共查询到20条相似文献,搜索用时 15 毫秒
1.
The self-step growth polymerization of RAf monomers in homogeneous, continuous flow stirred tank reactors (HCSTRs) is simulated under conditions of periodic feed concentration (with frequency ω and amplitude α). By having periodic operation, the polydispersity index of the polymer is found to increase by about 35% over the values at steady state. Periodic operation of HCSTRs is found to lead to gelation only for certain values of the frequency and the dimensionless residence time τ*. Gelling envelopes have been obtained to give conditions under which HCSTRs should be operated. These envelopes can be described in terms of two critical dimensionless residence times, τ and τ such that nongelling operation is always ensured when τ* < τ. For τ* > τ, periodic operation always leads to gelation, and HCSTRs cannot be used. For τ < τ* < τ, the gelling behavior is found to depend on the functionality f, amplitude α, and the dimensionless residence time τ*. 相似文献
2.
V. I. Dakin 《应用聚合物科学杂志》1996,60(7):999-1003
The computed dependencies of elastic characteristics of branched-network polymers were obtained on the basis of the Takayanagi series model. The moduli ratio (λ) for branched-network and branched polymers increases as a result of an increase of the moduli ratio of network and branched phases (E/E) and the network phase fraction (Vnet). The λ-increase as a function of Vnet is larger than in the case of the E/E dependence. On the basis of computed dependencies, the experimental results for the radiation crosslinked SBS block copolymer were considered. The experimental results agree with the computed de-pendencies for the hetergeneous branched-network polymers with E/E ≈︁ 20. The influence of entanglements on the elastic characteristics of branched-network polymers is discussed. © 1996 John Wiley & Sons, Inc. 相似文献
3.
Dynamic adsorption behaviors between Cr(VI) ion and water‐insoluble amphoteric starches was investigated. It was found that the HCrO ion predominates over the initial pH ∼ 2–4, the CrO ion predominates over the initial pH ∼ 10–12, and both ions coexist over the initial pH ∼ 6–8. The sorption process occurs in two stages: the external mass transport process occurs in the early stage and the intraparticle diffusion process occurs in the long‐term stage. The diffusion coefficient of the early stage (D1) is larger than that of the long‐term stage (D2) for the initial pH 4 and pH 10. The diffusion rate of HCrO ion is faster than that of CrO ion for both processes. The D1 and D2 values are ∼ 1.38 × 10−7–10.1 × 10−7 and ∼ 0.41 × 10−7–1.60 × 10−7 cm2 s−1, respectively. The ion diffusion rate in both processes is concentration dependent and decreases with increasing initial concentration. The diffusion rate of HCrO ion is more concentration dependent than that of CrO ion for the external mass transport process. In the intraparticle diffusion process, the concentration dependence of the diffusion rate of HCrO and CrO ions is about the same. The external mass transport and intraparticle diffusion processes are endothermic and exothermic, respectively, for the initial pH 4 and pH 10. The kd values of the external mass transport and intraparticle diffusion processes are ∼ 15.20–30.45 and ∼ −3.53 to −12.67 kJ mol−1, respectively. The diffusion rate of HCrO ion is more temperature dependent than that of CrO ion for both processes. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2409–2418, 1999 相似文献
4.
Ivan imkovic Miroslav Antal Vincent Mihlov Jozef Knigstein M. M. Micko 《应用聚合物科学杂志》1985,30(12):4707-4711
Trimethylammoniumhydroxypropyl (TMAHP)–cellulose in 10 anionic forms (F?, Cl?, Br?, I?, HSO, NO, OH?, HCO, H2PO, CH3COO?) was prepared, and the influence of each anion on thermal degradation in inert atmosphere was studied. With the help of dynamic and isothermal thermogravimetry (TG) it was found that H2PO ions had the greatest retarding effect on TMAHP–cellulose degradation. From the values of rate constants it can be seen that all ionic forms of TMAHP–cellulose have the starting rate of thermal degradation greater than unmodified cellulose. The calculated values of activation energy of thermal degradation for different ionic forms are decreasing in following sequence: H2PO > F? > NO > I? > Br? > HCO > Cl? > HSO > OH? > unmodified cellulose > CH3COO?. From the results of pyrolyse measurements in combination with gas chromatography and mass spectrometry (Py–GC–MS) it follows that the products of the elimination of quarternary ammonium salts are trimethylamine, 3-hydroxy-2-propanone, and, in the case of OH? form, water. In all other ionic forms the third product is the corresponding acid. 相似文献
5.
Vinyl chloride–diallyl phthalate (VC–DAP) suspension copolymerization was carried out in a 5‐L autoclave and 200‐mL stainless steel vessel at 45°C. The apparent reactivity ratios of VC–DAP suspension copolymerization system were calculated as rVC = 0.77 and rDAP = 0.37. It shows that VC–DAP copolymer contains no gel when the feed concentration of DAP (f) is lower than a critical concentration (fcr, inside the range of 0.466–0.493 mmol/mol VC at 80–85% conversion), the polymerization degree (DP) of copolymer increases with the increase of f and conversion. VC–DAP copolymer is composed of gel and sol fractions when f is larger than fcr. The DP of sol fraction decreases as f increases, but the gel content and the crosslinking density of gel increase. The gel content also increases as conversion increases. The results also show that the index of polydispersity of molecular weight of sol changes with f, a maximum value appears when f is close to fcr. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 156–162, 2000 相似文献
6.
Some new cellulosic materials, suitable for the adsorption of noble metal ions, were syn-thesized by chemical and electrochemical modification of cellulose. The polymerizable groups were introduced in cellulose with ∼ 80% yield of substitution by esterification with acryloyl chloride. The vinyl monomers (4-vinylpyridine, 1-vinylimidazole, 1-vinyl-2-pyrrolidinone, and 9-vinylcarbazole) were readily grafted into cellulose acrylate via radical polymerization in acetonitrile. The grafted copolymers of cellulose with 4-vinylpyridine and 4-vinylimidazole were reacted with methyl iodide and the corresponding 1-methylpyridinium iodide ( 6 ) and 3-methylimidazolium iodide ( 7 ) copolymers of cellulose were obtained. Copolymers 6 and 7 were transformed into new polymeric regents, differing in anions (ClO, CF3COO−, NO, p-TsO−, BF, PF) by using a supporting electrolyte carrying the desired anions through the ion-exchange-electrochemical oxidation of the released iodide at a controlled anodic potential. © 1996 John Wiley & Sons, Inc. 相似文献
7.
The air separation through triheptyl cellulose (THC)/ethyl cellulose (EC) blend membranes containing no more than 20 wt % THC at the temperature range from 298 to 358 K was investigated using a variable volume method. The air-separation ability for the THC/EC membranes were greater than that for the THC-free pure EC membrane. P for the THC/EC membranes was between 1.06–8.89 × 10?9 cm3 (STP) cm/cm2 s cmHg and P/P 3.04–3.66. The THC/EC membrane showed a unique trend in its P/P ? P relationship, i.e., the magnitude of P/P increased simultaneously with that of P. The THC/EC membrane yielded a maximum oxygen concentration in the oxygen-enriched air (OEA) of 39.5% at an OEA flux of 6.99 × 10?4 cm3 (STP)/s cm2 for a pressure difference of 0.43 MPa at 358 K. After 300 h of measurement at 0.40 MPa and 313 K, the efficiency of the concentrating oxygen was almost constant. © 1994 John Wiley & Sons, Inc. 相似文献
8.
Toshiaki Matsunaga 《应用聚合物科学杂志》1977,21(10):2847-2854
The dispersion force component of surface free energy, γ, and the nondispersive interaction free energy between solid and water, I, were determined by the two-liquid contact-angle method, i.e., by the measurement of contact angles of water drops on plain solids in hydrocarbon, for commercialy available organic polymers such as nylons, halogenated vinyl polymers, polyesters, etc. A method to estimate the I values from the knowledge of the polymer composition is also proposed, on the basis of the assumption of the spherical monomer unit and the sum of interactions between functional groups and water molecules at the surface. 相似文献
9.
Ana Regina Feitosa De Britto Maria Irismar N. Ximenes Glaucione Gomes De Barros 《应用聚合物科学杂志》1996,60(11):1793-1802
The morphology of low-density polyethylene (LDPE) modified by in situ sorption and thermal polymerization of acrylic acid (AA) in the matrix was examined. The microstructure of the LDPE/poly(acrylic acid) (PAA) materials after Eu3+ and UO ion exchange was investigated. The phase behavior of these materials was analyzed using X-ray diffraction, scanning electron microscopy (SEM), and thermal measurements (DSC). The X-ray dif-fraction studies showed that PAA is located at amorphous region of the matrix. The LDPE/PAA surface, as investigate by SEM, was apparently homogeneous before and after Eu3+ and UO ion exchange, respectively. Two Tg values were found for the LDPE/PAA material before and after Eu3+ ion exchange. Also, three and four Tg values were found for LDPE/PAA after UO ion exchange depending on the amount of UO in the modified matrix. This indicates microphase domains in the LPDE/PAA-, LPDE/PAA/Eu3+-, and LPDE/PAA/UO -modified materials, although a lack of visible phase separation in the micrographs was observed. © 1996 John Wiley & Sons, Inc. 相似文献
10.
Poly(N‐vinyl 2‐pyrrolidone) (PVP)/acrylonitrile (AN) interpenetrating polymer networks (IPNs) were synthesized and amidoximated for the purpose of uranyl ion adsorption. The adsorption of amidoximated IPNs was studied from different uranyl ion solutions (850, 1000, 1200, 1400, and 1600 ppm). The result of all our adsorption studies showed that the bonding between UO‐amidoxime groups complied with the Langmuir‐type isotherm. The adsorption capacity was found as 0.75 g UO/g dry amidoximated IPN. In order to increase the UO ion adsorption capacity the amidoximated IPN was treated with alkali, but no significant increase could be observed. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2324–2329, 2001 相似文献
11.
Poly(3‐methylthiophene) (P3‐MeT) doped with different anions were prepared electrochemically in the presence of tetraalkylammonium salts. The new poly(3‐methylthiophene) SnCl and SbCl (P3‐MeT SnCl5 and P3‐MeT SbCl6) were prepared electrochemically using tetra‐n‐butylammonium pentachlorostannate and tetra‐n‐butylammonium hexachloroantimonate as the supporting electrolytes. The effect of current density, salt concentration, reaction temperature, and the nature of solvents on the polymer yield and polymer conductivities have been investigated. Cyclic voltammetry of poly(3‐methylthiophene) has been examined at platinum electrode in 1,2‐dichloroethane medium containing n‐Bu4NSnCl5, Bu4NSbCl6, and Bu4NClO4 as the supporting electrolytes in the range of −1.0 to 1.7 V versus SCE in the presence and absence of 3‐methylthiophene. Electrical conductivity, magnetic susceptibility measurements, and structural determination by elemental analysis and infrared studies were also made. Scanning electron microscopy revealed a globular, branched, fibrous and a spongy, fibrous morphology of poly(3‐methylthiophene) SnCl, ClO, and SbCl, respectively. The thermal analysis of the polymers was also investigated. Possible causes for the observed lower conductivity of these polymers have also been discussed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 91–102, 1999 相似文献
12.
Norio Tsubokawa 《应用聚合物科学杂志》1985,30(5):2041-2049
It was found that the cationic ring-opening polymerization of δ-valerolactone (VL), ε-caprolactone (CL), and β-propiolactone (PL) was initiated by carbon black containing CO+ClO groups, which were introduced by the reaction of COCl groups with AgClO4. The polyester was propagated from CO+ClO groups and effectively grafted onto carbon black surface. The polymerizability of these lactones by CO+ClO groups decreased in the following order: VL > CL > PL. The increasing temperature of the polymerization caused an increase in the rate of the chain transfer reaction of the growing chains and brought about the decrease of grafting ratio of polyester onto carbon black. 相似文献
13.
Mean permeability coefficients for CH4 and CO2 (P̄ and P̄) in cellulose acetate (CA, DS = 2.45) were determined at 35°C (95°F) and at pressures up to about 54 atm (800 psia). The measurements were made with pure CH4 and CO2 as well as with CH4/CO2 mixtures containing 9.7, 24.0, and 46.1 mol % CO2. In the measurements with the pure gases, P̄ was found to decrease with increasing pressure, as expected from the “dual-mode” sorption model. By contrast, P̄ passes through a minimum and then increases with increasing pressure, probably due to the plasticization (swelling) of CA by CO2. The values of P̄ and P̄ determined with the mixtures containing 9.7 and 24.0 mol % CO2 decrease with increasing total pressure; this behavior is adequately described by the extended “dual-mode” sorption model for mixtures. By contrast, the values of P̄ and P̄ obtained with the mixture containing 46.1 mol % CO2 pass through a minimum and then increase as the total pressure is raised, probably also due to the plasticization of CA by CO2. The CO2/CH4 selectivity (≡P̄/P̄) of the CA membrances decreases with increasing total pressure and, at constant pressure, decreases with increasing CO2 concentration in the feed mixture. The effects of exposing the CA membranes to high-pressure CO2 prior to the permeability measurements (“conditioning” effects) on P̄ and P̄ have also been studied. © 1996 John Wiley & Sons, Inc. 相似文献
14.
The thermal stability of the heterogeneous nucleation effect of polypropylene (PP) nucleated with an organic phosphate (A) and two kinds of sorbitol derivatives (B and D) was investigated by DSC multiscanning. For pure PP, the peak temperature of crystallization (T) was little changed with an increasing number of DSC scans, indicating that nucleation of PP is thermally stable. For the PP nucleated with an organic phosphate (PPA), the temperatures at the onset of crystallization (T) and at the completion of crystallization (T); the peak temperature of crystallization (T) and melting (T); and the heat of crystallization (ΔHc) and fusion (ΔHm) of PP are higher than those of pure PP and were little influenced with an increasing number of DSC scans. For PP nucleated with the sorbitol derivatives (PPB and PPD), the T, T, T, and T decreased with an increasing the number of scans. These results indicated that the thermal stability of heterogeneous nucleation effect of the nucleating agent A is higher than that of nucleating agents B and D. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1643–1650, 2002 相似文献
15.
Surface fluorination of poly(trimethylsilylpropyne) (PTMSP) membranes by CF4 plasma was studied. The surface fluorination of the membranes was carried out in an atmosphere of CF4 in a capacitively coupled discharge apparatus with external electrodes. Dramatic increase in selectivity (P/P) was observed. The effect of fluorination conditions such as duration of treatment and discharge power on the permeabilities of the membranes was studied. X-ray photoelectron spectrometric data of modified PTMSP membranes showed a drastic alternation in the surface layer. The P and P/P of the membranes were observed to be dependent on the F/C atomic ratio. At F/C > 1, the P/P value of the membranes could be more than four. © 1993 John Wiley & Sons, Inc. 相似文献
16.
The viscoelastic properties of a rubber–resin blend, which influences performance of the blend as a pressure-sensitive adhesive, depend upon the structure of the resin as well as its molecular weight. The effect of the concentration of a compatible resin in the blend was examined using a mechanical spectrometer. Four types of resins were used. These are the rosin esters, polyterpenes, pure monomer resins such as polystyrene and poly(vinyl cyclohexane), and petroleum stream resins. Each was examined in blends with both natural rubber and styrene–butadiene rubber over a range of concentrations. It is shown that the temperature of the tan δ peak for compatible systems can be predicted by the Fox equation, T = W1T + W2T, where W1 and W2 are the weight fractions of the resin and rubber, respectively, and the Tg's are the tan δ peak temperatures in K. The plateau modulus G for a blend can be identified as the G′ value in the rubbery plateau at the point where tan δ is at a minimum. The relationship between G and G, the plateau modulus for the undiluted elastomer, is shown to be proportional to the volume fraction of the elastomer raised to the 2.3–2.4 power for natural rubber with six different compatible resins. The exponent for styrene–butadiene rubber is 2.5–2.6 with four different resins. Using these relationships, both the tan δ peak temperature and plateau modulus can be predicted for a rubber–resin system from data on the unmodified elastomer and on one typical rubber–resin blend. 相似文献
17.
Uniaxially and biaxially oriented polystyrene films were prepared in a biaxial stretching machine. The state of orientation was determined by birefringence measurements and represented in terms of a set of biaxial orientation factors ?. The data are plotted on an isosceles triangular diagram whose coordinates represent the orientation factors ?, ?. Tensile force–elongation curves were obtained on the films in the machine stretching direction (MSD) and at various angles to the MSD in the plane of the film. The isotropic film is brittle, while uniaxial films yield in the machine direction but are brittle in the transverse direction. The biaxially oriented films exhibit ductile yielding in all directions in the plane of the film. 相似文献
18.
A calorimetric study for estimating crosslinking densities of polydimethylsiloxane (PDMS) networks is presented. It involves the experimental determination of the heat capacities of the polymer with (C) and without (C) crosslinking. The theoretical basis of the method is described as well as the procedure used for the determination of the Cps. The crosslinking densities of PDMS networks, determined by absorbency (swelling) measurments, using the Flory-Rehner equation, and by the method described here, are compared. The PDMS, obtained by the anionic synthesis of octamethylcyclotetrasiloxane, was analyzed by gel permeation chromatography and infrared spectroscopy. Separate samples of the polymer were further crosslinked at different network densities. The Cps and the thermal stabilities were determined by DSC and TGA, respectively. The results indicate that the crosslinking density ratios of the polymer networks calculated by the relation ΔC/C are in reasonable agreement with those obtained from absorbency measurements. The crosslinking density can also be obtained from heat capacity measurments if the density of the network is known at the temperature that ΔCp is obtained. © 1995 John Wiley & Sons, Inc. 相似文献
19.
With the help of DTA, DTG elementary analysis of carbonized residues and ESR spectroscopy the influence of anionic form on thermooxidation of trimethylammoniumhydroxyprophyl (TMAHP)–cellulose was studied. At 300°C the percentage of carbon in carbonized residue thermolyzed in oxidative atmosphere is higher than for the sample degraded in inert atmosphere. The percentage of hydrogen decreases simultaneously. The concentration of free radicals in thermolyzed residue also increases due to the presence of oxygen. We propose that oxygen is abstracting the hydrogen atoms from polysaccharide and unpaired electrons on carbon atoms are produced. At 400°C the percentage of carbon in residues prepared at inert atmosphere is higher than for residue formed at oxidative atmosphere. Also the concentration of free radicals in thermolyzed residues obtained in inert atmosphere is greater than for those from oxidative ones. That is why suppose that at this temperature oxygen is bonded to polysaccharide residue and free radicals are terminated. From the semiquantitative DTA we can make the following sequence of samples according to their increasing thermooxidative effect: unmodified cellulose < A–HSO < A–Br? < A–I? < A–NO < A–H2PO < A–CH3COO? < A–HCO < A–F? < A–Cl?1 < A–OHp?. 相似文献
20.
Ligia Gargallo Deodato Radić Nasrollah Hamidi Leonidas Cardenas Arturo Horta Irmina Hernandez-Fuentes 《应用聚合物科学杂志》1988,36(6):1495-1500
Partial specific volumes ν of a series of poly(o-alkyl phenyl methacrylate)s and polydiitaconates were determined by density measurements, in toluene and tetrahydrofuran solutions, respectively. The effect of the size and nature of the side groups on partial specific volume is analyzed. Good agreement is found between the experimental ν values and those obtained theoretically from the group contribution method. 相似文献