Al2O歧化法制备微细Al2O3/Al复合粉体

真空条件下,以Al2O3和Al为原料,通过Al2O歧化法制备微细Al2O3/Al复合粉体.XRD和SEM分析表明:在反应温度为1200～1400℃时,随着温度的升高,粉体中氧化铝含量升高;冷凝温度约为550～750℃时,复合粉体中的氧化铝包括稳定晶型和不稳定晶型;冷凝温度约为1100～1300℃时,复合粉体中的氧化铝全部为稳定晶型;冷凝温度约为550～650℃时,复合粉体的平均粒径小于0.5μm;冷凝温度约为750℃时,铝熔化、微粒团聚;冷凝温度约为1100～1200℃时,铝形成铝珠,氧化铝为不规则状、平均粒径小于2μm;冷凝温度约为1300℃时,氧化铝为片状.因此,通过选取合适的反应温度、冷凝温度,可以控制Al2O3/Al复合粉体中氧化铝的含量、晶型和粒径.     

Air plasma-sprayed Y2O3 coatings for Al2O3/Al2O3 ceramic matrix composites

Al₂O₃/Al₂O₃ ceramic matrix composites (CMC) are candidate materials for hot-gas leading components of gas turbines. Since Al₂O₃/Al₂O₃ CMC are prone to hot-corrosion in combustion environments, the development of environmental barrier coatings (EBC) is mandatory. Owing to its favorable chemical stability and thermal properties, Y₂O₃ is considered a candidate EBC material for Al₂O₃/Al₂O₃ CMC. Up to 1 mm thick Y₂O₃ coatings were deposited by means of air plasma spraying (APS) on Al₂O₃/Al₂O₃ CMC with a reaction-bonded Al₂O₃ bond-coat (RBAO). APS Y₂O₃ coatings exhibit a good adherence in the as-deposited state as well as upon isothermal annealing up to 1400 °C. Moreover, furnace cyclic testing performed at 1200 °C revealed an excellent durability. This is explained by the formation of a continuous, approximately 1 μm thick reaction zone at the APS Y₂O₃/RBAO interface. The reaction zone between Y₂O₃ and Al₂O₃ comprises three layers of thermodynamically stable yttrium-aluminates exhibiting strong bonding, respectively.     

Ruby micro-piezospectroscopy in GdAlO3/Al2O3(/ZrO2), Er3Al5O12/Al2O3(/ZrO2) and Y3Al5O12/Al2O3(/ZrO2) binary and ternary directionally solidified eutectics

The fluorescence from (naturally present) Cr³⁺ impurities was used to measure the residual stress in the alumina phase of six melt-grown ceramic eutectic composites associating gadolinum aluminum perovskite (GAP), erbium aluminum garnet (EAG) or yttrium aluminum garnet (YAG) with α-alumina and cubic zirconia. Such measurements are reported for the first time in the GAP containing eutectics.In the usual hydrostatic assumption, we conclude to a residual compression in the range of ～70–400 MPa depending on the sample composition. The validity of the hydrostatic assumption is questioned when a microscope is used for the measurements.     

Al2O3/Al2O3扩散连接机理的研究

采用热压方式进行氧化铝陶瓷材料的扩散连接，并深入探讨了其连接机理，结果表明：采用适当的连接工艺，可使此种材料产生塑性形变，接触面积增加，空洞收缩和闭合，扩散进行充分，1420℃，15MPa热压60min条件下，获得的最高强度为357MPa，超过母材强度平均连接强度为250MPa，是母材平均强度的85％。     

Mechanisms of hydrodenitrogenation of alkylamines and hydrodesulfurization of alkanethiols on NiMo/Al2O3, CoMo/Al2O3, and Mo/Al2O3

The simultaneous hydrodenitrogenation (HDN) of alkylamines and hydrodesulfurization (HDS) of alkanethiols, with the NH₂ and SH groups attached to primary, secondary, and tertiary carbon atoms, were studied at 270–320 °C and 3 MPa over sulfided NiMo/Al₂O₃, CoMo/Al₂O₃, and Mo/Al₂O₃ catalysts. Pentylamine and 2-hexylamine reacted by substitution with H₂S to form alkanethiols and with another amine molecule to form dialkylamines. Alkenes and alkanes were not formed directly from pentylamine and 2-hexylamine, but indirectly by elimination and hydrogenolysis of the alkanethiol intermediates, as confirmed by their secondary behavior and the similar alkene/alkane ratios in the simultaneous reactions of amines and thiols. Only 2-methyl-2-butylamine, with the NH₂ group attached to a tertiary carbon atom, produced alkenes as primary products by E1 elimination. NiMo/Al₂O₃ and CoMo/Al₂O₃ have a higher activity for the HDS of alkanethiols than does Mo/Al₂O₃; H₂S has a negative influence. This shows that the thiols react on vacancies on the catalyst surface (Lewis acid sites). Mo/Al₂O₃ is the best HDN catalyst; H₂S has a positive influence on the HDN of amines with the NH₂ group attached to a secondary and a tertiary carbon atom. This indicates that the HDN of alkylamines occurs on Brønsted acid sites.     

Ethylene Hydrogenation over Pt/Ga2O3/Al2O3 Catalysts

The effects of gallia addition on the Pt dispersion and the activity for ethylene hydrogenation at 0 °C were studied for Pt-supported catalysts as a function of the reduction temperature (350, 450, and 550 °C). The catalysts contained 0.5 wt.% Pt and were prepared by successive incipient wetness impregnations with Ga(NO₃)₃ and H₂PtCl₆ aqueous solutions. CO and H₂ chemisorption data indicated that, the addition of small amount of Ga₂O₃ caused an increase of the Pt dispersion and a decrease of ethylene conversion. Both of them decreased appreciably when Ga₂O₃ addition was increased, particularly, for the case where β-Ga₂O₃ was used as a support. The increase in reduction temperature magnified the negative effects of the gallia addition on dispersion and activity, although the addition of small amount of gallia improved the resistance to metal sintering. Results were interpreted in terms of the presence of reduced Ga species, which can encapsulate Pt particles.     

Ni/Al_2O_3覆膜方法

阐述了Ni/Al2 O3 复合颗粒在生产中的应用 ,讨论了在Al2 O3 陶瓷颗粒上形成Ni膜的三种方法 ,分析了这些方法的优缺点。     

Propylene metathesis over Re2O7/Al2O3-B2O3 catalysts

A series of alumina aluminum borate (AAB) with various Al/B molar ratios were prepared by the coprecipitation method. The supported rhenium oxide catalysts with various contents of Re₂O₇ were also prepared by the impregnation method with perrhenic acid. The catalytic activity and stability of Re₂O₇/AAB catalysts for the reaction of propylene metathesis were tested in a fixed-bed microreactor. It was found that Re₂O₇/AAB is more active, stable and regenerable than Re₂O₇/Al₂O₃ for propylene metathesis. The optimum Al/B molar ratio was found to be in the range of 4–10.     

氧化铝载体对镍/氧化铝催化剂性能的影响

氧化铝是化工催化行业广泛应用的催化剂载体。油脂加氢催化剂主要是以氧化铝为载体、镍为主要活性组分的催化剂。在制备镍/氧化铝催化剂的过程中,载体氧化铝使用的最佳条件：载体在共沉淀反应前加入,载体氧化铝比表面积为340.6 m2/g,载体氧化铝加入量为m（镍）∶m（氧化铝）=5∶4,反应的老化时间为45 min。在此条件下,制备的镍/氧化铝催化剂活性最高,应用效果最好。     

High-temperature mechanical property and thermal shock resistance of Al2O3f/Al2O3 composites

Continuous alumina fiber–reinforced alumina matrix composites (Al₂O_3f/Al₂O₃ composites) were produced via sol–gel process, then the high-temperature mechanical property and thermal shock resistance of Al₂O_3f/Al₂O₃ composites were investigated. The results showed that the composites exhibited excellent high-temperature properties. The mechanical property of the composites was affected by heat treatment (prepared at 1100°C exhibited the most desirable mechanical property). The tensile strength of the composites abruptly decreased at higher temperatures. Although the mechanical property of the composites deteriorated after the thermal shock test was conducted at high temperatures, they exhibited excellent thermal shock resistance. After 50 thermal shock tests conducted at 1300 and 1500°C, the flexural strength of the composites was found to be 124.34 and 93.04 MPa, thus showing a decrease in strength with the increasing temperature.     

Al2O3/Fe3Al复合材料的制备及性能

利用热压烧结制备了致密的Al_2O_3/Fe_3Al复合材料。测试表明,该复合材料具有良好的力学性能,其抗弯强度和断裂韧性的最大值分别为832 MPa和7.96 MPa·m~1/2。对试样进行压痕实验,采用SEM对裂纹扩展方式进行观察,结果表明,在复合材料中存在着多种增韧机制,裂纹表现出复杂的扩展方式,这将在较大程度上吸收裂纹扩展能,从而使复合材料的断裂韧性得以提高。     

负载型纳米FeOZrO2/Al2O3催化剂的制备

主要研究制备以大孔A12O3,为基载体的负载型纳米FeOZrO2/Al2O3,复合载体.采用溶胶-凝胶法制备负载型纳米FeOZrO2/Al2O3,复合载体.利用比表面、透射电子显微镜(TEM)等对载体催化剂进行了表征.结果表明:负载型纳米FeOZrOJhl203复合载体的比表面积达到76.53 sq·m/g,FeOZrO2/Al2O3,中的FeO粒子约为40nm,较Fe0/Al2O3中FeO的粒子(100nm)小且分布均匀.     

Thermal emission properties of Al2O3/Er3Al5O12 eutectic ceramics

The mechanical properties and thermal stability of the Al₂O₃/Er₃Al₅O₁₂ (EAG) eutectic ceramics have been investigated at very high temperature. The emissive properties of this eutectic ceramics have also been measured and its possibilities of application to an emitter have been discussed. The present eutectic ceramic has excellent high-temperature strength characteristics, showing that tensile yielding stress is approximately 300 MPa at 1650 °C and superior thermal stability at 1700 °C in an air atmosphere. The present material shows strong selective emission bands at wavelength 1.5 μm due to Er³⁺ ion. The emission bands of this material are nearly coincident with the sensitive region of GaSb PV cell, therefore, the Al₂O₃/EAG eutectic ceramic can be regarded as one of the promising emitter materials in TPV systems.     

原位红外光谱法研究Pd-Ag/Al2O3和Pd/ Al2O3乙炔加氢催化剂

以一氧化碳和乙炔为探针分子,采用原位红外光谱技术研究了Pd-Ag/ Al₂O₃和Pd/ Al₂O₃催化剂上乙炔加氢反应以及催化剂本身的表面形态,动态考察了乙炔加氢的气相反应行为、CO吸附以及催化剂表面吸附物种的变化。结果表明,在Pd-Ag/ Al₂O₃催化体系中,由于Ag的加入而受到几何效应和电子效应的共同影响,引起了催化剂表面形态的改变从而改变了催化剂的性能。另外,乙炔加氢反应会导致钯催化剂表面形成由长分子链的饱和烃组成的碳氢化合物层,该碳氢化合物层有可能是加氢反应形成的绿油。     

Al2O3/Al2O3-ZrO2(3Y)层状纳米陶瓷复合材料的显微结构及弯曲强度

在Al2O3-ZrO2(3Y,即含3%Y2O3,摩尔分数,下同)纳米陶瓷的基础上,以原位合成的Al2O3和Al2O3-ZrO2(3Y)纳米粉体为原料,采用干压成型及热压烧结的方法制备了Al2O3/Al2O3-ZrO2(3Y)层状纳米陶瓷复合材料,研究了ZrO2(3Y)含量对材料显微结构及力学性能的影响.结果表明:复合材...     

Regeneration of S-poisoned Pd/Al2O3 and Pd/CeO2/Al2O3 catalysts for the combustion of methane

This work investigates the regeneration of S-poisoned Pd/Al₂O₃ and Pd/CeO₂/Al₂O₃ catalysts under different CH₄ containing atmospheres. Under lean combustion conditions in the presence of excess O₂, partial regeneration took place for both systems only above 750 °C after decomposition of stable sulphate species adsorbed on the support. Under alternate lean combustion/CH₄-reducing pulse regeneration is markedly anticipated down to 550–600 °C. Experiments evidenced an effective role of ceria in preventing PdO from sulphation and in promoting regeneration via sulphates decomposition under reducing conditions.     

Effect of CeO2 and Al2O3 contents on Ce‐ZrO2/Al2O3 composites

Effect of CeO₂ and Al₂O₃ contents on phase composition, microstructures, and mechanical properties of Ce–ZrO₂/Al₂O₃ composites was studied. The CeO₂ content in CeO₂–ZrO₂ varied from 7 to 16 mol%, and the Al₂O₃ content in Ce‐ZrO₂/Al₂O₃ composites were 7 and 22 wt%. When CeO₂ content was ≤10 mol%, high Al₂O₃ content contributed to hinder the tetragonal‐to‐monoclinic ZrO₂ phase transformation during cooling and decrease the density of microcracks in the composites. Tetragonal ZrO₂ single‐phase was obtained in the composites with ≥12 mol% CeO₂, regardless of the Al₂O₃ content. Hardness, flexural strength, and toughness were dependent on CeO₂ and Al₂O₃ contents which were related to the microcracks, grain size, and phase transformation. The high flexural strength and toughness of the composites with 7wt% Al₂O₃ could be obtained at an optimum CeO₂ content of 12 mol%, whereas those of the composites with 22 wt% Al₂O₃ could be achieved in the wide CeO₂ content range of 8.5‐12 mol%.     

Microstructure and mechanical properties of Al2O3/Y3Al5O12/ZrO2 ternary eutectic materials

Directionally solidified fibers and rods have been grown from the ternary Al₂O₃/Y₃Al₅O₁₂/ZrO₂ system using micro-pulling-down method. Fiber diameter could be varied 0.3 mm–2 mm at pull-rates ranging 6–900 mm/h and 500 mm in length. The ternary eutectic fibers had homogeneous colony patterned eutectic microstructures. The interlamellar spacing λ exhibited an inverse-square-root dependence on the growth speed v according to λ = 8 × v^−1/2, where λ has the dimension of μm and v is in μm/s. The tensile strength was recorded 1730 MPa at 25 °C and 1100 MPa at 1200 °C for a fiber crystals grown at a growth speed of 900 mm/h. Eutectic rods having 5 mm of diameter and up to 80 mm in length were also successfully grown by the micro-pulling-down method. The eutectic rods showed 1400 MPa of mechanical strength by compressive mode at 1500 °C with homogeneous colony microstructures.     

Low pressure plasma-sprayed Al2O3 and Al2O3/SiC nanocomposite coatings from different feedstock powders

This paper describes a preliminary investigation of a nanocomposite ceramic coating system, based on Al₂O₃/SiC. Feedstock Al₂O₃/SiC nanocomposite powder has been manufactured using sol-gel and conventional freeze-drying processing techniques and then low pressure plasma sprayed onto stainless steel substrates using a CoNiCrAlY bond coat. Coatings of a commercial Al₂O₃ powder have also been manufactured as a reference for phase transformations and microstructure. The different powder morphology and size distribution resulting from the different processing techniques and their effect on coating microstructure has been investigated. Phase analysis of the feedstock powders and of the as-sprayed coatings by X-ray diffractometry (XRD) and nuclear magnetic resonance (NMR) showed that the nano-scale SiC particles were retained in the composite coatings and that equilibrium α-Al₂O₃ transformed to metastable γ- and δ-Al₂O₃ phases during plasma spraying. Other minority phases in the sol-gel Al₂O₃/SiC nanocomposite powder such as silica and aluminosilicate were removed by the plasma-spraying process. Microstructure characterisation by scanning electron microscopy (SEM) of the as-sprayed surface, polished cross-section, and fracture surface of the coatings showed evidence of partially molten and unmolten particles incorporated into the predominantly lamella microstructure of the coating. The extent of feedstock particle melting and consequently the character of the coating microstructure were different in each coating because of the effects of particle morphology and particle size distribution on particle melting in the plasma.