Formation of high quality storage capacitor dielectrics by in-siturapid thermal reoxidation of Si3N4 films inN2O ambient

This letter reports on a novel reoxidation technique for SiO₂ /Si₃N₄ (ON) stacked films by using N₂ O as oxidant. Effect of in-situ rapid thermal N₂O reoxidation (RTNO) on the electrical characteristics of thin ON stacked films are studied and compared with those of in-situ rapid thermal. O ₂ reoxidation (RTO). Prior to reoxidation, the Si₃N₄ film was deposited by rapid thermal chemical vapor deposition (RT-CVD) using SiH₄ and NH₃. Results show that RTNO of the Si₃N₄ films significantly improves electrical characteristics of ON stacked films in terms of lower leakage current, suppressed charge trapping, reduced defect density and improved time-dependent-dielectric-breakdown (TDDB), as compared to RTO of the Si₃N₄ films     

Rapid thermal anneal of gate oxides for low thermal budget TFT's

The performance and reliability of deposited gate oxides for thin film transistors (TFT's) has been studied as a function of rapid thermal annealing (RTA) conditions. The effect of temperature ranging from 700 to 950°C and the annealing ambients including oxygen (O₂), argon (Ar), and nitrous oxide (N₂O) is investigated. Improvement in charge to breakdown (Q_bd) is seen starting from 700°C, with marked increase at 900°C temperature and above. The N₂O and Ar ambients result in higher Q_bd compared to O₂ ambient and we attribute this to reduced interfacial stress. Fourier Transform Infrared spectroscopy (FTIR) is used to qualitatively measure the stress. The bias temperature instability is decreased by RTA. The TFT characteristics are significantly improved with RTA gate oxide. The RTA-Ar anneal at 950°C results in the lowest trap density in TFT's as measured from charge pumping technique     

Uniform durable thin dielectrics prepared by rapid thermalprocessing in an N2O ambient

Thin dielectrics grown on silicon wafers by rapid thermal processing in an N₂O ambient at temperatures of 1100°C, 1150°C, and 1200°C are discussed. The resulting films, in conjunction with an O₂ ambient control were characterized by thickness measurements and electrical performance. Dielectrics formed in N₂O in this temperature range were all superior to that prepared in an O₂ ambient in terms of interface state generation and flatband voltage shift after constant current stressing. Although all N₂O prepared samples exhibited similar cross wafer electrical uniformity, higher growth temperatures favored thickness uniformity. The electrical behavior of the N₂O wafers was not strongly dependent on growth temperature; however, a 60-s 1100°C post-oxynitridation N₂ anneal was found to significantly reduce subsequent electrical performance. It is also demonstrated that under optimum process conditions, high-quality uniform dielectrics can be formed by RTP in N₂O     

Optimization of gate oxide N2O anneal for CMOSFET's atroom and cryogenic temperatures

This paper presents a study of the impact of gate-oxide N₂ O anneal on CMOSFET's characteristics, device reliability and inverter speed at 300 K and 85 K. Two oxide thicknesses (60 and 110 Å) and five N₂O anneal conditions (900~950°C, 5~40 min) plus nonnitrided process and channel lengths from 0.2 to 2 μm were studied to establish the correlation between the nitrogen concentration at Si/SiO₂ interface and the relative merits of the resultant devices. We concluded that one simple post-oxidation N₂O anneal step can increase CMOSFET's lifetime by 4~10 times, effectively suppress boron penetration from the P⁺ poly-Si gate of P-MOSFET's without sacrificing CMOS inverter speed. We also found that the benefits in terms of the improved interface hardness and charge trapping characteristic still exist at cryogenic temperature. All these improvements are found to be closely correlated to the nitrogen concentration incorporated at the Si/SiO₂ interface. The optimal N₂O anneal occurs somewhere at around 2% of nitrogen incorporation at Si/SiO₂ interface which can be realized by annealing 60~110 Å oxides at 950°C for 5 min or 900°C for 20 min     

Formation of high quality ultrathin oxide/nitride (ON) stackedcapacitors by in situ multiple rapid thermal processing [DRAMcells]

High quality, ultrathin (<30 Å) SiO₂/Si₃ N₄ (ON) stacked film capacitors have been fabricated by in situ rapid-thermal multiprocessing. Si₃N₄ film was deposited on the RTN-treated poly-Si by rapid-thermal chemical vapor deposition (RTCVD) using SiH₄ and NH₃, followed by in situ low pressure rapid-thermal reoxidation in N₂O (LRTNO) or in O₂ (LRTO) ambient. While the use of low pressure reoxidation suppresses severe oxidation of ultrathin Si₃N₄ film, the use of N₂O-reoxidation significantly improves the quality of ON stacked film, resulting in ultrathin ON stacked film capacitors with excellent electrical properties and reliability     

Novel capacitor process using diffusion barrier rounded by Si3N4 spacer for high density FRAM device

A novel capacitor process was successfully implemented in 4 Mb FRAM device by developing a barrier layer rounded by Si₃N₄ spacer (BRS) scheme. Using this process, it is possible to eliminate an undesired barrier etching damage, which is a major role in degrading ferroelectric properties. The novel capacitor process was generated by etching an Ir barrier layer and rounding the barrier by a Si₃N₄ spacer before preparing Pb(Zr _1-xTi_x)O₃ (PZT) films. It was observed that uniform sol-gel derived PZT films were prepared on the patterned Ir substrate by using Si₃N₄ spacer, which provides a smooth edge of the patterned cell. The contact resistance between bottom electrode and polysilicon plug after full integration was monitored below 700 Ω per contact with contact size 0.6×0.6 (μm²). Compared to the ferroelectric capacitor damaged by barrier etching, the novel Pb(Zr_1-xTi_x)O₃ (PZT) capacitor exhibited a well-saturated Q-V curve. The fully processed novel capacitor having 1.2×1.2 (μm²) effective area displayed remnant polarization of 14 (μC/cm²) at an operating voltage of 3.0 V. The BRS ferroelectric capacitor showed a reliable retention property until 100 h at 125°C. Same state retention (Qss) was stable with time up to 100 h while opposite state retention (Qos) showed a log-linear decay rate at 125°C thermal stress     

High quality gate dielectrics grown by rapid thermal processingusing split-N2O technique onstrained-Si0.91Ge0.09 films

Thermal stability and strain relaxation temperature of strained Si _0.91Ge_0.09 layers has been investigated using double crystal x-ray diffraction (DCXRD). High quality gate oxynitride layers rapid thermally grown on strained Si_0.91Ge_0.09 using N₂O and the split N₂O cycle technique below the strained relaxed temperature is reported. A positive fixed oxide charge density was observed for N₂O and split-N₂ O grown films. The O₂ grown films exhibit a negative fixed oxide charge. The excellent improvements in the leakage current, breakdown field and charge-to-breakdown value of the N₂O or split-N₂O grown films were achieved compared to pure O₂ grown films     

Reduction of RIE-damage by N2O-anneal of thermal gateoxide

We have investigated RIE-induced damage in MOS devices with thermal oxide as well as N₂O-annealed oxide as gate dielectrics. A systematic improvement in robustness against RIE-induced damage is seen when N₂O flow rate and/or N₂O anneal temperature are increased. We have demonstrated a N₂O anneal process at 900°C, which provides a robust SiO₂/Si interface against plasma damage and hot carrier stress     

Promising storage capacitor structures with thin Ta2O5 film for low-power high-density DRAMs

To ensure the required capacitance for low-power DRAMs (dynamic RAMs) beyond 4 Mb, three kinds of capacitor structures are proposed: (a) poly-Si/SiO₂/Ta₂O₅/SiO₂ /poly-Si or poly-Si/Si₃N₄/Ta₂O ₅/SiO₂/poly-Si (SIS), (b) W/Ta₂O₅ /SiO₂/poly-Si (MIS), and (c) W/Ta₂O₅ W (MIM). The investigation of time-dependent dielectric breakdown and leakage current characteristics indicates that capacitor dielectrics that have equivalent SiO₂ thicknesses of 5, 4, and 3 nm can be applied to 3.3-V operated 16-Mb DRAMs having stacked capacitor cells (STCs) by using SIS, MIS, and MIM structures, respectively, and that 3 and 1.5 nm can be applied to 1.5-V operated 64-Mb DRAMs having STCs by using MIS and MIM structures, respectively. This can be accomplished while maintaining a low enough leakage current for favorable refresh characteristics. In addition, all these capacitors show good heat endurance at 950°C for 30 min. Therefore, these capacitors allow the fabrication of low-power high-density DRAMs beyond 4 Mb using conventional fabrication processes at temperatures up to 950°C. Use of the SIS structure confirms the compatability of the fabrication process of a storage capacitor using Ta₂O₅ film and the conventional DRAM fabrication processes by successful application to the fabrication process of an experimental memory array with 1.5-μm×3.6-μm stacked-capacitor DRAM cells     

Oxidized Ta2O5/Si3N4dielectric films on poly-crystalline Si for dRAMs

A dielectric film technology characterized by a novel multilayer structure formed by oxidation of Ta₂O₅/Si₃ N₄ films on polysilicon has been developed to realize high-density dRAMs. The dry oxidation of the Ta₂O₅/Si₃N₄ layers was performed at temperatures higher than 900°C. This film has a capacitance per unit area from 5.5 to 6.0 fF/ μm², which is equivalent to that of a 6.0- to 6.5-nm-thick SiO₂. The leakage current at an effective electric field of 5 MV/cm is less than 10^-9 A/cm². Under such an electric field, the extrapolated time to failure for 50% cumulative failure can be as high as 1000 years     

Effects of surface pretreatment of polysilicon electrode prior toSi3N4 deposition on the electrical characteristicsof Si3N4 dielectric films

Effects of various surface pretreatments of polysilicon electrode prior to Si₃N₄ deposition on leakage current, time-dependent dielectric breakdown (TDDB) and charge trapping characteristics of thin Si₃N₄ films deposited on rugged and smooth poly-Si are investigated. Surface pretreatments consist of different combinations of HF clean, rapid thermal H₂ -Ar clean, and rapid thermal NH₃-nitridation (RTN) and are intended to modify the surface of bottom poly-Si electrode. Results show that RTN treatments lead to lower leakage current, reduced charge trapping, and superior TDDB characteristics as compared to rapid thermal H₂-Ar clean     

Enhanced H2-plasma effects on polysilicon thin-filmtransistors with thin ONO gate-dielectrics

This letter reports that passivation effects of the H₂-plasma on the polysilicon thin-film transistors (TFT's) were greatly enhanced if the TFT's have a thin Si₃N₄ film on their gate-dielectrics. Compared to the conventional devices with only the SiO₂ gate dielectric, the TFT's with Si ₃N₄ have much more improvement on their subthreshold swing and field-effect mobility after H₂-plasma treatment     

Atmospheric pressure ionization mass spectroscopy for the study ofpermeation in polymeric tubing

An atmospheric pressure ionization mass spectrometer (APIMS) is used to determine the permeation coefficients for two widely used kinds of polymeric tubing, PF and Kel-F (PCTFE), at 25°C and 75°C. In the experiments, an ultra-high-purity N₂ gas flow was maintained through the test tubing. The net impurity uptake by nitrogen due to the permeation of O₂, CO₂, H₂O, and CH₄ from surrounding air into the polymeric tubing was measured by APIMS with sub-ppb sensitivities. CH₄ had the highest and O₂ had the lowest permeation coefficients. Results show that Kel-F was a superior barrier material for all impurities studied. The permeation coefficients for these polymers increased with temperature but did not change significantly with the permeant partial pressure. The permeability of PFA showed a stronger temperature dependence than that of Kel-F     

Study of etch rate characteristics of SF6/He plasmas byresponse-surface methodology: effects of interelectrode spacing

The characteristics of SF₆/He plasmas which are used to etch Si₃N₄ have been examined with experimental design and modeled empirically by response-surface methodology using a Lam Research Autoetch 480 single-wafer system. The effects of variations of process gas flow rate (20-380 sccm), reactor pressure (300-900 mtorr). RF power (50-450 W at 13.56 MHz), and interelectrode spacing (8-25 mm) on the etch rates of LPCVD (low-pressure chemical vapor deposition) Si₃N₄, thermal SiO₂, and photoresist were examined at 22±2°C. Whereas the etch rate of photoresist increases with interelectrode spacing between 8 and 19 mm and then declines between 19 and 25 mm, the etch rate of Si₃N ₄ increases smoothly from 8 to 25 mm, while the etch rate of thermal SiO₂ shows no dependence on spacing between 8 and 25 mm. The etch rates of all three films decrease with increasing reactor pressure. Contour plots of the response surfaces for etch rate and etch uniformity of Si₃N₄ as a function of spacing and flow rate at constant RF power (250 W) display complex behavior at fixed reactor pressures. A satisfactory balance of etch rate and etch uniformity for Si₃N₄ is predicted at low reactor pressure (~300 mtorr), large electrode spacing (12-25 mm), and moderate process gas flow rates (20-250 sccm)     

Studies of CW lasing action in CO2-CO,N2O-CO, CO2-H2O, and N2O-H2O mixtures pumped by blackbody radiation

A proof of principle experiment to evaluate the efficacy of CO and H₂O in increasing the power output for N₂O and CO ₂ lasing mixtures has been conducted and theoretically analyzed for a blackbody radiation-pumped laser. The results for N₂ O-CO, CO₂-CO, N₂O-H₂O and CO₂-H₂O mixtures are presented. Additions of CO to the N₂O lasant increased power up to 28% for N₂O laser mixtures, whereas additions of CO to the CO₂ lasant, and the addition of H₂O to both the CO₂ and N₂O lasants, resulted in decreased output power     

Characterization of ultrathin oxynitride (18-21 A) gate dielectricsby NH3 nitridation and N2O RTA treatment

In this paper, we developed a new method to grow robust ultrathin oxynitride (E_OT=18 A) film with effective dielectric constant of 7.15. By NH₃-nitridation of Si substrate, grown ultrathin Si₃N₄ With N₂O annealing shows excellent electrical properties in terms of significant lower leakage current, very low bulk trap density and trap generation rate, and high endurance in stressing. In addition, this oxynitride film exhibits relatively weak temperature dependence due to a Fowler-Nordheim (FN) tunneling mechanism. This dielectric film appears to be promising for future ultralarge scale integrated (ULSI) devices     

InGaN/GaN light emitting diodes activated in O2 ambient

Mg-doped GaN epitaxial layers were annealed in pure O₂ and pure N₂. It was found that we could achieve a low-resistive p-type GaN by pure O₂ annealing at a temperature as low as 400°C. With a 500°C annealing temperature, it was found that the forward voltage and dynamic resistance of the InGaN/GaN light emitting diode (LED) annealed in pure O₂ were both smaller than those values observed from InGaN/GaN LED annealed in pure N₂. It was also found that an incomplete activation of Mg will result in a shorter LED lifetime     

The degradation of TDDB characteristics of Si02/Si3N4/Si02 stacked films caused by surfaceroughness of Si3N4 films [DRAMs]

The effect of surface roughness of Si₃N₄ films on time-dependent dielectric breakdown (TDDB) characteristics of SiO₂/Si₃N₄/SiO₂ (ONO) stacked films was investigated. The surface roughness of Si₃N ₄ films-was found to become higher with increasing deposition temperature and to cause the degradation of TDDB characteristics of ONO films in DRAMs. A local thinning of ONO films, evaluated from the TDDB characteristics, agreed with the surface roughness measured by atomic force microscopy (AFM) and cross-sectional transmission electron microscopy (XTEM). Dependence of time to breakdown of ONO films on the deposition conditions was interpreted by electric field intensification due to the surface roughness of Si₃N₄ films     

Reduction of oxide charge and interface-trap density in MOScapacitors with ITO gates

The electrical properties of MOS capacitors with an indium tin oxide (ITO) gate are studied in terms of the number density of the fixed oxide charge and of the interface traps N_f and N _it, respectively. Both depend on the deposition conditions of ITO and the subsequent annealing procedures. The fixed oxide charge and the interface-trap density are minimized by depositing at a substrate temperature of 240°C at low power conditions and in an oxygen-rich ambient. Under these conditions, as-deposited ITO films are electrically conductive. The most effective annealing procedure consists of a two-step anneal: a 45-s rapid thermal anneal at 950°C in N₂, followed by a 30 min anneal in N₂/20% H₂ at 450°C. Typical values obtained for N_it and N_f are 4.2×10¹⁰ cm^-2 and 2.8×10¹⁰ cm^-2, respectively. These values are further reduced to 1.9×10¹⁰ cm^-2 and ≲5×10⁹ cm^-2, respectively, by depositing approximately 25 nm polycrystalline silicon on the gate insulation prior to the deposition of ITO     

High efficiency polycrystalline silicon solar cells using lowtemperature PECVD process

Conventionally directionally solidified (DS) and silicon film (SF) polycrystalline silicon solar cells are fabricated using gettering and low temperature plasma enhanced chemical vapor deposition (PECVD) passivation. Thin layer (~10 nm) of PECVD SiO₂ is used to passivate the emitter of the solar cell, while direct hydrogen rf plasma and PECVD silicon nitride (Si₃N₄) are implemented to provide emitter and bulk passivation. It is found in this work that hydrogen rf plasma can significantly improve the solar cell blue and long wavelength responses when it is performed through a thin layer of PECVD Si₃N₄. High efficiency DS and SF polycrystalline silicon solar cells have been achieved using a simple solar cell process with uniform emitter, Al/POCl₃ gettering, hydrogen rf plasma/PECVD Si₃N₄ and PECVD SiO₂ passivation. On the other hand, a comprehensive experimental study of the characteristics of the PECVD Si₃N₄ layer and its role in improving the efficiency of polycrystalline silicon solar cells is carried out in this paper. For the polycrystalline silicon used in this investigation, it is found that the PECVD Si₃N₄ layer doesn't provide a sufficient cap for the out diffusion of hydrogen at temperatures higher than 500°C. Low temperature (⩽400°C) annealing of the PECVD Si₃N ₄ provides efficient hydrogen bulk passivation, while higher temperature annealing relaxes the deposition induced stress and improves mainly the short wavelength (blue) response of the solar cells