Effect of polymerization mode of a dual-cured resin cement on time-dependent shear bond strength to porcelain

PURPOSE: To evaluate the shear bond strengths to porcelain and setting times of a dual-cured resin cement with light/chemical curing (dual) or chemical only curing versus time. MATERIALS AND METHODS: Variolink resin cement was bonded to specimens of etched, silanated porcelain. Groups of specimens were cured by dual cured or by chemical curing only. Shear bond strengths were recorded at 2, 3, 5, 60 minutes and 24 hours for dual cured and at 10, 20, 40, 50, 60 minutes and 24 hours for chemical-cured only after mixing. Kinetic-temperature profiles of dual and chemical curing modes of cement were calculated. RESULTS: Maximum bond strengths and time to attainment were 17.5 +/- 2.7 MPa at 60 minutes for chemical-cured and 26.1 +/- 2.3 MPa at 5 minutes for dual-cured. The peak in the kinetic-temperature setting profiles were 14.1 +/- 0.9 minutes for chemical curing and 52.2 +/- 5.2 seconds for dual curing. Dual curing provided significantly higher shear bond strengths versus chemical curing at both the 60-minute and 24-hour time periods.     

Bonding of amalgam to composite: tensile strength and morphology study

OBJECTIVES: The present study was based on the premise that it may be possible to produce useful dental restorations by bonding freshly triturated amalgam to a cured composite restoration (Group 1 specimens), or by bonding uncured composite to hardened amalgam (Group 2 specimens). METHODS: To determine the validity of this premise, a phosphonate adhesive resin cement was used to produce simulated, layered dental restorations for each test group. RESULTS: The mean tensile bond strength of 24 hour-old Group 1 specimens (6.74 MPa +/- 1.63 MPa) was almost twice that of 24 hour-old Group 2 specimens. Cohesive failure of the amalgam-substrate layer was a prominent feature of the fracture pattern of Group 1 specimens. On the other hand, rupture of all Group 2 specimens occurred mainly along the adhesive-amalgam interface. Findings from SEM examination of the layers of amalgam, adhesive cement, and resin composite of intact Group 1 specimens suggested that inclusions of adhesive resin cement may be the cause of the persistent cohesive failure of the amalgam layer. SIGNIFICANCE: It may be possible to improve the strength of bonded couples made from freshly triturated amalgam and cured resin composite by minimizing the thickness of the adhesive layer.     

Dyes for caries detection influence sound dentin bond strength

This study evaluated the influence of caries-detection dyes on the in vitro tensile bond strength of adhesive materials to sound dentin. Caries-free human molars were ground to expose superficial dentin. Two dyes (a commercial 0.5% basic fuchsin in propylene glycol and Cari-D-Tect) were applied to sound dentin and rinsed. Subsequently, the dentin was etched with phosphoric acid (35%) and rinsed, leaving a moist dentin surface. The adhesive (Prime & Bond 2.0) was applied in two layers and light cured. A composite (TPH Spectrum), a compomer (Dyract), and a hybrid ionomer (Advance) were used to prepare the bond-strength specimens with a 3-mm-in-diameter bonding area. Control groups were made without use of dyes. Six specimens were prepared for each group. After 24 hours in distilled water, tensile bond strength (MPa) was measured using a testing machine. Analysis of variance was used to evaluate the data. Without dyes, bond strengths of TPH Spectrum and Dyract with Prime and Bond 2.0 were similar and both values were significantly (P < 0.05) higher than that of Advance with Prime & Bond 2.0. Dyes for caries detection reduced the bond strength of TPH Spectrum and Dyract but not Advance when used with Prime and Bond 2.0.     

Shear bond strength required to prevent microleakage of the dentin/restoration interface

The purpose of this in vitro study was to determine the relationship between the shear bond strength [SBS] of seven dentin bonding systems to dentin and the quantitative microleakage [ML] of Class V preparations in dentin restored with these systems. The systems evaluated were All-Bond/Bisfil-P [A]; Syntac/Heliomolar [B]; XR-Bond/Herculite [C]; Scotchbond 2/Silux [D]; Denthesive/Charisma [E]; Prisma Universal Bond 2/Prisma AP.H [F]; and Tenure/Perfection [G]. The 115 specimens were removed from the assembly apparatus and stored in saline at 37 degrees C for 24 hours, the SBS determined and expressed in MPa. Fifteen Class V preparations in dentin were restored with each of the bonding systems, thermocycled 500x in 2% methylene blue solution between 50 degrees C and 8 degrees C, and the ML determined by means of a spectrophotometric dye-recovery method. The ML was expressed in microgram dye/restoration. The data were analyzed by ANOVA, Student-Newman-Keuls test, and linear regression analysis. The SBS in MPa were: A:17.2 +/- 3.6; B:15.9 +/- 2.1; C:15.4 +/- 3.7; D:11.6 +/- 2.2; E:10.7 +/- 3.7; F:10.4 +/- 2.5; G:8.2 +/- 3.9. The ML in microgram dye/restoration were: A:2.6 +/- 1.2; B:2.6 +/- 1.0; C:2.2 +/- 1.9; D:3.1 +/- 2.9; E:4.6 +/- 4.2; F:2.6 +/- 2.5; G:4.4 +/- 4.1. SBS = 20.91-2.60 [microgram dye]. The results suggest that a SBS of +/- 21 MPa may reduce ML to near zero.     

Anterior cruciate ligament graft fixation. Initial comparison of patellar tendon and semitendinosus autografts in young fresh cadavers

The initial biomechanical properties of semitendinosus and patellar tendon autografts and their fixation strengths were investigated. Twenty fresh cadaveric knees from donors under 42 years of age were used in the study. After removing all soft tissues other than the anterior cruciate ligament, we determined the ultimate tensile strength (2195 +/- 427 N) and stiffness (306 +/- 80 N/mm) of the anterior cruciate ligament in nine knees. In six knees, anterior cruciate ligaments were reconstructed using an autologous patellar tendon graft with proximal and distal interference fit screws; this resulted in an ultimate tensile strength of 416 +/- 66 N. Five knees were reconstructed with quadruple-stranded (double-looped) semitendinosus tendons fixed proximally by a titanium button and braided tape and distally by tibial post screw. This resulted in an ultimate tensile strength of 612 +/- 73 N, which was significantly higher than the strength in the patellar tendon group. Graft stiffness did not differ between the groups and was 47 +/- 19 N/mm (N = 11). This study demonstrates that the reconstructed knees had only 20% to 30% of the ultimate tensile strength of the normal anterior cruciate ligament. In summary, the semitendinosus reconstruction using a button for proximal fixation is, at the time of surgery, approximately 50% stronger than patellar tendon reconstructions with similar stiffness.     

Precision of fit: the Procera AllCeram crown

STATEMENT OF PROBLEM: Strength, color stability, and precision of fit are requirements for all-ceramic restorations. The Procera AllCeram crown system, composed of a densely sintered high-purity alumina core combined with a low fusing surface porcelain, appears to satisfy most of these requirements. However, evaluation of marginal fit has not been reported. PURPOSE: This study measured the precision of fit of the Procera AllCeram crown fabricated with Procera CAD/CAM technology for the premolar and molar teeth fit to a die. MATERIAL AND METHODS: Five ivorine maxillary first premolars and first molars were prepared for full-coverage crowns. Preparations were standardized with a convergence angle of 10 degrees, chamfer margins of 1.3 to 1.5 mm circumferentially, and occlusal reduction of 2.0 mm. AllCeram crowns were fabricated for the dies, and the fit of the crown to the die was determined by using a standardized procedure with a silicone impression material that served a dual role: (1) as a retrievable luting agent, and (2) to replicate the internal aspects of the crown. Laser videography was used to measure the gap dimension between the crowns and the dies at the marginal opening, the axial wall, the cusp tip, and the occlusal adaptation measurement locations. Mean gap dimensions and standard deviations (SDs) were calculated for marginal opening, internal adaptation, and precision of fit. RESULTS: Mean gap dimensions and standard deviations at the marginal opening for the premolar and molar crowns were 56.0 microns SD +/- 21 and 63.0 microns SD +/- 13 microns, respectively. The mean gap dimensions and SDs of the internal adaptation were 69.0 microns SD +/- 17 microns for axial wall, 48.0 microns SD +/- 12 microns for cusp tip, and 36.0 microns SD +/- 7 microns for occlusal adaptation for the premolar crowns; and 49.0 microns SD +/- 3 microns axial wall, 67.0 microns SD +/- 21 microns cusp tip, and 74.0 microns SD +/- 29 microns occlusal adaptation for molar crowns. Precision of fit and SDs for premolar and molar crowns were 52.0 microns SD +/- 19 microns and 63.0 microns SD +/- 20 microns, respectively. Mean marginal openings and precision of fit gap dimensions for the crown groups were not significantly different at the .05 level. However, gap dimensions that defined the internal adaptation at the measurement locations were different (P < or = .05). CONCLUSION: Mean gap dimensions for marginal openings, internal adaptation, and precision of fit for the crown groups were below 70 microns. These findings show that the crowns studied can be prescribed with confidence knowing that the precision of fit will consistently be less than 70 microns.     

Changes in esophageal function after vertical banded gastroplasty as demonstrated by esophageal scintigraphy

STATEMENT OF PROBLEM: Earlier studies on orthodontic brackets have shown a loss of bond strength after a sonic toothbrush was used. PURPOSE: This in vitro study evaluated the difference in bond strength of single complete veneer crowns after being subjected to the equivalent of 2 years of brushing with sonic and counterrotational toothbrushes. MATERIAL AND METHODS: Complete gold crowns were fabricated with a conventional indirect technique for 30 extracted, intact, prepared human premolar teeth. Castings were then luted to the teeth with glass ionomer cement. Teeth were randomly divided into 3 groups of 10 teeth each, 1 group to be brushed with Sonicare sonic toothbrush, 1 group to be brushed with Interplak counterrotational mechanical toothbrush, and 1 group as the control. Groups 1 and 2 were then brushed for the equivalent of 2 years per tooth. A uniform force of 50 g for the sonic toothbrush and 120 g for the counterrotational toothbrush was used. Control specimens were not brushed. Brush heads and sample teeth in contact with the toothbrush were kept moist at all times. Tensile dislodgment force was determined with an Instron universal testing machine. RESULTS: The castings brushed with a sonic toothbrush required a mean of 43.22 kg (+/- 11.16) force to remove the crowns from the teeth, whereas the counterrotational group required a mean of 42.87 kg (+/- 10.42) and the control group a mean of 42.12 kg (+/- 6.61). Analysis of variance on the force data indicated no differences among the 3 groups in the force needed to remove the castings (F[2,24] = 0.031, P = .97). CONCLUSION: This in vitro study demonstrated no significant differences between groups in the amount of tensile dislodgment force required to remove cemented full veneer crowns from prepared teeth after brushing for the equivalent of 2 years time with a sonic toothbrush or a counterrotational toothbrush.     

Shear bond strength of orthodontic brackets cemented with a zinc oxide-polyvinyl cement

The purpose of this study was to compare the shear bond strengths and enamel surface structure after debonding a conventional metal bracket and a polycrystalline ceramic bracket bonded with a bipolar zinc oxide-polyvinyl cement (F-21) or a light-cured resin cement (Transbond). Forty extracted human premolars were used. The buccal enamel surfaces were used, and the teeth randomly divided into four groups of 10 teeth each: group 1: conventional metal bracket (Unitek) bonded with Transbond; group 2: metal bracket bonded with F-21; group 3: ceramic bracket (Transcend 2000) bonded with Transbond; and group 4: ceramic bracket bonded with F-21. The brackets were bonded to the etched enamel surfaces according to manufacturer's instructions. All specimens were stored in distilled water for 24 hours and then thermocycled for 300 cycles between 5 degrees C and 55 degrees C. The specimens were mounted in dental stone and placed in the Instron at a crosshead speed of 0.5 mm/min with a knife-edged blade. Immediately after debonding, the enamel surface and bracket-enamel interface were evaluated visually and with a stereomicroscope. Representative samples were then examined with the scanning electron microscope. The analysis of variance and Student-Newman-Keuls tests were performed. The results in megapascals were Group 1: 19,6 (+/- 9,6); group 2: 14,3 (+/- 4,6); group 3: 28,8 (+/- 12,6); and group 4: 18,5 (+/- 7,5). Group 3 was statistically significantly different (P < 0.008) from all other groups. Groups 1, 2, and 4 were not significantly different.(ABSTRACT TRUNCATED AT 250 WORDS)     

Coronary angioplasty, bypass surgery, and retransplantation in cardiac transplant patients with graft coronary disease

BACKGROUND AND OBJECTIVE: Prior studies of laser tissue soldering (LTS) of epithelial skin have shown poor wound strength in the short-term; however, we hypothesize that greater tensile strength and healing properties will result from directing laser energy to the dermal aspect of the skin. The current study compares wound strength and histology in a rat skin flap model of epithelial and dermally applied LTS. STUDY DESIGN/MATERIALS AND METHODS: Skin flaps (2.5 x 4 cm) were raised and bisected on the dorsum of Sprague-Dawley rats. The center line of bisection was closed from a dermal approach by LTS (LTS-D, diode laser 15.9 W/cm2 + Columbia solder), the upper incision by epithelial LTS (LTS-E), and the lower incision by suturing (7-0 Vicryl). Wound skin strips (1-2 mm x 10 mm) were studied immediately (N = 14) and at 3 (N = 57), 7 (N = 31), and 10 (N = 28) days postoperatively and were subjected to tensiometric analysis. Histologic staining with hematoxylin and eosin and Mallory's trichrome methods were used to define wound architecture. RESULTS: No wound dehiscences were noted in any group. Greater immediate tensile strength was noted in wounds closed by LTS-D (521 +/- 61 g/cm2) versus LTS-E (342 +/- 65 g/cm2); however, this difference was not statistically significant (P = .08). By 3 days, both LTS-D (476 +/- 55 g/cm2) and LTS-E (205 +/- 37 g/cm2) maintained their initial strength; however, LTS-D and sutured (436 +/- 49 g/cm2) wounds were stronger (P < .05) than LTS-E. At 7 and 10 days, LTS-D (2,433 +/- 346 g/cm2 and 3,100 +/- 390 g/cm2) showed superior tensile strength (P < .05) compared to both LTS-E (1,542 +/- 128 g/cm2 and 2,081 +/- 219 g/cm2) and suturing (1,342 +/- 119 g/cm2 and 1,661 +/- 115 g/cm2). Histologic analysis of LTS-D wounds at 3 days showed full-thickness tissue apposition, complete epithelialization, and minimal inflammation or thermal injury. At 7 days, solder was present in the wounds. In contrast, LTS-E wounds at 3 days displayed lack of epithelialization secondary to thermal injury and partial-thickness tissue apposition. However by 7 days, epithelialization was complete with moderate scarring, and no solder was seen. Sutured samples appeared similar to LTS-D, except for poorer tissue apposition at the hypodermis. CONCLUSION: Our results show that skin flap wound healing after dermal LTS is superior to epithelial LTS and emphasizes the importance of site specificity in the utilization of this operative technique in reconstructive surgery.     

24-hour shear bond strength of metal orthodontic brackets bonded to porcelain using various adhesion promoters

Clinically, orthodontists are often faced with the difficulties of bonding to porcelain crowns, veneers, or bridges. Traditional methods of dealing with this are often time-consuming and generally esthetically unacceptable to patients. Current interest involves the use of organosilane primers with or without NTG-GMA and BPDM resins to aid in chemically bonding porcelain with traditional orthodontic adhesives. This study compared the bond strength of three types of adhesion promoters: Ormco Porcelain Primer (OR) (Ormco Corp., Glendora, Calif.), All-Bond2 (AB2) (Bisco Dental Products, Inc., Itasca, Ill.), and Scotchprime Ceramic Primer (SP) (3M, St. Paul, Minn.) with two orthodontic adhesives: Phase II (Reliance, Inc., Itasca, Ill.) and Rely-a-bond (Reliance, Inc., Itasca, Ill.). Eighty ceramometal samples were fabricated and hydrated for 1 week in distilled water before bonding. Next, the samples were etched with 2.5 % HF acid for 90 seconds, rinsed and upper central incisor metal orthodontic brackets were bonded with the various primers and adhesives. After 24 hours they were sheared off with an MTS machine at at rate of 0.5 mm/min, and the bond strength was measured. The mean shear bond strengths (MPa) with Phase II were as follows; Control 0.44 (sigma = 0.22), AB2 8.40 (sigma = 3.61), OR 13.31 (sigma = 5.79), SP 13.53 (sigma = 3.34). With Rely-a-bond, the shear bond strengths were Control 0.41 (sigma = 0.67), AB2 4.34 (sigma = 1.88), OR 9.73 (sigma = 4.58), and SP 12.40 (sigma = 3.05).(ABSTRACT TRUNCATED AT 250 WORDS)     

Residual monomer/additive release and variability in cytotoxicity of light-curing glass-ionomer cements and compomers

In previous studies, light-cured glass-ionomer cements have been shown to evoke cytotoxic reactions. It was the purpose of this investigation (a) to determine the nature of the ingredients released into an aqueous medium from 2 light-cured glass-ionomer cements (GICs) and 3 compomers; (b) to evaluate the cytotoxicity of these extracts; and (c) to correlate the extent of the cytotoxic effects with eluted substances. Specimens of 2 light-cured GICs and 3 compomers were prepared and extracted in distilled water or cell culture medium for 24 hrs (surface-liquid ratio 42.4 mm2/mL). The aqueous eluates were analyzed by gas chromatography/mass spectrometry (GC/MS). The relative amounts of the components released from various products were compared by means of an internal caffeine standard [%CF]. For evaluation of cytotoxic effects, permanent 3T3 fibroblasts were incubated with medium extracts for 24 hrs. In addition, the ED50 concentration of the photoinitiator diphenyliodoniumchloride (DPICl) was determined. In all extracts, several water-elutable organic substances were found: (Co)monomers (especially HEMA and ethylene glycol compounds), additives (e.g., camphorquinone and diphenyliodoniumchloride), and decomposition products. The extracts of 3 products inhibited cell growth only moderately, whereas the light-cured GIC Vitrebond and the compomer Dyract Cem revealed severe cytotoxic effects. Vitrebond liberated the initiator DPICl, whereas Dyract Cem segregated a relatively high quantity [2966 %CF] of the comonomer TEGDMA in comparison with the other products. The present data show that TEGDMA and DPICl may be regarded as the prime causes for cytotoxic reactions evoked by the investigated light-cured glass-ionomer cements or compomers. Therefore, leaching of these substances should be minimized or prevented.     

Imbrication versus excision for fascial healing

BACKGROUND: The purpose of this study was to determine whether imbrication of native fascia versus excision and closure of new raw fascia forms a stronger union. METHODS: We utilized the anterior rectus sheath fascia of Sprague-Dawley rats as the model. Sixty rats underwent fascial tightening procedures. Each rat had the anterior rectus sheath shortened by 1 cm, 30 by imbrication and 30 by excision and closure. Ten of each group were harvested at 7 days' healing, 10 at 14 days, and 10 of each group at 28 days' healing. The anterior rectus sheath was removed, a "dumbbell" shape constructed, and the cross sectional area at the point of interest determined. The fascia was placed on an Instron tensiometer to determine the breaking strength. Tensile strength was calculated and the data analyzed by ANOVA and the Kruskall-Wallis test. Tissue samples of the closures were histologically analyzed for fibroblast counts, degree of inflammation, and presence of dense fibrous connective tissue. Tissue samples were also analyzed for enzymatic collagen crosslinking. RESULTS: There was a statistically significant difference in tensile strength between the two groups at 7, 14, and 28 days. Results show that at 7 days the mean tensile strength of excision was 0.133 kg/mm2 +/- 0.056 and the mean tensile strength of imbrication was 0.083 kg/mm2 +/- .048 (P < 0.05); at 14 days the mean tensile strength of excision was 0.105 kg/mm2 +/- 0.033 and the mean tensile strength of imbrication was 0.057 kg/mm2 +/- 0.014 (P < 0.002), and at 28 days the mean tensile strength of excision was 0.279 kg/mm2 +/- 0.143 and the mean tensile strength of imbrication was 0.145 kg/mm2 +/- 0.061 (P < 0.03). Histologic findings showed no statistical significance between the two closure methods when comparing degree of inflammation or the number of fibroblasts present. However, at 7 and 14 days there is a significantly greater presence of dense fibrous connective tissue in the excision group (P < 0.03 at 7 days and P < 0.044 at 14 days by ANOVA). Collagen crosslink analysis showed that by day 28 there is a significantly greater amount (P < 0.05 by ANOVA) of the difunctional crosslink dihydroxylysinonorleucine (DHLNL) and a greater ratio between DHLNL and the difunctional crosslink hydroxylysinonorleucine (HLNL) in the excision and closure group. CONCLUSION: We conclude that at 7, 14, and 28 days healing, excision provides a significantly stronger closure than imbrication. According to the crosslinking analysis, it is likely that this strength advantage may continue to increase over time. These findings suggest that excision and closure may be the preferred method for fascial tightening procedures.     

The influence of the depth of substrate dentin surface and thickness of the current restorative samples on bond strength

The effect of sample thickness and dentin depth on bond strength of composite, compomer and resin modified glass ionomer have been investigated. The occlusal surfaces of 84 non carious human third molars were used for bonding. 4 subgroups were tested, superficial dentin with sample thickness 1 and 2 mm and deep dentin with sample thickness 1 and 2 mm respectively SBMP + /Z 100 composite showed 26 +/- 3.2, 22.3 +/- 4.5, 17 +/- 3.2 and 21.8 +/- 4.2 MPa shear bond strength to S. dentin 1 mm, deep dentin 1 and 2 mm and S. dentin 2 mm respectively. Compoglass reported 10.4 +/- 1.57, 9.1 +/- 2.3, 5.0 +/- 0.6 and 9.24 +/- 3.1 MPa while, Vitremer achieved 4.7 +/- 0.49, 3.2 +/- 0.39, 3.0 +/- 0.81 and 3.2 +/- 0.53 MPa. It is concluded that the highest bond strength can be achieved to superficial dentin in thickness or increments not more than 1 mm. And that both dentin depth and sample thickness might influence the quality of the bond to dentin with an effect that varies from one material to another depending upon the mechanism of bond of each material and its chemical composition.     

Bone bonding ability of bioactive bone cements

The bone bonding ability of three types of bioactive bone cement A, B, and C consisting of glass or glass ceramic powder and bisphenol-alpha-glycidyl methacrylate resin was evaluated. Type A contained MgO-CaO-SiO2-P2O5-CaF2 glass powder; Type B, MgO-CaO-SiO2-P2O5-CaF2 glass ceramic powder; and Type C, MgO free CaO-SiO2-P2O5-CaF2 glass powder. Rectangular plates (2 x 10 x 15 mm) of Types A, B, C, and polymethylmethacrylate cements were implanted into the tibial metaphyses of male rabbits and the failure load measured by mechanical failure testing (detaching test) 10 and 25 weeks after implantation. The failure loads of Types A, B, C, and polymethylmethacrylate cements were respectively, 29.52, 41.48, 28.22, and 0.29 N at 10 weeks and 33.42, 41.27, 33.64, and 0.20 N at 25 weeks. Examination of the bone cement interface revealed that all the bioactive bone cements achieved direct bone contact with the bone. These results showed that all three types of bioactive bone cement have the ability to bond to bone, and the cement containing glass ceramic powder revealed higher bonding strength than did those containing glass powder.     

Dentastic bond strength to dentin

PURPOSE: To evaluate the shear bond strength to the dentin of permanent teeth and failure site of Dentastic hydrophilic dentin bonding agent. MATERIALS AND METHODS: Forty permanent noncarious molar teeth stored in distilled water were obtained. The teeth were cleaned with pumice and a rubber cup. The mesio-buccal surface of the teeth was ground flat with hand pressure with a series of SiC paper ending with the 600 grit to provide a uniform surface on dentin to which the resin composite could be applied. After preparing the tooth surface, the teeth were stored in distilled water for 48 hours. They were then divided at random into four groups of 10 specimens each: Group 1: Dentastic, five coats of primer; Group 2: Dentastic, three coats of primer; Group 3: Dentastic, five coats of primer, light-cured adhesive before resin bonding; Group 4: Dentastic, three coats of primer, light-cured adhesive before resin bonding. All specimens were thermocycled (500x) and sheared in a testing machine. After shear testing, the debonded sites of all samples were examined with a stereomicroscope and a scanning electron microscope. RESULTS: The results in MPa were: Group 1: 22.63 +/- 6.24; Group 2: 23.35 +/- 5.14; Group 3: 23.58 +/- 5.66; Group 4: 27.26 +/- 8.22. ANOVA and Student-Newman-Keuls showed no statistically significant difference between the groups. In all groups, all specimens failed at the dentin (dentin cohesive failure = dentin fracture) or at the resin (resin cohesive failure = resin fracture). This means that the bond strength of the product is stronger than the cohesive strengths of the dentin and the resin.     

Relationship between haemodynamics and morphology in pulmonary hypertension. A quantitative intravascular ultrasound study

BACKGROUND: Intravascular ultrasound imaging of the pulmonary arteries has been demonstrated to be a reliable method of quantifying vessel diameter, luminal area and pulsatility. Simultaneous measurement of flow velocity and its response to vasodilators allows the relationship between morphology and functional compromise to be studied, especially endothelial dysfunction. METHODS: In 51 patients (mean age = 49.8 +/- 12.6 years, 17 female) we performed right heart catheterization and simultaneous intravascular ultrasound of pulmonary artery branches. The patients were divided in two groups: group 1 with normal pulmonary artery pressure and pulmonary vascular resistance, and group 2 with pulmonary hypertension (peak pulmonary artery pressure > 30 mmHg and/or mean pulmonary artery pressure > 20 mmHg). Vessel wall and lumen were studied using a 2.9 F intravascular ultrasound catheter with a 30 MHz phased array transducer. Measurement of blood flow velocity was accomplished by a Doppler flow wire (0.018 inch). The maximal flow change during acetylcholine infusion (adjusted to 10(-6); 10(-5), and 10(-4) M concentration in the blood vessel) was measured. RESULTS: There were no significant differences between groups 1 and 2 with respect to age (48.5 +/- 14.3 years vs 50.3 +/- 12.3 years; P = ns), gender (4 female/8 male vs 13 female/26 male; P = ns), luminal area of the vessel segment in which the intravascular ultrasound measurements were obtained (11.8 +/- 6.1 mm2 vs 16.7 +/- 14.3 mm2; P = ns), internal diameter (3.9 +/- 1.2 mm vs 4.2 +/- 1.7 mm; P = ns), and external diameter (6.1 +/- 1.3 mm vs 6.9 +/- 2.1 mm; P = ns). Cross-sectional images of the pulmonary artery wall demonstrated a single ring with high echodensity with a thin inner layer regarded as intima in group 1. In contrast, the majority of patients (n = 35/39) in group 2 demonstrated a thickening of the intimal layer and/or a disturbance of layering of the echogenic arterial wall. The relative wall thickness was higher in group 2 than in group 1 (22.5 +/- 10.4% vs 15.3 +/- 6.5%; P < 0.05). There were no significant correlations between pulmonary artery pressure and wall thickness pulmonary artery pressure and area change in the cardiac cycle, acetylcholine-dependent increase in pulmonary flow and morphological changes in the vessel wall. CONCLUSION: We conclude that intravascular ultrasound is capable of detecting morphological changes in the pulmonary vessel wall in pulmonary hypertension and that vessel wall hypertrophy of small pulmonary segment arteries, as detected by intravascular ultrasound, is not predictive of functional vasodilatory response of resistance vessels of the same vessel area.     

Mechanical characterization of a totally intramedullary gradual elongation nail

An intramedullary gradual elongation nail (Albizzia) capable of fulfilling the function of traditional intramedullary nails while providing the gradual, controlled distraction of an external fixator was designed for progressive lengthening of lower limbs. In this study, the biomechanics of the gradual elongation nail were compared with several intramedullary nails: Grosse & Kempf, Russell-Taylor, AO, and Laffay. Bending stiffness, torsional stiffness, ultimate bending strength, and torsional strength were determined using the American Society for Testing and Materials standard F383-73 as a guide. The results show that in unextended and elongated conditions, the gradual elongation nail has torsional stiffness (1-5 Nm2) comparable with the AO nail (2 Nm2) and bending stiffness (41-89 Nm2), ultimate bending (246 Nm), and torsional (28-37 Nm) strengths within the ranges obtained for other intramedullary nails (27-105 Nm2, 167-298 Nm, and 2-100 Nm, respectively). Additionally, the low torque required to lengthen the device under a 500 N load (3 Nm) and the low longitudinal stiffness because of the active dynamization system with bimodal load deformation characteristics (80-120 N/mm initial, 600-800 N/mm secondary) produce a device with almost no torsional and longitudinal stress shielding. From a biomechanical point of view, this single, completely implantable device is a safe, viable, and efficacious alternative to external fixation for progressive lengthening of lower limbs.     

Truncal duplication: a case report

The mechanical properties of fascia lata in the form of a sheet and as a tubulised structure have been determined. The stiffness of the sheet was 3.3 +/- 0.58 N/mm and the stiffness of the tube was 6.2 +/- 1.06 N/mm. The ultimate tensile strength of the tube was 35.7 +/- 14.1 N.     

Retention of paraposts cemented with dentin-bonded resin cements

The main purpose of this study was to assess the retention of Paraposts cemented with dentin-bonded resin cements in single-rooted teeth with elliptical canals. Forty-two mandibular premolars and canines were used in this study. The crowns of these teeth were removed 1 mm above the cementoenamel junction and the root canals instrumented to a depth of 8 mm to receive size 5 Paraposts. Prepared teeth were divided into six equal groups. Each group was assigned to a different cementation system at random. The six cementation systems used were: Fleck's Cement, Universal Post Cementation Kit, Prisma Universal Bond 3/Biomer, Scotchbond 2/Resiment, All-Bond 2/All-Bond C & B Cement, and Scotchbond Multi-Purpose/Resiment. Following post cementation, the teeth were stored in water at 37 degrees C for 24 hours, after which the posts were subjected to uniaxial tensile force on a testing machine until post separation occurred. Paraposts cemented with Prisma Universal Bone 3/Biomer or with Scotchbond Multi-Purpose/Resiment had significantly greater separation forces than posts cemented with any of the other cementation systems. Adhesive failure of the posts occurred in all of the specimens of the resin cement groups, whereas cohesive failure of the cement occurred in the majority of the specimens of the zinc phosphate cement group. The effects of thermocycling and post length (5 mm versus 8 mm) on the retention of Paraposts cemented with dentin-bonded resin cements were also investigated. Neither thermocycling nor post length had a significant effect on post separation force.     

Efficacy of exogenous fibronectin in wound healing in malnourished rats

BACKGROUND/PURPOSE: Fibronectin (FN) plays an important role in fibrin matrix formation during the wound healing process. The authors investigated whether exogenous FN increases the bursting strength (BS) of surgical wounds in malnourished rats. METHODS: Ninety rats were grouped according to three nutritional conditions (n = 30 in each group). All animals underwent a transverse celiotomy after 3 weeks of feeding, and FN (2 mg/body/day) was given postoperatively to 15 rats in each of the three groups. Wound BS was measured on postoperative days (PODs) 3, 5, and 7 after removal of the sutures. RESULTS: BS in normally nourished rats (group N; 142.6+/-23.4 mmHg) was significantly higher than that in protein malnourished rats (group PM, 110.2+/-11.2 mm Hg) and protein/ calorie (Cal)-malnourished rats (group PCM, 76.5+/-10.7 mm Hg) on POD 7 (P<.01). However, BS values for groups PM + FN (147.0+/-21.1 mmHg) and PCM + FN (115.1+/-28.9 mm Hg) were intensified significantly in comparison with groups PM and PCM (P<.01). Plasma FN levels in rats of the three FN nontreated groups were similarly decreased on POD 3 or 5, but returned to the preoperative level on POD 7, whereas those for the other three FN-treated groups increased after POD 3. CONCLUSION: Intravenous administration of FN might strengthen the weakened wounds of malnourished animals.