共查询到19条相似文献,搜索用时 171 毫秒
1.
2.
3.
涟钢20t转炉出钢过程钢液温降规律的研究 总被引:3,自引:1,他引:2
统计分析了涟钢20t氧气顶吹转炉的出钢温度、出钢过程钢水温降、出钢过程钢水温降速率等的分布状况,研究了影响出钢过程钢水温降的因素,建立了出钢过程钢水温度变化数学模型.研究结果表明,降低出钢温度、缩短出钢时间、提高钢包内衬温度可显著减少出钢过程钢水温降. 相似文献
4.
5.
涟钢20t转炉出钢过程钢流温降规律的研究 总被引:3,自引:0,他引:3
统计分析了涟钢20t氧气顶吹转炉的出钢温度,出钢过程钢水温降、出钢过程钢水温降速率等的分布状况,研究了影响出钢过程钢水温降的因素,建立了出钢过程钢水温度变化数学教学,研究结果表明,降低出钢温度,缩短出钢时间、提高钢包内衬温度可显著减少出钢过程钢水温降。 相似文献
6.
7.
8.
9.
10.
11.
为了研究包衬侵蚀对钢水温降的影响规律,通过ANSYS有限元软件以及ParaMesh网格随移技术建立了考虑包衬侵蚀的钢包传热计算模型,研究并分析了包衬侵蚀对包衬及钢水温度的影响规律。结果表明,包衬侵蚀对包衬温度影响较大,在相邻两个修包周期内,包衬侵蚀造成渣线和包壁的包衬内部(工作层与永久层交界处)温差为14~114 K;包衬侵蚀导致包壳外表面温度升高,包壳向外散热增加,与此同时,包衬受侵蚀变薄,蓄热减少,两者同时作用导致包衬侵蚀对钢水温降影响不大,最高不超过1 K,在实际生产中可以适当地忽略钢包侵蚀对钢水温降的影响。 相似文献
12.
13.
钢包吹氩引起的钢水温降分析 总被引:7,自引:0,他引:7
通过现场实验测试,认为钢包炉吹氩搅拌过程中,氩气升温吸热对钢液温降的影响极少,分析认为钢液产生较大温降主要原因是包衬蓄热和吹氩过程中形成的钢液裸露面对外散热,同时指出钢包内钢液温度的分层可减少通过包衬散热所带来的热损。 相似文献
14.
15.
为了确定合适的钢包烘烤预热温度,以某钢厂90t整体铝镁浇注料钢包为原型进行数值模拟,利用有限元分析软件ANSYS,采用间接耦合法进行计算,得出了不同烘烤预热温度工况下,钢包盛钢时的内衬温度变化及应力分布。结果表明:提高钢包预热温度可以降低钢包内衬的温升及钢液温降幅度,减小钢包内衬的温度梯度,减少内衬材料受热应力所引起的热震破坏,从而延长钢包使用寿命。综合考虑钢包内衬水分排除、节能及热应力分布等因素,钢包预热温度取1 173~1 273K最佳;钢包底部的烘烤预热温度应提高到1 373K。 相似文献
16.
17.
Transient, turbulent flow and heat transfer in a ladle during the holding period are numerically investigated. The ladle refractories
including the working lining, safety lining, insulation layer, and steel shell have been simultaneously taken into account.
No assumptions are made for the heat transfer between the liquid steel and the inside ladle walls. Both the initial ladle
heating and the heat loss from the slag surface are changed to examine their effect on thermal stratification in molten steel.
A simplified model for the heat loss from the molten steel to the refractory is proposed. Correlations for the history of
mean steel temperature, thermal stratification, and heat loss rate are obtained, which can be easily applied for industrial
operations. Predictions are compared with experimental data in an industrial ladle and a pilot plant ladle, and those from
previous studies. 相似文献
18.