Optimization of Extraction Parameters of Total Phenolics from <Emphasis Type="Italic">Annona crassiflora</Emphasis> Mart. (Araticum) Fruits Using Response Surface Methodology

In this study, response surface methodology was used to optimize the extraction temperature (25–75 °C) and ethanol concentration (0–70 %, ethanol/water, v/v) to maximize the extraction of total phenolic compounds (TPC) from araticum pulp. The efficiency of the extraction process was monitored over time, and equilibrium conditions were reached between 60–90 min. A second-order polynomial model was adequately fit to the experimental data with an adjusted R ² of 0.9793 (p < 0.0001) showing that the model could efficiently predict the TPC content. Optimum extraction conditions were ethanol concentration of 46 % (v/v), extraction temperature of 75 °C and extraction time of 90 min. Under the optimum conditions, the araticum pulp showed high TPC content (4.67 g GAE/100 g dw) and also high antioxidant activity in the different assays used (46.56 μg/mL, 683.65 μmol TE/g and 1593.72 μmol TE/g for DPPH IC₅₀, TEAC and T-ORAC_FL, respectively). From our extraction procedure, we successfully recovered a significantly higher amount of TPC compared to other studies in the literature to date (1.5–22-fold higher). Furthermore, TPC and antioxidant activity were present in the fruit in levels that are difficult to find in other common fruits. These results expose a potential approach for improving human health through consumption of araticum fruit.     

Determination of Seven <Emphasis Type="Italic">N</Emphasis>-nitrosamines in Agricultural Food Matrices Using GC-PCI-MS/MS

The quantitative analytical methods for seven N-nitrosamines including N-nitrosodimethylamine (NDMA), N-nitrosomethylethylamine (NMEA), N-nitrosodiethylamine (NDEA), N-nitrosodibutylamine (NDBA), N-nitrosopiperidine (NPIP), N-nitrosopyrrolidine (NPYR), and N-nitrosomorpholine (NMOR) were established for agricultural food matrices. Four food matrices were used for the method development: rice soup as a fatless solid matrix, apple juice as a fatless liquid matrix, corn oil as a fat-rich liquid matrix, and 20 % alcohol as an alcohol matrix. A combination of solid-supported liquid-liquid extraction (SLLE) using Extrelut NT and a solid phase extraction (SPE) using Florisil was employed for fatless matrices. For an alcohol matrix, only SLLE was used without SPE, and liquid-liquid extraction (LLE) was established for a fat-rich matrix. The extract was analyzed by gas chromatography-positive chemical ionization-tandem mass spectrometry (GC-PCI-MS/MS) using ammonia gas as an ion source. Linearity, recovery, repeatability, inter-day precision, reproducibility, and uncertainty were evaluated for method validation using four matrices. Method detection limits for all of the investigated N-nitrosamines were ranged from 0.10 to 0.18 μg/kg for the rice soup, from 0.10 to 0.19 μg/kg for the apple juice, 0.10 μg/kg for the corn oil, and from 0.10 to 0.25 μg/kg for 20 % alcohol, depending on N-nitrosamines. Established methods were applied to determine seven N-nitrosamines in some agricultural food products.     

Preparation of Acryloyl <Emphasis Type="Italic">β</Emphasis>-Cyclodextrin Organic Polymer Monolithic Column and Its Application in Solid-Phase Microextraction and HPLC Analysis for Carbofuran and Carbaryl in Rice

An acryloyl β-cyclodextrin (A-β-CD) monolithic column for solid-phase microextraction (SPME) and determination of carbofuran and carbaryl by high-performance liquid chromatography (HPLC) have been prepared through a “one-step” polymerization method. The synthesis conditions, including the volume of cross-linker, the ratio and volume of mixed porogenic solvent consisted of methanol and N,N-dimethylformamide were optimized. The prepared monolithic column was characterized by thermogravimeteric analysis (TGA), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and Brunner-Emmet-Teller (BET) measurement. The eluent type, volume and flow rate, sample volume, flow rate, acidity, and ionic strength were optimized in detail. Under the optimized conditions, a simple, rapid, and sensitive SPME-HPLC method was developed for determination of carbofuran and carbaryl in rice samples. The method yielded a linear calibration curve in the concentration ranges of 1.5–200 μg/kg for carbofuran and 0.3–200 μg/kg for carbaryl with correlation coefficients (R ²) of above 0.9955. Limits of detection (S/N = 3) were 0.5 μg/kg for carbofuran and 0.1 μg/kg for carbaryl, respectively. The recoveries of this method ranged from 88.1 to 105.8%. The relative standard deviations were less than 8.1%.     

Thermal transition and thermo-physical properties of potato (<Emphasis Type="Italic">Solanum tuberosum L</Emphasis>.) var. Russet brown

Potatoes are an important food in many regions of the world and are commonly used in a variety of food products. Thermal transition and thermo-physical properties of potatoes are important in order to design efficient food processes and select appropriate storage conditions. In this study, we determined the thermal transitions and thermophysical properties of raw and blanched/par-fried potato for a temperature range of ??32 to 21.1 °C. Using differential scanning calorimetry, we found an initial freezing point (T_f) at ??1.8?±?0.1 °C, an onset of melting (T_m^′) at ??9.9?±?0.2 °C and an unfreezable water content (X^′_w) for maximally freeze-concentrated raw potato at 0.21 kg water/kg potato. Corresponding values for blanched/par-fried potatoes were ??0.9?±?0.1 °C, ??11.0?±?0.2 °C and 0.18 kg water/kg potato. Results show that an increase in solids content decreased T_f of both raw and blanched potatoes. We modelled the relationship between them using the Chen model. The apparent specific heat (C_app) increased around T_f to 31.7?±?1.13 kJ/kg K for raw potato and 26.7?±?0.62 kJ/kg K for blanched/par-fried potato. For frozen raw potato at ??32 °C, thermal diffusivity (α) was 0.89?±?0.01?×?10?^?6 m²/s and thermal conductivity (k), 1.82?±?0.14 W/m K, respectively. These values were higher for frozen raw potato than for the unfrozen raw potato (0.15?±?0.01?×?10?^?6 m²/s and 0.56?±?0.08 W/m K, respectively at 21.1 °C). The apparent density (ρ) of frozen raw potato (992?±?4.00 kg/m³ at ??32 °C) was less than that for unfrozen raw potato (1053?±?4.00 kg/m³ at 21.1 °C), and a similar trend was obtained for blanched/par-fried potato (993?±?2.00 kg/m³ at ??32 °C and 1188?±?7.00 kg/m³ at 21.1 °C, respectively). This study established a correlation between thermo-physical properties and temperature. Findings may be used to inform the design and optimization of freezing processes and frozen storage for potato products.     

A TLC-HPLC Method for Determination of Thiamphenicol in Pig,Chicken, and Fish Feedstuffs

An effective thin-layer chromatography (TLC) purification procedure coupled to high-performance liquid chromatography (HPLC) method was developed for the determination of thiamphenicol (TAP) in pig, chicken, and fish feedstuffs. The feedstuff samples were extracted with ethyl acetate, defatted with n-hexane saturated with acetonitrile, and further purified by TLC. The chromatographic separation was performed on a Waters Symmetry C₁₈ column using an isocratic procedure with acetonitrile-water (21.7:78.3, v/v) at 0.6 mL/min. The ultraviolet (UV) detector was set at a wavelength of 225 nm. The TAP concentrations in feedstuff samples were quantified using a standard curve. Good linear correlations (y?=?162,630x???2381.7, r?>?0.9998) were achieved within the concentration range of 0.05–10.00 μg/mL. The recoveries of TAP spiked at levels of 1, 10, and 100 μg/g ranged from 82.0 to 114.9% with the intra-day and inter-day relative standard deviation (RSD) less than 9.0%. The limit of detection (LOD) and limit of quantitation (LOQ) were 0.02 and 0.03 mg/kg for pig feedstuffs, 0.02 and 0.04 mg/kg for chicken feedstuffs, and 0.02 and 0.03 mg/kg for fish feedstuffs, respectively. This reliable, simple, and cost-effective method could be applied to the routine monitoring of TAP in animal feedstuffs.     

Determination of Eugenol in Aquatic Products by Dispersive Solid-Phase Extraction and Ultra-High-Performance Liquid Chromatography-Tandem Mass Spectrometry

A novel procedure, dispersive solid-phase extraction coupled with ultra-high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS), was developed for the determination of eugenol in aquatic products (shrimp, crab, and carp). Aquatic products were extracted with acetonitrile and primarily purified by dispersive solid-phase extraction with graphitized carbon black as absorbent. The pretreated acetonitrile extract was detected by UHPLC-MS/MS. UHPLC was carried out on Dikma Endeavorsil C₁₈ (30 mm × 2.1 mm, 1.8 μm) column eluted by methanol and water (80:20 v/v) at a rate of 0.30 mL min^?1. Tandem mass spectrometry was performed by electrospray ionization in negative ion mode to identify and quantify eugenol during multiple reaction monitoring. Under optimized analytical conditions, the matrix-matched spiked calibration sample demonstrates good linearity between 5.0 and 500.0 μg kg^?1 with a linear regression coefficient of 0.9996. The average recovery of eugenol from aquatic products is 95.3–103.4% at spiked levels between 5 and 50 μg kg^?1 with a relative standard deviation (n = 6) less than 5.4%. The limits of detection and quantification for eugenol were calculated to be 1.47 and 4.91 μg kg^?1, respectively. In comparison with those reported, the proposed method has advantages in low detection limit, high recovery, and short analysis time, meeting the requirements for the determination of trace eugenol residue in aquatic products.     

Application of Vacuum Frying as a Furan and Acrylamide Mitigation Technology in Potato Chips

Consumers like fried snacks, and taste, color, and texture are key aspects in their preference. However, during frying of foods some toxic compounds, such as furan and acrylamide, are produced. The objective of this work was to mitigate furan and acrylamide formation in potato chips, without affecting their main quality attributes, by using vacuum frying. To accomplish this purpose, potato slices were fried at atmospheric (P _abs 29.92 inHg) and vacuum conditions (P _abs 3.00 inHg), using equivalent thermal driving forces (T _{water boiling point} ? T _oil = 50, 60, or 70 °C). Furan and acrylamide concentration, oil content, and texture of both atmospheric and vacuum-fried samples were determined. Vacuum-fried potato chips showed reductions of about 81, 58, and 28% of furan, acrylamide, and oil content, respectively, when compared to their atmospheric counterparts. Additionally, the texture was not affected (p > 0.05) by changes in the pressure during frying. Results clearly showed that vacuum frying is an effective technology for furan and acrylamide mitigation in potato chips, since it reduces the content of both contaminants and preserves the quality attributes of fried snacks.     

Simultaneous Determination of Aflatoxin B1, Bisphenol A,and 4-Nonylphenol in Peanut Oils by Liquid-Liquid Extraction Combined with Solid-Phase Extraction and Ultra-High Performance Liquid Chromatography-Tandem Mass Spectrometry

An analytical method based on liquid-liquid extraction combined with solid-phase extraction and isotope dilution-ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) was well developed for simultaneous determination of aflatoxin B1 (AFB1), bisphenol A (BPA), and 4-nonylphenol (4-NP) in peanut oil. After adding isotope internal standards, the samples were firstly diluted by normal hexane and then extracted by acetonitrile and Carb/PSA solid-phase extraction cartridge in sequence to obtain the extracted solution. All the extracted solution was merged and was subsequently dried to near dryness by a mild nitrogen stream. Three target analytes were separated on a Phenomenex Luna C18 chromatographic column, quantified by an internal standard method and detected by ESI positive (ESI⁺) and negative (ESI^?) subsection acquisition modes under multi-reaction monitoring (MRM) conditions. Results demonstrated that the three target analytes exhibited excellent linearity in their corresponding concentration ranges of 0.1–100.0 μg/L with correlation coefficients all greater than 0.998. The corresponding method limits of quantitation (MLOQ, S/N?=?10) of AFB1, BPA, and 4-NP were 0.2, 1.0, and 2.0 μg/kg, respectively. Moreover, the mean recoveries for negative samples spiked at three concentration levels were calculated between 87.7 and 105.1% with relative standard deviation (RSD, n?=?6) ranging from 2.2 to 7.9% and the interday precision (n?=?5) ranging from 5.0 to 8.7%. Finally, the method was successfully applied to analyze 52 peanut oil samples, and AFB1 and 4-NP were detected in 43 samples with the concentrations in the ranges of 0.5–69.4 and 9.3–77.8 μg/kg, respectively. None of BPA was detected in any samples.     

Isotope Internal Standard Method for Determination of Four Acrylamide Compounds in Food Contact Paper Products and Food Simulants by Ultra-High Performance Liquid Chromatography Tandem Mass Spectrometry

A new method was developed for the determination of four acrylamide compounds (acrylamide, methacrylamide, N-methylol acrylamide, N-(Methoxymethyl)methacrylamide) in food contact paper products, three kinds of water-based food simulants, and dry food simulant (modified polyphenylene oxide, MPPO) by using ultra-high performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS). Acetonitrile was used as the extraction solvent for different kinds of samples. The extraction solution of paper products was purified with QuEChERS technology. Four analytes were separated by gradient elution in a UPLC HSS T3 column (100 mm?×?2.1 mm, 1.8 μm) with methanol and 0.1 % formic acid water as mobile phases, and then detected in electrospray ionization mode of MS/MS with multiple reaction monitoring (MRM). Under the optimal conditions, the calibration curves for four analytes were linear within the range of 1.0–200 μg/L and the correlation coefficients were higher than 0.998. The quantitation limits of the method (S/N?=?10) of four analytes were in the range of 0.3–20 μg/kg. The mean recoveries for five sample matrixes at three spiked concentration levels of 0.3–200 μg/kg were in the range of 81–108 % with the relative standard deviations (RSDs, n?=?6) values ranging from 2.5 to 7.1 %. The developed method is accurate, simple and rapid, which can be applied to the determination of acrylamide compounds in food contact paper products and food simulants.     

A New Two-Step Chromatographic Procedure for Fractionation of Potato Proteins with Potato Fruit Juice and Spray-Dried Protein as Source Materials

In an effort to purify potato proteins of superior food grade quality, a new procedure involving anion exchange (ion exchange (IEX)) and hydrophobic interaction chromatography (HIC) was established. Liquid potato fruit juice (PFJ) or re-suspended spray-dried protein was separated by IEX yielding two fractions: a protease inhibitor (PI)-rich fraction and a patatin-rich fraction. Each of these fractions was re-chromatographed on HIC, resulting in two new sub-fractions which were characterised by electrophoresis and mass spectrometry. A high-quality powder should have high lightness, low polyphenol oxidase (PPO) activity and glycoalkaloid content below 150 μg/g. The PI fraction from spray-dried powder had high lightness (L* = 83) compared to patatin (L* = 50), whereas IEX purification from PFJ resulted in a PI fraction with decreased lightness (L* = 66) and a patatin fraction with increased lightness (L* = 68). HIC fractionation led to increased lightness for patatin fraction, but decreased lightness for the PFJ PI fractions. HIC purification significantly lowered PPO activity in the fractions due to its selective affinity. The lowest total glycoalkaloid content was generally found in HIC fractions from spray-dried powder (150 μg/g), while high levels (>1000 μg/g) were found in PI fractions from PFJ. In conclusion, it was possible to obtain a PI-rich protein isolate from powder with good-quality attributes after both IEX and HIC, while for patatin, the best quality was obtained after the HIC only, and there, the colour or PPO activity may still be a problem depending on source material.     

Pressure-Thermal Kinetics of Furan Formation in Selected Fruit and Vegetable Juices

Furan, a potential carcinogenic compound, can be formed in array of processed foods. The objective of this study was to conduct kinetic studies in pineapple juice and assess the interactive effects of pressure (0.1 to 600 MPa) and temperature (30 to 120 °C) on furan formation. Additional experiments were carried out in tomato, watermelon, cantaloupe, kale, and carrot juice to understand the influence of matrix and juice pH. Furan was monitored in raw (control) and processed samples by automated headspace gas chromatography mass spectrometry, and quantified by calibration curve method with d₄-furan as internal standard. The data were modeled using zero-, first-, and second-order equations. The zero-order rate constants (k _T,P ), activation energy (E _a ), and Gibbs free energy of activation (ΔG ^?) of furan formation in thermally processed (TP; 90–120 °C) pineapple juice were found to be 0.036–0.55 μg/kg/min, 98–114 kJ/mol, and 173.9–180.5 kJ/mol, respectively. Furan concentration was negligible and close to the detection limit (0.37 μg/kg) after pressure treatment (600 MPa at 30 °C) of juice samples. For similar process temperatures, the rate constants of pressure-assisted thermally processed (PATP; 600 MPa at 105 °C) pineapple juice were lower than that of TP samples. Furan formation was influenced by juice matrix and pH. On the other hand, PATP markedly suppressed furan (0.7 to 1.6 μg/kg) in these selected juices. In conclusion, furan formation increased with process temperature and treatment time, while pressure treatment at ambient temperature did not promote its production. Furan formation in TP fruit juices was also influenced by juice matrix and pH, but these were not the significant factors for PATP-treated juices.     

Modified QuEChERS Combination with Magnetic Solid-Phase Extraction for the Determination of 16 Preservatives by Gas Chromatography–Mass Spectrometry

In this paper, based on the mechanism of the quick, easy, cheap, effective, rugged and safe (QuEChERS) method, a novel graphene grafted silica-coated Fe₃O₄ (Fe₃O₄@SiO₂@G) was synthesized and applied as the efficient magnetic solid-phase extraction (MSPE) adsorbent for rapid cleanup of vegetable samples prior to analyzing 16 preservative residues by gas chromatography–mass spectrometry (GC-MS). The method, which took advantages of the novel nanoparticle adsorbent and an external magnetic field separation targets from samples, not only could avoid the time consuming of the traditional solid-phase extraction, but also could be developed for simultaneous determination of 16 preservative residues in vegetables. Various experimental parameters that could affect the extraction efficiencies have been investigated. Under the optimum conditions, 16 preservatives showed good linearity over the range of 0.02–2.00 mg/L and correlation coefficients (R ²) of 0.9946–0.9998. The limits of detections (LODs) were in the range of 0.21–11.50 μg/kg. The recoveries of 16 preservatives ranged from 78.3 to 116.7 %, and the relative standard deviations (RSDs) ranged from 1.4 to 11.9 %.     

Verification of 5-Methyltetrahydrofolic Acid in Nutritional Products

A simple method for the verification of supplemental (6R,S)-5-methyl-5,6,7,8-tetrahydrofolic acid, “5-MTHF,” in nutritional products is described. Nutritional product samples are prepared for the liquid chromatographic/fluorescence detection (LC/FLD) determination of 5-MTHF by buffer dilution, 10-min centrifugation, and syringe filtration. Method performance has been defined by assessments of 5-MTHF linearity (r ² averaged 0.9999 ± 0.0001, and all relative calibration errors averaged ≤0.6%, for ten consecutive six-point standard curves), intermediate precision (rsd = 1.1%, n = 9, for three products fortified at ～1.73 μmol/kg = ～795 μg/kg, tested on each of 3 days), accuracy (spike recovery average = 92.8 ± 1.0%, n = 9, for nutritional products spiked with 5-MTHF at ～1.73 μmol/kg, or ～795 μg/kg), and selectivity (absence of interference from reagent blanks, and from four compounds structurally related to 5-MTHF). The 5-MTHF recovery, as % of unheated controls, from a simulated heat treatment (20 min at 120 °C) averaged 99.1 ± 0.6%, n = 4. The limits of 5-MTHF detection (S/N = 3) and quantification (S/N = 10) were experimentally determined to be 10 μg/kg (～0.020 μmol/kg) and 30 μg/kg (～0.060 μmol/kg), respectively (<10× the expected fortification rate). The method provides a simple and inexpensive means for verifying proper fortification, and for assessing the stability to processing and storage conditions, of free 5-MTHF in nutritional products. A finding of interest is the indication that liquid nutritional products may comprise a stable matrix for 5-MTHF fortification.     

Acrylamide in deep-fried snacks of India

Acrylamide content in deep-fried snacks from 20 different production sites of South Indian province of Kerala (80 samples representing 4 important product categories) were determined using a modified high performance liquid chromatography (HPLC)–diode array detector (DAD) method. The limit of detection and the limit of quantification for this method were 1.04 and 3.17 μg/kg, respectively. The mean recoveries of acrylamide obtained by using spiked samples ranged between 90% and 103%, which shows good extraction efficiency. Acrylamide concentrations in the four groups of snacks ranged from 82.0 to 4245.6 µg/kg for potato chips, 46.2–2431.4 µg/kg for jack chips, 24.8–1959.8 µg/kg for sweet plantain chips and 14.7–1690.5 µg/kg for plantain chips. These are the most widely consumed snacks in South India, and the results revealed reasonable levels of acrylamide in these foods, which indicated the general risk of consumer exposure.     

Determination of Trace Elements in Camellia Oil by Vortex-Assisted Extraction Followed by Inductively Coupled Plasma Mass Spectrometry

A simple vortex-assisted liquid–liquid extraction protocol followed by ICP-MS has been developed for the determination of nine elements (Cr, Mn, Fe, Ni, Cu, As, Zn, Cd, and Pb) in camellia oil samples. The key parameters affecting the extraction efficiency (extraction solvent characteristics, extraction time, and solvent/oil ratio) were carefully examined and optimized. Optimum results were obtained when 5 g of oil sample was used followed by vortex-assisted extraction for 20 min with 10 mL of 10 % HNO₃ (v/v). Detection limits ranging from 0.03 to 1 μg L^?1 and relative standard deviation lower than 6 % were obtained. The accuracy of the method was assessed by spiking experiments and comparison of the results from the extraction procedure with those obtained from microwave-assisted digestion of the samples. The recoveries were in the range of 84.3~102.3 %. No statistical differences, based on t test at a confidence level of 95 %, were detected. The proposed method was found to be simple, fast, and accurate when applied to camellia seed oil samples and has great potential in quantitatively detecting elements in various oils.     

Evaluation of a Selective Approach for the Determination of 5-Nitroimidazoles in Aquaculture Products by Capillary Liquid Chromatography Using Molecularly Imprinted Solid-Phase Extraction

Capillary liquid chromatography with UV detection is proposed for the determination of 5-nitroimidazole residues in aquaculture products. The separation was carried out in a C18 column at 20 °C, using a mobile phase consisting of water and acetonitrile, at 7 μL/min and 320 nm as detection wavelength. Furthermore, full loop injection mode (8 μL) was selected and water was considered as injection solvent. The optimized method was applied to the monitoring of nine 5-nitroimidazoles, including three metabolites, in crab, salmon, prawn, and velvet swimming crab. Molecularly imprinted solid-phase extraction has been evaluated for sample cleanup. The method was characterized in all the matrices in terms of linearity (R ² ≥ 0.9964), precision (repeatability, RSD ≤ 7.9%, and reproducibility, RSD ≤ 11.1%) and trueness (recoveries between 80.4 and 108.7%). Decision limits, CCα, ranging from 0.2 to 1.5 μg/kg and detection capabilities, CCβ, from 0.2 to 1.8 μg/kg, were obtained.     

An approach for extraction,purification, characterization and quantitation of acylated-anthocyanins from <Emphasis Type="Italic">Nitraria tangutorun</Emphasis> Bobr. fruit

In the present study, a systematic approach for extraction, purification and analysis of acylated-anthocyanins from Nitraria tangutorun Bobr. fruit was explored. Six acylated-anthocyanins in N. tangutorun fruit were identified by HPLC-MS/MS, and a rapid and efficient HPLC-DAD method was developed to analyze the acylated-anthocyanins. Ultrasonic-assisted extraction conditions of acylated-anthocyanins were optimized using response surface methodology, extraction at 70 °C for 32 min using 70% methanol solution (0.1% HCl, v/v) rendered an extract with 80.37?±?2.66 mg/100 g of cyanidin-3-O-(trans-p-coumaroyl)-diglucoside and 97.88?±?4.06 mg/100 g of total acylated-anthocyanins. Nine macroporous resins were investigated for preliminary purification of acylated-anthocyanins. According to the static/dynamic adsorption and desorption tests, XDA-6 macroporous resin exhibited the maximum potential for preparing acylated-anthocyanins. The purity of cyanidin-3-O-(trans-p-coumaroyl)-diglucoside (43.30 mg/g) in purified acylated-anthocyanins was 201.89 times of that of the extract (0.21 mg/g), and the purity of total acylated-anthocyanins increased from 0.36 to 56.44 mg/g. Besides, the stability (t _1/2) of cyanidin-3-O-(trans-p-coumaroyl)-diglucoside and total acylated-anthocyanins increased by more than five-fold after purification using XDA-6. The established methods of analysis, extraction and purification of acylated-anthocyanins were hopefully utilized in food industry.     

Optimization of Ultrasound-Assisted Extraction of Lycopene from Papaya Processing Waste by Response Surface Methodology

Lycopene possesses strong antioxidant ability, which may provide protection against cancer and other degenerative diseases. An ultrasound-assisted extraction method has been developed for the extraction of lycopene from papaya (Carica papaya L.) processing waste. Optimization conditions were firstly determined using single factor experiment, and then response surface methodology was used. Analysis showed that second-order polynomial models produced a satisfactory fitting of the experimental data with regard to lycopene (R ²?=?0.9147, P?<?0.001). The optimal conditions were 42.28 % ethanol in ethyl acetate as a solvent and extraction for 26.09 min at 50.12 °C. Under these conditions, the maximum yield of lycopene was 189.8?±?4.5 μg/g fresh weight (FW), which was higher than that obtained using the traditional extracting method (153.9?±?7.8 μg/g FW) and the Soxhlet extraction method (68.3?±?4.1 μg/g FW). The crude extract obtained could be used as either food additive or for further isolation and purification of lycopene. The results obtained are helpful for full utilization of papaya.     

A Powerful Analytical Strategy Based on QuEChERS-Dispersive Solid-Phase Extraction Combined with Ultrahigh Pressure Liquid Chromatography for Evaluating the Effect of Elicitors on Biosynthesis of <Emphasis Type="Italic">trans</Emphasis>-Resveratrol in Grapes

A powerful methodological approach based on modified quick, easy, cheap effective, rugged, and safe (QuEChERS) extraction technique, followed by cleanup dispersive solid-phase extraction (dSPE) and combined with ultrahigh pressure liquid chromatography (UHPLC), is presented in this paper, for the rapid determination of the health-promoting phytoalexin, trans-resveratrol, in grapes. This is the first time, to our knowledge, that the combination QuEChERS-dSPE/UHPLC-PDA has been used for trans-resveratrol quantification in grapes. The method has been validated according to European Union Decision 2002/657/EC, in terms of selectivity, linearity, sensitivity, instrument LOD and method LOQ, accuracy, precision, extraction efficiency, and interference assessment. Validation experiments revealed sufficient linearity (R ²?=?0.9931) within the established concentration range confirmed by Mandel’s fitting test. The sensitivity was good with method detection limit (LOD) of 0.003 μg/mL and quantification limit (LOQ) of 0.010 μg/mL. Optimum QuEChERS-dSPE/UHPLC-PDA conditions led to recoveries of the target analyte in grape samples ranging between 75.1 and 99.7 % and precisions in the 0.9–4 % range (RSD, n?=?18). The method also afforded satisfactory results in terms of extraction efficiency and interference assessment and provides a valuable and promising tool for determination of trans-resveratrol in grapes with a high resolution within 8 min and a total analysis time of 11 min. The validated methodology was applied to evaluate the effect of the use of elicitors, namely benzothiadiazole and methyl jasmonate, in trans-resveratrol biosynthesis on Vitis vinifera Monastrell grapes. The results obtained revealed an increase of trans-resveratrol level of 2-fold for grapes treated with benzothiadiazole and 3.5-fold for grapes treated with methyl jasmonate.