温度及pH敏感性互穿网络水凝胶的制备研究

采用分步法制备了聚丙烯酸/N-异丙基丙烯酰胺互穿网络水凝胶,研究了互穿网络水凝胶的溶胀性能。结果表明,当水溶液的pH增大时,水凝胶的溶胀率显著增加。在一定的温度范围内,水凝胶的溶胀率随温度升高而减小。聚丙烯酸/N-异丙基丙烯酰胺互穿网络水凝胶表现出显著的温度及pH敏感双重特性。     

壳聚糖/聚醚半互穿网络水凝胶的性能

以壳聚糖和聚醚为原料,戊二醛为交联剂,在醋酸溶液中制备了壳聚糖/聚醚水凝胶,反应温度45℃,聚醚和壳聚糖的质量比为0.4,戊二醛浓度为0.053 mol/L,壳聚糖黏均相对分子质量为24.86×104时,其凝胶饱和溶胀度为876.25%;反应温度45℃,聚醚和壳聚糖的质量比为0.6,戊二醛浓度为0.267 mol/L,壳聚糖黏均相对分子质量为24.86×104时,其凝胶硬度为151.896 kPa。     

互穿网络敏感型聚氨酯水凝胶

<正>安徽大学以异佛尔酮二异氰酸酯、聚氧化丙烯二醇、二羟基丙酸和蓖麻油等为主要原料,首先合成出交联型水性聚氨酯乳液,然后加入丙烯酰胺、引发剂和交联剂等原料,经自由基聚合制备出具有IPN结构的聚氨酯/丙烯酰胺水凝胶。该产品为特殊的粘性产品,属于高分子敏感型水凝胶,可以在水中膨胀至某一平衡值(可显著溶胀但不     

硅橡胶/水凝胶半互穿网络膜的制备研究

通过交联的聚甲基乙烯基硅橡胶膜含浸甲基丙烯酸β 羟乙酯单体溶液,然后以原位聚合的方法制得硅橡胶—水凝胶半互穿网络膜。用扫描电镜观察膜的横断面,并以X射线光电子能谱研究膜的表面组成。测试膜在水中的溶胀性能及膜对小分子药物的渗透性。     

聚丙烯酸/聚乙烯醇互穿网络水凝胶制备及其对结晶紫的控制释放性能的研究

以过硫酸铵为引发剂,采用溶液聚合和连续的互穿网络技术,制备了一系列聚丙烯酸(PAA)/聚乙烯醇(PVA)互穿网络水凝胶。测量了水凝胶在不同pH缓冲溶液中的溶胀性能。以结晶紫为模板药物,考察了在不同的pH缓冲溶液中的PAA/PVA互穿网络水凝胶控释作用。结果表明,药物的释放量可以通过改变体系的pH值加以调控。     

互穿网络敏感型聚氨酯水凝胶的合成与研究

以异佛尔酮二异氰酸酯（IPDI）、聚氧化丙烯二醇（PPG-220）、二羟甲基丙酸（DMPA）、蓖麻油（C0）等为主要原料,合成交联型水性聚氨酯乳液,在此乳液中加入丙烯酰胺、引发剂（KPS）,交联剂（BMA）进行自由基聚合,制备具有IPN结构的聚氨酯-聚丙烯酰胺（PU—PAAm）水凝胶。研究了（PU—PAAm）水凝胶溶胀率（SR）受pH值、温度（T）、交联剂用量等因素的影响。     

聚氨酯／聚丙烯酸酯类胶乳互穿聚合物网络的研制

采用两步法合成了聚氨酯（ＰＵ）聚丙烯酸酯（ＰＡＡ）胶乳互穿聚合物网络（ＬＩＰＮ）。试验结果表明ＰＵ／ＰＡＡ ＬＩＰＮ具有核壳结构。     

具有pH及温度敏感性的互穿网络水凝胶的合成及其性能研究

用自由基聚合合成了具有两亲性的N-异丙基丙烯酰胺(NIPAm)与衣康酸(IA)共聚物水凝胶(NIPAm-co-IA),利用互穿网络(IPN)技术合成了壳聚糖(CS)异丙基丙烯酰胺与衣康酸互穿网络水凝胶IPN(CS/NIPAm-co-IA).研究表明, IPN(CS/NIPAm-co-IA)水凝胶具有良好的pH及温度敏感性,研究了其对辅酶A的控制释放,发现其对辅酶A具有良好的控制释放作用.     

聚天冬氨酸/聚丙烯酸互穿网络吸水性树脂的制备

以交联聚天冬氨酸(PAsp)、丙烯酸(AAc)为原料,以过硫酸钾为引发剂,以N,N′-亚甲基双丙烯酰胺为交联剂,采用分步法制备了聚天冬氨酸/聚丙烯酸(PAAc)互穿网络吸水性树脂(IPNAP),并对其结构进行了表征,探讨了AAc与PAsp质量比、引发剂用量(以单体质量计,下同)、交联剂用量(以单体质量计,下同)、AAc中和度对IPNAP吸液性能的影响。结果表明,当AAc与PAsp质量比为1.0∶1、引发剂用量为0.50%、交联剂用量为0.40%、AAc中和度为75%时,IPNAP的吸液性能最好,在蒸馏水和生理盐水中的吸液倍率分别达到826g·g-1和120g·g-1。     

聚氨酯／聚丙烯酸酯类胶乳互穿聚合物网络的研制

采用两步法合成了聚氨酯聚丙烯酸酯（ＰＡＡ）胶乳互穿聚合物网络（ＬＩＰＮ）。试验结果表明ＰＵ／ＰＡＡ ＬＩＰＮ具有核壳结构。     

壳聚糖/聚丙烯酸共聚物微球的制备及性能

以环己烷为油相,壳聚糖溶液为水相,运用反相乳液聚合法制得了具有pH敏感性的壳聚糖/聚丙烯酸共聚物微球。讨论了微球在pH=1～10缓冲溶液中的溶胀率变化,研究表明,微球在强酸性(pH≈1)和碱性(pH>7)条件下,溶胀率均在10倍以上;而在pH=2～6时溶胀较差,当pH=4时出现最低值,溶胀率低于1倍。光学显微镜所观察到的微球粒径均在40μm以内,且大小均匀。采用傅里叶红外光谱仪分析了不同配比样品特征峰的峰值和峰面积的变化。用722光栅分光光度计研究了共聚物微球包埋考马斯亮蓝的溶胀释放过程。     

Study of nanofiber scaffolds of PAA,PAA/CS,and PAA/ALG for its potential use in biotechnological applications

In recent times, electrospun nanofibers have been widely studied from several biotechnological approaches; in this work, poly(acrylic acid) (PAA) solutions mixed with chitosan and alginate were electrospun and characterized to determine the behavior of these fibers when used in combination with bacteria, different samples were incubated with the bacterial strains: Streptomyces spp., Micromonospora spp., and Escherichia coli and a OD600 test was performed. The formation of nanofibers via electrospinning and the physicochemical properties of the obtained fibers were evaluated. Results showed that the presence of chitosan enhanced the thermal stability of PAA, since PAA/alginate fibers lost 5% of their mass at 41°C, whereas PAA/chitosan lost this amount at around 125°C. The fibers demonstrated suitable characteristics to be used as a bacteria bioreactor.     

聚乙烯醇/二氧化硅互穿网络膜的研究

采用溶胶凝胶法制备了聚乙烯醇/二氧化硅有机/无机互穿网络结构。扫描电子显微镜(SEM)观察到样品表面光滑,均匀;原子力显微镜(AFM)观察到样品中无机相与有机相呈互穿网络结构,且随无机物的增多两相分布更均匀;元素分析结果为纯PVA中w(O)为38%,随着无机物的增多w(O)逐渐降低为24.9%,是硅羟基与醇羟基之间脱去水,两相之间进行交联的结果;29SiNMR表明随无机物的增多,化学位移Q3的强度有所降低而化学位移Q4值却略有上升,说明硅羟基含量逐渐减少,两相交联程度逐渐增大,与元素分析结果相印证;热重曲线(TG)表明,无机物的加入使PVA的热降解温度由400℃提高到420℃,进一步证明两相之间已形成网状结构。     

聚丙烯酸纳米纤维膜的制备及交联

通过静电纺丝制备聚丙烯酸(PAA)纳米纤维膜,并以乙二醇(EG)为交联剂、硫酸(H_2SO_4)为引发剂,对制备的PAA纳米纤维膜进行热交联,以提高其在水中的稳定性。采用扫描电子显微镜对纤维的表面形貌进行表征,发现当PAA溶液质量分数为9%、交联剂EG质量分数为12%、纺丝电压为20 k V时,溶剂挥发完全,而且纤维直径分布均匀。试验还对交联温度及交联时间进行了研究,发现PAA纳米纤维膜在140℃的热处理条件下形成酯,而在150℃及以上的热处理条件下形成酯和酸酐,且上述交联反应都能在1 h内完成。     

Crosslinking reaction of poly(vinyl alcohol) with poly(acrylic acid) (PAA) by heat treatment: Effect of neutralization of PAA

The crosslinking reaction of poly(vinyl alcohol) (PVA) by esterification using poly(acrylic acid) (PAA) as a crosslinking reagent was investigated to obtain highly insoluble PVA materials. Blend films of PVA and PAA (PVA/PAA = 8/2) were prepared to examine the effect of degree of neutralization (DN) in PAA and heat‐treatment conditions on the degree of crosslinking reaction. The degree of crosslinking reaction varied significantly when the DN of PAA changed. The optimum DN for the crosslinking reaction was in the range of 5 to 10 mol %. In the case of unneutralized PAA, the degree of crosslinking reaction was at most 15 mol % by heat treatment for 20 min at 200°C. Applying partially neutralized PAA (DN = 10 mol %) raised the degree to about 40 mol % under the same heat‐treatment conditions. FTIR analysis revealed that the hydroxyl group of PVA in the film blended with unneutralized PAA was degraded to a greater degree than that with partially neutralized PAA as a result of heat treatment. It was found that heat treatment at a low pH condition enhances the degradation of the hydroxyl group of PVA, resulting in a decrease of the number of crosslinking sites by esterification. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2420–2427, 2003     

Water Uptake Kinetics and Control Release of Agrochemical Fertilizers from Nanoclay-Assisted Semi-interpenetrating Sodium Acrylate-Based Hydrogel

Semi-interpenetrating composite hydrogels composed of poly(acrylic acid-co-sodium acrylate)/polyethylene glycol for the controlled release of fertilizers were synthesized by using nano-phyllosilicate. Hydrogel was characterized by infrared spectral analysis (Fourier transform infrared), X-ray diffraction, and scanning electron microscopy. The cross-link density (ρ_c), average molecular weight between cross-links (M_c), and the mesh size of the network (?) were also determined. The degree of neutralization of acrylic acid component has a positive impact in the swelling behavior of hydrogel, which was investigated through its swelling study and pH-oscillatory behavior. The dependency of synthesis parameters, pH and ionic strength on swelling characteristics were investigated. The type of the diffusion phenomena was investigated by calculating various kinetic parameters such as the diffusion coefficient, diffusion rate constant, swelling exponents, etc. The swelling ratio with varying synthetic parameters was recorded to investigate fourth-order factorial model. The model gives the idea of the effect of the independent parameters on the swelling ratio.     

pH敏感瓜胶-聚丙烯酸水凝胶的流变和溶胀性能研究

以可生物降解的多糖羧甲基羟丙基瓜胶、敏感功能性单体丙烯酸为主要原料、在性能增强剂粘土存在下,合成一类具有pH敏感性质的新型杂化水凝胶,同时探索所得杂化水凝胶的流变性能及其溶胀行为。结果表明,粘土的加入不仅提高凝胶的力学强度,并可显著增强凝胶的溶胀性能和pH敏感性能。     

聚丙烯酸系高吸水树脂合成和吸液性能研究

用溶液聚合法合成了聚丙烯酸系树脂(PAAS)。研究了反应温度、单体浓度、引发剂用量、交联剂用量及单体中和度对PAAS吸液性能的影响,得到了合成PAAS的较佳工艺条件。此条件下合成的产物在蒸馏水中的吸液倍率为1430g·g-1,在0 9%(m)的NaCl溶液中的吸液倍率为102g·g-1。同时也考察了PAAS在不同离子强度的NaCl、CuCl2,FeCl3和Mg Cl2、CaCl2、BaCl2以及KCl、KBr、KI溶液中的吸液性能。     

黄原胶改性制备高吸水性树脂的研究

以丙烯酸(AA)和丙烯酰胺(AM)为黄原胶(XG)的接枝改性剂,采用反向悬浮聚合法制备了高吸水性树脂——接枝改性共聚物(XG-g-AA/AM)。采用U*10(104)均匀设计法对XG-g-AA/AM的合成工艺进行了优化。结果表明:XG-g-AA/AM的最佳合成条件为m(AA)=10.0 g、w(引发剂)=0.5%(相对于单体总质量而言)、AA中和度80%和反应温度60℃,此时XG-g-AA/AM的吸水倍率为890.1 g/g、吸盐水倍率为172.2 g/g;热失重分析(TGA)结果显示,XG-g-AA/AM的热稳定性优于XG;扫描电镜(SEM)观测结果显示,XG-g-AA/AM表面形成的多孔网络结构,有利于其对水分子的接触与吸附。     

Preparation,Characterization, and Drug-Release Behaviors of a pH-Sensitive Composite Hydrogel Bead Based on Guar Gum,Attapulgite, and Sodium Alginate

A novel guar gum-g-poly (acrylic acid)/attapulgite/sodium alginate (GG-g-PAA/APT/SA) composite hydrogel bead with excellent pH sensitivity was prepared via a facile ionic gelation approach and characterized by FTIR and SEM techniques. The effect of APT content on the encapsulation efficiency (EE), swelling ratio, and drug release behaviors of the beads was investigated and the in-vitro release kinetics were also evaluated using diclofenac sodium (DS) as the model drug. The results indicate that the burst release effect of DS drug was eliminated due to the incorporation of APT, and the DS cumulative release was clearly decreased with increasing the APT content.