 46.9 mg L^?1 respectively for betacyanins and betaxanthins and 243.4 mg L^?1 of vitamin C. The formulated nectars with 35% of pulp (N35) and 45% of pulp (N45) had respectively 14 and 15 °Brix. Minor components represent 1109 and 1112 mg L^?1 of K for N35 and N45 respectively, β carotene (318.6 µg and 362.8 µg L^?1), and vitamin C 227 and 231 mg L^?1. We confirmed the stability and acceptability of these beverages after a month of storage, after stability and panel tests. Therefore, we suggest that the pulp processing can be used as a new form of agro industrial utilization of this underutilized fruit.     

A Cassava Starch–Chitosan Edible Coating Enriched with <Emphasis Type="Italic">Lippia sidoides</Emphasis> Cham. Essential Oil and Pomegranate Peel Extract for Preservation of Italian Tomatoes (<Emphasis Type="Italic">Lycopersicon esculentum</Emphasis> Mill.) Stored at Room Temperature

The effect of edible cassava starch–chitosan coatings incorporated with rosemary pepper (Lippia sidoides Cham.) essential oil and pomegranate peel extract on the shelf-life of tomatoes during storage at 25 °C for 12 days was investigated. Sixteen formulations, containing 10 g L^?1 cassava starch and various concentrations of chitosan (5, 10, 20, 30 g L^?1), essential oil (0, 2.5, 5, 10 mL L^?1) and pomegranate peel extract (0, 5, 10, 20 mL L^?1) were prepared and applied to tomatoes. Physical–chemical and microbiological analyses were performed on days 1, 4, 8 and 12. Most of the coatings delayed the ripening of tomatoes, lowering the total soluble solids (38?44 g sucrose kg^?1) and weight loss (93?128 g kg^?1) and maintaining constant firmness compared to the uncoated tomatoes (45 g sucrose kg^?1, 175 g kg^?1) at 12 days of storage. Conversely, except red intensity (a*), which was higher for the uncoated samples, the colour parameters (L*, b*) of the coated and control tomatoes were similar at the end of storage. Uncoated and coated tomatoes showed no contamination during storage. The coatings showed potential to maintain the quality of tomatoes during storage at 25 °C for 12 days. In this context, tomatoes coated with the formulation comprising 10 g L^?1 cassava starch, 10 g L^?1 chitosan, 10 mL L^?1 essential oil and 20 mL L^?1 pomegranate peel extract showed the lowest weight loss and reduced total soluble solids content compared with uncoated ones.     

Usage of Capillary Isotachophoresis and Antioxidant Capacity Measurement in Analysis of Changes in Coffee Properties After Roasting,Steaming and Decaffeination

The aim of the study was to optimise and validate the method for quantitation of short-chained organic acids in coffee brews by capillary isotachophoresis (ITP). The linearity of the method was satisfactory with R ² from 0.9924 for lactic acid to 0.9998 for acetic acid. The limit of detection (LOD) was from 4.9 μmol L^?1 for acetic acid to 24.8 μmol L^?1 for lactic acid. Precision of the method was from 0.20 to 2.69 %. This method was successfully applied to determine six organic acids (tartaric, formic, citric, malic, lactic and quinic) in Arabica and Robusta green and roasted coffee brews. The roasting as well as steaming and decaffeination processes of beans influenced degradation of acids (citric and malic) and their formation (quinic, tartaric, lactic and formic) in coffee brews. The influence of coffee processing on the antioxidant capacity of coffee brews was also tested by using the 2,2′-azinobis(3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt (ABTS), 2,2-diphenyl-1-picrylhydrazyl (DPPH), Folin-Ciocalteu and chelating Fe(II) assays. The roasted coffee brews possessed higher antioxidant capacity than unprocessed coffee brews, excluding chelating activity.