Crystal growth and thermal neutron scintillation response of Ce doped KLiYF5

K⁶Li(Y_1−xCe_x)F₅ (x = 0.003, 0.02) single crystals were grown from the melt using the precise atmosphere control type Micro-Pulling-Down (μ-PD) method to examine their potential as a new thermal neutron scintillators. The grown crystals were single-phase materials as confirmed by XRD. The crystals demonstrated 40-60% transmittance above 320 nm and Ce³⁺ 5d-4f luminescence observed around 340 nm when exited by α-ray. The radio luminescence measurements under thermal neutron excitation (²⁵²Cf) demonstrated the light yield of 890 (Ph/neutron) and the decay time excited by α-ray exhibited 20 and 259 ns.     

Bright upconversion emission of Nd in LiLa1−xNdxP4O12 nanocrystalline powders

Upconversion emission of Nd³⁺ doped LiLa_1−xNd_xP₄O₁₂ nanocrystals powders upon irradiation with 808 nm laser diode has been investigated. This emission of bright orange color was dependent on concentration and excitation incident light intensity. It was found that this emission was threshold phenomenon characterized by long build-up times which were dependent on energy of upconversion emission, concentration of active ions, size of nanocrystalline grains and power of incident light. The mechanism of observed upconversion was discussed in terms of thermally stimulated avalanche process. The emission intensity bistability of upconversion emission was demonstrated.     

Monophase domain, fibers single crystals grown by the micro-pulling down technique and optical characterisation of LiGd1−xYbx(WO4)2

We have determined the single phase domain of LiGd_1−xYb_x(WO₄)₂. The lattices parameters decrease as a function of Yb³⁺ substitution in Gd³⁺ sites. Transparent LiGd_1−xYb_x(WO₄)₂ fibers single crystals were successfully grown by the micro-pulling down technique (μ-PD). The Yb³⁺-doped LiGd(WO₄)₂ fibers single crystals have been pulled under stationary stable growth conditions corresponding to flat crystallization interface with meniscus length equal to 120 μm. The fibers diameters varied from 0.5 to 1 mm depending on the capillary die diameter, pulling rate and the molten zone temperature. Fibers single crystals free of defects are observed for Ytterbium concentration in the melt up to 5 at%. Above this limit, inclusions and cracks appear and the optical quality of the fibers were deteriorated. The emission spectra of Yb³⁺-doped LiGd(WO₄)₂ were investigated.     

Synthesis and luminescent properties of novel Ba2−xEuxZr2−yHfySi3O12 phosphor

A series of Eu²⁺ activated luminescent materials according to the composition of Ba_2−xEu_xZr_2−yHf_ySi₃O₁₂ were synthesized using a high temperature solid-state reaction method starting from metal oxides and carbonates. Single phase powders were obtained using two annealing steps and boric acid as a flux. Firstly, starting materials were sintered at 1450 °C for 5 h under CO atmosphere and subsequently annealed at 1200 °C for 5 h under N₂/H₂ (95%/5%) gas flow. All samples were characterized by powder X-ray diffraction (XRD) analysis, thermal quenching (TQ), fluorescence lifetime measurements and photoluminescence (PL) techniques. Moreover, emission colour points, luminous efficacies and quantum efficiencies (QE) were calculated and discussed as a function of Eu²⁺ concentration and Zr/Hf ratio of the host lattice.     

Synthesis and luminescence properties of color-tunable Ba1−ySryLa4−xTbx(WO4)7 (x = 0.02-1.2, y = 0-0.4) phosphors

Ba_1−ySr_yLa_4−xTb_x(WO₄)₇ (x = 0.02-1.2, y = 0-0.4) phosphors were prepared via a solid-state reaction and their photoluminescence properties were investigated. An analysis of the decay behavior indicates that the energy migration between Tb³⁺ ions is conspicuous in the ⁵D₃ → ⁷F₄ transition due to the cross-relaxation in BaLa₄(WO₄)₇. A partial substitution of Ba²⁺ by Sr²⁺ can not only enhance the emission intensity but also increase the solid solubility of Tb³⁺ in Ba_1−ySr_yLa_4−xTb_x(WO₄)₇. The emission intensity of the ⁵D₄ → ⁷F_J (J = 4, 5, 6) transitions can be enhanced by increasing Sr²⁺ and Tb³⁺ concentrations, with the optimal conditions being x = 1.2, y = 0.4 (Ba_0.6Sr_0.4La_2.8Tb_1.2(WO₄)₇). Under near-UV excitation at 379 nm, the CIE color coordinates of Ba_1−ySr_yLa_4−xTb_x(WO₄)₇ vary from blue (0.212, 0.181) at x = 0.04, y = 0, to green (0.245, 0.607) at x = 1.2, y = 0.4.     

Luminescence characteristics of Ce-doped Lu1−xScxBO3 solid solution single crystals grown by Czochralski method

Solid solution crystals of Lu_1−xSc_xBO₃:Ce³⁺ (x = 0.2, 0.3, 0.5, 0.7) were grown by Czochralski method. These crystals have high optical transmittance within wavelength concerned, except for an absorption shoulder in Lu_0.8Sc_0.2BO₃:1at%Ce³⁺ crystal from 360 to 530 nm. With the increase of Sc/Lu ratio, the excitation and emission spectra have redshift due to change of Ce³⁺ crystalline environment and the lifetime gradually increases due to the increase of emission wavelength. Efficient energy transfer from the self-trapped excitons to Ce³⁺ ions was observed. Lu_0.8Sc_0.2BO₃:1at%Ce³⁺ crystal, due to high density, short decay time, high scintillation efficiency and non-hygroscopic property, could be a promising scintillator.     

Crystallization and microstructure of glasses in the system Na2O/MnO/SiO2/Fe2O3

Glasses with the compositions (100 − x)(0.16Na₂O/0.10MnO/0.74SiO₂)/xFe₂O₃, (x = 5-30) and 16Na₂O/10MnO/(74 − y)SiO₂/yFe₂O₃ (y = 5-30) were studied using X-ray diffraction and scanning electron microscopy. The effect of the chemical composition and the thermal history on the phase formation and the resulting microstructure was investigated. During cooling, the precipitation of ferrimagnetic solid solutions Fe₃O₄/Mn₃O₄ was observed. These crystals show dendritic or platelet shape, whereby the platelets are ferromagnetic and the dendrites - mainly paramagnetic. The tendency towards crystallization can be suppressed by increasing the Na₂O-concentration. In contrast to glasses without manganese oxide, the precipitation of hematite is not observed. Therefore, the addition of reducing agents is not required, in order to crystallize large volume concentrations of the ferrimagnetic phase.     

Preparation of PrxZn1 − xO nanopowder with UV-visible light response

We prepared Pr_xZn_1 − xO nanopowder using a combustion method. The sample was characterized by XRD, TEM, XPS, UV-visible and PL spectroscopy. The prepared Pr_xZn_1 − xO nanopowder had a good photon absorption performance in the range of 200-800 nm wavelength. Moreover, the 4f² electronic configuration of trivalent Pr³⁺ ions was revealed from the diffuse reflectance spectra. The single crystalline particle size was about 20-70 nm based on the TEM observation. A quantum size effect of the Pr_xZn_1 − xO nanopowder was also noted.     

Synthesis of (1 − x)Ca2/5Sm2/5TiO3-xLi1/2Nd1/2TiO3 ceramic powder via ethylenediaminetetraacetic acid precursor

(1 − x)Ca_2/5Sm_2/5TiO₃-xLi_1/2Nd_1/2TiO₃ (CSLNT) ceramic powder was prepared by a liquid mixing method using ethylenediaminetetraacetic acid (EDTA) as the chelating agent. TG, DTA, XRD and TEM characterized the precursors and derived oxide powders. When x = 0.3, perovskite CSLNT was synthesized at 1000 °C for 3 h in air. The CSLNT (x = 0.3) ceramics sintered at 1200 °C for 3 h show excellent microwave dielectric properties of ?_r = 99, Q_f = 6200 GHz and τ_f = 9 × 10⁻⁶ °C⁻¹.     

Passive Q-switching performance of intracavity frequency-doubled red laser with mixed Nd:GdxY1−xVO4 crystals

Passive Q-switching laser operation of Nd:Gd_xY_1−xVO₄ mixed crystals at 671 nm has been compared in the same V-shape folded cavity. Based on our comparative analysis, the best laser characteristics - the highest pulse energy and peak power and the shortest pulse width - were demonstrated by Nd:Gd_0.63Y_0.37VO₄ crystal. At the same time, this crystal possesses the lowest thermal conductivity in comparison with the other Nd:Gd_xY_1−xVO₄ crystals, which could result in decreasing the average laser output power. To verify this assumption we also measured the focal lengths of thermal lens induced in the crystals during the laser operation.     

Novel Dy-doped Ca2Gd8(SiO4)6O2 white light phosphors for Hg-free lamps application

The luminescent properties of Ca₂Gd_8(1−x)(SiO₄)₆O₂:xDy³⁺ (1% ≤ x ≤ 5%) powder crystals with oxyapatite structure were investigated under vacuum ultraviolet excitation. In the excitation spectrum, the peaks at 166 nm and 191 nm of the vacuum ultraviolet region can be assigned to the O²⁻ → Gd³⁺, and O²⁻ → Dy³⁺ charge transfer band respectively, which is consistent with the theoretical calculated value using Jφrgensen's empirical formula. While the peaks at 183 nm and 289 nm are attributed to the f-d spin-allowed transitions and the f-d spin-forbidden transitions of Dy³⁺ in the host lattice with Dorenbos's expression. According to the emission spectra, all the samples exhibited excellent white emission under 172 nm excitation and the best calculated chromaticity coordinate was 0.335, 0.338, which indicates that the Ca₂Gd₈(SiO₄)₆O₂:Dy³⁺ phosphor could be considered as a potential candidate for Hg-free lamps application.     

Synthesis and characterization of Ni1−xZnxFe2O4 spinel ferrites from tailored layered double hydroxide precursors

In this paper, a series of pure Ni_1 − xZn_xFe₂O₄ (0 ≤ x ≤ 1) spinel ferrites have been synthesized successfully using a novel route through calcination of tailored hydrotalcite-like layered double hydroxide molecular precursors of the type [(Ni + Zn)_{1 − x − y}Fe_y²⁺Fe_x³⁺(OH)₂]^x+(SO₄²⁻)_x/2·mH₂O at 900 °C for 2 h, in which the molar ratio of (Ni²⁺ + Zn²⁺)/(Fe²⁺ + Fe³⁺) was adjusted to the same value as that in single spinel ferrite itself. The physico-chemical characteristics of the LDHs and their resulting calcined products were investigated by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and Mössbauer spectroscopy. The results indicate that calcination of the as-synthesized LDH precursor affords a pure single Ni_1 − xZn_xFe₂O₄ (0 ≤ x ≤ 1) spinel ferrite phase. Moreover, formation of pure ferrites starting from LDHs precursors requires a much lower temperature and shorter time, leading to a lower chance of side-reactions occurring, because all metal cations on the brucite-like layers of LDHs can be uniformly distributed at an atomic level.     

Morphotropic phase boundary in high temperature ferroelectric xBi(Zn1/2Ti1/2)O3 − yPbZrO3 − zPbTiO3 perovskite ternary solid solution

A bismuth and lead oxide based perovskite ternary solid solution xBi(Zn_1/2Ti_1/2)O₃ − yPbZrO₃ − zPbTiO₃ (xBZT − yPZ − zPT) was investigated as an attempt to develop a high T_C ferroelectric material for piezoelectric sensor and actuator applications. A morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases was determined through an XRD study on a pseudobinary line 0.1BZT − 0.9[xPT − (1 − x)PZ] for composition 0.1Bi(Zn_1/2Ti_1/2)O₃ − 0.5PbZrO₃ − 0.4PbTiO₃. Enhanced piezoelectric and ferroelectric activities were observed for MPB composition with dielectric constant ε_r′ ~ 23,000 at Curie temperature (T_C) ≈ 320 °C, remanent polarization (P_r) = 35 μC/cm², piezoelectric coefficient (d₃₃) = 300 pC/N, unipolar strain = 0.15%, and electromechanical coupling coefficient (k_P) = 0.45.     

One-step synthesis and double emission (Ca1 + x − yEuy)Ga2S4 + x phosphor for white LEDs

(Ca_{1 + x − y}Eu_y)Ga₂S_4 + x phosphors have been synthesized one step by solid state reaction. The photoluminescence excitation and emission spectra of phosphors have been studied; the influence of host composition and Eu²⁺ concentration on emission spectra has also been investigated. The emission spectrum consists of yellow emission at 550 nm and red emission at 650 nm. It also indicates that the excitation spectrum is a broadband and can be well matched with the emission of GaN chip. Combined these phosphors with 460 nm-emitting GaN chips, White LEDs have been fabricated. Their electroluminescence spectra have been measured under 20 mA forward-bias current. Their CIE chromaticity coordinates and color temperature indicate that (Ca_{1 + x − y}Eu_y)Ga₂S_4 + x phosphors are promising phosphors for GaN-based white LEDs.     

Leakage current characteristics of Bi3.15Nd0.85Ti3 − xZrxO12 thin films

Thin films of Bi_3.15Nd_0.85Ti₃O₁₂ (BNT) and Bi_3.15Nd_0.85Ti_3 − xZr_xO₁₂ (BNTZ_x, x = 0.1 and 0.2) were fabricated on Pt/TiO₂/SiO₂/Si(100) substrates by a chemical solution deposition (CSD) technique at 700 °C. Structures, surface morphologies, leakage current characteristics and Curie temperature of the films were studied as a function of Zr ion content by X-ray diffraction, atomic force microscopy, ferroelectric test system and thermal analysis, respectively. Experimental results indicate that Zr ion substitution in the BNT film markedly decreases the leakage current of the film, while almost not changing the Curie temperature of the film, which is at about 420-460 °C. The decrease of the leakage current in BNTZ_x films is that the conduction by the electron hopping between Ti⁴⁺ and Ti³⁺ ions is depressed because Zr⁴⁺ ions can block the path between two adjacent Ti ions and enlarge hopping distance.     

Novel transparent conducting oxide: Anatase Ti1−xNbxO2

Single-crystalline Ti_1−xNb_xO₂ (x = 0.2) films of 40 nm thickness were deposited on SrTiO₃ (100) substrates by the pulsed laser deposition (PLD) technique. X-ray diffraction measurement confirmed epitaxial growth of anatase (001) film. The resistivity of Ti_1−xNb_xO₂ films with x ≥ 0.03 is 2-3 × 10^− 4 Ω cm at room temperature. The carrier density of Ti_1−xNb_xO₂, which is almost proportional to the Nb concentration, can be controlled in a range of 1 × 10¹⁹ to 2 × 10²¹ cm^− 3. Optical measurements revealed that internal transmittance in the visible and near-infrared region for films with x = 0.03 was more than 97%. These results demonstrate that the presently developed anatase Ti_1−xNb_xO₂ is one of the promising candidates for the practical TCOs.     

Materials with layered structures XIII: electrical and optical properties of layered chalcogenides in the system CoIn2S4-CoIn2Se4

The system CoIn₂S_4xSe_4(1−x) has been investigated by X-ray powder methods on samples quenched at 700 °C. The spinel type phase has a phase width of 1≥x>0.9. A new layered compound is formed for 0.9>x>0.45 which crystallizes with the α-FeGa₂S₄-type with a=392.6 pm and c=1270.3 pm (x=0.5) for the hexagonal cell. Platelike crystals of the layered phase are obtained by transport reactions with iodine in a temperature gradient 750→700 °C. The band gaps of these crystals measured by optical absorption vary from 1.2 to 1.4 eV. The electrical conductivities of the crystals are found in the order of 10⁻⁵ Ω⁻¹ cm⁻¹.