Surface grafting of polymers onto ultrafine silica: cationic polymerization initiated by benzylium perchlorate groups introduced onto ultrafine silica surface

Summary The cationic graft polymerization initiated by benzylium perchlorate groups introduced onto ultrafine silica surface was investigated. The introduction of benzylium perchlorate groups onto the surface was achieved by the reaction of silver perchlorate with surface benzyl chloride groups, which were introduced by the treatment of silica with 4-(chloromethyl)phenyltrimethoxysilane. The cationic graft polymerization of styrene and cationic ring-opening polymerization of -caprolactone were found to be initiated by the surface benzylium perchlorate groups and the corresponding polymers were grafted onto the surface. The percentage of grafting onto silica surface decreased with increasing polymerization temperature, because chain transfer reaction of growing polymer cation is accelerated with increasing polymerization temperature.     

Cationic graft polymerization of polymers from carbon fiber initiated by acylium perchlorate groups introduced onto the surface

The cationic graft polymerization of several monomers initiated by acylium perchlorate groups introduced onto the carbon fiber surface was investigated to modify the surface. The introduction of acylium perchlorate groups was successfully achieved by the reaction of silver perchlorate with acyl chloride groups, which were introduced by the reaction of surface carboxyl groups with thionyl chloride. It was found that the cationic polymerization of styrene is initiated by acylium perchlorate groups on the carbon fiber. In the polymerization, polystyrene was grafted onto the carbon fiber surface through the propagation of polystyrene from the surface. Ungrafted polymer was also formed by the chain transfer reaction of growing polymer cation to the monomer. The acylium perchlorate groups have the ability to initiate cationic ring-opening polymerization of tetrahydrofuran (THF) and ε-caprolactone (CL), polyTHF and polyCL being grafted onto the carbon fiber surface, respectively. Polyacetals, such as poly(1,3-dioxolane) and polyoxymethylene, were able to graft onto the carbon fiber by cationic ring-opening polymerization of the corresponding monomers.     

Surface grafting of polymer onto carbon thin film

The surface grafting of polymers onto carbon thin film deposited on a glass plate was achieved by two methods: the graft polymerization initiated by initiating groups introduced onto the surface; and the trapping of polymer radicals by surface aromatic rings of the thin film. It was found that the radical and cationic graft polymerization of vinyl monomers are initiated by azo and acylium perchlorate groups introduced onto the surface, respectively, and the corresponding polymers are grafted onto the surface: the surface grafting of polymers were confirmed by the contact angle of the surface with water. In addition, the anionic ring-opening alternating copolymerization of epoxides with cyclic acid anhydrides was found to be initiated by potassium carboxylate groups on the carbon thin film to give the corresponding polyester-grafted carbon thin film. On the other hand, polymer radicals formed by the decomposition of azo polymer, such as poly(polydimethylsiloxane-azobiscyanopentanoate) and poly(polyoxyethylene-azobiscyanopentanoate), were successfully trapped by the surface aromatic rings of carbon thin film and polydimethylsiloxane and polyoxyethylene were grafted onto the surface. © 1995 John Wiley & Sons, Inc.     

Preparation and dispersibility of poly(L‐lactide)‐grafted silica nanoparticle

To improve dispersibility of silica nanoparticle in organic solvents, the grafting of poly(L ‐lactide) (PLLA) onto silica nanoparticle surface by ring‐opening polymerization of L‐lactide (LA) was investigated in the presence of an amidine base catalyst. The ring‐opening polymerization of LA successfully initiated in the presence of silica having amino groups (silica‐NH₂) and an amidine base catalyst to give PLLA‐grafted silica, but not in the presence of untreated silica (silica‐OH). In the absence of the amidine base catalyst no ring‐opening polymerization of LA even in the presence of silica‐NH₂ and no grafting of PLLA onto silica were observed. It became apparent that the amidine base catalyst acts as an effective catalyst for the ring‐opening graft polymerization of LA from the surface of silica‐NH₂. In addition, it was found that the percentage of PLLA grafting onto silica could be controlled according to the reaction conditions. The average particle size of PLLA‐grafted silica was smaller than that of silica‐NH₂. Therefore, it was considered that the aggregation structure of silica nanoparticles was considerably destroyed by grafting of PLLA onto the surface. The PLLA‐grafted silica gave a stable dispersion in polar solvents, which are good solvents for PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of initiating groups introduced onto ultrafine silica on the molecular weight polystyrene grafted onto the surface

Summary The effect of initiating groups introduced onto silica surface on the molecular weight of grafted polystyrene chain was investigated. By the treatment of polystyrene-grafted silica with aqueous solution of alkali, surface grafted polystyrene was isolated from the surface. The molecular weight of polystyrene grafted onto the silica obtained from the radical graft polymerization initiated by peroxyester groups introduced onto the surface was found to be much larger than that from the cationic polymerization initiated by acylium perchlorate groups. The number of grafted polystyrene in the radical polymerization, however, was much less than that in the cationic polymerization. Furthermore, the effect of molecular weight of grafted polystyrene on the dispersibility of silica in tetrahydrofuran was examined.     

黄原胶与丙烯酰胺接枝共聚反应的研究

以过硫酸铵为引发剂,在氮气保护下,研究了黄原胶与丙烯酰胺的接枝共聚反应。考察了单体浓度、引发剂浓度、反应温度和反应时间等因素对接枝率及接枝效率的影响,探讨了过硫酸铵引发黄原胶接枝丙烯酰胺共聚反应的基本规律。采用红外光谱、X射线粉末衍射对接枝共聚物的结构进行研究,用热重分析法表征了产物的热性能,并初步探讨了接枝机理。结果表明,过硫酸铵能有效地引发黄原胶与丙烯酰胺的接枝共聚反应,并且接枝率和接枝效率随单体浓度、引发剂浓度、反应温度的变化出现极大值,随反应时间的延长不断上升,直至基本不变。     

黄原胶与丙烯酸接枝共聚反应的研究

以过硫酸钾为引发剂,在氮气保护下,研究了黄原胶（XG）与丙烯酸（AA）的接枝共聚反应。考察了单体浓度、引发剂浓度、反应温度和反应时间等因素对接枝率及接枝效率的影响,探讨了过硫酸钾引发黄原胶接枝丙烯酸共聚反应的基本规律。采用红外光谱（FT—IR）对接枝共聚物的结构进行研究,并初步探讨了接枝机理。     

A comparative study on effects of two kinds of polymerization methods on grafting of polymer onto silica surface

In this article we present the result of a comparative study of two kinds of polymerization methods—solution polymerization (sol. poly.) and dispersion polymerization (dis. poly.) for grafting polymer onto silica. As a model for the grafting polymerization reaction, styrene was chosen as the monomer and azo diisobutyronitrile (AIBN) as the initiator. The study aims at supplying theoretical reference for better selecting polymerization method to graft polymer on the silica particle surface. First, monolayers of 3‐methacryloylpropyl trimethoxysilane were chemically bonded onto the surfaces of micrometer‐sized silica gel particles, and so double bonds were immobilized onto the silica surface. Second, the copolymerizations between the immobilized double bonds and the monomer styrene were carried out, homopolymerizations of styrene followed, and finally polystyrene was grafted to the silica surfaces. Two kinds of polymerization methods, sol. poly. and dis. poly., were adopted respectively, and the effects of polymerization methods on grafting process were examined mainly. At the same time, the effects of different polymerization conditions on the grafting degree were researched. It was found that in the dis. poly. system the grafting degree is obviously higher than that in the sol. poly. system under the same polymerization conditions, and the grafting degree can go up to 47%, i.e. 47g/100g. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5808–5817, 2006     

Graft polymerization of polyvinylpyrrolidone onto silica

A new technique is reported for the surface grafting of polyvinylpyrrolidone (PVP) to hydroxylated solid surfaces. Free radical graft polymerization of vinylpyrrolidone onto vinylsilane–modified impermeable silica particles was carried out in an aqueous slurry reactor. The graft yield and the monomer conversion were determined by thermogravimetric analysis and UV spectroscopy, respectively. The graft yield was shown to increase by increasing the initial monomer concentration. A comparison of the graft polymerization reaction with the adsorption of polyvinylpyrrolidone onto untreated, vinylsilane-modified, and PVP-grafted silica was performed.     

Surface grafting of polymers onto glass plate: Polymerization of vinyl monomers initiated by initiating groups introduced onto the surface

The surface grafting of polymers onto a glass plate surface was achieved by the polymerization of vinyl monomers initiated by initiating groups introduced onto the surface. Azo groups were introduced onto the glass plate surface by the reaction of 4,4′-azobis(4-cyanopentanoic acid) with isocyanate groups, which were introduced by the treatment with tolylene-2,4-diisocyanate. The radical polymerization of various vinyl monomers was initiated by azo groups introduced onto the glass plate surface and the corresponding polymers were grafted from the surface: The surface grafting of polymers was confirmed by IR spectra, and the contact angle of surface, with water. The contact angle of the glass plate increased by the grafting of hydrophobic polymers, but decreased by the grafting of hydrophilic polymers. The radical postpolymerization was successfully initiated by the pendant peroxycarbonate groups of grafted polymer on the surface to give branched polymer-grafted glass plate. The cationic polymerization of vinyl monomers was also successfully initiated by benzylium perchlorate groups introduced onto the glass plate surface and the corresponding polymers were grafted onto the surface. The contact angle of the glass plate surface obtained from the cationic polymerization of styrene was larger than that obtained from the radical polymerization. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2165–2172, 1997     

Preparation of high PMMA grafted particle SiO2 using surface initiated free radical polymerization

In this work, a convenient surface-initiated free radical graft-polymerization method, by which polymethacrylic acid (PMAA) with a high grafting density was grafted on silica gel particles, was put forward, and it was feasible and effective. The coupling agent γ-aminopropyltrimethoxysilane (AMPS) was first bound onto the surfaces of silica gel particles, obtaining the modified particles AMPS-SiO₂. So a redox initiation system was constituted with the amino groups on the surfaces of AMPS-SiO₂ particles and ammonium persulphate in the solution. A great deal of primary free radicals on the surfaces of AMPS-SiO₂ particles is produced via the redox initiating reaction, so that the surface-initiated free radical graft- polymerization of methacrylic acid (MAA) on the silica gel particles was realized, giving the grafted particles PMAA/SiO₂ with a high grafting degree (about 30 g/100 g) of PMAA. The effects of the main factors on the surface initiated graft polymerization were examined and the corresponding mechanism was investigated in depth. The experimental results show that for this surface-initiated free radical graft-polymerization of MAA, the suitable temperature is 40 °C. If the temperature is over 40 °C, the graft polymerization will be affected negatively, and the grafting degree of PMAA will decline because of the intense heat decomposition of ammonium persulphate. During the graft polymerization, the grafted polymer layer that has formed is a hindrance to the subsequent graft polymerization. The used amount of initiator and the monomer concentration affect the graft polymerization greatly. The appropriate reaction conditions are as follows: reaction time of 10 h, initiator persulphate amount of 1.1% (it implies the mass percent of the monomer), and monomer MAA concentration of about 5% (it drives at the mass percent of the solution).     

Graft polymerization of vinyl acetate onto silica

A method is reported for the surface grafting of polyvinyl acetate (PVAc) onto modified, nonporous silica. The silica surface was modified by silylation with vinyl(triethoxy) silane followed by graft polymerization of vinyl acetate. The graft yield was measured by thermogravimetric analysis and the monomer conversion was monitored by UV spectral analysis. The rate of the graft polymerization and the graft yield were proportional to the initial monomer concentration. Vinyl acetate conversion followed first-order kinetics and displayed a trend of increasing initial rate with increasing monomer concentration.     

Graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto silica surface by Michael addition

The introduction of peroxycarbonate groups onto a silica surface and the graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto a silica surface were investigated. The introduction of peroxycarbonate groups onto a silica surface was achieved by Michael addition of amino groups introduced onto the silica surface to t‐butylperoxy‐2‐methacryloyloxyethylcarbonate (HEPO). The amount of peroxycarbonate groups was determined to be 0.17 mmol/g. The graft polymerization of various vinyl monomers such as styrene (St), N‐vinyl‐2‐pyrrolidinone (NVPD), and 2‐hydroxyethyl methacrylate (HEMA) was initiated by peroxycarbonate groups introduced onto the silica surface to give the corresponding polymer‐grafted silicas. The percentage of poly(St)‐grafting reached about 120% after 5 h. This means that 1.20 g of poly(St) is grafted onto 1.0 g of silica. The surface of poly(St)‐grafted silica shows a hydrophobic nature, but the surfaces of poly(NVPD) and poly(HEMA)‐grafted silica show a hydrophilic nature. Furthermore, the poly(St)‐grafted silica was found to give a stable colloidal dispersion in a good solvent for the grafted polymer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1491–1497, 1999     

Surface grafting of polymers onto ultrafine silica: Cationic polymerization initiated by oxoaminium perchlorate groups introduced onto ultrafine silica surface

Summary The cationic polymerization initiated by oxoaminium perchlorate groups introduced onto ultrafine silica surface was investigated. The oxoaminium perchlorate groups were successfully introduced by treatment of nitroxyl radicals on silica surface with perchloric acid. The introduction of the nitroxyl radicals was achieved by reaction of 4-hydroxy-2,2,6,6-tetramethyl-piperidinyloxy radical with acid anhydride groups on the surface. The cationic polymerization of isobutyl vinyl ether, N-vinylcarbazole, 2,3-dihydrofuran, and -butyrolactone was initiated by oxoaminium perchlorate groups introduced onto the surface and the corresponding polymers were grafted onto the surface through the propagation of grafted polymer chain from the surface oxoaminium perchlorate groups.     

Postgrafting of vinyl polymers onto hyperbranched poly(amidoamine)-grafted nano-sized silica surface

To prepare polymer-grafted nano-sized silica with hydrophilic core and hydrophobic shell and with higher percentage of grafting, the postgraft polymerization of vinyl polymers onto hyperbranched poly(amidoamine)-grafted (PAMAM-grafted) nano-sized silica initiated by the system consisting of Mo(CO)₆ and terminal trichloroacetyl groups of PAMAM-grafted silica was investigated. The introduction of trichloroacetyl groups onto PAMAM-grafted silica surfaces was readily achieved by the reaction of trichloroacetyl isocyanate with terminal amino groups of PAMAM-grafted silica. It was found that the polymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and glycidyl methacrylate (GMA) was successfully initiated by the system consisting of Mo(CO)₆ and terminal trichloroacetyl groups of PAMAM-grafted silica. In the polymerization, the corresponding vinyl polymers were effectively postgrafted onto PAMAM-grafted silica, based on the propagation of polymer from surface radicals formed by the reaction of terminal trichloroacetyl groups with Mo(CO)₆: the percentage of PMMA postgrafting onto PAMAM-grafted silica reached to 400% after 30 min, but the formation of gel was observed after 35 min. The formation of gel tends to decrease by use of hyperbranched PAMAM-grafted silica with higher percentage of grafting. The vinyl polymer-postgrafted nano-sized silica gave a stable colloidal dispersion in various organic solvents.     

A nonionic hydrogel from the telechelics by utilizing living polymerization of 2-oxazolines

N,N′-dimethyl-2,2′-tetramethylene-bis(2-oxazolinium) bis(methyl-p-toluene sulfonate) ( II ), a cationic polymerization initiator, was synthesized by the reaction of methyl p-toluene sulfonate with 2,2′-tetramethylene-bis-2-oxazoline ( I ) and a cationic ring-opening polymerization of 2-methyl-2-oxazoline [MeOZO] in the presence of ( II ) was carried out to produce poly(MeOZO) telechelics with various molecular weights. These telechelics were hydrolyzed with an aqueous solution of sodium carbonate to obtain hydroxy terminated telechelics of poly(MeOZO). A series of nonionic polyurethane hydrogels was prepared by the crosslinking reactions of the poly(MeOZO) glycol with pluriisocyanates in the presence of ferric acetylacetonate and DMF as the catalyst and reaction medium, respectively. The hydrogels showed good swelling degrees for water and hydrophilic solvents such as DMF, and bad swelling degree for a hydrophobic solvent such as toluene.     

Graft polymerization of vinyl acetate onto silica

The free‐radical graft polymerization of vinyl acetate onto nonporous silica particles was studied experimentally. The grafting procedure consisted of surface activation with vinyltrimethoxysilane, followed by free‐radical graft polymerization of vinyl acetate in ethyl acetate with 2,2′‐azobis(2,4‐dimethylpentanenitrile) initiator. Initial monomer concentration was varied from 10 to 40% by volume and the reaction was spanned from 50 to 70°C. The resulting grafted polymer, which was stable over a wide range of pH levels, consisted of polymer chains that are terminally and covalently bonded to the silica substrate. The experimental polymerization rate order, with respect to monomer concentration, ranged from 1.61 to 2.00, consistent with the kinetic order for the high polymerization regime. The corresponding rate order for polymer grafting varied from 1.24 to 1.43. The polymer graft yield increased with both initial monomer concentration and reaction temperature, and the polymer‐grafted surface became more hydrophobic with increasing polymer graft yield. The present study suggests that a denser grafted polymer phase of shorter chains was created upon increasing temperature. On the other hand, both polymer chain length and polymer graft density increased with initial monomer concentration. Atomic force microscopy–determined topology of the polymer‐grafted surface revealed a distribution of surface clusters and surface elevations consistent with the expected broad molecular‐weight distribution for free‐radical polymerization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 300–310, 2003     

Polymerization and graft copolymerization of styrene initiated by ceric ion in acetonitrile/water solution

The polymerization of styrene initiated by a ceric ion/pinacol system and the graft copolymerization of styrene onto microcrystalline cellulose initiated by ceric ion were studied in the mixed solution composed of acetonitrile and water. Although the graft copolymer of polystyrene onto microcrystalline cellulose was not obtained in the acetonitrile solution, addition of water initiated the polymerization, and the grafting ratio was increased with increasing the water added. The rate of polymerization of styrene in the ceric ion/pinacol system increased similarly with increasing the water content in the solution. Acetonitrile is miscible with water, but the solution was separated to two phases by adding styrene into the solution containing above 20% of water; the monomer was dissolved in both acetonitrile and water phases. The polymer was undissolved in this mixed solution. The effects of water on the polymerization in the mixed solvent system are discussed from the standpoint of reaction mechanism.     

Plasma induced graft polymerization of acrylic acid onto polypropylene monofilament

Plasma induced graft polymerization of acrylic acid onto polypropylene (PP) monofilament was carried to introduce carboxyl functionality on its surface. The monofilament was treated with oxygen plasma to create hydroperoxide groups and subsequent graft polymerization was initiated on this exposed monofilament. It was observed that in the absence of an added inhibitor, the grafting did not proceed because of the extensive homopolymerization which left behind hardly any monomer for the grafting reaction. The addition of ferrous sulfate to the grafting medium led to the homopolymer free grafting reaction. The addition of organics, such as methanol, butanone, and acetone led to complete inhibition of the homopolymerization at 60% content. However, the addition of butanone led to much lower degree of grafting than methanol and acetone. The contact angle of the monofilament showed drastic reduction by plasma treatment and by the subsequent grafting of acrylic acid. The grafting in ferrous sulfate medium showed higher contact angles as compared to the grafting in organic medium. The surface morphology was significantly influenced by the nature of the additive in the grafting medium. © 2007 Wiley Periodicals, Inc. JAppl Polym Sci, 2008     

Surface grafting of polymers onto aramid powder: graft polymerization of vinyl monomers initiated by azo groups introduced onto the surface of aramid powder

The radical graft polymerization of vinyl monomers onto the surface of aramid powder, i.e., poly(p-phenylene terephthalamide) powder, initiated by azo groups introduced onto the surface was investigated. The introduction of azo groups onto the aramid surface was achieved by the reaction of surface acyl chloride groups, which were introduced by the treatment of aramid powder with adipoyl dichloride, with 2,2′-azobis[2-(2-imidazolyn-2-yl)propane] in the presence of pyridine: the amount of azo groups thus introduced onto the surface was determined to be 0.57 mmol/g by elemental analysis. It was found that the polymerizations of methyl methacrylate (MMA) and styrene were successfully initiated by the azo groups on the surface and that the corresponding polymers were grafted onto the surface. The percentage of surface grafting of polystyrene and poly(methyl methacrylate) (PMMA) increased up to 37.6 and 26.5%, respectively. Thermogravimetric analysis of polymer surface-grafted aramid powder confirmed that the grafting of polymers is limited on the surface. The polymerization rate was found to bear a first-order dependence on the concentration of aramid powder having azo groups. This suggests that in graft polymerization, unimolecular termination preferentially proceeds.