Mechanical Properties of Si3N4-SiC Three-Layer Composite Materials

The effects of microstructure and residual stress on the mechanical properties of Si₃N₄-based three-layer composite materials were investigated. The microstructure of each layer was controlled by the addition of two differently sized silicon carbides: fine SiC nanoparticles (∼200 nm) or relatively large SiC platelets (∼20 µm). When the SiC nanoparticles were added, the average grain size of Si₃N₄ was reduced because of the inhibition of grain growth by the particles. On the other hand, when the SiC platelets were added, the microstructure of Si₃N₄ was not much changed because of the large size of the platelets. Three-layer composites were fabricated by placing the Si₃N₄/SiC-nanoparticle layers on the surface of the Si₃N₄/SiC-platelet layer. The residual stress was controlled by varying the amount of SiC added. The mechanical properties of three-layer composites with various combinations of microstructure and residual stress level were investigated.     

High-Temperature Failure Mechanisms of Hot-Pressed Si3N4 and Si3N4/Si3N4-Whisker-Reinforced Composites

The high-temperature flexural strength of hot-pressed silicon nitride (Si₃N₄) and Si₃N₄-whisker-reinforced Si₃N₄-matrix composites has been measured at a crosshead speed of 1.27 mm/min and temperatures up to 1400°C in a nitrogen atmosphere. Load–displacement curves for whisker-reinforced composites showed nonelastic fracture behavior at 1400°C. In contrast, such behavior was not observed for monolithic Si₃N₄. Microstructures of both materials have been examined by scanning and transmission electron microscopy. The results indicate that grain-boundary sliding could be responsible for strength degradation in both monolithic Si₃N₄ and its whisker composites. The origin of the nonelastic failure behavior of Si₃N₄-whisker composite at 1400°C was not positively identified but several possibilities are discussed.     

Oxidation and Strength Retention of Monolithic Si3N4 and Nanocomposite Si3N4-SiC with Yb2O3 as a Sintering Aid

The oxidation behaviors of monolithic Si₃N₄ and nanocomposite Si₃N₄-SiC with Yb₂O₃ as a sintering aid were investigated. The specimens were exposed to air at temperatures between 1200° and 1500°C for up to 200 h. Parabolic weight gains with respect to exposure time were observed for both specimens. The oxidation products formed on the surface also were similar, i.e., a mixture of crystalline Yb₂Si₂O₇ and SiO₂ (cristobalite). However, strength retention after oxidation was much higher for the nanocomposite Si₃N₄-SiC compared to the monolithic Si₃N₄. The SiC particles of the nanocomposite at the grain boundary were effective in suppressing the migration of Yb³⁺ ions from the bulk grain-boundary region to the surface during the oxidation process. As a result, depletion of yttribium ions, which led to the formation of a damaged zone beneath the oxide layer, was prevented.     

Microstructure and Chemical Reaction in a Si3N4–TiC Composite

The effects of TiC addition to Si₃N₄ on microstructure and the chemical aspects of Si₃N₄–TiC interphase reaction were investigated in samples hot-pressed at 1800°C in Ar and N₂. Composition of a TiC_1–xN_x solid solution was predicted based on thermodynamic calculation, with titanium carbonitride taken to be an ideal solid solution. The predicted value of x = 0.7 is slightly higher than that derived from the measured lattice parameter and Vegard's law (x = 0.67). Four distinguishable areas were observed in samples hot-pressed in nitrogen atmosphere. They were identified as β-Si₃N₄, mixtures of TiC and titanium carbonitride solid solution, SiC with twins, and iron silicide. As the duration of hot-pressing increased, more titanium carbonitride was formed, while less TiC phase remained. Thermodymanic calculations indicate one source of nitrogen gas came from the decomposition of Si₃N₄. The TiC particles also became more irregular, and reactants were found inside or between TiC as the hot-pressing time was extended. Silicon carbide was not detected in samples which were hot-pressed in argon atmosphere; however, numerous pores were found around TiC.     

Hot Isostatic Pressing of Si3N4 Powder Compacts and Reaction-Bonded Si3N4

Hot isostatically pressed silicon nitride was produced by densifying Si₃N₄ powder compacts and reaction-bonded Si₃N₄ (RBSN) parts with yttria as a sintering additive. The microstructure was analyzed using scanning electron microscopy, X-ray diffraction, and density measurements. The influence of the microstructure on fracture strength, creep, and oxidation behavior was investigated. It is assumed that the higher amount of oxygen in the Si₃N₄ starting powder compared with the RBSN starting material leads to an increased amount of liquid phase during densification. This results in grain growth and in a larger amount of grain boundary phase in the hot isostatically pressed material. Compared with the hot isostatically pressed RBSN samples therefore, strength decreases whereas the creep rate and the weight gain during oxidation increase.     

Relation Between Strength, Fracture Energy, and Microstructure of Hot-Pressed Si3N4

A fracture mechanics approach was used to investigate the high strength of hot-pressed Si₃N₄. Room-temperature flexural strengths, fracture energies, and elastic moduli were determined for material fabricated from α- and β-phase Si₃N₄ powders. When the proper powder preparation technique was used, α-phase powder resulted in a high fracture energy (69,000 ergs/cm²), a high flexural strength (95,000 psi), and an elongated (fiberlike) grain morphology, whereas β-phase powder produced a low fracture energy (16,000 ergs/cm²), a relatively low strength (55,000 psi), and an equiaxed grain morphology. It was hypothesized that the high strength of Si₃N₄ hot-pressed from α-phase powder results from its high fracture energy, which is attributed to the elongated grains. High-strength Si₃N₄ has directional properties caused, in part, by the elongated grain structure, which is oriented preferentially with respect to the hot-pressing direction.     

Combustion Synthesis of Si3N4–SiC Composite Powders

Fine Si₃N₄-SiC composite powders were synthesized in various SiC compositions to 46 vol% by nitriding combustion of silicon and carbon. The powders were composed of α-Si₃N₄, β-Si₃N₄, and β-SiC. The reaction analysis suggested that the SiC formation is assisted by the high reaction heat of Si nitridation. The sintered bodies consisted of uniformly dispersed grains of β-Si₃N₄, β-SiC, and a few Si₂N₂O.     

Properties of Si3N4 Produced by Nitriding Slip-Cast Si Containing Si3N4 Grog Additions

The properties of Si₃N₄ compositions produced by nitriding slip-cast Si bodies containing up to 16% Si₃N₄ grog were determined. The introduction of grog consistently lowered the densities, the room- and high-temperature strengths, and the resistance to oxidation. The open structure of the grog-containing mixes favored low-temperature gas-phase reactions leading to α-Si₃N₄ formation. In higher-density compositions containing predominantly Si, gas-liquid-solid reactions at higher temperatures produced a relatively greater content of the β phase.     

Hot-Pressing Behavior of Si3N4

The densification behavior of Si₃N₄ containing MgO was studied in detail. It was concluded that MgO forms a liquid phase (most likely a magnesium silicate). This liquid wets and allows atomic transfer of Si₃N₄. Evidence of a second-phase material between the Si₃N₄ grains was obtained through etching studies. Transformation of α- to β-Si₃N₄ during hot-pressing is not necessary for densification.     

Oxidation of Si3N4 Alloys: Relation to Phase Equilibria in the System Si3N4-SiO2-MgO

The oxidation resistance at 1400°C of silicon nitride alloys hot-pressed with magnesia was investigated as a function of the phase content of the alloys. The extent of oxidation, the products of oxidation, their stratification, and the continuity of the oxide scale are all dependent on the initial composition. Also, the compositions of the alloys themselves change during oxidation. The findings can be interpreted on the basis of compositional paths in the equivalence phase diagram. Reasons for the outward diffusion of Mg and impurities are given and the effect of the secondary phase on oxidation kinetics is discussed.     

Comparison of Tribological Behavior Between α-Sialon/Si3N4 and Si3N4/Si3N4 Sliding Pairs in Water Lubrication

We report here the study on tribological behavior of α-Sialon in aqueous medium. The results derived from a wide range of test conditions are briefly discussed. A reduction in friction coefficient from 0.7 to 0.03 and a decrease in wear rate by two orders of magnitude were achieved under low load (9.8 N) and high speed (>0.54 m/s) conditions. The tribological behavior of α-Sialon/Si₃N₄ ceramics was then compared with Si₃N₄/Si₃N₄ tribopairs.     

Microstructural Observations on Hot-Pressed Si3N4

The development of microstructure in hot-pressed Si_aN₄ was studiehd for a typical Si₃N₄ powder with and without BeSiN₂ as a densification aid. The effect of hot-pressing temperature on density, α- to β-Si₃N₄ conversion and specific surface area showed that BeSiN₂ appears to increase the mobility of the system by enhancing densification, α- to β-Si₃N₄ transformation, and grain growth at temperatures between 1450° and 1800°. These processes appear to occur in the presence of a liquid phase.     

Measurement of Interfacial Shear Strength in SiC-Fiber/Si3N4 Composites

An indentation method for measuring shar strength in brittle matrix composites was applied to SiC-fiber/Si₃N₄-matrix samples. Three methods were used to manufacture the composites: reaction bonding of a Si/SiC preform, hot-pressing, and nitrogen-overpressure sintering. An indentation technique developed by Marshall for thin specimens was used to measure the shear strength of the interface and the interfacial friction stresses. This was done by inverting the sample after the initial push through and retesting the pushed fibers. SEM observations showed that the shear strength was determined by the degree of reaction between the fiber and the matrix unless the fiber was pushed out of its (well-bonded) sheath.     

Creep Behavior of Si3N4-Whisker-Reinforced Si3N4-Matrix Composites Using an In Situ Dynamic Beam Profiling Method

A four-point flexure test, capable of simultaneously measuring load-point and beam-center displacements and permitting in situ profiling of the beam throughout the test, has been developed. Compressive and tensile strains in the outer fibers, together with the neutral axis displacement, were determined in real time for Si₃N₄-whisker-reinforced Si₃N₄-ceramic-matrix composites. Combining these data with the closed form solution of Chen and Chuang gave excellent correspondence between the creep exponents determined from flexure tests with those determined independently from tensile and compressive creep tests.     

Pressureless Sintering of Dense Si3N4 and Si3N4/SiC Composites with Nitrate Additives

The effect of aluminum and yttrium nitrate additives on the densification of monolithic Si₃N₄ and a Si₃N₄/SiC composite by pressureless sintering was compared with that of oxide additives. The surfaces of Si₃N₄ particles milled with aluminum and yttrium nitrates, which were added as methanol solutions, were coated with a different layer containing Al and Y from that of Si₃N₄ particles milled with oxide additives. Monolithic Si₃N₄ could be sintered to 94% of theoretical density (TD) at 1500°C with nitrate additives. The sintering temperature was about 100°C lower than the case with oxide additives. After pressureless sintering at 1750°C for 2 h in N₂, the bulk density of a Si₃N₄/20 wt% SiC composite reached 95% TD with nitrate additives.     

Oxidation Behavior of Hot-Pressed Si3N4

The high-temperature chemical stability of hot-pressed Si₃N₄ was studied between 600° and 1450°C. Reactions were followed by X-ray diffraction and scanning electron microscopy. In air, this material begins to oxidize at 700° to 750°C; a distinct amorphous siO₂ surface layer results after 24 h at 750°C-Concomitant formation of cristobalite occurs, depending on exposure time, and is enhanced as temperature is Increased. Magnesium and calcium magnesium silicates form above 1000°C. The data suggest that impurities, e.g. Mg, Ca, and Fe, greatly lower the oxidation resistance of Si₃N₄ in air.