应用于特殊环境的光纤光栅温度压力传感器

目前,光纤光栅温度压力传感器在航空航天、土木工程、复合材料、石油化工等领域的应用非常广泛。由于其可以实现对温度、应变等物理量的直接测量,因此针对光纤光栅温度压力传感器的开发更多的集中于在特殊环境下的应用研究。本文以高温高压油井的特殊环境为例,对光纤光栅温度压力传感器进行了温度补偿式光纤光栅温度压力双参量传感系统的设计,并结合环境的特点进行了传感器相关器件的选择和调整。通过实验测试明确了该设计提高了光纤光栅温度压力传感器的适应性,完全能满足在特殊环境下的工作需求。     

光纤布拉格光栅压力传感技术与应用进展

光纤布拉格光栅（FBG）压力传感器具有水下无源、耐腐蚀、重量轻、成本低和抗电磁干扰等优点,应用广泛。文章简要介绍了FBG压力传感的基本原理,概述了FBG的写制技术、压力传感及增敏技术、温度补偿技术的发展现状,总结了近几年FBG压力传感器在海洋深度、湖泊液位测量、油气管道压力测量和岩土压力监测领域的应用进展,最后对FBG压力传感技术进行了展望。     

光纤光栅钎焊嵌入金属梁及传感性能研究

为了实现金属结构内部温度和应力实时监测,以SnAg共晶合金为钎料将光纤光栅钎焊嵌入了钢质简支梁。分析了嵌入金属梁的光纤光栅温度、压力传感特性;试验监测了简支梁温度、压力与光纤光栅中心波长变化。结果表明,嵌入的光纤光栅中心波长和温度变化与梁所受压力大小都成线性关系,温度传感灵敏度比裸光栅提高了约一倍。     

多点光纤光栅测温系统在渗流监测中的应用研究

为了监测土石坝内的渗流水的情况,提出一种多点光纤Bragg 光栅传感器(FBG)的结构,采用InGaAs光电探测器阵列探测光强的光纤光栅传感阵列的波长解调方法。根据室内实验结果,对多点光纤光栅传感系统的可行性和监测数据的可靠性进行分析, 给出用于坝体温度场监测的光纤光栅传感器波长温度响应灵敏度可达到0.0091nm/℃。工程中采用电热脉冲方式对传感器附近小范围的土壤进行加热,使其与水的温度形成一定的温差,实测结果表明可以利用光纤光栅传感器监测温度异常的方法判断是否发生渗流, 从而实现对坝体内集中渗漏点的定位和自动监测。在系统防雷击、抗干扰性方面, 采用光纤光栅传感监测系统与传统仪器相比具有明显优势。     

采用掩模板制作的光纤布喇格光栅传感器

光纤布喇格光栅(FBG)是国际上光纤传感技术研究的前沿热点。在恶劣环境下对复杂结构进行变形和健康监测，具有波长编码等明显的其他传感器所没有的特点。将由光纤光栅组成的阵列埋入结构材料内部，可用来监测桥梁、大坝、重要建筑物以及船体、航天器内部的温度、应变、压力及材料结构状态的变化。该文介绍了采用掩模板制作光纤光栅传感器的原理和方法，分析了采用相位掩模法制作的分布式光纤布喇格光栅传感器的灵敏度等测量性能和噪声的随机过程特性，从而为其在船舶结构变形测量技术中的应用提供了科学依据。     

长周期光纤光栅传感器的研究进展

分析了长周期光纤光栅传感器的工作原理,介绍了目前长周期光纤光栅在温度传感、应力传感、折射率传感、弯曲量传感、扭曲量传感以及电流传感等方面的应用。     

光纤光栅原油压力传感器实验及其可靠性研究

介绍并制作了一种光纤光栅高温高压传感器,它由三种金属管组成,中央的弹性金属管将液体的压力转换为管子的机械伸长,周围金属管的长度只随温度变化。光纤光栅的两端分别固定在中央管及周围管的末端,随着压力管内液体压力的增加,光栅的中心波长随之增加,实现了对液压的传感。对该传感器的温度补偿进行了分析,设计了具有相同温度系数的压力传感光栅与温度传感光栅。并对传感器进行了高压实验和高温、高湿存储实验。结果表明,这种压力传感器在0~50 MPa之间灵敏度为31.7 pm/MPa。经过200℃高温存储16 h,及100℃沸水浸泡6 h,波长没有观察到明显衰退现象。     

石油测井光纤光栅温度压力传感器

根据石油测井时对温度、压力传感器的要求,设计了一种利用聚合物封装的光纤布喇格光栅(FBG)传感器.封装后的光纤光栅温度和压力灵敏度系数分别为0.02128 nm/℃和0.163 nm/MPa,分别为裸光栅的2.1倍和52.3倍,压力测量范围0～30 MPa,且传感器的温度和压力响应与光栅反射波长呈良好的线性关系.通过现场测井实验,测得光纤光栅温度和压力传感器与电子五参数传感器的测量值符合良好,该传感系统满足了温度和压力测量的要求.     

卫星镜头结构光纤光栅温度传感器研究

为了解决卫星星敏感器光学镜头结构在轨温度监测问题,提出一种弧形基底封装的光纤光栅温度传感器。分析了星敏镜头结构特征与光纤光栅温度传感原理,采用飞秒激光刻写的光纤光栅作为敏感元件,设计了可贴合于星敏镜头结构特征的弧形封装基底,完成了光纤光栅温度传感器封装,并对传感器进行了拉伸测试、温度标定及温度重复性测试,并已应用于实际工程中。结果表明:弧形封装结构形式的光纤光栅温度传感器线性度可达0.998,温度灵敏度达到8.54 pm/℃,同一温度下中心波长变化量在2 pm以内,且受弧形基底封装结构变形产生的应变影响小。卫星在轨温度监测,光纤光栅传感与电子式传感相差±3 ℃。可以实现星敏镜头结构的温度测量功能,在星敏感器结构在轨温度测温中具有应用前景。     

光纤光栅传感网络的优化研究

光纤光栅传感网络在大型复杂结构健康监测中具有广泛的应用前景,对光纤光栅传感网络优化的研究具有重要的意义。分析了结构健康监测中光纤传感网络优化布局和可靠性的研究现状,对光纤传感网络优化中的传感器优化布局与光纤传感网络可靠性两方面进行研究。通过对结构响应特性研究,提出了对结构静力响应参数监测时,传感器布局的一般规则。将概率计算引入光纤 FBG 传感网络不同拓扑结构,给出了基于不同拓扑结构的光纤传感网络形式及其可靠性数值分析。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks