M-MOF-74吸附分离H2/He混合物的分子模拟研究

为了探究有机金属框架MOF-74能否作为一种优良的固体吸附剂,分离H₂/He混合物中H₂,并达到提纯He的目的,采用分子模拟的手段研究了H₂、He及H₂/He混合物在M-MOF-74（M=Mg、Co、Ni、Cu、Zn）上的吸附性能及吸附机理。结果表明,在1 bar（1 bar=10⁵ Pa）压力和25℃条件下,纯H₂对纯He在Ni-MOF-74上的选择性达6.58,而Mg-MOF-74对H₂的吸附量最大,其值为0.19 mmol·cm^-3,为He吸附量的6.46倍。当H₂/He混合物的浓度发生变化时,对其在M-MOF-74上的吸附分离因子没有较大影响,说明浓度变化不会影响M-MOF-74上吸附位点容纳H₂和He的能力。吸附位点和吸附热分析表明,MOF-74上的金属离子未饱和位点能够显著增强其对H₂的吸附能力。其结果对判断M-MOF-74是否具有分离H₂/He混合物的潜力,以及定量分析MOFs金属未饱和位点对H₂/He混合物分离的贡献提供了一定的理论基础。     

CO/N2/CO2在MOF-74(Ni)上吸附相平衡和选择性

主要研究了MOF-74(Ni)材料对CO/N₂/CO₂的吸附分离性能。应用水热法合成制备MOF-74(Ni),分别采用全自动表面积吸附仪、P-XRD、扫描电子显微镜对材料的孔隙结构和晶体形貌进行了表征,应用静态吸附法测定了CO、N₂和CO₂在MOF-74(Ni)上的吸附等温线,应用DSLF方程模拟了3种气体MOF-74(Ni)上的吸附等温线,依据IAST理论模型计算了MOF-74(Ni)对CO/N₂二元混合物和CO/CO₂二元混合物的吸附选择性。研究结果表明:在0.1 MPa和常温条件下,MOF-74(Ni)材料对CO吸附容量高达6.15 mmol·g^-1,而相同条件下N₂的吸附量只有0.86 mmol·g^-1。MOF-74(Ni)在低压下(0～40 kPa)对CO的吸附量明显高于其对CO₂的吸附量。应用IAST模型估算MOF-74(Ni)对二元混合物吸附选择性的结果表明:MOF-74(Ni)对CO/N₂混合物的吸附选择性在1000以上;MOF-74(Ni)对CO/CO₂的吸附选择性在4～9范围,在所研究的二元气体混合物吸附体系中,MOF-74(Ni)都能优先吸附CO。     

温度对MOF-74(Ni)吸附分离丙烯丙烷机理和选择性的影响

采用水热法成功制备了MOF-74(Ni),使用PXRD、孔径分析对材料进行了表征,测定了材料在不同温度下的C₃H₆和C₃H₈吸附等温线,应用程序升温脱附技术估算了脱附活化能,并使用IAST理论预测了材料对C₃H₆/C₃H₈二元体系的吸附选择性。讨论了温度对吸附机理和吸附选择性的影响。结果显示,MOF-74(Ni)的BET比表面积高达1306 m²·g^-1。在298 K下,C₃H₆的吸附量高达7.4 mmol·g^-1。随着温度升高,C₃H₈的吸附量大幅降低,而C₃H₆的吸附量下降程度较小,导致材料对C₃H₆/C₃H₈吸附选择性升高。当温度为328K时,MOF-74(Ni)对C₃H₆/C₃H₈二元气体混合物的吸附选择接近12。程序升温脱附的实验结果显示,C₃H₆在MOF-74(Ni)上的脱附活化能大于C₃H₈,分别为68.92 kJ·mol^-1和50.80 kJ·mol^-1。C₃H₆是通过与MOF-74(Ni)的不饱和金属位点Ni²⁺以p络合作用方式吸附,作用力较强,而C₃H₈与Ni²⁺之间的作用力较弱。根据吸附机理不同的特点,适当提高温度,将有助于提高MOF-74(Ni)吸附分离C₃H₆/C₃H₈混合物体系的吸附选择性。     

低湿CO2/H2O混合气体吸附特性实验

CO₂捕集、封存及利用是实现“双碳”目标的重要途径,为将碳捕集后的低湿CO₂/H₂O进行CO₂提纯和资源化利用,采用动态吸附实验研究了不同温度（303K、313K）、H₂O含量（0.7%~3.0%）的CO₂/H₂O在活性炭、活性氧化铝、分子筛3A和13X四种吸附剂上的动态吸附穿透曲线、吸附床温度分布、吸附量,分析了CO₂/H₂O分离系数和吸附热。结果表明,在CO₂/H₂O动态吸附过程中,吸附床温度与各组分浓度随时间变化趋势相同。H₂O饱和时间随进气温度升高而缩短;H₂O含量增加,抑制CO₂吸附;活性炭和氧化铝中H₂O的饱和时间随H₂O含量增加而增长,但分子筛3A和13X饱和时间缩短。H₂O吸附量随H₂O含量增加而增加,吸附热随吸附量增加而减小,CO₂则相反。分子筛3A对CO₂吸附量最小且CO₂/H₂O分离系数最大。H₂O含量小于1%时,CO₂吸附量最大的分子筛13X分离系数大于活性氧化铝,分子筛3A和13X适合分离低湿CO₂/H₂O。     

快速变压吸附制氢工艺的模拟与分析

目前工业上主要通过变压吸附技术从蒸汽甲烷重整气中制取氢产品气。然而,能源需求量的快速增加使得传统变压吸附技术在产量方面的不足越发明显。为此,进行了快速变压吸附从蒸汽甲烷重整气中制取氢气的模拟研究。采用活性炭和5A分子筛作为吸附剂,并以测得的原料气中各组分在两种吸附剂上的吸附数据为基础,进行了六塔快速变压吸附工艺的数值模拟与分析。在分析了塔内温度、压力和固相的浓度分布后,探究了进料流量、双层吸附剂高度比以及冲洗进料比三个操作参数对于快速变压吸附工艺性能的影响,结果表明：原料气组成为H₂/CH₄/CO/CO₂=76%/3.5%/0.5%/20%,吸附压力为22 bar（1 bar=10⁵ Pa）,解吸吹扫压力为1.0 bar,处理量为0.8875 mol·s^-1,吸附剂床层高度比为0.5∶0.5,冲洗进料比为22.37%时,可获得H₂纯度99.90%,回收率69.88%,此时H₂产量为0.4713 mol·s^-1。相比之下,氢气纯度为99.90%时,尽管PSA工艺回收率为83.40%,但处理量只有0.39 mol·s^-1,因此H₂产量仅为0.2472 mol·s^-1。     

交联淀粉负载氢氧化镁复合材料对Cu2+的吸附性能

以交联淀粉和MgSO₄·7H₂O为原料，NaOH为碱化剂，制备了交联淀粉负载氢氧化镁复合材料IStMg(OH)₂，采用FTIR、SEM、EDS、XRD对其进行了表征，并将其用于对模拟废水中Cu²⁺的吸附去除，考察了IStMg(OH)₂投加量、pH、Cu²⁺初始浓度等因素对ISt-Mg(OH)₂吸附Cu²⁺性能的影响。结果表明，当Cu²⁺质量浓度为20mg/L,pH=5.32,ISt-Mg(OH)₂投加量为300 mg/L，吸附温度为25 ℃时，Cu²⁺的去除率可达91.7%。吸附等温线拟合结果表明，ISt-Mg(OH)₂对水中Cu²⁺的吸附过程符合Langumir吸附模型，为单分子层吸附过程，在25 ℃时，拟合饱和吸附量为82.78 mg/g。吸附动力学数据拟合结果表明，吸附过程符合准二级动力学模型，属于...     

规整复合吸附剂真空变压吸附分离CH4/N2工艺模拟与分析

为减少甲烷排放,实现低浓度煤层气有效资源化利用,探究了使用规整复合吸附剂真空变压吸附富集低浓度煤层气的工艺。采用静态容积法测定了甲烷、氮气在规整复合吸附剂上的吸附等温线,同时建立了包括质量、热量和动量守恒在内的严格吸附床数学模型,设计了三塔连续进料的真空变压吸附工艺并进行模拟。分析了工艺达到循环稳态后吸附床层轴向温度分布和压力变化,并且探究了进料量、解吸压力、原料气中甲烷浓度和吸附压力对纯度、回收率、工艺能耗和吸附剂产率等工艺性能的影响。模拟结果表明,在进料量为100 L·min^-1,解吸压力为0.1 bar（1 bar=0.1 MPa）,原料气甲烷浓度为30%,吸附压力为3 bar时可以生产纯度为59.07%,回收率为93.64%的富CH₄产品气,同时单位能耗为18.70 kJ·mol^-1,吸附剂产率为4.56 mol·h^-1·kg^-1。表明规整吸附剂对CH₄/N₂具有良好的吸附分离效果,能够实现低浓度煤层气中甲烷高效富集。     

Co-MOF-74的合成及其吸附正己烷/1-己烯性能

采用溶剂热方法合成了Co-MOF-74,采用X射线衍射（XRD）、氮气吸附、红外光谱（FTIR）、热重-差热分析（TG-DSC）和扫描电子显微镜（SEM）对其进行表征,研究其吸附正己烷/1-己烯性能。结果表明,优化的Co-MOF-74合成工艺条件为：原料配比n[Co（NO₃）₂·6H₂O]：n（DHTP）：n（THF）：n（H₂O）=2：1：165：750,晶化温度100℃,晶化时间24h,150℃活化2h。合成Co-MOF-74对1-己烯和正己烷的静态饱和吸附量分别为125.6mg/g和72.9mg/g,BET比表面积为1209m²/g,孔体积为0.41cm³/g,微孔平均孔径为0.66nm。L-F吸附模型能较好地解释Co-MOF-74材料对1-己烯的吸附等温线数据,Co-MOF-74吸附1-己烯的过程是热力学自发放热过程。     

面向生物甲烷分离的不同金属配位金属-有机骨架材料的分子设计

采用巨正则Monte Carlo法（GCMC）,对CH₄ /CO₂混合气体体系基于金属-有机骨架材料（MOFs）的吸附分离进行了模拟研究。吸附分离材料涉及3个系列（M-MOF-74、M-MIL-53和[M（atz）（bdc）_0.5]）（M=Mg,Co,Ni,Zn,Al,Cr）不同金属配位的8种MOF材料。研究表明,Mg-MOF-74的CO₂吸附性能在高压下优于其他材料;在低压时,拥有大量氨基官能团的[Zn（atz）（bdc）_0.5]和[Co（atz）（bdc）_0.5]材料有更高效的CO₂分离性能。通过径向分布函数和CO₂吸附构型快照重叠图进一步分析发现,各个系列材料不同金属配位对CO₂吸附构型的影响造成了材料吸附分离性能有较大的不同。研究结果能够为实验上设计和开发新型高效CO₂和CH₄吸附分离MOFs材料提供启发。     

H2SO4改性TiO2光催化处理钻井废水

通过H₂SO₄改性制备了TiO₂光催化剂,采用XRD和激光粒度仪进行表征,研究了H₂SO₄浸泡浓度、光照时间、pH和氧化剂H₂O₂用量对钻井废水进行光催化处理的影响。结果表明,H₂SO₄改性并未改变TiO₂晶体结构,在钻井废水水样pH=6、H₂SO₄改性TiO₂用量15 g·L^-1、光照时间30 min和氧化剂H₂O₂用量1.0 mL条件下,钻井废水的COD值降为2 mg·L^-1,符合国家污水排放标准。     

Understanding the mechanism of hydrogen adsorption into metal organic frameworks

Hydrogen adsorption mechanism into MOF-5, a porous metal-organic framework (MOF) has been studied by density functional theory calculation. The selected functionals for the prediction of interaction energies between hydrogen and potential adsorption sites of MOF-5 were utilized after the evaluation with the various functionals for interaction energy of H₂C₆H₆ model system. The adsorption energy of hydrogen molecule into MOF-5 was investigated with the consideration of the favorable adsorption sites and the orientations. We also calculated the second favorable adsorption sites by geometry optimization using every combination of two first adsorbed hydrogen molecules. Based on the calculation of the first and the second adsorption sites and energies, it has been suggested that the hydrogen adsorption into MOF-5 follows a cooperative mechanism in which the metal sites initiate the propagation of the hydrogen adsorption on the whole frameworks. In addition, the interaction mode between the simple benzene ring with hydrogen is significantly changed when the benzene ring has been incorporated into the framework of MOF-5.     

高温煤焦气化反应的Langmuir-Hinshelwood动力学模型

应用基于吸附和脱附原理的Langmuir-Hinshelwood （L-H） 动力学模型来描述煤焦在H₂O和CO₂混合气氛下的气化反应时,存在单独活性位和相同活性位两个相互矛盾的假设。在管式炉实验装置内考察了在不同气化温度和气化剂分压的条件下,内蒙煤焦（NMJ）与H₂O和CO₂的气化反应特性,获得了NMJ-H₂O 和NMJ-CO₂反应的L-H动力学模型,同时考察了H₂、CO对煤焦气化反应的抑制作用,并探究了NMJ在H₂O和CO₂混合气氛下的气化反应机理。研究结果表明：NMJ-H₂O以及NMJ-CO₂反应的活化能分别为214.78 kJ·mol^-1和145.96 kJ·mol^-1。H₂对NMJ-H₂O以及CO对NMJ-CO₂的反应存在明显的抑制作用,且CO的抑制作用随反应温度的降低而愈加明显。基于L-H动力学模型计算得到的反应速率曲线与实验结果十分吻合。对于NMJ在H₂O和CO₂混合气氛下的气化反应,基于相同活性位假设的L-H模型的反应速率预测值与实验结果吻合,更加适用于NMJ在混合气氛下的气化反应机理。     

面向氢气/甲烷分离分子筛膜微结构调控的研究进展

氢能具有燃烧值高、零碳排放等优势,发展氢能技术是实现“碳达峰、碳中和”战略的重要举措。当前,基于天然气和石油路线的制氢均存在将氢气从甲烷等烃分子中分离的过程。氢气/甲烷分离主要有变压吸附法、深冷精馏法以及膜分离法。分子筛膜具有精准分子筛分、高分离性能和稳定性好等优势,是低能耗分离氢气/甲烷最具发展潜力的膜材料。面向氢气/甲烷分离的应用需求,阐述了沸石分子筛膜和MOFs分子筛膜微结构调控策略、氢气/甲烷分离性能和构效关系的研究现状,分析了分子筛膜材料在氢气/甲烷分离领域的机遇和挑战。绘制了可与2008年聚合物膜Robeson上限图相比的分子筛膜性能数据图,并预测了分子筛膜在制氢分离领域经济可行的分离性能目标区域。     

Silicalite-1 zeolite composite membranes

This review paper discusses the preparation of silicalite-1 zeolite membranes, the experimental procedures used for gas separation measurements and the results of single gas and gas mixture experiments. Silicalite-alumina composite membranes were prepared by an in-situ zeolite synthesis method using an alumina membrane tube with a 5-nm-pore-diameter, γ-alumina layer as a substrate. Single gas permeances of H₂, Ar, n-C₄H₁₀, i-C₄H₁₀ and SF₆ were measured and mixtures of H₂/i-C₄H₁₀ and H₂/SF₆ were separated to characterize the silicalite membrane. These measurements were made from 300 to 737 K. Transport through the silicalite membrane appeared to be controlled by molecular size and adsorption properties. Permeances of all components studied were activated, and activation energies ranged from 8.5 to 16.2 kJ/mol. The ratio of single gas permeances was as high as 136 for H₂/SF₆ and 1100 for H₂/i-C₄H₁₀ at 298 K. Separation selectivities at elevated temperatures were significantly above Knudsen diffusion selectivity and were larger than ratios of pure gas permeances at the same temperature. The largest permeance ratio for the separation of mixtures was 12.8 for H₂/SF₆ at 583 K. Separation selectivities were higher when a pressure drop was maintained across the membrane than when an inert sweep gas was used because of counter diffusion of the sweep gas.     

Effects of zeolite structure and aluminum content on thiophene adsorption, desorption, and surface reactions

The adsorption and desorption of thiophene and the reactions of thiophene-derived adsorbed species in He, H₂, and O₂ were examined on H-ZSM5, H-Beta, and H-Y with varying Si/Al ratios. Thiophene adsorption uptakes (per Al) were independent of Al content, but were above unity and influenced by zeolite structure (1.7, 2.2, and 2.9 on H-ZSM5, H-Beta, and H-Y). These data indicate that thiophene oligomers form during adsorption and that their size depends on spatial constraints within zeolite channels. Adsorption and oligomerization occur on Brønsted acid sites at 363 K. Thiophene/toluene adsorption from their mixtures show significant thiophene selectivity ratios (10.3, 7.9, and 6.4, for H-ZSM5, H-Beta, and H-Y zeolites), which exceed those expected from van der Waals interactions and reflect specific interactions with Brønsted acid sites and formation of toluene–thiophene reaction products. Treatment of thiophene-derived adsorbed species above 363 K in He or H₂ led to depolymerization of thiophene oligomers and to the formation of unsaturated adsorbed species with a 1:1 thiophene/Al stoichiometry on all zeolites and at all Si/Al ratios. These unsaturated species desorb as stable molecules, such as H₂S, hydrocarbons, and larger organosulfur compounds, formed via ring opening and hydrogen transfer from H₂ or co-adsorbed species, and also form stranded unsaturated organic deposits. Smaller channels and higher Al contents preferentially formed H₂S, benzotiophenes, and arene products during treatment in He or H₂, as a result of diffusion-enhanced of secondary reactions of desorbed thiophene molecules with adsorbed thiophene-derived species. Only oxidative regeneration treatments led to full recovery of thiophene uptake capacities. A preceding treatment in H₂, however, led to the partial recovery of thiophene-derived carbon atoms as useful hydrocarbons and decreased the amount of CO₂ and SO₂ formed during subsequent oxidative treatments required for regeneration.