Electromigration in Cu-Cored Sn-3.5Ag-0.7Cu Solder Interconnects Under Current Stressing

The effect of electromigration in Cu-cored Sn-3.5Ag-0.7Cu solder interconnects under current stressing was investigated. After current stressing at a density of 2 × 10⁴ A/cm², some Cu₆Sn₅ intermetallic compounds accumulated abnormally on the surface of the solder interconnect. The abnormal accumulation phenomenon was explained by the mechanism that thermomigration dominated the migration process. Furthermore, some Cu₆Sn₅ extrusions appeared on the cathode-side surface of the solder interconnect due to the compressive stresses induced by electromigration and thermomigration.     

Effects of Surface Finishes and Current Stressing on Interfacial Reaction Characteristics of Sn-3.0Ag-0.5Cu Solder Bumps

The effects of surface finishes on the in situ interfacial reaction characteristics of ball grid array (BGA) Sn-3.0Ag-0.5Cu lead-free solder bumps were investigated under annealing and electromigration (EM) test conditions of 130°C to 175°C with 5.0 × 10³ A/cm². During reflow and annealing, (Cu,Ni)₆Sn₅ intermetallic compound (IMC) formed at the interface of electroless nickel immersion gold (ENIG) finish. In the case of both immersion Sn and organic solderability preservative (OSP) finishes, Cu₆Sn₅ and Cu₃Sn IMCs formed. Overall, the IMC growth velocity of ENIG was much lower than that of the other finishes. The activation energies of total IMCs were found to be 0.52 eV for ENIG, 0.78 eV for immersion Sn, and 0.72 eV for OSP. The ENIG finish appeared to present an effective diffusion barrier between the Cu substrate and the solder, which leads to better EM reliability in comparison with Cu-based pad systems. The failure mechanisms were explored in detail via in situ EM tests.     

Low-Cycle Fatigue Behavior of 95.8Sn-3.5Ag-0.7Cu Solder Joints

Low-cycle fatigue (LCF) behavior of 95.8Sn-3.5Ag-0.7Cu solder joints was investigated over a range of test temperatures (25°C, 75°C, and 125°C), frequencies (0.001 Hz, 0.01 Hz, and 0.1 Hz), and strain ranges (0.78%, 1.6%, and 3.1%). Effects of temperature and frequency on the LCF life were studied. Results show that the LCF lifetime decreases with an increase in test temperature or a decrease of test frequency, which is attributed to the longer exposure time to creep and the stress relaxation mechanism during fatigue testing. A modified Coffin–Manson model considering effects of temperature and frequency on the LCF life is proposed. The fatigue exponent and ductility coefficient were found to be influenced by both the temperature and frequency. By fitting the experimental data, the mathematical relations between the fatigue exponent and temperature, and ductility coefficient and temperature, were analyzed. Scanning electron microscopy (SEM) of the cross-sections and fracture surfaces of failed specimens at different temperature and frequency was applied to verify the failure mechanisms.     

Influence of Lanthanum Additions on the Microstructure and Microhardness of Sn-3.5Ag Solder

This study evaluates the effects of different amounts of lanthanum (La) additions on the microstructure and microhardness of Sn-3.5Ag solders. Sn-3.5Ag-xLa ternary solders were prepared by adding 0 wt.% to 1.0 wt.% La to Sn-3.5Ag alloy. Copper substrates were then dipped in the molten solders and these samples aged at 150°C for up to 625 h. The microstructure and microhardness of the as-solidified solder and the aged solder/copper samples were investigated. The Sn-3.5Ag-xLa solders comprised β-Sn, Ag₃Sn, and LaSn₃ phases, and their microstructure was refined by La additions. As-cast, the addition of La increased the microhardness of the Sn-Ag solder due to the refining effect of Ag₃Sn particles and increased formation of LaSn₃ compounds. As the aging time was increased, the microhardness of the solders decreased and the Ag₃Sn compounds coarsened. However, the coarsening of Ag₃Sn compounds was retarded by La, and the size and amount of LaSn₃ compounds did not change perceptibly with aging time. Therefore, La additions can improve the microhardness and thermal resistance of solder joints.     

Intermetallic Compound Growth and Reliability of Cu Pillar Bumps Under Current Stressing

Fine-pitch Cu pillar bumps have been adopted for flip-chip bonding technology. Intermetallic compound (IMC) growth in Cu pillar bumps was investigated as a function of annealing or current stressing by in situ observation. The effect of IMC growth on the mechanical reliability of the Cu pillar bumps was also investigated. It is noteworthy that Sn exhaustion was observed after 240 h of annealing when current stressing was not applied, and IMC growth rates were changed remarkably. As the applied current densities increased, the time required for complete Sn consumption became shorter. In addition, Kirkendall voids, which would be detrimental to the mechanical reliability of Cu pillar bumps, were observed in both Cu₃Sn/Cu pillars and Cu₃Sn/Cu under-bump metallization interfaces. Die shear force was measured for Cu pillar samples prepared with various annealing times, and degradation of mechanical strength was observed.     

Additive Effect of Kirkendall Void Formation in Sn-3.5Ag Solder Joints on Common Substrates

The Sn-3.5Ag and Sn-3.5Ag-0.2Co-0.1Ni lead-free solders were investigated on common electronics substrates, namely, organic solderability preservative (OSP) and electroless Ni/immersion Au (ENIG) surface finishes. The formation of Kirkendall voids at the interfacial region during isothermal solid aging was explored. For the Sn-3.5Ag-0.2Co-0.1Ni/OSP solder joint, the Kirkendall voids were present after isothermal solid-state aging at higher temperature (e.g., 150°C); however, the size of voids did not change remarkably with prolonged aging time due to the depressed Cu₃Sn layer growth. For ENIG surface finishes, the 0.2Co-0.1Ni additions seemed to enhance the longitudinal groove-shaped voids at the Ni₃P layer; however, void formation at the solder/Ni₃Sn₄ interface was effectively reduced. This might be attributed to the reduced Sn activity in the solder matrix and the suppressed Ni-P-Sn layer formation.     

Joule Heating Enhanced Phase Coarsening in Sn37Pb and Sn3.5Ag0.5Cu Solder Joints during Current Stressing

This paper investigated the effect of Joule heating on the phase coarsening in Sn37Pb and Sn3.5Ag0.5Cu ball grid array (BGA) solder joints stressed at −5°C and 125°C with a 6.0 × 10² A/cm² electric current. The phase growth under current stressing was also compared with those under aging at 125°C. It was found that the current stressing produced a substantial Joule heating in the solder joints and conductive traces. Hence, the solder joints underwent a considerable temperature rise by 30–35°C when stressed at −5°C and 125°C in this study. Coarsening of Pb-rich and Ag-rich phases was confirmed to be accelerated by the current stressing as a result of enhanced diffusion at elevated temperature and atomic stimulation due to numerous collisions between electrons and atoms. Different controlling kinetics were suggested for the cases stressed or aged at different temperatures.     

Intermetallics Evolution in Sn-3.5Ag Based Lead-Free Solder Matrix on an OSP Cu Finish

The 0.2Co + 0.1Ni dual additives were used to dope a Sn-3.5Ag solder matrix to modify the alloy microstructure and the solder joint on an organic solderability preservative (OSP) Cu pad. The refined microstructure of the Sn-3.5Ag-0.2Co-0.1Ni solder alloy or the reduced β-Sn size was attributed to the depressed undercooling achieved by the Co-Ni addition. After soldering on the OSP Cu pad, a large Ag₃Sn plate was formed at the Sn-3.5Ag/OSP solder joint, whereas it was absent at the Sn-3.5Ag-0.2Co-0.1Ni/OSP solder joints. With isothermal aging at 150°C, large Ag₃Sn plates formed at the Sn-3.5Ag/OSP solder joint were still observed. A coarsened and dispersed Ag₃Sn phase was found in the solder joints with Co-Ni additions as well. Compared to Cu₆Sn₅, the (Co,Ni)Sn₂ intermetallic compound showed much lower microhardness values. However, (Co,Ni)Sn₂ hardness was comparable to that of the Ag₃Sn phase. Pull strength testing of Sn-3.5Ag-0.2Co-0.1Ni/OSP revealed slightly lower values than for Sn-3.5Ag/OSP during aging. Such results are thought be due to the phase transformation of (Co,Ni)Sn₂ to (Cu,Co,Ni)₆Sn₅.     

Characterization of Interfacial Reaction Layers Formed Between Sn-3.5Ag Solder and Electroless Ni-Immersion Au-Plated Cu Substrates

The interfacial reaction between a eutectic Sn-3.5wt.%Ag solder and an electroless nickel–immersion gold-plated Cu substrate during reflow was examined by transmission electron microscopy (TEM). During the initial reflowing, the amorphous, electroless Ni (P)-plated layer crystallized into two P-rich Ni layers: a Ni₁₂P₅ + Ni₃P mixed upper layer and a Ni₃P lower layer. No ternary Ni-Sn-P layer was observed in the initial stage. After subsequent reflow for 60 s, a ternary Ni₂SnP layer (containing a small amount of the Ni₃P phase) was formed between the Ni₃Sn₄ and P-rich Ni layers (Ni₃P + Ni₁₂P₅ + Ni).     

Effect of Interfacial Reaction on the Tensile Strength of Sn-3.5Ag/Ni-P and Sn-37Pb/Ni-P Solder Joints

This work investigates the effect of interfacial reaction on the mechanical strength of two types of solder joints, Sn-3.5Ag/Ni-P and Sn-37Pb/Ni-P. The tensile strength and fracture behavior of the joints under different thermal aging conditions have been studied. It is observed that the tensile strength decreases with increasing aging temperature and duration. Associated with the tensile strength decrease is the transition of failure modes from within the bulk solder in the as-soldered condition toward failures at the interface between the solder and the intermetallic compounds (IMCs). For the same aging treatment, the strength of the Sn-3.5Ag/Ni-P joint degrades faster than that of Sn-37Pb/Ni-P. The difference between the two types of joints can be explained by the difference in their interfacial reaction and growth kinetics. An empirical relation is established between the solder joint strength and the Ni₃Sn₄ intermetallic compound thickness.     

Corrosion Behavior of Pb-Free Sn-1Ag-0.5Cu-XNi Solder Alloys in 3.5% NaCl Solution

Potentiodynamic polarization techniques were employed in the present study to investigate the corrosion behavior of Pb-free Sn-1Ag-0.5Cu-XNi solder alloys in 3.5% NaCl solution. Polarization studies indicated that an increase in Ni content from 0.05 wt.% to 1 wt.% in the solder alloy shifted the corrosion potential (E _corr) towards more negative values and increased the linear polarization resistance. Increased addition of Ni to 1 wt.% resulted in significant increase in the concentration of both Sn and Ni oxides on the outer surface. Secondary-ion mass spectrometry and Auger depth profile analysis revealed that oxides of tin contributed primarily towards the formation of the passive film on the surface of the solder alloys containing 0.05 wt.% and 1 wt.% Ni. Scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) established the formation of a Sn whisker near the passive region of the solder alloy obtained from the polarization curves. The formation of Sn whiskers was due to the buildup of compressive stress generated by the increase in the volume of the oxides of Sn and Ni formed on the outer surface. The presence of Cl^? was responsible for the breakdown of the passive film, and significant pitting corrosion in the form of distinct pits was noticed in Sn-1Ag-0.5Cu-0.5Ni solder alloy after the polarization experiment.     

Effects of Co Addition on Bulk Properties of Sn-3.5Ag Solder and Interfacial Reactions with Ni-P UBM

The effects of Co addition on the undercooling, microstructure, and microhardness of Sn-3.5Ag solder (all in wt.% unless specified otherwise) and interfacial reactions with Ni-P under bump metallurgy (UBM) are investigated when the Co content varies from 0.01 wt.% to 0.7 wt.%. When more than 0.02 wt.% Co was added to Sn-3.5Ag solder, the undercooling of the Sn-3.5Ag solder was significantly reduced and the microstructures coarsened with the increased eutectic region. In addition, the hardness value increased as the Co content in Sn-3.5Ag increased. In the interfacial reactions with Ni-P UBM, a spalling phenomenon of intermetallic compounds (IMCs) during reflow was prevented in the Sn-3.5Ag-xCo (x ≥ 0.02 wt.%). However, when more than 0.05 wt.% Co was added to Sn-3.5Ag, the IMC morphology changed from a bulky shape to a plate-like shape. The bulky IMCs were Ni₃Sn₄ and the plate-like IMCs were Sn-Ni-Co ternary compounds. The main issues discussed include the relations between the morphological changes and the IMC phases, the effects of Co addition on the prevention of IMC spalling, and the optimum level of Co addition.     

Effect of Electromigration on the Mechanical Performance of Sn-3.5Ag Solder Joints with Ni and Ni-P Metallizations

The effect of moderate electric current density (1 × 10³ to 3 × 10³ A/cm²) on the mechanical properties of Ni-P/Sn-3.5Ag/Ni-P and Ni/Sn-3.5Ag/Ni solder joints was investigated using a microtensile test. Thermal aging was carried out at 160°C for 100 h while the current was passed. The interfacial microstructure and intermetallic compound (IMC) growth were analyzed. It was found that, at these levels of current density, there were no observable voids or hillocks. Samples aged at 160°C without current stressing failed mostly inside the bulk solder with significant prior plastic deformation. The passage of current was found to cause brittle failure of the solder joints and this tendency for brittle failure increased with increasing current density. Fractographic analysis showed that, in most of the electrically stressed samples, fracture occurred at the interface region between the solder and the joining metals. The critical current density that caused brittle fracture was about 2 × 10³ A/cm². Once brittle fracture occurred, the tensile toughness, defined as the energy per unit fractured area, was usually lower than ~5 kJ/m², compared with the case of ductile fracture where this value was typically greater than ~9 kJ/m². When comparing the two types of joint, the brittle failure was found to be more severe with the Ni than with the Ni-P joint. This work also found that the passage of electric current affects the IMC growth rate more significantly in the Ni than in the Ni-P joint. In the case of the Ni joint, the Ni₃Sn₄ IMC at the anode side was appreciably thicker than that formed at the cathode side. However, in the case of electroless Ni-P metallization, this difference was much smaller.     

Effects of Forming Processes on the Microstructure and Solderability of Sn-3.5Ag Eutectic Solder Ribbons as well as the Mechanical Properties of Solder Joints

Two kinds of Sn-3.5Ag eutectic solder ribbons of 0.13 mm thickness were prepared by a casting–rolling process and a rapid solidification process. The microstructure, phase constitution, melting characteristics, wetting behavior and soldering strength were compared using optical microscopy, scanning electron microscopy, x-ray diffraction, energy dispersive spectroscopy, differential scanning calorimetry and a MTS ceramic testing system. The results show that the microstructure of rapidly solidified solder is finer and more uniform, and the eutectic structure has a higher solid solubility and more homogeneous distribution of Ag in a Sn matrix. The solidus and liquidus temperature decreased, resulting in a 3.3% reduction of pasty range. In addition, the wettability and shear strength of the solder joints increased by 13.2% and 7.9%, respectively.     

A Study on the Physical Properties and Interfacial Reactions with Cu Substrate of Rapidly Solidified Sn-3.5Ag Lead-Free Solder

A rapidly solidified Sn-3.5Ag eutectic alloy produced by the melt-spinning technique was used as a sample in this research to investigate the microstructure, thermal properties, solder wettability, and inhibitory effect of Ag₃Sn on Cu₆Sn₅ intermetallic compound (IMC). In addition, an as-cast Sn-3.5Ag solder was prepared as a reference. Rapidly solidified and as-cast Sn-3.5Ag alloys of the same size were soldered at 250°C for 1 s to observe their instant melting characteristics and for 3 s with different cooling methods to study the inhibitory effect of Ag₃Sn on Cu₆Sn₅ IMC. Experimental techniques such as scanning electron microscopy, differential scanning calorimetry, and energy-dispersive spectrometry were used to observe and analyze the results of the study. It was found that rapidly solidified Sn-3.5Ag solder has more uniform microstructure, better wettability, and higher melting rate as compared with the as-cast material; Ag₃Sn nanoparticles that formed in the rapidly solidified Sn-3.5Ag solder inhibited the growth of Cu₆Sn₅ IMC during aging significantly much strongly than in the as-cast material because their number in the rapidly solidified Sn-3.5Ag solder was greater than in the as-cast material with the same soldering process before aging. Among the various alternative lead-free solders, this study focused on comparison between rapidly solidified and as-cast solder alloys, with the former being observed to have better properties.     

An X-ray Radiography Study of the Effect of Thermal Cycling on Damage Evolution in Large-Area Sn-3.5Ag Solder Joints

There is a need for next-generation, high-performance power electronic packages and systems utilizing wide-band-gap devices to operate at high temperatures in automotive and electricity transmission applications. Sn-3.5Ag solder is a candidate for use in such packages with potential maximum operating temperatures of about 200°C. However, there is a need to understand the thermal cycling reliability of Sn-3.5Ag solders subject to such high-temperature operating conditions. The results of a study on the damage evolution occurring in large-area Sn-3.5Ag solder joints between silicon dies and direct bonded copper substrates with Au/Ni-P metallization subject to thermal cycling between 200°C and 5°C are presented in this paper. Interface structure evolution and damage accumulation were followed using high-resolution X-ray radiography, cross-sectional optical and scanning electron microscopies, and X-ray microanalysis in these joints for up to 3000 thermal cycles. Optical and scanning electron microscopy results showed that the stresses introduced by the thermal cycling result in cracking and delamination at the copper–intermetallic compound interface. X-ray microanalysis showed that stresses due to thermal cycling resulted in physical cracking and breakdown of the Ni-P barrier layer, facilitating Cu-Sn interdiffusion. This interdiffusion resulted in the formation of Cu-Sn intermetallic compounds underneath the Ni-P layer, subsequently leading to delamination between the Ni-rich layer and Cu-Sn intermetallic compounds.     

Electromigration Behavior in Sn-37Pb and Sn-3.0Ag-0.5Cu Flip-Chip Solder Joints under High Current Density

The electromigration of conventional Sn-37Pb and Pb-free Sn-3.0Ag-0.5Cu (in wt.%) solder bumps was investigated with a high current density of 2.5 × 10⁴ A/cm² at 423 K using flip-chip specimens comprised of an upper Si chip and a lower bismaleimide triazine (BT) substrate. Electromigration failure of the Sn-37Pb and Sn-3.0Ag-0.5Cu solder bumps occurred with complete consumption of electroless Ni immersion Au (ENIG) underbump metallization (UBM) and void formation at the cathode side of the solder bump. Finite element analysis and computational simulations indicated high current crowding of electrons in the patterned Cu on the Si chip side, whereas the solder bumps and Cu line of the BT substrate had a relatively low density of flowing electrons. These findings were confirmed by the experimental results. The electromigration reliability of the Sn-3.0Ag-0.5Cu solder joint was superior to that of Sn-37Pb.