制备条件对Ni2P/TiO2-Al2O3催化剂加氢脱硫性能的影响

采用溶胶-凝胶法制备了TiO₂-Al₂O₃复合载体, 以柠檬酸为络合剂, 浸渍法制备了负载型Ni₂P/TiO₂-Al₂O₃催化剂前体, 程序升温H₂还原法制备了Ni₂P/TiO₂-Al₂O₃催化剂, 并用 X 射线衍射(XRD)、N₂吸附比表面积(BET)测定技术对催化剂的结构和性质进行了表征, 考察了浸渍方法、Ni/P摩尔比、Ni₂P负载量对其进行的二苯并噻吩(DBT)加氢脱硫(HDS)性能的影响。结果表明, 当Ni/P比低于1:1时, 能得到单一的Ni₂P物相;当Ni/P比为2:1时, 开始出现Ni₃P物相。采用Ni/P比为1:1、Ni₂P负载量为30%、采用共浸渍方法制备的Ni₂P/TiO₂-Al₂O₃催化剂具有最好的活性, 在360℃、3.0MPa、氢油比500 (体积比)、液时体积空速2.0h^-1的条件下反应4h时, 二苯并噻吩转化率为99.5%。     

Shape selective catalytic behaviors of nickel ion-exchanged layered potassium niobate

The alcohol decomposition and olefin hydrogenation on the hydrogen-treated Ni ion-exchanged (exchange degree, 30%) potassium niobate (Ni-K₄Nb₆O₁₇) were performed. Formation of propene from i-propanol on Ni-K₄Nb₆O₁₇ was much smaller than that observed on bulk Nb₂O₅, while the olefin yields from ethanol and n-propanol were almost the same on both catalysts. The 1- butene hydrogenation did not proceed on Ni-K₄Nb₆O₁₇, whereas propene hydrogenation took place rapidly on the same catalyst at 80°C.

The formation of the acid sites and Ni metallic sites by hydrogen treatment at 300 °C was proposed by using temperature-programmed reduction (TPR) and extended X-ray absorption fine structure (EXAFS). These results suggest that Hg₂-treated Ni-K₄Nb₆O₁₇ acts as a shape selective acid- and metal-catalyst at suitable reaction temperatures.     

甘油水蒸汽重整制氢Ni/Ce0.9Gd0.1O1.95催化剂的研究

采用浸渍法和共沉淀法制备了Ni质量分数10%的10%Ni/Ce_0.9Gd_0.1O_1.95催化剂,通过X射线衍射、N₂物理吸附与H₂脉冲化学吸附、H₂程序升温还原等技术表征了催化剂的结构和性质,并考察了其催化甘油水蒸汽重整制氢反应性能。结果表明,浸渍法制备的10%Ni/Ce_0.9Gd_0.1O_1.95-S催化剂的活性最佳,该催化剂上Ni晶粒小、分散度高,形成氧空穴使得催化剂抗积炭能力大大提高,所以活性、氢气选择性较高,稳定性也较好。同时考察了水与甘油物质的量比和泵流速对甘油重整反应性能的影响,发现在水与甘油物质的量比为24:1,泵流速为0.06 mL·min^-1的条件下,甘油几乎完全转化,氢气选择性也非常高,而且反应10 h没有失活。     

磷化镍催化异丁烷临氢脱氢制异丁烯

以SiO₂为载体,结合浸渍法和程序升温还原法制备磷化镍催化剂,考察了不同n(Ni)/n(P)和不同Ni负载量等对催化剂的结构及异丁烷脱氢性能的影响。运用透射电镜(TEM),X射线衍射(XRD),程序升温还原(H₂-TPR),氢气程序升温脱附(H₂-TPD)等表征手段考察催化剂的组成与结构、还原性能及氢吸附性能。研究结果表明:Ni/P比对催化剂表面的物相有较大影响,n(Ni)/n(P)为1.0和0.5时,形成Ni₂P相;n(Ni)/n(P)为1.5时,形成Ni₁₂P₅。随着Ni负载量的增加,活性组分Ni₂P粒子尺寸变大,但分散度降低。磷化镍能够催化异丁烷脱氢制异丁烯,但Ni₂P的催化活性要比Ni₁₂P₅高,经实验研究发现,当Ni/P比为1.0、负载量为10%、n(H₂)/n(i-C₄H₁₀)=1.0、空速为800 h^-1时,在460 ℃反应时,对异丁烯的选择性可达到80%。     

PREPARATION OF PEROVSKITE 0.75Pb(Ni1/3Nb2/3)O3-0.25PbTiO3 CERAMICS USING SEMICHEMICAL METHODS AND RELATED REACTION MECHANISMS

This article discusses a mechanism for preparing perovskite powders, 0.75Pb(Ni_1/3Nb_2/3)O₃-0.25PbTiO₃ (PNN-PT), using a semichemical method (SCM).Precursors were prepared by adding aqueous Ni(Ac)₂ solutions to an alcohol slurry of PbO, Nb₂O₅, and TiO₂. The TG-DTG and DSC analysis of the precursors and XRD analysis of the powders at different thermal treatment temperatures showed that the reaction mechanisms in this method differ from those in the conventional mixed-oxide method. The aqueous Ni(Ac)₂ solution reacted with PbO to form Pb(Ac)₂ · Pb(OH)₂ · H₂O and Ni(OH)₂, which decomposed to form nascent PbO and NiO, thereby improving the reactivity and distribution of PbO and NiO. Pb₃Nb₂O₈ and NiNb₂O₆ formed and were easily converted into the perovskite phase during the thermal treatment process. At a thermal treatment temperature of 850°C, the content of the perovskite phase reached 98%. Pyrochlore-free PNN-PT ceramic was obtained after 2 h of sintering at 1100°C, and its dielectric properties were found to be excellent at temperatures ranging between -55 and 120°C.     

Strong rhodium–niobia interaction in Rh/Nb2O5, Nb2O5–Rh/SiO2 and RhNbO4/SiO2 catalysts: Application to selective CO oxidation and CO hydrogenation

The extent of Rh–niobia interaction in niobia-supported Rh (Rh/Nb₂O₅), niobia-promoted Rh/SiO₂ (Nb₂O₅–Rh/SiO₂) and RhNbO₄/SiO₂ catalyst after H₂ reduction has been investigated by H₂ and CO chemisorption measurements. These catalysts have been applied to selective CO oxidation in H₂ (CO+H₂+O₂) and CO hydrogenation (CO+H₂), and the results are compared with those of unpromoted Rh/SiO₂ catalysts. It has been found that niobia (NbO_x) increases the activity and selectivity for both the reactions.     

载体对镍基催化剂顺酐液相加氢性能的影响

分别以ZrO₂、SiO₂与Al₂O₃为载体,采用等体积浸渍法制备了Ni质量分数为15%的催化剂,考察了其催化顺酐液相加氢性能,并利用BET、XRD、H₂-TPR以及TPO-MS等表征手段对催化剂进行了详细表征。结果表明,随载体不同各催化剂的加氢活性及选择性存在较大差异,Ni/Al₂O₃催化剂的C=C键加氢活性最高,但其几乎没有C=O加氢活性,催化顺酐加氢主产物为丁二酸酐。Ni/ZrO₂催化剂具有最高的C=O加氢活性,催化顺酐加氢主产物为γ-丁内酯,在反应温度为483 K,氢气压力为5 MPa的条件下反应8 h时,Ni/ZrO₂催化剂的γ-丁内酯选择性达79.20%。催化剂的套用实验表明,Ni/ZrO₂与Ni/SiO₂催化剂具有高的使用稳定性,Ni/Al₂O₃催化剂则在套用过程中快速失活。顺酐加氢至γ-丁内酯的中间产物--丁二酸酐与催化剂间的相互作用是影响催化剂加氢选择性及使用稳定性的主要原因。     

Activity and acidity of Nb2O5-MoO3 and Nb2O5-WO3 in the Friedel-Crafts alkylation

Nb₂O₅ loaded on the supports and mixed with oxides was studied to investigate the activity and acidity for Friedel-Crafts benzylation of anisole. From the study on the loaded catalysts, a preliminary conclusion for the selection of metal oxide was obtained; namely, such an acidic oxide as silica was suitable for the support of Nb₂O₅. Then, MoO₃ and WO₃ were mixed with Nb₂O₅, and prominent high catalytic activity and acidities were observed. Both oxides of Nb₂O₅-MoO₃ and Nb₂O₅-WO₃ showed almost similar behavior with respect to characterization and catalytic activity. Surface area increased, X-ray diffraction (XRD) and Raman bands were lost, acid sites, both Brønsted and Lewis characters generated, and surface acid site density was as high as 2–4 nm⁻². The acid sites were generated on the amorphous metal oxides consisting of Nb and Mo or W oxides, different in nature from those of Nb₂O₅ calcined and un-calcined, and active for Friedel-Crafts benzylation.     

Preparation of niobates of rhodium and nickel and their catalytic behaviors during calcination and reduction treatments

Double oxides of Rh and Ni have been prepared by chemical mixing methods. Silica-supported and unsupported RhNbO₄ and NiNb₂O₆ catalysts exhibited strong metal-oxide interaction behaviors in ethane hydrogenolysis activities after the decomposition of the double oxides by H₂ reduction at 500°C. Silica-supported and zeolite-supported RhVO₄ catalysts showed high activity and selectivity for dehydrogenation of cyclohexane after the decomposition in H₂. The double-oxide catalyst systems can be used as starting materials to obtain high-performance metal catalysts (redispersion of metals by H₂ reduction and regeneration of catalysts by calcination at a high temperature).     

Ni-Mn/Al2O3催化剂在浆态床中CO甲烷化催化性能

采用共浸渍法制备了Ni-Mn/Al₂O₃催化剂,考察了助剂Mn的含量对催化剂结构及浆态床CO甲烷化性能的影响。采用XRD、H₂-TPR、BET、TEM、H₂-化学吸附等表征对催化剂进行了测试分析,结果表明,Mn助剂的引入能够促进Ni物种在载体表面的分散,减弱Ni物种与载体的相互作用,降低催化剂的还原温度,提高催化剂的比表面积,减小活性金属Ni的晶粒尺寸。随着Mn含量的增加,Ni-Mn/Al₂O₃催化剂的甲烷化性能先升后降,其中以Mn含量为4%（质量分数）时的催化甲烷化性能最佳,添加过量的Mn导致活性组分Ni被部分覆盖,催化甲烷化性能下降。通过对16Ni4Mn/Al₂O₃催化剂样品的浆态床反应温度及反应压力的研究发现,当反应温度为280℃、反应压力为1.5 MPa时,催化剂样品16Ni4Mn/Al₂O₃的CO转化率及CH₄选择性分别达到96.2%和88.8%。     

Preparation of highly dispersed niobium oxide on silica by equilibrium adsorption method

Two series of Nb₂O₅/SiO₂ catalysts are prepared by an equilibrium adsorption method (type A) and a conventional evaporation to dryness method (type E). The loading amounts of type A catalysts were low ( ˜ 0.2 wt% as Nb₂O₅) and those of type E catalysts were varied from 0.1 to 10 wt%. UV/VIS diffuse reflectance spectra of the catalyst samples show that micro particles of Nb₂O₅) are present on the catalysts with high-loading and monomeric or oligomeric niobate species are present on the catalysts with low-loading. By analyzing luminescence spectra of the low-loading samples, we conclude that the type A catalyst contains monomeric NbO₄ tetrahedra and the type E catalyst oligomeric NbO₄ tetrahedra. Propene photo-oxidation on type A catalysts yields propene oxide selectively, formed on monomeric NbO₄, whereas the photo-oxidation on the type E catalyst with low-loading yields propanal selectively. Propanal is the product in decomposition of propene oxide on oligomeric NbO₄ tetrahedra.     

氢气高温还原制备的负载型镍基催化剂用于苯酚加氢的性能

通过等体积浸渍法分别将Ni(NO₃)₂、NiCl₂、NiSO₄ 3种镍前体浸渍于A1₂O₃或SiO₂载体上,然后通过H₂高温还原法制备了负载型镍基催化剂,考察了镍前体、载体种类、镍负载量、反应条件等对镍基催化剂苯酚加氢性能的影响。结果表明,对比3种镍前体,在H₂高温还原体系中Ni(NO₃)₂最容易被还原,制备的镍基催化剂苯酚加氢活性最高。SiO₂负载的镍基催化剂活性远高于γ-Al₂O₃催化剂。适宜的Ni负载量有助于活性组分的分散和催化活性的提高。镍基催化剂的苯酚加氢产物以环己醇为主,相对缓和的反应条件更容易生成环己酮。在非极性溶剂正庚烷或环己烷存在下,苯酚加氢反应速率远远高于极性溶剂水或乙醇存在下的结果,而且环己酮的选择性更高。     

Density functional theory and kinetic Monte Carlo simulation study the strong metal–support interaction of dry reforming of methane reaction over Ni based catalysts

Oxide supports modify electronic structures of supported metal nanoparticles,and then affect the catalytic activity associated with the so-called strong metal-support interaction(SMSI).We herein report the strong influence of SMSI employing Ni_4/α-MoC(111) and defective Ni_4/MgO(100) catalysts used for dry reforming of methane(DRM,CO_2+CH_4→2 CO+2 H_2) by using density functional theory(DFT) and kinetic Monte Carlo simulation(KMC).The results show that α-MoC(111) and MgO(100) surface have converse electron and structural effect for Ni_4 cluster.The electrons transfer from a-MoC(111) surface to Ni atoms,but electrons transfer from Ni atoms to MgO(100) surface;an extensive tensile strain is greatly released in the Ni lattice by MgO,but the extensive tensile strain is introduced in the Ni lattice by α-MoC.As a result,although both catalysts show good stability,H_2/CO ratio on Ni_4/α-MoC(111) is obviously larger than that on Ni_4/MgO(100).The result shows that Ni/α-MoC is a good catalyst for DRM reaction comparing with Ni/MgO catalyst.     

Nb2O5 promoted Pd/AC catalyst for selective phenol hydrogenation to cyclohexanone

Phenol hydrogenation is a green route to prepare cyclohexanone, an intermediate for the production of nylon 66 and nylon 6. The development of high-performance catalysts still keeps a great challenge. Herein, the activated carbon (AC) was modified with an acidic material Nb₂O₅ to adjust the microstructure and surface properties of AC, and the influences of the calcination temperature and Nb₂O₅ content on the catalytic performance of the Pd/AC-Nb₂O₅ catalysts for the phenol hydrogenation to cyclohexanone were investigated. The Nb₂O₅ with proper content can be highly uniformly distributed on the AC surface, enhancing the acidity of the Pd/AC-Nb₂O₅ catalysts with comparable specific surface area and Pd dispersion, thereby improving the catalytic activity. The hybrid Pd/AC-10Nb₂O₅-500 catalyst exhibits the synergistic effect between the Pd nanoparticles and AC-10Nb₂O₅, which enhances the catalytic activity for the hydrogenation of phenol. Furthermore, the as-prepared Pd/AC-10Nb₂O₅-500 catalyst shows good reusability during 7 reaction cycles.     

铈锆固溶体CexZr1-xO2上H2S的选择性催化氧化性能

采用共沉淀法合成一系列具有不同Ce/Zr物质的量比的铈锆固溶体Ce_xZr_1-xO₂,考察Ce/Zr比例对H₂S选择氧化反应催化活性的影响。通过XRD、BET、Raman、XPS、CO₂-TPD、O₂-TPD、H₂-TPR等手段对铈锆固溶体的晶体结构、表面性质、碱性位以及氧化还原性等进行表征。结果表明,所有的铈锆固溶体催化剂均可以在化学计量比的氧气下具有优良的低温催化活性,催化活性随着Ce/Zr比例的提高而增加,其中Ce_0.9Zr_0.1O₂活性最高,(160~260) ℃转化率均保持在95%以上,在180 ℃时硫收率可达到97%,这主要是因为Ce_0.9Zr_0.1O₂具有最多的中度碱性位、活性位数量和强的氧化还原性。同时推测Ce⁴⁺为催化反应的活性位,并遵循氧化还原机理。此外,催化剂的失活主要是由于催化剂表面生成硫酸盐物种,消耗了活性组分Ce⁴⁺。     

Fe对Ni/SBA-16催化CO低温甲烷化促进作用的研究

为了提高Ni/SBA-16催化剂在低温下CO甲烷化中的活性,通过引入Fe助剂制备了Ni-Fe/SBA-16双金属催化剂。对催化剂进行XPS、XRD、HRTEM及EDS-mapping表征的结果表明,Fe的加入与Ni形成了Ni₃Fe合金,减小了金属颗粒尺寸,使得还原后金属颗粒平均粒径从60 nm降低到30 nm左右。同时H₂-TPR的结果表明,Ni₃Fe合金的形成增强了金属Ni与载体之间的相互作用,从而能够减弱Ni颗粒在还原过程及反应过程中的团聚。最后,由CO-TPD和H₂-TPD的测试结果可知,Ni₃Fe合金的形成促进了催化剂对反应气体CO和H₂的解离,从而提高了催化剂在低温下的CO甲烷化活性。当空速为150000 h^-1、压力为0.1 MPa、V(H₂)∶V(CO)∶V(N₂)=3∶1∶1时,CO最低完全转化温度可以从300°C降低到250°C,同时CH₄的选择性保持在90%。     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

微波热解制备g-Fe2O3催化剂及其SCR脱硝性能

以FeSO₄·7H₂O[Fe(NO₃)₃·9H₂O]为铁源,采用新型微波热解法制备γ-Fe₂O₃[a-Fe₂O₃]催化剂样品,通过XRD、N₂等温吸附-脱附、压汞法等实验手段对催化剂样品晶相、微观孔结构等进行表征;考察两种催化剂样品的NH₃-SCR脱硝性能,通过归一化处理得到两种催化剂在不同温度下的本征脱硝反应速率,同时对比研究了γ-Fe₂O₃与钒系催化剂的脱硝活性;研究氨氮比、氧浓度等运行参数对γ-Fe₂O₃催化剂NH₃-SCR脱硝性能的影响规律,并对其抗硫抗水性能进行考察.结果表明:采用新型微波热解法可得到纯度较高的γ-Fe₂O₃催化剂,其介孔分布合理且大孔数量丰富;同时γ-Fe₂O₃催化剂表现出优于a-Fe₂O₃催化剂的脱硝性能,400℃时最大NO_x转化率达到96%,300、325、350℃下单位面积脱硝速率达到a-Fe₂O₃催化剂的3倍左右;γ-Fe₂O₃催化剂具备优良的抗硫抗水性能,其最佳氨氮比为1、最佳氧体积分数为3.5%.     

用于燃烧前CO2捕集的微孔Nb2O5膜的制备及其水热稳定性能

以五正丁氧基铌为前驱体,通过溶胶-凝胶法制备出稳定的Nb₂O₅聚合溶胶,详细考察了溶胶制备过程参数(体系酸度、水解比、反应温度、反应时间和螯合剂用量)对溶胶尺寸、稳定性以及制备重复性的影响。采用平均粒径为4.8 nm的Nb₂O₅溶胶,通过浸浆法在平均孔径为3 nm的γ-Al₂O₃中孔膜上制备出Nb₂O₅微孔膜。利用TG、XRD、NH₃吸附-脱附、CO₂吸附、吡啶吸附傅里叶变换红外光谱(Py-IR)和单组分气体渗透实验等手段对Nb₂O₅粉体及微孔膜的性能进行了表征,结果表明:在200℃、0.3 MPa条件下,350℃烧成的微孔Nb₂O₅膜对H₂的渗透率和H₂/CO₂的理想分离因子分别为3.1×10^-9 mol·m^-2·s^-1·Pa^-1和21。此外,微孔Nb₂O₅膜经150 kPa的水蒸气处理8 h后,膜的渗透性能以及H₂/CO₂理想选择性基本保持不变。     

Au/LaCo_(1-x)Ce_xO_3催化剂的制备及其对CO催化氧化性能的研究

为进一步提高催化剂活性,用Ce对LaCoO3载体进行改性,并采用溶胶-凝胶法制备系列LaCo1-xCexO3(x=0~0.5)载体。其中,x=0.1和0.2时,载体为钙钛矿结构。采用沉积-沉淀法制备Au/LaCo1-xCexO3(x=0.1、0.2)催化剂,通过XRD、BET和H2-TPR等方法对催化剂进行催化活性评价及稳定性表征测试。结果表明,Au/LaCo0.9Ce0.1O3和Au/LaCo0.8Ce0.2O3催化剂能够在90℃将CO完全转化,在此温度进行的连续20h和30h的寿命实验中,CO转化率保持100%,催化活性和稳定性均优于Au/LaCoO3催化剂。表明掺杂Ce改性载体,能够提高催化剂活性和稳定性。