Improving the Na2SO4-induced corrosion resistance of Ti3AlC2 by pre-oxidation in air

Ti₃AlC₂ suffers severe Na₂SO₄-induced corrosion attacks at temperatures higher than 800 °C in air. A convenient and efficient pre-oxidation method is proposed to enhance the corrosion resistance of Ti₃AlC₂. The corrosion weight-changes of the pre-oxidized samples were decreased by about four orders of magnitude compared with those of the untreated specimens. The mechanism on improvement of corrosion resistance was investigated by means of thermogravimetric analysis, X-ray diffraction and scanning electron microscopy/energy-dispersive spectroscopy. A continuous and adherent α-Al₂O₃ scale was prepared by high-temperature pre-oxidation treatment in air. The preformed dense Al₂O₃ scale has good compatibility with the Ti₃AlC₂ substrate, and consequently, can act as an efficient barrier against corrosion. Long-time corrosion tests demonstrate that the Al₂O₃ scale conserves after corrosion attack and is capable of long-term stability.     

Hot corrosion of Ti3SiC2-based ceramics coated with Na2SO4 at 900 and 1000 °C in air

The hot corrosion behavior of polycrystalline Ti₃SiC₂ under thin films of Na₂SO₄ was studied at 900 and 1000 °C in air. The microstructure and composition of the scales were investigated by scanning electron microscope/energy dispersive spectroscope and X-ray diffraction. The results demonstrated that Ti₃SiC₂ suffered from serious attack during hot corrosion at 900 and 1000 °C. The corroded scale had a duplex microstructure, the outer layer consisted of coarse grains with pores, the inner layer consisted of fine grains and was compact. The whole corroded layer consisted of a mixture of TiO₂ and SiO₂ after hot corrosion attack, which was different from the scale formed during the oxidation of Ti₃SiC₂ in air.     

Hot corrosion behaviour of plasma sprayed YSZ/Al2O3 dispersed NiCrAlY coatings on Inconel-718 superalloy

Oxide dispersed NiCrAlY bond coatings have been developed for enhancing thermal life cycles of thermal barrier coatings (TBCs). However, the role of dispersed oxides on high temperature corrosion, in particular hot corrosion, has not been sufficiently studied. Therefore, the present study aims to improve the understanding of the effect of YSZ dispersion on the hot corrosion behaviour of NiCrAlY bond coat. For this, NiCrAlY, NiCrAlY + 25 wt.% YSZ, NiCrAlY + 50 wt.% YSZ and NiCrAlY + 75 wt.% YSZ were deposited onto Inconel-718 using the air plasma spraying (APS) process. Hot corrosion studies were conducted at 800 °C on these coatings after covering them with a 1:1 weight ratio of Na₂SO₄ and V₂O₅ salt film. Hot corrosion kinetics were determined by measuring the weight gain of the specimens at regular intervals for a duration of 51 h. X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy techniques were used to determine the nature of phases formed, examine the surface attack and to carry out microanalysis of the hot corroded coatings respectively. The results show that YSZ dispersion causes enhanced hot corrosion of the NiCrAlY coating. Leaching of yttria leads not only to the formation of the YVO₄ phase but also the destabilization of the YSZ by hot corrosion. For the sake of comparison, the hot corrosion behaviour of a NiCrAlY + 25 wt.% Al₂O₃ coating was also examined. The study shows that the alumina dispersed NiCrAlY bond coat offers better hot corrosion resistance than the YSZ dispersed NiCrAlY bond coat, although it is also inferior compared to the plain NiCrAlY bond coat.     

Synthesis of Ti3SiC2 bulks by infiltration method

T₃SiC₂ bulks have been synthesized by infiltrating Si liquid into porous precursor pellets composed of solid TiC and Ti powders. Silicon pellets were placed at the bottom of the precursor pellets as the liquid source. The starting compositions can be represented by the formula 2TiC + Ti + xSi, where x = 1.0, 1.2, 1.5 and 1.8, respectively. The phase formation and microstructure of the bulks were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy-dispersive spectroscopy (EDS) system. The results demonstrated that the TiC/Ti precursor pellet could only react with Si completely when the x value is 1.8. Impurities SiC, Ti-Si binary compounds and Ti₈C₅ appeared along the silicon diffusion direction. It is found that the compositions of impurities strongly depended on the Si-concentration. Reaction mechanism of this Ti₃SiC₂ infiltration synthesis has also been discussed based on the Si-concentration changes on the diffusion path.     

Low-temperature fabrication of high purity Ti3SiC2

In this study, we fabricated high purity Ti₃SiC₂ ceramic by mechanical alloying (MA) and spark plasma sintering (SPS), and investigated the effect of trace amount of Al on these processes. Our results show that addition of proper amount of Al significantly increases the purity of Ti₃SiC₂ in the MA and subsequent SPS products, and remarkably reduces the sintering temperature for Ti₃SiC₂. Ti₃SiC₂ sintered compact with a purity of 96.5 wt% was obtained by 10 h of MA and subsequent SPS from a starting mixture composed of n(Ti):n(Si):n(Al):n(c) = 3:1:0.2:2 at 850 °C. At 1100 °C, Ti₃SiC₂ with a purity of 99.3 wt% and a relative density of 98.9% was obtained.     

Synthesis of Ti3SiC2 by infiltration of molten Si

High-purity Ti₃SiC₂ compounds have been fabricated by infiltration of molten Si into a precursor, a partially sintered TiC_x (x = 0.67) preform. The Si source and the TiC_x preform were placed side by side on carbon cloth, and the system was heated to 1550 °C. Molten Si infiltrated the preform through the carbon cloth, and a direct reaction between TiC_x and molten Si immediately occurred at the reaction temperature to yield pure Ti₃SiC₂. We could observe phase formation and the microstructure of the bulk products with time, which were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy-dispersive spectroscopy (EDS). Pure Ti₃SiC₂ compounds were formed on the exterior of the TiC_x preform at 1550 °C when the sintered TiC_x:Si ingot molar ratio was 3:1.4. At 1550 °C, no other minor phases were detected for any of the sintering time ranges.     

Na2SO4- and NaCl-Induced hot corrosion of six nickel-base superalloys

The short-time hot-corrosion behavior of six industrial nickel-base superalloys was investigated with static deposits of Na₂SO₄ or NaCl or both in still air. The oxidation kinetics and scale morphologies were measured with traditional laboratory techniques-thermobalance, metallography, electron microprobe, and x-ray analyses. Susceptibility to hot corrosion was found to be correlated to the type of scale produced during simple oxidation. Alloys forming an A1₂O₃ scale were found to be susceptible to Na₂SO₄ deposits, independent of their chromium content. The quantity of Na₂SO₄ deposit dictated the nature of the attack and, under certain conditions, the refractory element alloy additions appeared to play an essential role. Alloys containing Cr₂O₃ or TiO₂ in the simple oxidation scale proved to be sensitive to NaCl attack. Again, the severity of the attack within the susceptible alloy group was not related to the chromium or titanium content. Although less intensive than the Na₂SO₄ -induced hot corrosion, NaCl contaminations provoked extensive spalling. All of the hotcorrosion types encountered in this study were interpreted in the light of existing theories.Supported by the Délégation Générale à la Recherche Scientifique et Technique.     

The effect of K2SO4 additive in Na2SO4 deposits on low temperature hot corrosion of iron-aluminum alloys

To understand the effect of K₂SO₄ additive in an Na₂SO₄ deposit on low temperature hot corrosion, the corrosion behavior of Fe-Al alloys induced by Na₂SO₄+K₂SO₄ was compared to that by Na₂SO₄ alone, and sulfation of Fe₂O₃ in the presence of either Na₂SO₄ or Na₂SO₄+K₂SO₄ was studied. It was found that K₂SO₄ additive promoted the low temperature hot corrosion, but did not change the corrosion-mechanism. Experimental results refuted the prior suggestions that the accelerated hot corrosion resulted either from the formation of K₃Fe(SO₄)₃ or from the stimulation of sulfation of Fe₃O₃. The earlier formation of the eutectic melt caused the accelerated hot corrosion, or in other words, the K₂SO₄ additive shortened the induction stage of hot corrosion.     

Ni/Cu定向结构涂层在不同浓度H2SO4中的耐蚀性能

为了研究Cu元素对Ni基合金定向结构涂层耐腐蚀性能的影响,向Ni60合金粉末中添加了5%Cu(质量分数,下同),制备了定向结构Ni60/Cu复合涂层。采用电化学试验和浸泡试验,评估了涂层在不同浓度H₂SO₄溶液中的电化学腐蚀特性和浸泡腐蚀性能,探讨了涂层在不同浓度H₂SO₄溶液中的腐蚀行为。结果表明,涂层在不同浓度H₂SO₄溶液中的腐蚀均表现为活化-钝化-过钝化的过程,电化学阻抗谱在整个时间常数内具有典型的容抗特征,H₂SO₄溶液浓度从5%增至80%时,电荷转移电阻先减小后增大,涂层的耐腐蚀性呈现先降低后升高的趋势。随着H₂SO₄溶液浓度的增加,涂层表面的腐蚀程度先加剧后逐渐减缓,且在H₂SO₄溶液浓度为40%时,腐蚀电位移至最负,腐蚀电流密度增至最大。但在H₂SO₄溶液浓度达到80...     

Rapid fabrication of the Ti3SiC2 bonded diamond composite by spark plasma sintering

A mixture of Ti/Si/TiC/diamond powders was employed to fabricate the Ti₃SiC₂ bonded diamond composite using the spark plasma sintering-reactive synthesis method. The addition of diamond does not inhibit the synthesis of Ti₃SiC₂ in the sintered product. In the matrix Ti₃SiC₂ grains developed lamellar morphology with an average length size of 5-10 μm. Ti₃SiC₂ matrix displays good pullout strength with diamond, and the Ti₃SiC₂ bonded diamond material exhibits good wear resistance.     

钼酸钠常温磷化液的研究

    选择钼酸钠作为磷化液的主促进剂.对其所得磷化膜的耐蚀性和膜重做了检测;用扫描电子显微镜对磷化膜的微观结构进行分析;同时研究了磷化时间和磷化温度对磷化膜性能的影响.     

Improving the surface hardness and wear resistance of Ti3SiC2 by boronizing treatment

In order to modify surface properties of Ti₃SiC₂, boronizing was carried out through powder pack cementation in the 1100-1400 °C temperature range. After boronizing treatment, one mixture layer, composed of TiB₂ and β-SiC, forms on the surface of Ti₃SiC₂. The growth of the coating is processed by inward diffusion of boron and obeys a linear rule. The boronizing increases the hardness of Ti₃SiC₂ from 3.7 GPa to a maximal 9.3 GPa and also significantly improves its wear resistance.     

Effect of Na2SO4 and Water Vapor on the Corrosion of Ti3SiC2

The corrosion behavior of polycrystalline Ti₃SiC₂ was studied in the presence of Na₂SO₄ deposit and water vapor at 900°C and 1000°C. The mass gain per unit area of the samples superficially coated with Na₂SO₄ exposed to water vapor was slightly lower than that of the samples corroded without water vapor. The microstructure and composition of the scales were investigated by SEM/EDS and XRD. Pores were observed in the corroded sample surfaces. The main corrosion phases on the sample surface were identified by XRD as TiO₂, Na₂Si₂O₅ and Na₂TiO₃. After Ti₃SiC₂ corroded in the presence of the Na₂SO₄ deposit and water vapor, the scale had a three-layer microstructure, which was different from the duplex corrosion scale formed on Ti₃SiC₂ beneath the Na₂SO₄ film without water vapor. Because water vapor penetrated the corrosion layer and then reacted with SiO₂ to form volatile Si(OH)₄, an intermediate porous and TiO₂-enriched layer formed in the corrosion layer.     

Hot corrosion behavior of detonation gun sprayed Cr3C2–NiCr coatings on Ni and Fe-based superalloys in Na2SO4–60% V2O5 environment at 900 °C

The present work investigates the hot corrosion resistance of detonation gun sprayed (D-gun) Cr₃C₂–NiCr coatings on Superni 75, Superni 718 and Superfer 800 H superalloys. The deposited coatings on these superalloy substrates exhibit nearly uniform, adherent and dense microstructure with porosity less than 0.8%. Thermogravimetry technique is used to study the high temperature hot corrosion behavior of bare and Cr₃C₂–NiCr coated superalloys in molten salt environment (Na₂SO₄–60% V₂O₅) at high temperature 900 °C for 100 cycles. The corrosion products of the detonation gun sprayed Cr₃C₂–NiCr coatings on superalloys are analyzed by using XRD, SEM, and FE-SEM/EDAX to reveal their microstructural and compositional features for elucidating the corrosion mechanisms. It is shown that the Cr₃C₂–NiCr coatings on Ni- and Fe-based superalloy substrates are found to be very effective in decreasing the corrosion rate in the given molten salt environment at 900 °C. Particularly, the coating deposited on Superfer 800 H showed a better hot corrosion protection as compared to Superni 75 and Superni 718. The coatings serve as an effective diffusion barrier to preclude the diffusion of oxygen from the environment into the substrate superalloys. It is concluded that the hot corrosion resistance of the D-gun sprayed Cr₃C₂–NiCr coating is due to the formation of desirable microstructural features such as very low porosity, uniform fine grains, and the flat splat structures in the coating.     

Thermodynamics of the Na2SO4-K2SO4-CoSO4 system and their relevance to low-temperature hot corrosion

Thermodynamic calculations and experiments were performed to determine the SO₃ partial pressures and temperatures at which K₂SO₄-CoSO₄ binary mixed liquid phases form on CoO and Co₃O₄ in the presence of K₂SO₄. The calculations and experiments are in excellent agreement. Similar calculations were also made of the compositions at the liquidus surface and the associated SO₃ partial pressures for the K₂SO₄-Na₂SO₄-CoSO₄ ternary system. These calculations show that the presence of K₂SO₄ substantially reduces the SO₃ partial pressures required to stabilize a liquid salt phase on the surface of oxidized cobalt alloys at 600–800°C. Consequently, at these temperatures the hot corrosion in coal-fired systems, where K levels are high, is expected to be worse than in oil-fired systems, where K levels are low. This prediction was confirmed by experiments in a pressurized fluidized bed coal combustor and in an atmospheric pressure burner rig.     

Power factor enhancement in Zn-doped Na0.8CoO2

The thermoelectric properties of Na_0.8Zn_xCo_1−xO₂/(ZnO)_y (x ≤ 0.01, 0 ≤ y ≤ 0.14) have been systematically investigated. The results suggest that doping divalent Zn ions within solubility limit x^* ∼ 0.01 leads to simultaneous reduction in resistivity and enhancement of thermopower. Analysis of the results show that the reduction of resistivity may be attributed to improved mobility of carriers, while the enhancement of thermopower may originate from the geometric relaxation of distorted CoO₆ octahedra caused by partial Zn substitution, leading to a narrower band width in the strongly correlated environment, consequently resulting in a remarkable 20% improvement in power factor.     

Corrosion behavior of select MAX phases in NaOH, HCl and H2SO4

In this paper we report on the electrochemical corrosion of select MAX phases, namely Ti₂AlC, (Ti,Nb)₂AlC, V₂AlC, V₂GeC, Cr₂AlC, Ti₂AlN, Ti₄AlN₃, Ti₃SiC₂ and Ti₃GeC₂ in 1 M NaOH, 1 M HCl and 1 M H₂SO₄ solutions. Polarization characteristics recorded in 1 M NaOH show that V₂AlC, V₂GeC and Cr₂AlC undergo active dissolution at potentials more positive than the corrosion potential, while Ti₂AlC, (Ti,Nb)₂AlC, Ti₃SiC₂ and Ti₃GeC₂ passivate. In the 1 M HCl solutions, Ti₂AlC, V₂AlC and V₂GeC actively dissolve; Ti₃SiC₂ and Ti₃GeC₂ passivate. Depending on potential, (Ti,Nb)₂AlC and Cr₂AlC showed trans-passive behavior. In 1 M H₂SO₄ solutions, Ti₂AlC, (Ti,Nb)₂AlC, Ti₃SiC₂ and Ti₃GeC₂ passivate, V₂AlC and V₂GeC show active dissolution, while Cr₂AlC exhibits trans-passive behavior. Ti₂AlN and Ti₄AlN₃ were passive in all solutions except in 1 M HCl, where Ti₂AlN showed trans-passive behavior. Given that the corrosion behavior of (Ti,Nb)₂AlC is unlike either Ti or Nb, the behavior of the former cannot be predicted from that of the latter.     

低品位钒渣在碳酸钠存在下的氧化过程

利用XRD,SEM/EDS和TG-DSC等手段对低品位钒渣在Na2CO3存在条件下的氧化过程进行检测。结果表明：钒渣的氧化温度范围为273至700°C,橄榄石相与尖晶石相彻底分解的温度分别是500和600°C,大部分水溶性的钒酸盐在500与600°C之间形成。当温度达到700°C以上时,钒酸盐富集相明显可见,但焙烧温度在800°C以上时,样品发生烧结,并且钒被形成的玻璃相包裹,导致其浸出率下降。同时,研究不同焙烧温度对钒浸出率的影响,并对浸出残渣进行分析。     

Accelerated oxidation of iron induced by Na2SO4 deposits in oxygen at 750°C—A new type low-temperature hot corrosion

Na ₂ SO ₄ -induced accelerated corrosion of iron in oxygen at 750°C was observed. EDX, XRD, SEM, EPMA and some chemical examinations were carried out to understand the corrosion mechanism. The accelerated oxidation was attributed to the formation of abundant sulfide which has a highly defected lattice and allows rapid diffusion of iron ions. The sulfide resulted in turn from the formation of a liquid phase which was a eutectic melt of Na ₂ SO ₄ and Na ₂ O. The formation of and other possible effects of the melt were discussed. The accelerated oxidation was compared with the usual low-temperature hot corrosion, showing that it has most of the characteristics of low-temperature hot corrosion except that it occurred under basic conditions developed by the removal of sulfur from the sulfate deposits instead of the usual acidic conditions established by the SO ₃ in the atmosphere.     

Na2SiF6活性激光焊接TC4钛合金焊缝成形和组织

采用Na₂SiF₆作为表面活性剂激光焊接TC4钛合金,通过观察焊缝表面,确定了Na₂SiF₆对TC4钛合金激光焊焊缝表面成形的影响;采用高速摄像技术,观察分析了焊件上方高温光致等离子体形态特征变化;借助光学显微镜观察分析了焊缝熔深和熔宽的变化及微观组织. 结果表明,涂覆Na₂SiF₆活性剂后TC4钛合金激光焊焊缝表面成形良好,可使焊缝熔深增加约0.8% ~ 12%,焊缝表面熔宽降低约10% ~ 29%,能够有效提高焊缝的深宽比;Na₂SiF₆活性剂改善了焊缝微观组织的不均匀性,改变了焊缝上部β柱状晶的结晶方向,细化了焊缝的晶粒尺寸和微观组织.