共查询到20条相似文献,搜索用时 93 毫秒
1.
针对SWRH82B盘条在拉拔过程中出现的拉拔断裂,通过断口形貌分析、成分分析和金相组织分析等方法对SWRH82B盘条笔尖状断口的形成原因进行分析。结果表明,由于该盘条心部存在碳偏析,形成网状碳化物等硬脆相,在拉拔过程中硬脆相易与基体形成微裂纹,随着加工的深入,萌生裂纹扩展并最终断裂。 相似文献
2.
3.
某单位从国外进口了一批控轧SWRH82B盘条料,用于直接拉拔成钢丝再合绞成低松弛预应力钢绞线。其中Φ12.7 mm盘条拉成的钢丝,在作拉力试验时出现较多的尖锥形脆断现象,且有些钢丝在绞线过程中断丝。本试验对其进行原因分析。 相似文献
4.
对SWRH82B盘条的断口样品进行了宏观断口和微观组织分析结果表明,断口样品可以分为三类:第一类为盘条断口,第二类为斜劈状钢丝断口,第三类为笔尖状钢丝断口其中,造成第一、二类断口的直接原因是盘条表面擦伤,第三类断口出现的主要原因是盘条心部存在较严重的网状渗碳体 相似文献
5.
6.
通过对高碳钢绞线SWRH82B拉丝材笔尖断裂的分析,得出笔尖状断口的中心网状碳化物级别≥4,存在较严重的碳偏析,组织转变上的差异导致拉拔变形不均匀产生断裂缺陷。通过对180 mm×180 mm断面高碳钢SWRH82B方坯中心碳偏析产生机理的研究,将钢水过热度从15~40℃调整为20~30℃、拉速由1.5 m/min降至1.4 m/min、末端电磁搅拌由电流350A增加至400A,钢坯的碳偏析指数由1.18降至1.06,明显降低了SWRH82B钢的拉丝材笔尖状断口发生率。 相似文献
7.
8.
9.
10.
文章采用金相组织检验以及电镜扫描等方法,对拉拔、绞线过程中产生断裂的SWRH82B盘条进行检验,得出引起断裂的原因主要是心部马氏体和夹杂物的存在。另外,生产加工工艺的不合理也是盘条质量较差的一个重要原因。通过改善生产加工工艺,盘条质量明显改善,拉拔断丝现象减少。 相似文献
11.
13.
15.
20.
《天津冶金》2009,(4):81-84
Cause Analysis and Preventive Measures for Inclusion Formation in Aluminized Steel
Wang Baoming, Wang Wenhui, Hu Guangwen, Deng Zhiyong
Abstract: Through tracking and analysis on the source of inclusion in aluminum steel, it is determined that A1203 is the source of inclusion, which congregates in the mould and is carfled into the billet. Processes of LF wire feeding and calcium treatment are optimized and relevant measures are taken to settle the existing problems. The billet quality is improved and inclusion kept within the standard. 相似文献
Wang Baoming, Wang Wenhui, Hu Guangwen, Deng Zhiyong
Abstract: Through tracking and analysis on the source of inclusion in aluminum steel, it is determined that A1203 is the source of inclusion, which congregates in the mould and is carfled into the billet. Processes of LF wire feeding and calcium treatment are optimized and relevant measures are taken to settle the existing problems. The billet quality is improved and inclusion kept within the standard. 相似文献