Simple and fast spectrophotometric determination of low levels of thiabendazole residues in fruit and vegetables after pre-concentration with ionic liquid phase microextraction

There is a great importance of monitoring thiabendazole (TBZ) residues in fruits and vegetables to ensure food safety. Therefore, a new ionic liquid (IL) phase microextraction method using IL, 1-butyl-3-methylimidazoliumhexafluorophosphate [C₄mim][PF₆], as extracting solvent is proposed for simple and fast determination of low levels of TBZ in fruits and vegetables by spectrophotometry. The method is based on selective complex formation of TBZ with Cu(II) ions in presence of PF₆^– as counter ion at pH 5.5, and then microextraction of the complex into the fine micro-drops of IL phase. After optimisation of variables affecting microextraction efficiency, the analytical parameters of the method were determined by calibration curves. The method exhibits a linear relationship (0.3–280 μg L^?1), low detection limit (0.1 μg L^?1), good intra- and inter-day precision (2.4–4.5% as RSD_r%, 2.1–5.6% as RSD_R%), good recovery (≥95.1–98.2%) and high sensitivity enhancement factor (150) by solvent-based calibration curve. It allows a detection limit of 0.24 μg L^?1 and a range of 0.8–250 μg L^?1 by the matrix-matched calibration curve. After validation, the method was successfully applied to the determination of TBZ residues with method quantification limits in fruit and vegetables of 2.0 and 2.5 µg kg^?1 with and without adding polyvinylpyrrolidone (PVP-15) solution. Recoveries range from 85.5% to 98.2% after spiking (10, 50 and 100 µg kg^?1, n: 3).     

Dispersive Liquid-Liquid Microextraction for the Determination of Emerging <Emphasis Type="Italic">Fusarium</Emphasis> Mycotoxins in Water

A new method was optimized for the determination of emerging Fusarium mycotoxins enniatins (ENs) and beauvericin (BEA) in different types of water. Mycotoxin analysis was performed by dispersive liquid-liquid microextraction (DLLME) combined with liquid chromatography-tandem mass spectrometry (LC-MS/MS). Mycotoxins were efficiently extracted from water into carbon tetrachloride by DLLME technique using acetonitrile as disperser solvent. Detection limits were in the range of 0.06–0.17 μg L^?1. Quantification was performed using matrix-matched calibration curves over a linear range from limit of quantification (LOQ) to 200 μg L^?1. Acceptable recoveries were obtained between 78.5 and 100.1 % with relative standard deviations of <14 %. The proposed method may be advised as an easy, sensitive, and accurate method for determining emerging Fusarium mycotoxins in water. The method was successfully applied to the analysis of different kinds of water. No detectable levels were achieved in surface, ground, tap, and bottled water. Concentration levels up to 50 μg L^?1 were detected in cooking water related to the pasta cooking process.     

A Rapid Quantification of β-Carotene in Fruits and Vegetables by Dispersive Liquid–Liquid Microextraction Coupled with UV–Vis Spectrophotometry: Optimized by Response Surface Methodology

A simple, fast, and efficient method consisted of optimized dispersive liquid–liquid microextraction (DLLME) followed by UV–vis spectrophotometry was developed for determination of β-carotene in fruits and vegetables. Chloroform and methanol were chosen as extraction and disperser solvents, respectively. The extraction process was optimized using a central composite design (CCD) with the optimum points of 115 μL for volume of extraction solvent and 6.5 % (w/v) for salt concentration. Under the optimal conditions, the relative standard deviation (RSD, C?=?500 μg L^?1, n?=?5), limit of detection (LOD), linear dynamic range (LDR), and coefficient of determination (R²) were 1.08 %, 2 μg L^?1, 50–1,500 μg L^?1, and 0.991, respectively. The present method consisted of a simple and fast sample preparation procedure without any antioxidant addition, saponification, and purification was used.     

Dual-Label Chemiluminescence Strategy for Multiplexed Immunoassay of 20 Fluoroquinolones, 15 β-Lactams, 15 Sulfonamides,and CAP in Milk

In this paper, a novel dual-label time-resolved chemiluminescent multiplexed immunoassay (DLTRC-MIA) based on the distinction of the kinetic characteristics of horseradish peroxidase (HRP) and alkaline phosphatase (ALP) with approximate estimation approach for simultaneous determination of 20 fluoroquinolones (FQs), 15 β-lactams, 15 sulfonamides (SAs), and chloramphenicol (CAP) in milk was developed. The strategy integrated a single-chain variable fragment–alkaline phosphatase fusion protein (scFv-ALP), a recombinant penicillin-binding protein (PBP) 2×*, a monoclonal antibody (MAb), and a polyclonal antibody (PAb) in one immunoassay and in a single well together to fulfill the simultaneous detection of 51 low-molecular weight contaminants (20 FQs, 15 β-lactams, 15 SAs, and CAP). The limits of detection for FQs, β-lactams, SAs, and CAP range from 0.29 μg L^?1 for ciprofloxacin (CIP) to 81.6 μg L^?1 for trovafloxacin (TRO), 0.27 μg L^?1 for ceftiofur (CEF) to 44.1 μg L^?1 for cephalexin (CEL), 0.089 μg L^?1 for sulfadimethoxine (SDM) to 2.7 μg L^?1 for sulfadiazine (SDZ), and 0.028 μg L^?1 for CAP, respectively. The results demonstrated that the detection limits of DLTRC-MIA meet the requirement of detection levels for 51 drug residues in milk, suitable for high-throughput screening of low-molecular weight contaminants.     

Hybrid Amine-Functionalized Titania/Silica Nanoparticles for Solid-Phase Extraction of Lead,Copper, and Zinc from Food and Water Samples: Kinetics and Equilibrium Studies

In the present study, hybrid amine-functionalized titania/silica nanoparticles were employed as a new and novel adsorbent for solid-phase extraction of Pb²⁺, Cu²⁺, and Zn²⁺ ions prior to their determination using flame atomic absorption spectrometry. Under the best conditions (including adsorbent, 0.4 g; eluent, 5.0 mL nitric acid (HNO₃), 3.0 mol L^?1, 1.0 mL min^?1; and sample, pH 5.0, 3.0 mL min^?1), detection limits, adsorption capacities, and preconcentration factors were 0.12–0.24 μg L^?1, 7.1–20.7 mg g^?1, and 200, respectively. To predict the adsorption isotherms, different isotherm models were studied and the obtained results showed that the Langmuir model is the most suitable one to explain the experimental data. The kinetics of the reaction followed pseudo-second-order kinetic model. Thermodynamic parameters like free energy (ΔG ⁰) and enthalpy (ΔH ⁰) confirmed the spontaneous and exothermic nature of the process. The method was successfully applied for determination of the analytes in different food and water samples.     

Development of an ELISA and Immunochromatographic Assay for Tetracycline,Oxytetracycline, and Chlortetracycline Residues in Milk and Honey Based on the Class-Specific Monoclonal Antibody

A sensitive class-specific monoclonal antibody against tetracyclines (TCs) was generated and used to develop an enzyme-linked immunosorbent assay (ELISA) and an immunochromatographic assay for TC, oxytetracycline (OTC), and chlortetracycline (CTC) detection in milk and honey samples. The dynamic range of detection for TC in ELISA was 0.26–2.00 μg L^?1 with an IC₅₀ of 0.72 μg L^?1. The IC₅₀ value of OTC and CTC was 3.2 and 6.4 μg L^?1, respectively. The recovery of TC, OTC, and CTC in milk samples was 82–102, 91–105, and 90–101 %, respectively, and 88–101, 89–101, and 89–95 % in honey samples, respectively. In the immunochromatographic assay, the cutoff values for TC, OTC, and CTC were 15, 15, and 50 μg L^?1 in milk, respectively, and 40, 40, and 40 μg L^?1 in honey, respectively. The results revealed that ELISA and the immunochromatographic assay can be applied for the rapid and sensitive detection of TC, OTC, and CTC in milk and honey samples.     

Simultaneous pre-concentration of Pb and Sn in food samples and determination by atomic absorption spectrometry

A cloud point extraction (CPE) method has been developed for the pre-concentration and simultaneous determination of lead [Pb(II)] and tin [Sn(II)] using Acridine Orange as complexing reagent and mediated by nonionic surfactant (Triton X-114) by flame atomic absorption spectrometry (FAAS). The main factors affecting analytical performance of CPE have been investigated in detail. The extracted surfactant-rich phase was diluted with (1.0 mol L^?1) nitric acid in methanol, prior to subjecting FAAS. The calibration graphs obtained from Pb(II) and Sn(II) were linear in the concentration ranges of 5–1,000 and 10–5,000 μg L^?1 with detection limits of 1.40 and 2.86 μg L^?1, respectively. The relative standard deviations for 10 replicates containing 25 μg L^?1 of Pb(II) and Sn(II) were 2.15 and 2.50 %, respectively. The analytical procedure was verified by the analysis of the standard reference materials NWTMDA-61.2 (water-trace elements) and NIST SRM 1548a (typical diet). The developed method has been applied to the simultaneous determination of total Pb and Sn in canned food samples including juices, tomato paste, corn, and green pea.     

Large-Volume Sample Staking of Rice Polyphenols Prior to Their Determination by Non-aqueous Capillary Electrophoresis

A rapid non-aqueous capillary electrophoretic (NACE) method for the separation of (?)-epicatechin (EPI), (+)-catechin (?CAT), kaempferol (KAE), quercetin (QUR), naringanin (NAR), ferulic acid (FA), and p-coumaric acid (p-CA) has been developed and applied to the determination of these compounds in different rice varieties. All seven compounds were separated on capillary of 50 μm?×?68 cm (60-cm effective length) using 20 mmol L^?1 borate buffer of pH 9.0 and 5 % acetonitrile in methanol. Large-volume sample stacking (LVSS) technique was optimized and used to preconcentrate non-detectable polyphenols of white polished rice. Rice extracts were concentrated on-line by LVSS prior to separation by non-aqueous capillary electrophoresis. An improvement of 10–55 times in detectability was achieved with injection at 50 mbar for 30 s followed by voltage inversion (?20 kV) for 5 s. Linear calibration range of 1–300 μg L^?1 and 0.01–60 μg L^?1 was observed for NACE and NACE-LVSS method respectively, with the detection limit of 0.33–2.0 and 0.006–0.19 μg L^?1. Good reproducibility with standard deviations of less than 5 % was achieved. Polyphenol contents of different rice varieties were determined using developed method.     

Use of Multivariate Optimization to Develop Methods for Direct Copper and Lead Determination in Breast Milk by Graphite Furnace Atomic Absorption Spectrometry

A direct method for lead and copper determination in breast milk by graphite furnace atomic absorption spectrometry, using aqueous calibration, was proposed in this study. Samples were diluted with hydroximethylaminomethane 80 %?v/v, pH 8. The dilution determination for Pb and Cu was 1:1 and 1:9, respectively. Fractional factorial (2^4?1) and central composite designs were used to optimize experimental conditions (pyrolysis and atomization temperatures, pyrolysis time, and modifier) using 10 μL samples introduced into a graphite furnace. The methods allowed for copper and lead determination under optimized conditions with an aqueous calibration curve between 0 and 180 μg L^?1 for Cu and 0 and 48 μg L^?1 for Pb. The detection limits were 0.92 μg L^?1 and 6.4 μg L^?1 for Pb and Cu, respectively. Intra and inter-assay studies revealed coefficients of variation of 5.0 and 6.3 %, and 6.4 and 5.5 % for Pb and Cu, respectively. Recovery studies at three concentration levels (three consecutive days, n?=?7/day) presented results between 107 and 109 % for Pb and 102 and 103 % for Cu. Good accuracy was obtained for both metals through recoveries studies using certified reference material (infant formula NIST® 1846). The method determined lead and copper in six samples and the concentrations ranged from 2.90 to 27.9 μg L^?1 for Pb and 384 to 1,212 μg L^?1 for Cu. While copper is an essential element, lead has no nutritional function and is cumulative at low concentrations. Therefore, safe, efficient, and validated methods should be available to determine its concentration in breast milk.     

SERS Detection of Insecticide Amitraz Residue in Milk Based on Au@Ag Core-Shell Nanoparticles

A simple, rapid, and environmentally friendly surface-enhanced Raman scattering (SERS) method was developed for the determination of trace amitraz in milk with the use of silver-coated gold nanoparticles (Au@Ag NPs) as enhancing reagent. The normal Raman and SERS spectra of amitraz were analyzed, and the peaks were assigned by density functional theory. The morphology of Au@Ag NPs was characterized and confirmed by transmission electron microscopy, scanning electron microscopy, and ultraviolet-visible spectroscopy. The SERS effects of Au@Ag NPs were investigated, including the types of solvents for dissolving amitraz, the volume ratio of the Au@Ag NPs and amitraz, and the concentration of aggregating agent (NaCl) for aggregate Au@Ag NPs. Results show that ethanol exerts the least interference on the SERS spectrum of amitraz and is more environmentally sound than methanol. The strongest SERS signal appeared when the volume ratio of Au@Ag NPs and amitraz was 2:1. Moreover, the strongest SERS signals appeared when the concentration of NaCl was 0.025 mol L^?1 because of appropriate aggregation. Under the optimum conditions, the concentration of amitraz presents a good linear relationship with Raman intensity (723 cm^?1) with a linear range of 9.77 × 10^?4~2.93 × 10^?2 g L^?1. The detected recoveries of amitraz in milk were between 81.7 and 100.5% with a relative standard deviation (RSD) of 2.61~5.51%.     

Simultaneous Determination of Multiclass Pesticides and Antibiotics in Honey Samples Based on Ultra-High Performance Liquid Chromatography-Tandem Mass Spectrometry

A simple, fast, and efficient method was developed for simultaneous determination of 79 pesticides and 13 antibiotics compounds of different chemical classes of pesticides and antibiotics in honey samples by ultra-high performance liquid chromatography with tandem mass spectrometry (UHPLC-MS/MS). The sample preparation procedure includes homogenization with McIlvaine buffer 0.1 mol L^?1 (pH 4), followed by extraction with acetonitrile and cleanup with florisil, using dispersive solid phase extraction (d-SPE). The proposed method was validated with good results, such as linearity (r ²?>?0.9901), normality, and independence of the evaluated data, as well as recoveries between 70 and 120 % with relative standard deviation (RSD) <20 % for most of the compounds spiked from 0.1 to 200 μg kg^?1. The experimental method limits of detection and quantification were from 0.03 to 1.51 μg kg^?1 and from 0.1 to 5 μg kg^?1, respectively, for the pesticides. For the antibiotics, the decision limits (0.1 to 2 μg g^?1) and the detection capacity (0.12 to 2.81 μg g^?1) were below the maximum residue limits (MRLs) established for honey by the Brazilian and European legislation. The method was successfully applied to real samples from different botanical and geographic origins. From them, 44 % presented residues from 0.12 to 10 μg kg^?1 of one or more analytes. The proposed method combines the advantages of a quick sample preparation step with the selectivity and sensitivity of the UHPLC-MS/MS and proved to be suitable for routine analyses.     

Development of CO<Subscript>2</Subscript>-Mediated Switchable Hydrophilicity Solvent-Based Microextraction Combined with HPLC-UV for the Determination of Bisphenols in Foods and Drinks

In traditional dispersive liquid-liquid microextraction procedures, both extraction and dispersive solvents are required, and thus, it increases the consumption of organic solvent. Herein, we reported a CO₂-mediated switchable hydrophilicity solvent-based microextraction (SHS-BME) for the determination of bisphenol compounds (BPCs) in complex milk and drink samples. N,N-Dimethylcyclohexylamine was used as a switchable hydrophilicity solvent; it can switch reversibly between one form that is miscible with water and another that forms a biphasic mixture with water, and thus allow extraction of the analytes in a homogeneous phase without dispersive solvent. Several important parameters were screened and optimized by single factor experiments and central composite design as follows: 782 μL of switchable solvent, 375 μL of NaOH solvent, and 1.1:1 switchable solvent/water (v/v). Under the optimized SHS-BME conditions, the limit of detections (LODs) for BPCs in milk, orange juice, and energy drink samples were in the range of 0.27–0.40 μg L^?1 for BPE, 0.17–0.30 μg L^?1 for BPA, and 0.50–0.67 μg L^?1 for BPB, respectively, and the extraction recoveries for BPCs were in the range of 79.5–103.4% in milk, of 84.5–97.5% in orange juice, and of 91.9–101.2% in energy drinks. The precision of the method, based on relative standard deviations (RSDs), ranged from 1.7 to 4.8% and from 2.1 to 5.7% for intra-day and inter-day comparisons, respectively. In total, this SHS-BME method possesses many advantages, such as high extraction recovery and high detection sensitivity (low LODs and RSDs), no requirement of dispersive solvent, simple operational procedure, reducing the pretreatment time and workload, and so on. Therefore, it has a great potential application value for detection of trace BPCs in routine food tests.     

Gas Purge Microsyringe Extraction Coupled with Dispersive Liquid-Liquid Microextraction for the Determination of Acidic Compounds in Food Packaging Materials

A green, simple and sensitive method was developed for the analysis of volatile carboxylic acids (VFAs) and perfluorocarboxylic acids (PFCAs) in food packaging materials. The acidic compounds in food packaging materials were first extracted by gas purge microsyringe extraction (GP–MSE) with 1.0 mL 0.1 mol·L^?1 NaOH solution, then the analytes were dispersive liquid-liquid microextracted (DLLME) by 50 μL chloroform as extraction solvent and 200 μL acetonitrile as dispersive solvent. The 2-(5-Benzoacridine) ethyl-p-toluenesulfonate (BAETS) with excellent fluorescence property was applied to enhance the high performance liquid chromatography (HPLC) sensitivity. The obtained recoveries for the VFAs ranged from 92.0 to 101 %. The method LODs calculated at a signal-to-noise ratio (S/N) of 3 were in the range of 0.80–3.40 μg·kg^?1, while the LOQs calculated at S/N of 10 were in the range of 2.5–10.2 μg·kg^?1. All compounds were in good linearity with concentration coefficients of higher than 0.997. Perfluorooctanoic acid (PFOA) was found in all of the 15 kinds of samples analyzed with concentrations ranging from 4.86–7.56 μg·kg^?1. Acetic acid, butyric acid, and caprylic acid were found in half of the samples analyzed. The other analytes were also found in more than 30 % samples with concentrations varied between 3.96 and 293 μg·kg^?1.     

Ultra-Trace Determination of Co (ІІ) in Real Samples Using Ion Pair-Based Dispersive Liquid-Liquid Microextraction Followed by Electrothermal Atomic Absorption Spectrometry

Ion pair-based dispersive liquid-liquid microextraction technique was used for preconcentration and determination of ultra-trace levels of Co (??) followed by electrothermal atomic absorption spectrometry (ETAAS). Thiocyanate (SCN^?) forms an anionic complex with Co (??) followed by addition of cetylpyridinium chloride (CPC) as a positive counterion to produce hydrophobic cobalt-thiocyanate-CPC complex. The resulting hydrophobic complex was extracted into the fine droplets of carbon tetrachloride by dispersive liquid-liquid microextraction (DLLME). In DLLME, a mixture of 1.5 mL of acetone (as disperser solvent) containing 40 μL of carbon tetrachloride (as extraction solvent) was rapidly injected into the sample solution to extract the hydrophobic cobalt-thiocyanate-CPC complex. Under the optimum conditions, the calibration curve was linear in the range of 0.08–1.5 μg L^?1 of Co (??) with a correlation coefficient of 0.9997. The relative standard deviation (RSD, %) based on six replicate analyses of 0.5 μg L^?1 of Co (??) was 3.7 %, and the limit of detection (LOD) was 0.02 μg L^?1. The accuracy of the proposed method was evaluated by the analysis of a certified reference material and spike method. The proposed method was successfully applied for determination of ultra-trace levels of Co (??) in different water samples and spinach leaves.     

Determination of Herbicides in Milk Using Vortex-Assisted Surfactant-Enhanced Emulsification Microextraction Based on the Solidification of a Floating Organic Droplet

A vortex-assisted surfactant-enhanced emulsification–solidification liquid microextraction (VASEME-SFO) has been proposed for the determination of triazine and phenylurea herbicides in milk. 1-Dodecanol was used as the extraction solvent and dispersed into the aqueous samples by the assistance of a vortex mixer. Meanwhile, the addition of a surfactant, which was used as an emulsifier, could enhance the speed of the mass transfer from aqueous samples to the extract solvent. Acetic acid and Na₂SO₄ were applied and used to eliminate interference by proteins and fats. The influence of various parameters in the VASEME-SFO such as the type and volume of the extraction solvent, the type and concentration of the surfactant, and the vortex time, salt addition, and sample solution pH were investigated and optimized. Under optimal conditions, the limits of detection (LODs) and quantification (LOQs) reached ranges of 0.005–0.09 and 0.015–0.30 μg L^?1, respectively. Dynamic linear ranges (DLRs) of 0.2–200 and 2–400 μg L^?1 were obtained for triazine and phenylurea herbicides, respectively. The performance of the method was evaluated for extraction and determination of these herbicides in milk in micrograms per liter, and satisfactory results were obtained (RSD?<?10.6 %).     

Magnetic solid-phase extraction coupled with HPLC for the determination of Allura Red in food and beverage samples

A magnetic solid-phase extraction (MSPE) protocol prior to HPLC was developed for the extraction and determination of Allura Red in food samples. Magnetic nanoparticles were coated with tetraethylorthosilicate and 3-aminopropyltriethoxysilane and modified by graphene. Scanning electron microscopy, transmission electron microscopy and Fourier-transform infrared spectrometry were used to characterise the graphene-functionalised sorbents; and the main parameters affecting the extraction such as sample volume, temperature, pH and time were investigated and established. Under optimised conditions, the pre-concentration factor of Allura Red was 200, and the calibration curve was linear at a concentration range of 5–1500 μg kg^?1. The LOD was 2 μg kg^?1, the limit of quantification was 7 μg kg^?1, and the relative standard deviation was 3.3%. The prepared MSPE procedure was simple and fast, and it was successfully applied for the determination of Allura Red in beverages, candy and jelly.     

Application and Optimization of Microwave-Assisted Extraction and Dispersive Liquid–Liquid Microextraction Followed by High-Performance Liquid Chromatography for the Determination of Oleuropein and Hydroxytyrosol in Olive Pomace

In the present study, a new method based on microwave-assisted extraction and dispersive liquid–liquid microextraction (MAE–DLLME) followed by high-performance liquid chromatography (HPLC) was proposed for the separation and determination of oleuropein (Ole) and hydroxytyrosol (HyT) from olive pomace samples. The effective factors in the MAE–DLLME process such as microwave power, extraction time, the type and volume of extraction, and dispersive solvents were studied and optimized with the aid of response surface methodology (RSM) based on a central composite design (CCD) to obtain the best condition for Ole and HyT extraction. At the optimized conditions, parameter values were 220 W microwave power, 12 min extraction time, 60 μL extracting solvent, and 500 μL dispersive solvent. The calibration graphs of the proposed method were linear in the range of 10–500,000 μg L^?1, with the coefficient of determination (R²) higher than 0.99 for Ole and HyT. Repeatability of the method, described as the relative standard deviation (RSD), was 4.12–5.63% (n?=?6). The limits of detection were 35 and 20 μg L^?1 for Ole and HyT, respectively. The recoveries of these compounds in the spiked olive pomace sample were from 93 to 98%. The proposed method, MAE–DLLME–HPLC–UV, was an accurate, rapid, and reliable method when compared with previous methods.     

Antimony Assessment in PET Bottles for Soft Drink

The aim of this work was to develop a method for the determination of antimony (Sb) in polyethylene terephthalate (PET) bottles and to evaluate its migration into soft drink and simulant. In this context, a new procedure for PET sample preparation, using a high pressure asher (HPA), is presented for the determination of Sb by inductively coupled plasma optical emission spectrometry (ICP-OES). The concentration of Sb in PET bottles ranged between 272 and 650 mg kg^?1. The migration of Sb into soft drink after 180 days at 35 °C was below the LOQ, 20 μg L^?1. The specific migration of Sb from the bottle into simulant 3% of acetic acid after the contact per 10 days at 40 °C was less than the LOQ, 23.5 μg L^?1. The results showed that all packaging evaluated contained Sb, but the maximum permissible migration value for Sb, 40 μg L^?1, established by Anvisa and EU, was never exceeded.     

Electrochemical Determination of Phoxim in Food Samples Employing a Graphene-Modified Glassy Carbon Electrode

Employing a graphene-modified glassy carbon electrode, a sensitive and convenient electrochemical method for the determination of phoxim by linear sweep voltammetry was developed. The electrochemical behavior of phoxim at the modified electrode was studied by cyclic voltammetry. In citric acid–phosphate buffers, the modified electrode exhibited excellent electrocatalytical effect on the reduction of phoxim and this was further used for the determination of phoxim. Under optimized analytical conditions, the reduction peak current showed a linear relationship with the concentration of phoxim in a range of 5.97 to 5,966 μg L^?1, with a correlation coefficient of 0.9993 and a detection limit of 2.39 μg L^?1. The proposed method shows excellent sensitivity, selectivity, and linearity and has been successfully applied for the determination of phoxim in a variety of food samples with satisfactory results.     

Novel Binary Solvents-Dispersive Liquid—Liquid Microextraction (BS-DLLME) Method for Determination of Patulin in Apple Juice Using High-Performance Liquid Chromatography

A simple and rapid binary solvents-based dispersive liquid–liquid microextraction (BS-DLLME) method has been developed for determination of patulin (PAT) in apple juice followed by high-performance liquid chromatography. This method involves the use of an appropriate mixture of miscible binary extraction solvents and disperser solvent to form fine droplets of extractant in a sample solution. Parameters affecting extraction efficiency such as the type and volume of high-density extraction solvent, the volume of ethyl acetate, the kind and volume of disperser solvent, and salt addition were investigated and optimized. The detection and quantification limits were 2.0 and 10.0 μg L^?1, respectively. The relative standard deviation for five measurements of 25 μg L^?1 of PAT was 3.8 %. The relative recoveries of PAT from apple juice samples at spiking levels of 25, 50, and 75 ng mL^?1 were in the range of 91.3–95.2 %.