Experimental study of the functionality of a semisubmersible wind turbine combined with flap-type Wave Energy Converters

In the present paper the functionality of the Semisubmersible wind energy and Flap-type wave energy Converter (SFC) is examined experimentally. In order to study the functionality of the SFC, the focus is on operational environmental conditions. SFC is a combined concept that utilizes offshore wind energy and ocean wave energy for power production. Details are presented as far as the physical modelling of the wind turbine with the use of a redesigned small-scale rotor and of the Power Take-Off mechanism of the Wave Energy Converters (WECs) with the use of a configuration that is based on a mechanical rotary damper. Tests with quasi-static excitation, motion decay, regular and irregular waves without and with wind that is uniform are conducted on an 1:50 scale physical model. The experimental data are compared with numerical predictions obtained by a fully coupled numerical model using Simo/Riflex tool. A good agreement is observed between experimental and numerical predictions. The combined operation of WECs doesn't affect the tension of mooring lines nor the acceleration of nacelle and the bending moment in tower's base. The produced power of the WECs of the SFC and consequently the functionality of the SFC is estimated.     

Wind tunnel test for the NREL phase VI rotor with 2 m diameter

The aerodynamic performance of the ‘NREL Phase VI’ rotor with a 2 m diameter was tested in the open jet test section. The original rotor with a 10.06 m diameter was tested in the NASA Ames tunnel and the test result was used as validation data for the computational model. The Reynolds number of the sectional airfoils in the original test is around 1.0E6 which is too high for a conventional wind tunnel with a diameter less than 5 m. The wind tunnel test to study the Reynolds number effect on the rotor performance from Re = 0.1E6 to Re = 0.4E6 was conducted in the KARI low speed wind tunnel with a 5 m × 3.75 m open jet test section. The torque generated by the blade was directly measured by the sensor installed in the rotating axis. The variation of the Reynolds number was achieved by changing the rotational speed. Two surface conditions, free transition and forced transition were employed in this test to study the surface trip effect. The test results for the free transition condition show that the power coefficient, Cp gradually increases with the Reynolds number, but the Cp for the forced transition condition does not vary with the Reynolds number. The maximum Cp for the free transition is 0.30 and it decrease to 0.22 for the forced transition conditions at the Reynolds number 0.4E6. The downstream flow velocity measured by 5-hole probe in the wind tunnel test was compared with BEMT calculation result. The comparison results show that the torque dependency on Reynolds number in the blade is mainly originated from the airfoil drag characteristics. A model to estimate the power of full scale blade was suggested based on these measurement results. The estimated power shows a good agreement with the full scale test result.     

Analysis of technology improvement opportunities for a 1.5 MW wind turbine using a hybrid stochastic approach in life cycle assessment

This paper presents an analysis of potential technological advancements for a 1.5 MW wind turbine using a hybrid stochastic method to improve uncertainty estimates of embodied energy and embodied carbon. The analysis is specifically aimed at these two quantities due to the fact that LCA based design decision making is of utmost importance at the concept design stage. In the presented case studies, better results for the baseline turbine were observed compared to turbines with the proposed technological advancements. Embodied carbon and embodied energy results for the baseline turbine show that there is about 85% probability that the turbine manufacturers may have lost the chance to reduce carbon emissions, and 50% probability that they may have lost the chance to reduce the primary energy consumed during its manufacture. The paper also highlights that the adopted methodology can be used to support design decision making and hence is more feasible for LCA studies.     

Aggregated models of permanent magnet synchronous generators wind farms

This paper evaluates the responses of three aggregated models of a wind farm consisting of variable speed permanent magnet synchronous generator wind turbines when wind fluctuations or grid disturbances occur. These responses are compared with those of the detailed wind farm model, in order to verify the effectiveness of the studied aggregation methods for this type of wind farms. The equivalent wind farm models have been developed by adapting different aggregation criteria that already exist in technical literature and had been applied to other technologies. In this work, these methods have been modified to suit them to the permanent magnet synchronous generator technology. The results show that the three aggregated models provide very similar results to the detailed model, both in the evolution of active power when fluctuations in wind speed occur, and in the active power and DC-link voltage during the two simulated voltage dips. Notably, the aggregated model with an approximate mechanical torque offers excellent results.     

Biopower from direct firing of crop and forestry residues in China: A review of developments and investment outlook

This paper reviews developments in the direct-fired biomass power sector and provides an up to date investment outlook by calculating the Net Present Value of new investments, and the appropriate level of Feed-in-Tariff needed to stimulate future investment. An overview is provided of support policies, historical growth in installations, and main market players. A number of data sources is combined to build a database with detailed information of individual biopower projects. This data is used to describe technological and market trends, which are used in a cash flow model to calculate the NPV of a typical project. The NPV for new projects is estimated to be negative, and investment should be expected to stall without proper policy intervention. Increasing fuel prices, local competition over biomass fuel resources, lower than expected operational performance and a downturn in carbon markets have deteriorated the investment outlook. In order to ensure reasonable profitability, the Feed-In-Tariff should be increased, from the current level of 90.9 € MWh⁻¹, to between 97 and 105 € MWh⁻¹. Where possible, government organizations should help organize demand for the supply of heat. Local rural energy bureaus may help organize supply networks for biomass fuels throughout the country, in order to reduce seasonal and local fuel scarcity and price fluctuations.     

Concept study of wind power utilizing direct thermal energy conversion and thermal energy storage

Present wind power is intermittent and cannot be used as the baseload energy source. Concept study of wind power utilizing direct thermal energy conversion and thermal energy storage named Wind powered Thermal Energy System (WTES) is conducted. The thermal energy is generated from the rotating energy directly at the top of the tower by the heat generator, which is a kind of simple and light electric brake. The rest of the system is the same as the tower type concentrated solar power (CSP). The cost estimation suggests that the energy cost of WTES is less than that of the conventional wind power, which must be supported by the backup thermal plants and grid enhancement. The light heat generator reduces some issues of wind power such as noise and vibration.     

A new methodology for urban wind resource assessment

In the latest years the wind energy sector experienced an exponential growth all over the world. What started as a deployment of onshore projects, soon moved to offshore and, more recently to the urban environment within the context of smart cities and renewable micro-generation. However, urban wind projects using micro turbines do not have enough profit margins to enable the setup of comprehensive and expensive measurement campaigns, a standard procedure for the deployment of large wind parks. To respond to the wind assessment needs of the future smart cities a new and simple methodology for urban wind resource assessment was developed. This methodology is based on the construction of a surface involving a built area in order to estimate the wind potential by treating it as very complex orography. This is a straightforward methodology that allows estimating the sustainable urban wind potential, being suitable to map the urban wind resource in large areas. The methodology was applied to a case study and the results enabled the wind potential assessment of a large urban area being consistent with experimental data obtained in the case study area, with maximum deviations of the order of 10% (mean wind speed) and 20% (power density).     

Fuel properties of Brassica juncea oil methyl esters blended with ultra-low sulfur diesel fuel

Brassica juncea is a drought-tolerant member of the Brassicaceae plant family with high oil content and a short growing season that is tolerant of low quality soils. It was investigated as a feedstock for production of biodiesel along with evaluation of subsequent fuel properties, both neat and in blends with petroleum diesel fuel. These results were compared against relevant fuel standards such as ASTM D6751, EN 14214, ASTM D975, EN 590, and ASTM D7467. Crude B. juncea oil was extracted from unconditioned seeds utilizing a continuous tubular radial expeller. The oil was then chemically refined via degumming, neutralization and bleaching to render it amenable to direct homogeneous sodium methoxide-catalyzed transesterification. The principal fatty acid detected in B. juncea oil was erucic acid (44.1%). The resulting biodiesel yielded fuel properties compliant with the biodiesel standards with the exception of oxidative stability and kinematic viscosity in the case of EN 14214. Addition of tert-butylhydroquinone and blending with soybean oil-derived biodiesel ameliorated these deficiencies. The fuel properties of B5 and B20 blends of B. juncea oil methyl esters (BJME) in ultra-low sulfur (<15 ppm S) diesel (ULSD) fuel were within the ranges specified in the petrodiesel standards ASTM D975, EN 590 and ASTM D7467 with the exception of derived cetane number in the case of EN 590. This deficiency was attributed to the inherently low cetane number of the certification-grade ULSD, as it did not contain performance-enhancing additives. In summary, this study reports new fuel property data for BJME along with properties of B5 and B20 blends in ULSD. Such results will be useful for the development of B. juncea as an alternative source of biodiesel fuel.     

Assessing ecological risks of offshore wind power on Kattegat cod

Offshore wind power is expanding with particular development plans in the Baltic and the North Sea. To reassure an environmentally acceptable development, regulatory authorities need to make informed decisions even when evidence and experience are scarce. In this study Ecological Risk Assessment (ERA) has been applied on a wind farm project in Kattegat, proposed within a spawning ground for the Kattegat cod, a threatened population of Atlantic cod (Gadus morhua L.). Six stressors with potential impacts on cod and related to wind farms were investigated. Three of them – extreme noise from pile driving, noise from vessels, and disturbances due to cable-trenching – are related to the construction phase, while lubricant spills and noise from turbines together with electric fields from cables are related to the operation phase. The ecological risk was derived from the combined likelihood and magnitude of potential adverse effects from stressors to the cod population using a weight-of-evidence (WOE) ranking procedure. Available evidence was evaluated based on its reliability, and contradictory arguments were balanced against each other using evidence maps. The option of performing hazardous construction events (e.g. pile-driving) outside biologically sensitive periods was incorporated in the assessment. It was shown that the construction of the wind farm poses a high risk to cod, as defined by the ranked and combined likelihoods and magnitudes of adverse effects. However by avoiding particular construction events during the cod recruitment period ecological risks can be significantly reduced. Specifically for this case, ecological risks are reduced from high to low by avoiding pile-driving from December through June, which confirms previous indications that pile-driving is the most ecologically hazardous activity of offshore wind power development. Additional risk reduction is achieved by avoiding cable trenching from January through May. The study thus illustrates the effectiveness of time-planning for risk reduction. Importantly, the study illustrates how combined ERA and WOE methods can be valuable for handling uncertainties of environmental impacts within offshore industrial development.     

Biosynthesis of β-caryophyllene,a novel terpene-based high-density biofuel precursor,using engineered Escherichia coli

β-caryophyllene is a common sesquiterpene compound currently being studied as a promising precursor for the production of high-density fuels. Acute demand for high-density fuels has provided the impetus to pursue biosynthetic methods to produce β-caryophyllene from reproducible sources. In this study, we produced β-caryophyllene by assembling a biosynthetic pathway in an engineered Escherichia coli strain of which phosphoglucose isomerase gene has been deleted. The 1- deoxy-d-xylulose 5-phosphate (DXP) or heterologous mevalonate (MVA) pathways were employed. Meanwhile, geranyl diphosphate synthase, glucose-6-phosphate dehydrogenase and β-caryophyllene synthase genes were co-overexpressed in the above strain. The final genetically modified strain, YJM59, produced 220 ± 6 mg/L of β-caryophyllene in flask culture. We also evaluated the use of fed-batch fermentation for the production of β-caryophyllene. After induction for 60 h, the YJM59 strain produced β-caryophyllene at a concentration of 1520 mg/L. The volumetric production fermented in the aerobic fed-batch was 0.34 mg/(L·h·OD₆₀₀) and the conversion efficiency of glucose to β-caryophyllene (gram to gram) was 1.69%. Our results are the first successful attempt to produce β-caryophyllene using E. coli BL21(DE3), and provide a new strategy that is green and sustainable for the production of β-caryophyllene.     

A numerical approach for planning offshore wind farms from regional to local scales over the Mediterranean

Renewable energy resources, such as wind, are available worldwide. Locating areas with high and continual wind sources are crucial in pre-planning of wind farms. Vast offshore areas are characterized by higher and more reliable wind resources in comparison with continental areas. However, offshore wind energy production is in a quite preliminary phase. Elaborating the potential productivity of wind farms over such areas is challenging due to sparse in situ observations. The Mediterranean basin is not an exception. In this study we are proposing numerical simulations of near-surface wind fields from regional climate models (RCMs) in order to obtain and fill the gaps in observations over the Mediterranean basin. Four simulations produced with two regional climate models are examined here. Remote sensing observations (QuikSCAT satellite) are used to assess the skill of the simulated fields. A technique for estimating the potential energy from the wind fields over the region is introduced. The wind energy potential atlas and the map of a wind turbine's functional range are presented, locating the potentially interesting sub-regions for wind farms. The ability of models to reproduce the annual cycle and the probability density function of wind speed anomalies are detailed for specified sub-regions.     

Experimental study on the role of ethanol on performance emission trade-off and tribological characteristics of a CI engine

An experimental study of engine combustion, performance and emission characteristics using diesel–ethanol blends along with investigation of tribological effects of ethanol on engine oil was done in present work using 1-butanol as emulsifier. Thorough observations of diesel–ethanol miscibility resulted that 25% v/v ethanol is miscible with diesel using only 3% v/v emulsifier. Tribological effects of ethanol on engine oil were investigated by analyzing the engine oil samples through FT-IR (Fourier Transform Infrared Spectroscopy). Overall experimentation re-evaluated the potential of ethanol in reduction of NO_x, Soot and in-cylinder temperature with slight penalty for HC, CO and BSEC prominently at low load. All fuels produced more NO but lesser NO₂ at higher load satisfying Zeldovich mechanism. A comparative trade-off analysis was done in between NHC, Soot and BSEC to reflect the performance and emission characteristics at a time. Trade-off study revealed D78E20B02 (78% diesel 20% ethanol 2% butanol) as optimal blend among all fuels used in present work. FT-IR analysis depicted negligible variation in the compounds in engine oil samples for the specified operational period. Statistical analysis showed larger Coefficient of variation for D78E20B02 blend due to higher absorbance of a particular compound.     

Anaerobic digestion of corn silage on a commercial scale: Differential utilization of its chemical constituents and characterization of the solid digestate

The utilization of different chemical constituents of corn silage during industrial-scale anaerobic digestion was determined. Corn silage together with the resulting solid digestate generated during biogas production were collected from an industrial plant during a regular operating period. Moisture, water and ethanol extractives, ash, total nitrogen, starch, cellulose, the monomeric composition of hemicellulose, acid soluble and acid insoluble lignin were measured in both corn silage and corn silage solid digestate. The relative consumption of each component of corn silage during its anaerobic digestion was estimated with reference to acid insoluble lignin. It was assumed that lignin was not digested throughout the process. Starch and large fractions of extractives and acid soluble lignin were digested. In contrast, the digestion of cellulose and particularly hemicellulose were limited (40% and 29% respectively). Of the hemicellulose monomers, xylose was the least digested (20%). The present work shows that the digestate produced by commercial corn-silage anaerobic digestion contains a notable quantity of cell wall polymers. These could potentially be used in biorefinery processes, e.g. ethanol and xylo-oligosaccharide production.     

Fuel property enhancement of biodiesel fuels from common and alternative feedstocks via complementary blending

Fatty acid methyl esters (biodiesel) prepared from field pennycress and meadowfoam seed oils were blended with methyl esters from camelina, cottonseed, palm, and soybean oils in an effort to ameliorate technical deficiencies inherent to these biodiesel fuels. For instance, camelina, cottonseed, and soybean oil-derived biodiesels exhibited poor oxidative stabilities but satisfactory kinematic viscosities. Field pennycress and meadowfoam seed oil methyl esters yielded excellent cold flow properties but high kinematic viscosities. Thus, field pennycress and meadowfoam-derived biodiesel fuels were blended with the other biodiesels to simultaneously ameliorate cold flow, oxidative stability, and viscosity deficiencies inherent to the individual fuels. Highly linear correlations were noted between blend ratio and cold flow as well as viscosity after least squares statistical regression whereas a non-linear relationship was observed for oxidative stability. Equations generated from statistical regression were highly accurate at predicting KV, reasonably accurate for prediction of cold flow properties, and less accurate at predicting oxidative stability. In summary, complementary blending enhanced fuel properties such as cold flow, kinematic viscosity, and oxidative stability of biodiesel.     

Sunflower as a biofuels crop: An analysis of lignocellulosic chemical properties

Four accessions of cultivated sunflower (Helianthus annuus) and silverleaf sunflower (Helianthus argophyllus), were each grown in three locations (Georgia, British Columbia, and Iowa) at different planting densities and phenotyped for biomass-related traits and wood biochemistry. In most environments, H. argophyllus produced significantly more biomass than H. annuus. Cell wall chemistry for a subset of plants grown in Georgia and Iowa was assessed using analytical wet chemistry methods to measure lignin and sugar content/composition. The analysis of lignin and the S/G-lignin ratios for a larger number of samples (n > 250) was also assessed by high-throughput pyrolysis Molecular Beam Mass Spectrometry. Average pyMBMS estimated lignin content (i.e., dry weight fraction) for 60 °C dried basal stem samples of H. annuus and H. argophyllus was 29.6% (range, 24.0%–34.6%) and 28.6% (range, 24.6%–33.3%), respectively when averaged across all environments. The average S/G lignin mass ratio was 1.5 (range, 1.0–2.0) for H. annuus and 1.7 (range, 1.0–2.4) in H. argophyllus. Stem samples from these two species only differed statistically for a few cell wall chemistry traits; however, accession level differences within each species were apparent. Cell wall chemistry in both species was significantly affected by both location and planting density, thus demonstrating the need to select for these traits in the environment for which the crop will be produced. Overall, these results show that cultivated sunflower and silverleaf sunflower both possess the necessary phenotypic diversity to facilitate the development of a hybrid sunflower with improved lignocellulosic biofuels traits, namely increased biomass, decreased lignin, and increased glucan.     

Estimating the offshore wind resources of the State of Ceará in Brazil

The onshore wind power is consolidated; the challenge is to reach the same level of maturity for offshore exploitation. Brazil has no offshore wind power plants and there are few studies in this direction. This paper aims to estimate the offshore wind resources in the State of Ceará, in Brazil. The investigation uses a mesoscale atmospheric computer model, the Regional Atmospheric Modeling System (RAMS), with horizontal resolution of 2 km, which estimates the offshore average wind speed, average wind direction, power density and turbulence taking into account the bathymetry data and navigation routes along the coast of Ceará. The wind potential was evaluated in three representative periods, La Niña, El Niño and Neutral year, analyzing the dry and rainy season for each period. The results indicate an average wind speed above 8 m/s and power density above 720 W/m² no matter the period evaluated, in the dry season. The predominant wind direction in the observed dry periods was from East to West and the turbulence intensity is smaller during dry season of El Niño. Besides, the bathymetry of the State of Ceará is shallow and the large ships route is far beyond the coast, offering no danger to future endeavors.     

Steam explosion pretreatment and enzymatic saccharification of duckweed (Lemna minor) biomass

Our previous research has shown that duckweed is potentially an ideal feedstock for the production of biofuels because it can be effectively saccharified enzymatically. Here we report the results of experiments in which duckweed was pre-treated by steam explosion prior to enzyme digestion. A range of temperatures, from 130 to 230 °C with a fixed retention time of 10 min, were employed. The best pretreatment conditions were 210 °C for 10 min; these conditions produced the highest amount of water-soluble material (70%), the greatest levels of starch solubilisation (21%) and hemicellulose and pectic polysaccharides degradation (60%). The use of these steam explosion conditions enabled large reductions in the concentrations of enzymes required for effective saccharification. The amount of Celluclast required was reduced from 100 U (4.35 FPU) g⁻¹ substrate to 20 U g⁻¹ substrate, and additional beta-glucosidase was reduced from 100 to 2 U g⁻¹ substrate.     

Anaerobic digestion of maize and cellulose under thermophilic and mesophilic conditions – A comparative study

The aim of this study was to advance in understanding of digestion process of energy crops. Cellulose and maize silage were fermented in batch mode at mesophilic (38 °C) and thermophilic (55 °C) conditions and corresponding organic loads of 5.5 ± 0.2 kgVS/m³, 11.2 ± 0.3 kgVS/m³ and 16.7 ± 0.4 kgVS/m³.For both substrates more stable and faster digestion took place at 38 °C. Due to complex structure maize degradation was characterized by varying digestion rate and longer total digestion time resulting form breakdown of hard-degradable fractions. The digestion retard at increased OLRs of cellulose and lower degradation level obtained for all cellulose series confirm a higher overloading potential for systems dealing with single-component-substrates but also the enhanced sensitivity of such systems to any inconvenient digestion conditions.Based on observed patterns of volatile fatty acids and oxidation-reduction potential, different fermentation mechanisms can be concluded for cellulose and maize, but also for different temperature modes. Conversion of maize at highly reductive conditions with increased concentrations of butyric acid was accompanied by much higher activity of hydrogenotrophic methanogens than for cellulose digestion.Two factors showed a strong potential to influence test results: an insufficient VS content of inoculum, which caused reduced biogas yields, and a high natural biodiversity of maize silage, resulting in higher biogas yields than calculated based on the maize composition.     

Breakeven price of biomass from switchgrass,big bluestem,and Indiangrass in a dual-purpose production system in Tennessee

The objective was to determine the breakeven price for switchgrass (SG) (Panicum virgatum L.), a mix of big bluestem (Andropogon gerardii Vitman) and Indiangrass (BBIG) (Sorghastrum nutans L. Nash), and a combination of SG and BBIG (SG/BBIG) produced under three harvest treatments. Two-harvest treatments included a forage harvest at early boot (EB) and at early seedhead (ESH) plus a biomass harvest at fall dormancy (FD). The third harvest treatment was a single biomass harvest at FD. Mixed models were used to determine if there were differences in yield, crude protein, and nutrient removal for each of the native warm-season grass (NWSG) treatments at each harvest. The EB plus FD harvest system would be preferred over the ESH plus FD harvest system for all NWSG treatments. BBIG was the only NWSG treatment with a breakeven price for biomass that decreased with an EB harvest. For all three NWSG treatments, a producer would be better off harvesting once a year for biomass than twice for forage and biomass. The cost of harvesting and replacing the nutrients for the forage harvest was greater than the revenue received from selling the forage.     

Chemical–mechanical pretreatment of wood: Reducing downsizing energy and increasing enzymatic digestibility

A chemimechanical (CM) pretreatment method was devised, wherein wood chips are acid-treated to weaken the physical structure then disc-refined to produce a fibrous substrate. CM pretreatment was directly compared with a common dilute acid (DA) pretreatment method, wherein wood is mechanically downsized to a powder or fiber substrate and then acid-treated. It was hypothesized that the CM pretreatment sequence would reduce the energy required for size reduction and increase enzymatic digestibility of the pretreated substrate. By treating wood chips in a dilute sulfuric acid liquor before the mechanical downsizing step, the net specific energy (NSE) of disc-refining was reduced by up to 95%. At the optimal acid treatment and disc-refining conditions determined within this work, CM pretreatment could produce a highly digestible lignocellulose substrate (95% cellulose conversion) while requiring less than 100 kWh/tonne od NSE for mechanical downsizing. A comparison of CM and DA pretreated hardwood revealed that CM pretreatment produced a significantly more digestible substrate than DA pretreatment. Differences in the digestibility of CM and DA pretreated substrates were attributed to differences in physical structure. CM pretreatment produced a substrate that consisted primarily of single fibers and small fiber bundles, while DA pretreatment produced larger fiber bundles. Furthermore, the CM pretreated substrate had a more accessible pore structure, and an altered distribution of surface lignin.