共查询到20条相似文献,搜索用时 234 毫秒
1.
2.
本文利用高波数分辨率的显微喇曼方法测量了AlGaN/GaN 高电子迁移率晶体管(HEMT)的沟道温度。利用显微喇曼系统JYT-64000测量了GaN材料E2模的喇曼声子频率的温度特性。通过洛仑兹拟合方法,喇曼声子频率的实际测量不确定度为?0.035cm-1, 对应于GaN材料温度精度为?3.2℃,为国际所见报道的最高水平。测得的AlGaN/GaN HEMT样品的沟道-管壳热阻为22.8℃/W,与三维热传导模型的仿真结果吻合良好。给出了由显微喇曼方法、脉冲电学法及红外热像法测量出的沟道温度差别的定量分析。 相似文献
3.
4.
5.
6.
对蓝宝石衬底上的InGaN/GaN和InGaN/AlGaN多量子阱结构和经激光剥离去除衬底的InGaN/GaN和InGaN/AlGaN多量子阱结构薄膜样品,进行了光致发光谱、高分辨XRD和喇曼光谱测量.PL测量结果表明,相对于带有蓝宝石衬底的样品,InGaN/GaN多量子阱薄膜样品的PL谱峰值波长发生较小的蓝移,而InGaN/AlGaN多量子阱薄膜样品的PL谱峰值波长发生明显的红移;喇曼光谱的结果表明,激光剥离前后E2模的峰值从569.1减少到567.5cm-1.这说明激光剥离去除衬底使得外延层整体的压应力得到部分释放,但InGaN/GaN与InGaN/AlGaN多量子阱结构中阱层InGaN的应力发生了不同的变化.XRD的结果证实了这一结论. 相似文献
7.
对蓝宝石衬底上的InGaN/GaN和InGaN/AlGaN多量子阱结构和经激光剥离去除衬底的InGaN/GaN和InGaN/AlGaN多量子阱结构薄膜样品,进行了光致发光谱、高分辨XRD和喇曼光谱测量.PL测量结果表明,相对于带有蓝宝石衬底的样品,InGaN/GaN多量子阱薄膜样品的PL谱峰值波长发生较小的蓝移,而InGaN/AlGaN多量子阱薄膜样品的PL谱峰值波长发生明显的红移;喇曼光谱的结果表明,激光剥离前后E2模的峰值从569.1减少到567.5cm-1.这说明激光剥离去除衬底使得外延层整体的压应力得到部分释放,但InGaN/GaN与InGaN/AlGaN多量子阱结构中阱层InGaN的应力发生了不同的变化.XRD的结果证实了这一结论. 相似文献
8.
提出一种新的钝化技术--采用盐酸和氢氟酸混合预处理溶液(HF:HCI:H2O=1:4:20)对AIGaN/GaNHEMTs进行表面预处理后冉淀积Si3N4钝化,研究了新型钝化技术对AlGaN/GaN HEMTs性能的影响并分析其机理.与用常规方法钝化的器件相比,经过表面顶处理再钝化,成功地抑制了 AIGaN/GaN HEMTs肖特基特性的恶化,有效地增强抑制电流崩塌效应的能力,将GaN基HEMTs的输出功率密度提高到5.2W/mm,并展现良好的电学可靠性.通过X射线光电子谱(XPS)检测预处理前后的AIGaN表面,观察到经过预处理后的AIGaN表面氧元素的含量大幅度下降.表面氧元素的含量下降,能有效地降低表面态密度和表面电荷陷阱密度,被认为是提高AIGaN/GaN HEMTs性能的主要原因. 相似文献
9.
对蓝宝石衬底上的InGaN/GaN和InGaN/AlGaN多量子阱结构和经激光剥离去除衬底的InGaN/GaN和InGaN/AlGaN多量子阱结构薄膜样品,进行了光致发光谱、高分辨XRD和喇曼光谱测量. PL测量结果表明,相对于带有蓝宝石衬底的样品,InGaN/GaN多量子阱薄膜样品的PL谱峰值波长发生较小的蓝移,而InGaN/AlGaN多量子阱薄膜样品的PL谱峰值波长发生明显的红移;喇曼光谱的结果表明,激光剥离前后E2模的峰值从569.1减少到567.5cm-1. 这说明激光剥离去除衬底使得外延层整体的压应力得到部分释放,但InGaN/GaN与InGaN/AlGaN多量子阱结构中阱层InGaN的应力发生了不同的变化. XRD的结果证实了这一结论. 相似文献
10.
提出一种新的钝化技术--采用盐酸和氢氟酸混合预处理溶液(HF:HCI:H2O=1:4:20)对AIGaN/GaNHEMTs进行表面预处理后冉淀积Si3N4钝化,研究了新型钝化技术对AlGaN/GaN HEMTs性能的影响并分析其机理.与用常规方法钝化的器件相比,经过表面顶处理再钝化,成功地抑制了 AIGaN/GaN HEMTs肖特基特性的恶化,有效地增强抑制电流崩塌效应的能力,将GaN基HEMTs的输出功率密度提高到5.2W/mm,并展现良好的电学可靠性.通过X射线光电子谱(XPS)检测预处理前后的AIGaN表面,观察到经过预处理后的AIGaN表面氧元素的含量大幅度下降.表面氧元素的含量下降,能有效地降低表面态密度和表面电荷陷阱密度,被认为是提高AIGaN/GaN HEMTs性能的主要原因. 相似文献
11.
Both transient temperature and thermal stress responses in high power multi-finger AlGaN/GaN high electron mobility transistors (HEMTs), caused by their self-heating effects, are characterized in the present study. Instead of using commercial software, self-developed algorithm based on hybrid time-domain finite element method (TD-FEM) is applied for thermo-mechanical co-simulation of such 3-D structure. The temperature-dependent properties of most constitutive parameters of all materials involved, in particular for electrical conductivities, thermal conductivities, thermal expansion coefficients, and Young’s modulus, are described by several sets of nonlinear polynomial expressions. The algorithm accuracy is validated in detail, with good agreement achieved in comparison with the commercial software COMSOL. It is believed that this study will be useful for effectively evaluating the reliability and lifetime of AlGaN/GaN HEMTs and their monolithic microwave integrated circuits (MMIC) used in high power communication systems and radars. 相似文献
12.
Investigation of Self-Heating Effects in Submicrometer GaN/AlGaN HEMTs Using an Electrothermal Monte Carlo Method 总被引:1,自引:0,他引:1
Toufik Sadi Robert W. Kelsall Neil J. Pilgrim 《Electron Devices, IEEE Transactions on》2006,53(12):2892-2900
An electrothermal Monte Carlo (MC) method is applied in this paper to investigate electron transport in submicrometer wurtzite GaN/AlGaN high-electron mobility transistors (HEMTs) grown on various substrate materials including SiC, Si, GaN, and sapphire. The simulation method is an iterative technique that alternately runs an MC electronic simulation and solves the heat diffusion equation using an analytical thermal resistance matrix method. Results demonstrate how the extent of the thermal droop in the Id-Vds characteristics and the device peak temperature depend upon both the biasing conditions and the substrate material type. Polarization effects are considered in the simulations, as they greatly influence electron transport in GaN/AlGaN HEMTs by creating a highly concentrated two-dimensional electron gas (2DEG) at the GaN/AlGaN interface. It is shown that a higher 2DEG density provides the devices with a better current handling capability but also increases the importance of the thermal effects 相似文献
13.
版图设计对多指AlGaN/GaN HEMTs 栅指温度影响的研究 总被引:1,自引:1,他引:0
本文利用三维热仿真方法研究了不同版图设计对多指AlGaN/GaN 高电子迁移率器件工作温度的影响。我们使用拉曼微区测温技术测量了样品的沟道温度,并用于确定材料的热导率,验证器件热模型的准确性。建立模型时特别考虑了界面热阻的作用,确保器件温度分布的仿真结果与实验测量结果一致。文中采用包含界面热阻效应的三维热模型,系统的分析了栅指数目,器件栅宽和栅栅间距等因素对AlGaN/GaN 高电子迁移率晶体管热特性的影响。最后,提出了一种优化器件栅指间距的热设计方法,能够有效降低器件工作时的最高温度。 相似文献
14.
Low-frequency noise characteristics in ion-implanted GaN/AlGaN/GaN and AlGaN/GaN HEMTs were investigated. The normalized spectral noise density was about 6 dB lower in GaN/AlGaN/GaN HEMTs than in AlGaN/GaN HEMTs. The normalized spectral noise density dependence on the gate length Lg indicates that the main origin of low-frequency noise is at the region under the gate in both devices. The Hooge parameters alphaH for both devices are on the order of 10-1-10- 2. The ion implantation process introduces a lot of defects in the source/drain regions, but the values of alphaH are comparable with those for conventional GaN-based HEMT devices. The values of alphaH are also lower in GaN/AlGaN/GaN HEMTs than in AlGaN/GaN HEMTs, which is due to the decrease of surface potential fluctuations in GaN/AlGaN/GaN HEMTs. 相似文献
15.
16.
17.
高频功率AlGaN/GaN HEMT 的栅结构优化 总被引:2,自引:2,他引:0
本文研究了栅帽、栅源间距对AlGaN/GaN HEMT性能的影响。基于研究结果得出了优化高频功率AlGaN/GaN HEMT栅结构的方法。缩小栅场板可以有效提高器件的增益、截止频率(ft)、最大震荡频率(fmax)。通过减小栅场板长度,栅长0.35 器件的ft达到了30GHz、fmax达到了80GHz。采用tao型栅(栅帽偏向源侧)或者增加栅金属厚度还可以进一步优化 。缩小栅源的距离可以提高饱和漏电流和击穿电压,从而提高器件的输出功率。 相似文献
18.
14W X波段AlGaN/GaN HEMT功率MMIC 总被引:2,自引:1,他引:1
报道了研制的SiC衬底AIGaN/GaN HEMT微带结构微波功率MMIC,芯片工艺采用凹槽栅场板结构提高AlGaN/GaNHEMTs的微波功率特性.S参数测试结果表明AlGaN/GaN HEMTs的频率特性随器件的工作电压变化显著.研制的该2级功率MMIC在9~11GHz带内30V工作,输出功率大于10W,功率增益大于12dB,带内峰值输出功率达到14.7W,功率增益为13.7dB,功率附加效率为23%,该芯片尺寸仅为2.0mm×1.1mm.与已发表的X波段AlGaN/GaN HEMT功率MMIC研制结果相比,本项工作在单位毫米栅宽输出功率和芯片单位面积输出功率方面具有优势. 相似文献
19.
20.
采用一个AlN缓冲层和两个Al组分阶变的AlGaN过渡层作为中间层,在76.2mm Si衬底上外延生长出1.7μm厚无裂纹AlGaN/GaN异质结材料,利用原子力显微镜、X射线衍射、Hall效应测量和CV测量等手段对材料的结构特性和电学性能进行了表征。材料表面平整光滑,晶体质量和电学性能良好,2DEG面密度为1.12×1013cm-2,迁移率为1 208cm2/(V.s)。由该材料研制的栅长为1μm的AlGaN/GaN HEMT器件,电流增益截止频率fT达到10.4GHz,这些结果表明组分阶变AlGaN过渡层技术可用于实现高性能Si基GaN HEMT。 相似文献