聚(3-羟基丁酸酯-co-4-羟基丁酸酯)/二氧化钛纤维的成纤性能

用不同含量的二氧化钛(TiO2)改性聚(3-羟基丁酸酯-co-4-羟基丁酸酯)[P(3HB-co-4HB)],并进行了纺丝研究。采用毛细管流变仪、热重分析仪、单丝强力仪测试了P(3HB-co-4HB)/TiO2复合材料的流变性能、热性能、单丝力学性能和回弹性。实验结果表明,P(3HB-co-4HB)和P(3HB-co-4HB)/TiO2为假塑性流体,TiO2可以有效改善材料的加工流动性;提高材料的热稳定性;TiO2的加入使纤维的断裂强度降低;但纤维的弹性恢复率可达100%,退绕性有所改善。     

GF/P(3HB-co-4HB)-PLA生物基复合材料的制备与性能

为了提高聚（3-羟基丁酸酯-co-4 羟基丁酸酯）-聚乳酸（P（3HB-co-4HB）-PLA）生物基共混材料的力学性能和尺寸稳定性,扩大应用领域,以P（3HB-co-4HB）和PLA共混物为基体,盐酸或偶联剂表面处理的玻璃纤维（GF）为增强材料,采用熔融共混法制备GF/P（3HB-co-4HB）-PLA复合材料。通过傅里叶变换红外光谱仪（FTIR）、扫描电子显微镜（SEM）、热失重分析仪（TGA）和万能电子拉力机等研究了GF表面处理方法对复合材料力学性能、热性能、尺寸稳定性及断面形态的影响。研究结果表明：表面改性GF的加入可显著提高P（3HB-co-4HB）-PLA共混材料的综合性能。经偶联剂表面接枝的GF可均匀分散在P（3HB-co-4HB）-PLA基体中并形成较强的界面结合。添加质量分数20%的偶联剂改性GF使复合材料的拉伸强度、弯曲强度、缺口冲击强度和硬度分别提高了29.38%、20.32%、41.38%和15.31%;初始热分解温度（IDT）和维卡软化温度（VST）分别提高了6.64 ℃和10.7 ℃;室温和60 ℃放置60 d后复合材料试样长度方向的尺寸稳定性分别提高了32.47%和33.70%。     

成核剂对聚(3-羟基丁酸酯-co-4羟基丁酸酯)性能的影响

分别以氮化硼(BN)、BRUGGOLENP250、CaCO3和Tm-3为成核剂,用熔融模压法制备了聚(3-羟基丁酸酯-co-4羟基丁酸酯)[P(3HB-co-4HB)]样品,借用偏光显微镜(POM)、差示扫描量热(DSC)、热重分析(TGA)和扫描电镜(SEM)等考察了成核剂种类及用量对P(3HB-co-4HB)结晶形态、熔点、热分解温度、力学性能及断面形态的影响。结果表明,各种成核剂均能有效细化P(3HB-co-4HB)的球晶尺寸,提高其熔点及热分解温度;当成核剂BN的质量分数为5‰~8‰时,P(3HB-co-4HB)的综合性能最好。     

扩链改性对聚(3-羟基丁酸酯-co-4-羟基丁酸酯)性能的影响

以多苯基多亚甲基多异氰酸酯(PAPI)为扩链剂,采用熔融共混法扩链改性聚(3-羟基丁酸酯-co-4-羟基丁酸酯)[P(3HB-co-4HB)]。使用凝胶渗透色谱、热失重分析仪、电子拉力机、毛细管流变仪、旋转流变仪等研究了PAPI添加量对P(3HB-co-4HB)的相对分子质量、热稳定性、力学性能以及流变性能的影响。结果表明,PAPI的使用能够提高P(3HB-co-4HB)的相对分子质量和熔体黏度,并能有效改善P(3HB-co-4HB)的热稳定性和力学性能,成功实现了对P(3HB-co-4HB)的扩链改性。PAPI的添加量为2.0phr时,体系综合性能最佳,其起始分解温度和最大分解温度分别比纯P(3HB-co-4HB)提高了16.7℃和11.4℃,其拉伸强度和断裂伸长率分别比纯P(3HB-co-4HB)提高了21%和218%。     

扩链改性对聚(3-羟基丁酸酯-co-4-羟基丁酸酯)性能的影响EI北大核心CSCD

以多苯基多亚甲基多异氰酸酯(PAPI)为扩链剂,采用熔融共混法扩链改性聚(3-羟基丁酸酯-co-4-羟基丁酸酯)[P(3HB-co-4HB)]。使用凝胶渗透色谱、热失重分析仪、电子拉力机、毛细管流变仪、旋转流变仪等研究了PAPI添加量对P(3HB-co-4HB)的相对分子质量、热稳定性、力学性能以及流变性能的影响。结果表明,PAPI的使用能够提高P(3HB-co-4HB)的相对分子质量和熔体黏度,并能有效改善P(3HB-co-4HB)的热稳定性和力学性能,成功实现了对P(3HB-co-4HB)的扩链改性。PAPI的添加量为2.0phr时,体系综合性能最佳,其起始分解温度和最大分解温度分别比纯P(3HB-co-4HB)提高了16.7℃和11.4℃,其拉伸强度和断裂伸长率分别比纯P(3HB-co-4HB)提高了21%和218%。     

改性纳米二氧化硅/聚己内酯/聚(3-羟基丁酸酯-co-4-羟基丁酸酯)的结构与性能研究

利用异丙基三(二辛基焦磷酸酰氧基)钛酸酯偶联剂改性纳米二氧化硅,采用熔融共混挤出法制备聚己内酯(PCL)/聚(3-羟基丁酸酯-co-4-羟基丁酸酯)(P(3HB-co-4HB))/改性纳米二氧化硅(nano-SiO2)复合降解材料;利用红外光谱(FIIR)、万能拉力机、扫描电镜(SEM)、动态力学分析仪(DMA)等研究了改性nano-SiO2对复合材料的表面结构、力学性能等性能的影响。结果表明:改性nano-SiO2含量为4%时,复合降解材料的力学性能有明显的改善;少量添加的改性nano-SiO2可以均匀分散在PCL/P(3HB-co-4HB)基体树脂中,但当加入量过大时,容易发生团聚现象。     

聚丁二酸丁二酯/聚(3-羟基丁酸酯-co-4-羟基丁酸酯)/纳米高岭土熔融共混力学性能、流变及降解行为研究

用熔融共混挤出法制备的聚丁二酸丁二酯(PBS)/聚(3-羟基丁酸酯-co-4-羟基丁酸酯)[poly(3HB-co-4HB)]/纳米高岭土(nano Kaolin)复合降解材料;利用万能拉力机、旋转流变仪和SEM对其力学性能、流变行为、微观结构及降解性能进行研究。结果表明,PBS/poly(3HB-co-4HB)/nano Kaolin(100/10/8)复合降解材料的缺口冲击强度、断裂伸长率达到最大,此后随着nano Kaolin质量百分比增加,而呈下降趋势;在室外自然条件下,经过土埋一段时间后的降解实验,PBS/poly(3HB-co-4HB)/nano Kaolin(100/10/12)复合材料发生了明显的降解,复合降解材料的失重率也已经降到64%左右,说明材料的降解性能较好;纳米复合降解材料熔融剪切储能模量(G′),剪切损耗模量(G″)随着频率的增大呈单增趋势。     

静电纺丝制备P(3HB-co-4HB)/醋酸纤维素复合纳米纤维支架的性能及细胞相容性

采用静电纺丝法制备了一系列不同组成含量的3-羟基丁酸-4-羟基丁酸共聚物(P(3HB-co-4HB))/醋酸纤维素(CA)复合纳米纤维支架。通过扫描电镜、水相接触角和力学性能测试对复合纳米纤维支架的形貌、亲水性及力学性能进行了表征。结果表明,静电纺P(3HB-co-4HB)/CA复合纳米纤维均匀,平均直径在350~700nm之间,且呈相互贯通的三维多孔网状结构。随着CA含量的增加,复合纳米纤维支架的亲水性变好,但拉伸强度和断裂伸长率有所下降。体外降解实验发现,不同降解环境下P(3HB-co-4HB)/CA复合纳米纤维支架的降解速率不同,酶能加速复合纳米纤维支架的降解速率。鼠成纤细胞在复合纳米纤维支架表面能很好地粘附和铺展,表明P(3HB-co-4HB)/CA复合纳米纤维支架具有良好的细胞相容性,在组织工程支架材料领域具有广阔的应用前景。     

聚丁二酸丁二醇酯/聚羟基烷酸酯熔融共混物的结晶及流变力学行为

用熔融共混法制备聚丁二酸丁二醇酯(PBS)/聚(3-羟基丁酸酯-co-4-羟基丁酸酯)[Poly(3HB-co-4HB)]复合降解材料,利用差示扫描量热(DSC)、旋转流变仪及万能拉力机对其结晶、流变行为及力学性能进行研究。结果表明,在PBS中加入Poly(3HB-co-4HB)后,发现结晶起始温度(To,c)、结晶峰温度(Tp,c)以及结晶结束温度(Te,c)有所提高,结晶度随着Poly(3HB-co-4HB)的增加呈先增大后下降的趋势;PBS/Poly(3HB-co-4HB)复合降解材料随着Poly(3HB-co-4HB)添加量的增大,断裂伸长率和拉伸强度却呈下降趋势;同时剪切储能模量(G′)、剪切损耗模量(G″)呈现出单增趋势。因此,在复合降解材料中添加适量的Poly(3HB-co-4HB)能改善PBS的结晶、流变及力学行为。     

4-羟基丁酸含量对聚 3-羟基丁酸 与 4-羟基丁酸共聚物性能和结构的影响

目的对3-羟基丁酸4-羟基丁酸共聚酯P(3HB-co-4HB)进行酶解测试。方法通过力学性能测试、失重率分析、热失重分析、X-射线衍射分析、扫描电镜等测试和表征手段对样品的物理性能及生物降解情况进行评价。结果 P(3HB-co-4HB)分子中4HB单体(文中均用摩尔分数表示)的引入提高了材料的柔韧性,材料的脆性下降;失重率方面,4种材料的降解速率从高到低依次为P(3HB)P(3HB-co-5%4HB)(3HB-co-10%4HB)P(3HB-co-15%4HB);酶解前期,材料的热稳定性增强,而酶解后期材料的热稳定性逐渐下降;XRD结果表明材料降解过程中结晶度的变化不明显;P(3HB-co-4HB)分子中随着4HB单体含量的增加,材料表面粗糙度降低,酶解后材料表面被侵蚀,降解速率与失重率结果一致。结论 P(3HB-co-4HB)分子中4HB单体的引入显著影响了材料的机械性能,随着4HB含量的增加,材料的失重率越来越大,热稳定性呈现先上升后下降的趋势,材料表面粗糙度逐渐降低,由于酶解过程属于从表面侵蚀开始,因此酶解过程中样品的结晶度变化不大。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...