pH sensitive multiwalled carbon nanotubes

The CNTs-based sensors have received considerable attention because of their outstanding properties, such as faster response, higher sensitivity, and lower operating temperature. And we expect that CNTs-based electrochemical sensors offer substantial improvements in the performance of pH sensing device. This letter reports experimental results that demonstrate the pH sensing capability of the multiwalled carbon nanotubes (MWCNTs) film by using the thermal chemical vapor deposition (thermal CVD). It was found that electronic properties of MWCNTs can be changed by the introduction of different pH value solutions. The absorption of the hydroxide in pH buffer solution changes conductivity of the MWCNTs. We observed in situ measurement of electrical conductivity by cycling solution range from acid to base.     

Preparation polystyrene/multiwalled carbon nanotubes nanocomposites by copolymerization of styrene and styryl-functionalized multiwalled carbon nanotubes

Styryl-functionalized multiwalled carbon nanotubes (p-MWNTs) were prepared by esterification based on the carboxylate salt of carbon nanotubes and p-chloromethylstyrene in toluene. Then in situ radical copolymerization of p-MWNTs and styrene initiated by 2,2′-azobis(isobutyronitrile) (AIBN) was applied to synthesize composites of styryl-functionalized multiwalled carbon nanotubes and polystyrene (PS) (p-MWNTs/PS). Characterizations carried out by FT-IR, ¹H NMR, UV–vis show that styryl group covalently bond to the surface of MWNTs. The results of UV showed that the solutions of p-MWNTs/PS in chloroform have the hyperchromic effect. Transmission electron microscopy (TEM) images of p-MWNTs/PS composites and scanning electron microscopy (SEM) images of fracture surface of p-MWNTs/PS composites showed the functionalized nanotubes had a better dispersion than that of the unfunctionalized MWNTs in the matrix. The results of thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) suggested that the thermal stability of p-MWNTs/PS composites improved in the presence of MWNTs.     

Physical properties of multiwalled carbon nanotubes

Multiwalled carbon nanotubes (MWNTs), which were prepared by hydrogen arc discharge, were purified by using an infrared radiation heating system. The morphology, structure, vibrational modes and crystalline perfection of purified MWNTs were investigated by using scanning electron microscopy, high-resolution transmission electron microscopy, an X-ray diffractometer and a Raman spectrometer. Moreover, the electrical conductivity of individual purified MWNTs was measured using a two-probe method using a micro manipulator system. It turned out that the MWNTs had a high degree of graphitization, an electrical conductivity of about 1.85×10³ S cm⁻¹ along the long axis, and an enormous current density of more than 10⁷ A cm⁻².     

Thermodynamic properties of multiwalled carbon nanotubes

The experimental study of the heat capacity of multiwalled carbon nanotubes has been conducted at a constant pressure and a temperature in the range from 60 to 300 K. The derived temperature dependence of the heat capacity has been shown to differ from that of graphite. The explanation of the fact has been given in terms of the special features of phonon spectra of the above materials. Based on the experimental results and reliable literature data standard values of the basic thermodynamic functions of multiwalled carbon nanotubes (enthalpy, entropy, and Gibbs reduced energy) have been calculated.     

Ballistic conduction in multiwalled carbon nanotubes

The electrical transport in multiwalled carbon nanotubes is shown to be ballistic at room temperature with mean free paths on the order of tens of microns. The measurements are performed both in air and in the transmission electron microscope by contacting the free end of a nanotube pointing out of a fiber to a liquid metal and measuring the dependence of the nanotube resistance between the contacts. For a specific representative nanotube the resistance per unit length is found to be Rt = 31 +/- 61 omega/micron and the contact resistance with the liquid metal, Rc = 165 +/- 55 omega microns, corresponding to a mean free path l = 200 microns. Current-to-voltage characteristics are in accord with the electronic structure. The nanotubes survive high currents (up to 1 mA, i.e., current density on the order of 10(9) A/cm2). In situ electron microscopy shows that a relatively large fraction of the nanotubes do not conduct (even at high bias), consistent with the existence of semiconducting nanotubes. Discrepancies with other measurements are most likely due to damage caused to the outer layer(s) of the nanotubes during processing. The measured mean free path of clean, undamaged arc-produced multiwalled carbon nanotubes is several orders of magnitude greater than that for metals, making this perhaps the most significant property of carbon nanotubes.     

Novel fabrication of silica nanotubes using multi-walled carbon nanotubes as template

Silica nanotubes were synthesized using multi-walled carbon nanotubes (MWCNTs) as template. The as-obtained samples were characterized by infrared spectroscopy (FTIR), X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscope (FE-SEM) and photoluminescent (PL) spectroscopy. The results indicate that the thickness of the outer walls is about 10 nm and the inner diameter is completely dependent on the size of MWCNTs. The as-fabricated silica nanotubes emit a strong violet light under excitation of 250 nm.     

Preparation and structure of multiwalled carbon nanotubes

The structure of oxidized multiwalled carbon nanotubes has been studied by transmission electron microscopy and X-ray diffraction. The results demonstrate that oxidation disrupts nanotubes. Subsequent heat treatment at 300°C also changes the structure of the nanotubes, increasing their inner diameter and reducing their outer diameter.     

Removal of chromium from aqueous solution by using oxidized multiwalled carbon nanotubes

The batch removal of hexavalent chromium (Cr(VI)) from aqueous solution by using oxidized multiwalled carbon nanotubes (MWCNTs) was studied under ambient conditions. The effect of pH, initial concentration of Cr(VI), MWCNT content, contact time and ionic strength on the removal of Cr(VI) was also investigated. The removal was favored at low pH with maximum removal at pH <2. The adsorption kinetics was modeled by first-order reversible kinetics, pseudo-first-order kinetics, pseudo-second-order kinetics, and intraparticle diffusion models, respectively. The rate constants for all these kinetic models were calculated, and the results indicate that pseudo-second-order kinetics model was well suitable to model the kinetic adsorption of Cr(VI). The removal of chromium mainly depends on the occurrence of redox reaction of adsorbed Cr(VI) on the surface of oxidized MWCNTs to the formation of Cr(III), and subsequent the sorption of Cr(III) on MWCNTs appears as the leading mechanism for chromium uptake to MWCNTs. The presence of Cr(III) and Cr(VI) on oxidized MWCNTs was confirmed by the X-ray photoelectron spectroscopic analysis. The application of Langmuir and Freundlich isotherms are applied to fit the adsorption data of Cr(VI). Equilibrium data were well described by the typical Langmuir adsorption isotherm. Overall, the study demonstrated that MWCNTs can effectively remove Cr(VI) from aqueous solution under a wide range of experimental conditions, without significant Cr(III) release.     

以预锂化多壁碳纳米管为负极的锂离子电容器性能

采用内部短路方式对多壁碳纳米管负极进行不同程度的预嵌锂处理,预嵌锂时间为5,30,60min,以预嵌锂多壁碳纳米管极片作为负极,活性炭极片作为正极,组装成锂离子电容器。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)对多壁碳纳米管及电极极片进行表征分析,采用恒流充放电(GCD)和交流阻抗谱(EIS)研究预嵌锂多壁碳纳米管负极和未预嵌锂处理多壁碳纳米管负极锂离子电容器的性能。电化学测试结果表明,多壁碳纳米管负极预嵌锂大幅提高了电容器充放电性能,对比未嵌锂多壁碳纳米管电容器,在相同的电流密度下(100mA/g),能量密度提高400%。预嵌锂60min,电流密度100mA/g时,其比容量达到57F/g。在电流密度为100～3200mA/g范围内,其最高能量密度与功率密度分别达到90Wh/kg,4130W/kg。1000次充放电循环后,容量保持率维持在85%以上,表现出良好的超级电容器性能。     

Nanoporous hard carbon membranes for medical applications

Current blood glucose sensors have proven to be inadequate for long term in vivo applications; membrane biofouling and inflammation play significant roles in sensor instability. An ideal biosensor membrane material must prevent protein adsorption and promote integration of the sensor with the surrounding tissue. Furthermore, biosensor membranes must be sufficiently thin and porous in order to allow the sensor to rapidly respond to fluctuations in analyte concentration. In this study, the use of diamondlike carbon-coated anodized aluminum oxide as a potential biosensor membrane is discussed. Diamondlike carbon films and diamondlike carbon-coated anodized aluminum oxide nanoporous membranes were examined using scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, and platelet rich plasma testing. The diamondlike carbon-coated anodized aluminum oxide membranes remained free from protein adsorption during in vitro platelet rich plasma testing. We anticipate that this novel membrane could find use in immunoisolation devices, pacemakers, kidney dialysis membranes, microdialysis systems, and other devices facing biocompatibility issues that limit in vivo function.     

Variation of radial elasticity in multiwalled carbon nanotubes

Correlations between the local diameter and local radial elastic modulus in multiwalled carbon nanotubes (MWNTs) were investigated via ultrasonic force microscopy. Spatial cross-correlation analysis showed that local radial modulus variations were inversely correlated with local diameter gradients ("bamboo" structures) in MWNTs grown via chemical vapor deposition (CVD). In contrast, uniform MWNTs grown via arc discharge exhibited no such correlation, indicating that reductions of elastic modulus previously reported for CVD-grown MWNTs originated from increased defect density associated with local increases in diameter.     

电场诱导多壁碳纳米管有序排列对多壁碳纳米管/环氧树脂复合材料性能的影响

采用交流（AC）电场诱导法制备了多壁碳纳米管（MWCNTs）均匀分散且定向有序排列的MWCNTs/环氧树脂复合材料。采用SEM、偏振拉曼光谱等研究了电场强度、MWCNTs含量、加电时间及温度（黏度）等因素对MWCNTs定向排列的影响,讨论了MWCNTs有序排列对MWCNTs/环氧树脂复合材料电学和力学性能的影响。结果表明：MWCNTs沿电场方向有序排列;MWCNTs/环氧树脂复合材料施加AC电场后的拉曼强度明显高于未施加电场的情况;当MWCNTs含量从0wt%增加到0.025wt%时,MWCNTs/环氧树脂复合材料导电率从2.3×10^-12 S/cm增加到1.3×10^-8 S/cm,增加了约4个数量级;MWCNTs含量为2.5wt%时,MWCNTs/环氧树脂复合材料拉伸强度提高了26.3%。     

Synthesis and characterization of phospholipid-modified multiwalled carbon nanotubes

A simple three-step strategy to functionalize multiwalled carbon nanotubes using 1,2-distearoyl-sn-glycero-3-phosphoethanolamine phospholipids has been described. The resulting phospholipid-modified multiwalled carbon nanotubes were analyzed by TEM, AFM, NMR, IR, UV-vis and TGA techniques. The experimental results show that the use of amine-terminated phospholipids not only improves the dispersity of multiwalled carbon nanotubes in both aqueous and organic solvents greatly, but also results in the significant enhancement of biocompatibility. These findings will serve as a future biological platform for new devices ranging from biosensors to nano-detectors.     

Functionalization of the surface of multiwalled carbon nanotubes

Features of functionalization of the surface of domestic commercial multiwalled carbon nanotubes by means of the thermal oxidation in air and treatment in nitric acid or a nitric-sulfuric acid mixture has been studied using the method of differential thermal analysis.     

Light-scattering and dispersion behavior of multiwalled carbon nanotubes

Elliptically polarized light-scattering measurements were performed to investigate the dispersion behavior of multiwalled carbon nanotubes (MWNT). Xylene- and pyridine-derived MWNT powders were dispersed in water and ethanol in separate optic cells and allowed to sit undisturbed over a two-week time period after probe sonication. Continuous light-scattering measurements taken between scattering angles of 10-170 deg and repeated over several days showed that the nanotubes formed fractal-like networks. The pyridine-derived MWNTs showed greater dispersion variation over time, tending to aggregate and clump much faster than the xylene-derived tubes. The water suspensions appeared much more stable than the ethanol suspensions, which transformed into nonfractal morphology after a few hours. We relate the dispersion stability to size and fringe patterns on the outer surface of the nanotubes. Measured values of fractal dimension were distinctly lower than those in previous studies of single-walled carbon nanotubes. Profiles of both diagonal and off-diagonal scattering matrix elements are presented.     

Functionalization and solubilization of thin multiwalled carbon nanotubes

The reaction of thin multiwalled carbon nanotubes with a mixture of concentrated HNO₃ and H₂SO₄ has been studied by IR absorption and x-ray photoelectron spectroscopies. The results indicate the attachment of-C(O)OH groups to nanotubes and subsequent conversion of these groups to-C(O)Cl groups via reaction with SOCl₂ and then to-C(O)NR₂ via reaction with didodecylamine. The yield of the carboxylated nanotubes is 53%, and that of the amidated nanotubes is 28%. The O:C atomic ratio in the carboxylated tubes is 1.0:9.0. The solubility of the carboxylated tubes in water is 3.13 g/l, and that of the amidated tubes in chloroform is 1.30 g/l.     

Physical properties of CVD boron-doped multiwalled carbon nanotubes

The effects of boron doping and electron correlation on the transport properties of CVD boron-doped multiwalled carbon nanotubes are reported. The boron-doped multiwalled carbon nanotubes were characterized by TEM as well as Raman spectroscopy using different laser excitations (viz. 488, 514.5 and 647 nm). The intensity of the D-band laser excitation line increased after the boron incorporation into the carbon nanotubes. The G-band width increased on increasing the boron concentration, indicating the decrease of graphitization with increasing boron concentration. Electrical conductivity of the undoped and boron-doped carbon nanotubes reveal a 3-dimensional variable-range-hopping conductivity over a wide range of temperature, viz. from room temperature down to 2 K. The electrical conductivity is not found to be changed significantly by the present levels of B-doping. Electron Paramagnetic Resonance (EPR) results for the highest B-doped samples showed similarities with previously reported EPR literature measurements, but the low concentration sample gives a very broad ESR resonance line.     

Suspended multiwalled carbon nanotubes as self-aligned evaporation masks

We describe the nanofabrication study of self-aligned electrodes on suspended multiwalled carbon nanotube structures. When metal is deposited on a suspended multiwalled carbon nanotube structure, the nanotube acts as an evaporation mask, resulting in the formation of discontinuous electrodes. The metal deposits on the nanotubes are removed with lift-off. Using Al sacrificial layers, it was possible to fabricate self-aligned contact electrodes and control electrodes nanometers from the suspended carbon nanotubes with a single lithography step. It was also shown that the fabrication technique may also be used to form nano-gapped contact electrodes. The technique should prove useful for the fabrication of nano-electromechanical systems.     

Transmission electron microscopic study of multiwalled carbon nanotubes

Multiwalled carbon nanotubes have been studied by transmission electron microscopy, selectedarea electron diffraction, and transmission electron energy loss spectroscopy (EELS). The results demonstrate that the walls of carbon nanotubes consist of graphite-like layers with an increased interlayer spacing compared to graphite. The local density distribution in the CNTs has been evaluated from EELS scans over the nanotubes.