Design of a Compact Monopole Antenna for UWB Applications

In this paper, a low cost, highly efficient and low profile monopole antenna for ultra-wideband (UWB) applications is presented. A new inverted triangular-shape structure possessing meander lines is designed to achieve a wideband response and high efficiency. To design the proposed structure, three steps are utilized to achieve an UWB response. The bandwidth of the proposed antenna is improved with changing meander lines parameters, miniaturization of the ground width and optimization of the feeding line. The measured and simulated frequency band ranges from 3.2 to 12 GHz, while the radiation patterns are measured at 4, 5.3, 6 and 8 GHz frequency bands. The overall volume of the proposed antenna is 26 × 25 × 1.6 mm3 ; whereas the FR4 material is used as a substrate with a relative permittivity and loss tangent of 4.3 and 0.025, correspondingly. The peak gain of 4 dB is achieved with a radiation efficiency of 80 to 98% for the entire wideband. Design modelling of proposed antenna is performed in ANSYS HFSS 13 software. A decent consistency between the simulated and measured results is accomplished which shows that the proposed antenna is a potential candidate for the UWB applications.     

A Novel Compact Highly Isolated UWB MIMO Antenna with WLAN Notch

This paper presents a compact Multiple Input Multiple Output (MIMO) antenna with WLAN band notch for Ultra-Wideband (UWB) applications. The antenna is designed on 0.8 mm thick low-cost FR-4 substrate having a compact size of 22 mm × 30 mm. The proposed antenna comprises of two monopole patches on the top layer of substrate while having a shared ground on its bottom layer. The mutual coupling between adjacent patches has been reduced by using a novel stub with shared ground structure. The stub consists of complementary rectangular slots that disturb the surface current direction and thus result in reducing mutual coupling between two ports. A slot is etched in the radiating patch for WLAN band notch. The slot is used to suppress frequencies ranging from 5.1 to 5.9 GHz. The results show that the proposed antenna has a very good impedance bandwidth of |S11| < −10 dB within the frequency band from 3.1–14 GHz. A low mutual coupling of less than −23 dB is achieved within the entire UWB band. Furthermore, the antenna has a peak gain of 5.8 dB, low ECC < 0.002 and high Diversity Gain (DG > 9.98).     

A Compact Rhombus Shaped Antenna with Extended Stubs for Ultra-Wideband Applications

Ultra-wideband (UWB) is highly preferred for short distance communication. As a result of this significance, this project targets the design of a compact UWB antennas. This paper describes a printed UWB rhombus-shaped antenna with a partial ground plane. To achieve wideband response, two stubs and a notch are incorporated at both sides of the rhombus design and ground plane respectively. To excite the antenna, a simple microstrip feed line is employed. The suggested antenna is built on a 1.6 mm thick FR4 substrate. The proposed design is very compact with overall electrical size of 0.18λ × 0.25λ (14 × 18 mm²). The rhombus shaped antenna covers frequency ranging from 3.5 to 11 GHz with 7.5 GHz impedance bandwidth. The proposed design simulated and measured bandwidths are 83.33% and 80%, respectively. Radiation pattern in terms of E-field and H-field are discussed at 4, 5.5 and 10 GHz respectively. The proposed design has 65% radiation efficiency and 1.5 dBi peak gain. The proposed design is simulated in CST (Computer Simulation Technology) simulator and the simulated design is fabricated for the measured results. The simulated and measured findings are in close resemblance. The obtained results confirm the application of the proposed design for the ultra-wide band applications.     

V-Shaped Monopole Antenna with Chichena Itzia Inspired Defected Ground Structure for UWB Applications

Due to rapid growth in wireless communication technology, higher bandwidth requirement for advance telecommunication systems, capable of operating on two or higher bands with higher channel capacities and minimum distortion losses is desired. In this paper, a compact Ultra-Wideband (UWB) V-shaped monopole antenna is presented. UWB response is achieved by modifying the ground plane with Chichen Itzia inspired rectangular staircase shape. The proposed V-shaped is designed by incorporating a rectangle, and an inverted isosceles triangle using FR4 substrate. The size of the antenna is 25 mm×26 mm×1.6 mm. The proposed V-shaped monopole antenna produces bandwidth response of 3 GHz Industrial, Scientific, and Medical (ISM), Worldwide Interoperability for Microwave Access (WiMAX), (IEEE 802.11/HIPERLAN band, 5G sub 6 GHz) which with an additional square cut amplified the bandwidth response up to 8 GHz ranging from 3.1 GHz to 10.6 GHz attaining UWB defined by Federal Communications Commission (FCC) with a maximum gain of 3.83 dB. The antenna is designed in Ansys HFSS. Results for key performance parameters of the antenna are presented. The measured results are in good agreement with the simulated results. Due to flat gain, uniform group delay, omni directional radiation pattern characteristics and well-matched impedance, the proposed antenna is suitable for WiMAX, ISM and heterogeneous wireless systems.     

Metamaterial-Based Compact Antenna with Defected Ground Structure for 5G and Beyond

In this paper, a unit cell of a single-negative metamaterial structure loaded with a meander line and defected ground structure (DGS) is investigated as the principle radiating element of an antenna. The unit cell antenna causes even or odd mode resonances similar to the unit cell structure depending on the orientation of the microstrip feed used to excite the unit cell. However, the orientation which gives low-frequency resonance is considered here. The unit cell antenna is then loaded with a meander line which is parallel to the split bearing side and connects the other two sides orthogonal to the split bearing side. This modified structure excites another mode of resonance at high frequency when a meander line defect is loaded on the metallic ground plane. Specific parameters of the meander line structure, the DGS shape, and the unit cell are optimized to place these two resonances at different frequencies with proper frequency intervals to enhance the bandwidth. Finally, the feed is placed in an offset position for better impedance matching without affecting the bandwidth The compact dimension of the antenna is 0.25 λL × 0.23 λL × 0.02 λL, where λL is the free space wavelength with respect to the center frequency of the impedance bandwidth. The proposed antenna is fabricated and measured. Experimental results reveal that the modified design gives monopole like radiation patterns which achieves a fractional operating bandwidth of 26.6%, from 3.26 to 4.26 GHz for |S11|<−10 dB and a pick gain of 1.26 dBi is realized. In addition, the simulated and measured cross-polarization levels are both less than −15 dB in the horizontal plane.     

Broadband flexible comb-shaped monopole antenna

A broadband comb-shaped monopole antenna is proposed. The antenna has dimensions of 19 mm x 12 mm. The measured results show good agreement with the numerical prediction, and broadband operation with 10 dB impedance bandwidth of 44.75% (1.7-2.68 GHz). The antenna is built on one side of a flexible-printed circuit board (PCB) dielectric substrate. Folded and rolled antenna structures, which are transformed by the proposed planar antenna structure, are presented. Each antenna has a broadband impedance bandwidth that covers the PCS, UMTS, WiBro, WLAN and SDMB bands. Also, omni-directional radiation patterns over the operating bands have been obtained. The proposed antennas are suitable for mobile communication applications requiring a small antenna.     

新型古币形超宽带分形印刷天线的设计

共面波导和分形结构结合应用,在展宽天线带宽方面具有独特优势.提出了一种新型古币形超宽带分形天线,采用共面波导馈电,并加载分形缝隙,天线的阻抗带宽大幅提高.给出了天线的表面电流、回波损耗、方向图和增益结果.对3阶分形天线进行了加工与测试,测试结果表明,天线带宽达到2.6～16 GHz,带宽比大于6:1.仿真结果与测试结果基本吻合,为超宽带小型化天线的设计提供了新的思路．     

Ultra-wideband quasi-circular monopole antennas with rectangular and trapezoidal grounds

Two planar quasi-circular monopole antennas with rectangular and trapezoidal grounds are presented. The impedance bandwidths of the two antennas, defined by measured return loss better than 10 dB, are from 1.3 to 18.4 GHz and from 1.1 to 13.5 GHz, respectively. Both numerical and experimental results show that the proposed antenna with trapezoidal ground has significantly improved radiation performance, compared with the one with rectangular ground. Parameters and design considerations of the trapezoidal ground are discussed in detail. These novel monopole antennas have very wide impedance bandwidth, compact size and low fabrication cost, which are suitable for various broadband applications.     

Compact coplanar waveguide-fed ultra-wideband monopole-like slot antenna

A simple and compact coplanar waveguide (CPW)-fed ultra-wideband (UWB) monopole-like slot antenna is presented. The proposed antenna comprises a monopole-like slot and a CPW fork-shaped feeding structure, which is etched onto an FR4 printed circuit board (PCB) with an overall size of 26 mm x 29 mm x 1.5 mm. The simulation and experiment show that the proposed antenna achieves good impedance matching, consistent gain, stable radiation patterns and consistent group delay over an operating bandwidth of 2.7?12.4 GHz (128.5%). Furthermore, through adding two more grounded open-circuited stubs, the proposed antenna design features band-notched characteristic in the band of 5?6 GHz while maintaining the desirable performance over lower/upper UWB bands of 3.1?4.85 GHz/6.2?9.7 GHz.     

Small modified monopole antenna for UWB application

In this paper, we present a novel modified printed monopole antenna (PMA) for ultra-wideband (UWB) applications. The proposed antenna consists of a truncated ground plane and radiating patch with two tapered steps, which provides wideband behaviour and relatively good matching. Moreover, the effects of a modified trapezoid-shaped slot inserted in the radiating patch, on the impedance matching and radiation behaviour is investigated. The antenna has a small area of 14 x 20 mm² and offers an impedance bandwidth as high as 100% at a centre frequency of 7.45 GHz for S₁₁ < -10 dB, which has a frequency bandwidth increment of 18% with respect to the previous similar antenna. Simulated and experimental results obtained for this antenna show that it exhibits good radiation behaviour within the UWB frequency range.     

Inkjet Printed Metamaterial Loaded Antenna for WLAN/WiMAX Applications

In this paper, the design and performance analysis of an Inkjet-printed metamaterial loaded monopole antenna is presented for wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) applications. The proposed metamaterial structure consists of two layers, one is rectangular tuning fork-shaped antenna, and another layer is an inkjet-printed metamaterial superstate. The metamaterial layer is designed using four split-ring resonators (SRR) with an H-shaped inner structure to achieve negative-index metamaterial properties. The metamaterial structure is fabricated on low-cost photo paper substrate material using a conductive ink-based inkjet printing technique, which achieved dual negative refractive index bands of 2.25–4.25 GHz and 4.3–4.6 GHz. The antenna is designed using a rectangular tuning fork structure to operate at WLAN and WiMAX bands. The antenna is printed on 30 × 39 × 1.27 mm3 Rogers RO3010 substrate, which shows wide impedance bandwidth of 0.75 GHz (2.2 to 2.95 GHz) with 2 dB realized gain at 2.4 GHz. After integrating metamaterial structure, the impedance bandwidth becomes 1.25 GHz (2.33 to 3.58 GHz) with 2.6 dB realized gain at 2.4 GHz. The antenna bandwidth and gain have been increased using developed quad SRR based metasurface by 500 MHz and 0.6 dBi respectively. Moreover, the proposed quad SRR loaded antenna can be used for 2.4 GHz WLAN bands and 2.5 GHz WiMAX applications. The contribution of this work is to develop a cost-effective inject printed metamaterial to enhance the impedance bandwidth and realized the gain of a WLAN/WiMAX antenna.     

A Compact Dual-Port Multi-Band Rectifier Circuit for RF Energy Harvesting

This paper presents a compact multi-band rectifier with an improved impedance matching bandwidth. It uses a combination of п–matching network (MN) at Port-1, with a parallel connection of three cell branch MN at Port-2. The proposed impedance matching network (IMN) is adopted to reduce circuit complexity, to improve circuit performance, and power conversion efficiency (PCE) of the rectifier at low input power. The fabricated rectifier prototype operates at 0.92, 1.82, 2.1, 2.46 and 2.65 GHz covering GSM/900, GSM/1800, UMTS2100, and Wi-Fi/2.45–LTE2600. The size of the compact rectifier on the PCB board is 0.13λ_g × 0.1λ_g. The fabricated rectifier achieved an RF-to DC (radio frequency direct current) PCE of 31.8%, 24%, 22.7%, and 15%, and 14.1% for −20 dBm at the five respective measured operating frequencies. The circuit attains a peak RF-to-DC PCE of 82.3% for an input power of 3 dBm at 0.92 GHz. The proposed rectifier realizes an ambient output dc voltage of 454 mV for multi-tone input signals from the two ports. The rectifier drives a bq25504-674 power management module (PMM) to achieve 1.21 V from the two-port connection. The rectifier has the ability to exploit both frequency domain through the multi-band operation with good impedance bandwidth and a spatial domain using dual-port configuration. Hence, it is a potential candidate for various applications in radio frequency energy harvesting (RFEH) system.     

Dual frequency band antenna combined with a high impedance band gap surface

A compact dual-band antenna structure for automotive and aerospace applications is discussed. A bow tie dual-band electromagnetic band gap (EBG) element geometry is presented that has a reduced cell dimension compared to the wavelength yet has sufficient bandwidth for mobile communication applications. The EBG was combined with a printed planar monopole to produce a structure 8 mm thick. The return loss and radiation patterns gave satisfactory performance at two frequency bands with bandwidths of 11% at 1700 MHz and 7% at 2600 MHz. There was suppression of the back radiation at both bands of 5 dB or better even for the small 3 times 3 element EBG used and the antenna was platform tolerant.     

Zero-Index Metamaterial Superstrates UWB Antenna for Microwave ImagingDetection

Metamaterials (MTM) can enhance the properties of microwaves and also exceed some limitations of devices used in technical practice. Note that the antenna is the element for realizing a microwave imaging (MWI) system since it is where signal transmission and absorption occur. Ultra-Wideband (UWB) antenna superstrates with MTM elements to ensure the signal transmitted from the antenna reaches the tumor and is absorbed by the same antenna. The lack of conventional head imaging techniques, for instance, Magnetic Resonance Imaging (MRI) and Computerized Tomography (CT)-scan, has been demonstrated in the paper focusing on the point of failure of these techniques for prompt diagnosis and portable systems. Furthermore, the importance of MWI has been addressed elaborately to portray its effectiveness and aptness for a primary tumor diagnosis. Other than that, MTM element designs have been discussed thoroughly based on their performances towards the contributions to the better image resolution of MWI with detailed reasonings. This paper proposes the novel design of a Zeroindex Split Ring Resonator (SRR) MTM element superstrate with a UWB antenna implemented in MWI systems for detecting tumor. The novel design of the MTM enables the realization of a high gain of a superstrate UWB antenna with the highest gain of 5.70 dB. Besides that, the MTM imitates the conduct of the zeroreflection phase on the resonance frequency, which does not exist. An antenna with an MTM unit is of a 7 × 4 and 10 × 5 Zero-index SRR MTM element that acts as a superstrate plane to the antenna. Apart from that, Rogers (RT5880) substrate material is employed to fabricate the designed MTM unit cell, with the following characteristics: 0.51 mm thickness, the loss tangent of 0.02, as well as the relative permittivity of 2.2, with Computer Simulation Technology (CST) performing the simulation and design. Both MTM unit cells of 7 × 4 and 10 × 5 attained 0° with respect to the reflection phase at the 2.70 GHz frequency band. The first design, MTM Antenna Design 1, consists of a 7 × 4 MTM unit cell that observed a rise of 5.70 dB with a return loss (S11) −20.007dB at 2.70 GHz frequency. The second design, MTM Antenna Design 2, consists of 10 × 5 MTM unit cells that recorded a gain of 5.66 dB, having the return loss (S11) −19.734 dB at 2.70 GHz frequency. Comparing these two MTM elements superstrates with the antenna, one can notice that the 7 × 4 MTM element shape has a low number of the unit cell with high gain and is a better choice than the 10 × 5 MTM element in realizing MTM element superstrates antenna for MWI.     

Optimised small-size tapered monopole antenna for pulsed ultra-wideband applications designed by a genetic algorithm

An optimised small-size printed tapered monopole antenna, PTMA, is designed for ultra-wideband applications. Optimisation is based on a real-coded version of Harik?s compact genetic algorithm, RCCGA. The optimisation algorithm, RCCGA has lowered the antenna area by more than 48% compared with the previous work for 3.1 to 11.7 GHz bandwidth operation. The time- and frequency-domain performance of the antenna are also described in simulations and measurements     

A Compact Flexible Circularly Polarized Implantable Antenna forBiotelemetry Applications

With the help of in-body antennas, the wireless communication among the implantable medical devices (IMDs) and exterior monitoring equipment, the telemetry system has brought us many benefits. Thus, a very thin-profile circularly polarized (CP) in-body antenna, functioning in ISM band at 2.45 GHz, is proposed. A tapered coplanar waveguide (CPW) method is used to excite the antenna. The radiator contains a pentagonal shape with five horizontal slits inside to obtain a circular polarization behavior. A bendable Roger Duroid RT5880 material (ε_r = 2.2, tanδ = 0.0009) with a typical 0.25 mm-thickness is used as a substrate. The proposed antenna has a total volume of 21 × 13 × 0.25 mm³. The antenna covers up a bandwidth of 2.38 to 2.53 GHz (150 MHz) in vacuum, while in skin tissue it covers 1.56 to 2.72 GHz (1.16 GHz) and in the muscle tissue covers 2.16 to 3.17 GHz (1.01 GHz). GHz). The flexion analysis in the x and y axes was also performed in simulation as the proposed antenna works with a wider bandwidth in the skin and muscle tissue. The simulation and the curved antenna measurements turned out to be in good agreement. The impedance bandwidth of −10 dB and the axis ratio bandwidth of 3 dB (AR) are measured on the skin and imitative gel of the pig at 27.78% and 35.5%, 13.5% and 4.9%, respectively, at a frequency of 2.45 GHz. The simulations revealed that the specific absorption rate (SAR) in the skin is 0.634 and 0.914 W/kg in muscle on 1g-tissue. The recommended SAR values are below the limits set by the federal communications commission (FCC). Finally, the proposed low-profile implantable antenna has achieved very compact size, flexibility, lower SAR values, high gain, higher impedance and axis ratio bandwidths in the skin and muscle tissues of the human body. This antenna is smaller in size and a good applicant for application in medical implants.     

Frequency Reconfigurable Antenna for Portable Wireless Applications

In this paper, the design and experimental evaluation of a hexagonal-shaped coplanar waveguide (CPW)-feed frequency reconfigurable antenna is presented using flame retardant (FR)-4 substrate with size of 37 × 35 × 1.6 mm³. The antenna is made tunable to three different modes through the status of two pin diodes to operate in four distinct frequency bands, i.e., 2.45 GHz wireless fidelity (Wi-Fi) in MODE 1, 3.3 GHz (5G sub-6 GHz band) in MODE 2, 2.1 GHz (3G Long Term Evolution (LTE)-advanced) and 3.50 GHz Worldwide Interoperability for Microwave Access (WiMAX) in MODE 3. The optimization through simulation modeling shows that the proposed antenna can provide adequate gain (1.44~2.2 dB), sufficient bandwidth (200~920 MHz) and high radiation efficiency (80%~95%) in the four resonating frequency bands. Voltage standing wave ratio (VSWR) < 1.5 is achieved for all bands with properly matched characteristics of the antenna. To validate the simulation results, fabrication of the proposed optimized design is performed, and experimental analysis is found to be in a considerable amount of agreement. Due to its reasonably small size and support of multiple frequency bands operation, the proposed antenna can support portable devices for handheld 5G and Wireless LAN (WLAN) applications.     

Compact Interlaced Dual Circularly Polarized Sequentially Rotated Dielectric-Resonator Antenna Array

In this study, a compact 2 × 2 interlaced sequentially rotated dual-polarized dielectric-resonator antenna array is proposed for 5.8 GHz applications. The array is composed of a novel unit elements that are made of rectangular dielectric resonator (RDR) coupled to an eye slot for generating the orthogonal modes, and to acquire circular polarization (CP) radiation. For the purpose of miniaturization and achieving dual polarized resonance, the array is fed by two interlaced ports and each port excites two radiating elements. The first port feeds horizontal elements to obtain left hand circular polarization (LHCP). The second port feeds vertical elements to obtain right hand circular polarization (RHCP). A quarter-wave length transformer is employed to reduce the attenuation and consequently increase the array gain performance. The 35 × 35 mm² () gains were 8.4 and 8.2 dBi for port 1 and port 2, respectively, with port isolations of −33.51 dB. The design achieves a voltage standing-wave ratio (VSWR) < −10 dB and an axial ratio (AR) ˂ − 3 dB bandwidth of 2.48% (5.766 to 5.911 GHz) for LHCP at port 1 and a VSWR < −10 dB and AR ˂ −3 dB bandwidth of 2.28% (5.788 to 5.922 GHz) for RHCP at port 2. The findings of the proposed design validate its use for ISM band applications.     

一种改善超宽带MIMO天线隔离性能的方法

多输入多输出(Multiple-InputMultiple-Output,MIMO)技术是现代通信技术的发展趋势,为移动通信的迅速更迭提供了极大支持.设计了一种二端口的超宽带MIMO天线,其-10 dB阻抗带宽从3.3 GHz扩展到9.1 GHz.通过在天线接地板上蚀刻一条宽缝隙,并在其中添加音叉型枝节,改善了超宽带M...     

Dual wideband coplanar waveguide-fed notched antennas with asymmetrical grounds for multi-band wireless application

A novel single-layer planar monopole antenna is proposed for dual wideband operation. The antenna is a notched patch fed by a coplanar waveguide with two asymmetrical ground planes. The parametrical effects of the size of two such grounds and an embedded notch on the impedance matching condition have been examined theoretically. By fabricating and measuring the prototypes of the proposed antenna, two bands with 10 dB return loss bandwidths of about 490 MHz centred at 2.13 GHz band and of about 99.2% ranging from 3.32 to 6.9 GHz were obtained. A stable radiation pattern and average gains of greater than 2.6 and 4.8 dBi, respectively, over the two operating bands have also been obtained. These properties make the antenna suitable for multi-frequency wireless operation.