Influence of $$\hbox {TiO}_{2}$$ particle size and conductivity of the CuCrO$$_{2}$$2 nanoparticles on the performance of solid-state dye-sensitized solar cells

Solid-state dye-sensitized solar cells have been fabricated with mesoporous \(\hbox {TiO}_{2 }\) photoanode and N719 dye as photosensitizer. First, \(\hbox {TiO}_{2}\) and non-doped, Zn- and Mg-doped CuCrO\(_{2}\) nanoparticles have been synthesized by sol–gel method. In addition, the \(\hbox {TiO}_{2}\) pastes have been prepared through Pechini-type sol–gel method. The effect of \(\hbox {TiO}_{2}\) particle size, mesoporous \(\hbox {TiO}_{2}\) photoanode thickness and solid-state electrolyte thickness on the efficiency of the fabricated devices has been investigated. Our results show that in spite of the low amount of dye loading for photoanode with large \(\hbox {TiO}_{2}\) nanoparticles (80–180 nm), the dye-sensitized solar cell made from it has higher efficiency than that constructed from the photoanode comprising of small particles about 10–15 nm in size. The higher efficiency is attributed to the longer diffusion length of electrons because of a better electron transport and penetration of a large amount of \(\hbox {CuCrO}_{2 }\) nanoparticles in the porous structure of \(\hbox {TiO}_{2}\) photoanode. By using the doped \(\hbox {CuCrO}_{2}\) nanoparticles, the efficiency has been increased from 0.027% for \(\hbox {TiO}_{2}\)/N719 dye/CuCrO\(_{2}\) to 0.033% for \(\hbox {TiO}_{2}\)/N719 dye/CuCrO\(_{2}\):Zn and further increased to 0.042% for \(\hbox {TiO}_{2}\)/N719 dye/CuCrO\(_{2}\):Mg. The efficiency enhancement by doping is ascribed to the conductivity improvement due to the presence of impurity atoms.     

A first-principle investigation into effect of B- and BN-doped $$\hbox {C}_{60}$$ in lowering dehydrogenation of $$\hbox {MXH}_{4}$$MXH4 (where M $$=$$= Na,Li and X $$=$$= Al,B)

The present paper reports the effect of B- and BN-doped \(\hbox {C}_{60}\) as catalysts for lowering the dehydrogenation energy in \(\hbox {MXH}_{4}\) clusters (M = Na and Li, X = Al and B) using density functional calculations. \(\hbox {MXH}_{4}\) interacts strongly with B-doped \(\hbox {C}_{60}\) and weakly with BN-doped \(\hbox {C}_{60}\) in comparison with pure \(\hbox {C}_{60}\) with binding energy 0.56–0.80 and 0.05–0.34 eV, respectively. The hydrogen release energy \((E_{\mathrm{HRE}})\) of \(\hbox {MXH}_{4}\) decreases sharply in the range of 38–49% when adsorbed on B-doped \(\hbox {C}_{60}\); however, with BN-doped \(\hbox {C}_{60}\) the decrease in the \(E_{\mathrm{HRE}}\) varies in the range of 6–20% as compared with pure \(\hbox {MXH}_{4}\) clusters. The hydrogen release energy of second hydrogen atom in \(\hbox {MXH}_{4}\) decreases sharply in the range of 1.7–41% for BN-doped \(\hbox {C}_{60}\) and decreases in the range of 0.2–11.3% for B-doped \(\hbox {C}_{60}\) as compared with pure \(\hbox {MXH}_{4}\) clusters. The results can be explained on the basis of charge transfer within \(\hbox {MXH}_{4}\) cluster and with the doped \(\hbox {C}_{60}\).     

$$\hbox {SiO}_{2}\hbox {/TiO}_{2}$$ multi-layered thin films with self-cleaning and enhanced optical properties

Self-cleaning, high transmittance glazing was obtained by cold spray deposition for glazings. The thin films contain \(\hbox {TiO}_{2}\), \(\hbox {SiO}_{2}\) and Au nanoparticles in different structures which allow for tailoring the optical, hydrophilic and photocatalytic properties. The crystallinity, morphology and surface energy were correlated with the optical transmittance and reflectance; the transmittance increased from 89.45 (for the glass substrate) to 91.76% when Au nanoparticles were used in the tandem layered structures. The samples containing alternating multi-layered \(\hbox {SiO}_{2}\) and \(\hbox {TiO}_{2}\) thin films without gold nanoparticles show hydrophilic surface; for these layers, the photocatalytic efficiency reaches 40% under simulated solar radiation. A conditioning effect based on adsorption was observed to increase the photocatalytic efficiency. These highly transparent coatings are well suited for glazings and fenestration, showing the self-cleaning effect based on combined superhydrophilicity and photocatalysis.     

Resistance-switching properties of Bi-doped $$\hbox {SrTiO}_{3}$$ films for non-volatile memory applications with different device structures

\(\hbox {SrTiO}_{3}\) and Bi-doped \(\hbox {SrTiO}_{3}\) films were fabricated with different device structures using the sol–gel method for non-volatile memory applications, and their resistance-switching behaviour, endurance and retention characteristics were investigated. \(\hbox {SrTiO}_{3}\) and \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt have the same phase structure, morphologies and grain size; however, the grain size of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si is slightly larger than those of the \(\hbox {SrTiO}_{3}\) films grown on Si and the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Pt. The \(\hbox {SrTiO}_{3}\) or \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt all exhibit bipolar resistive-switching behaviour and follow the same conductive mechanism; however, the \(\hbox {Ag}/\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}/\hbox {Si}\) device possesses the highest \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of \(10^{5}\) and the best endurance and retention characteristics. The doping of Bi is conducive to enhance the \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of the \(\hbox {SrTiO}_{3}\) films; meanwhile, the Si substrates help improve the endurance and retention characteristics of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films.     

Facile synthesis and characterization of rough surface $$\mathrm{V}_{2}\hbox {O}_{5}$$ nanomaterials for pseudo-supercapacitor electrode material with high capacitance

\(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials with rough surface were synthesized using commercial \(\hbox {V}_{2}\hbox {O}_{5}\), ethanol (EtOH) and \(\hbox {H}_{2}\hbox {O}\) as the starting materials by a simple hydrothermal route and combination of calcination. The electrochemical properties of \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials as electrodes in a supercapacitor device were measured using cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) method. \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials exhibit the specific capacitance of 423 F \(\hbox {g}^{-1}\) at the current density of 0.5 A \(\hbox {g}^{-1}\) and retain 327 F \(\hbox {g}^{-1}\) even at the high current density of 10 A \(\hbox {g}^{-1}\). The influence of the ratio of \(\hbox {EtOH/H}_{2}\hbox {O}\), the calcined time and temperature on the morphology, purity and electrochemical property of the products is discussed in detail. The results revealed that the ratio of \(\hbox {EtOH}\hbox {/}\hbox {H}_{2}\hbox {O}= 10\hbox {/}25\) and calcination at \(400{^{\circ }}\hbox {C}\) for 2–4 h are favourable for preparing \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials and they exhibited the best electrochemical property. The novel morphology and high specific surface area are the main factors that contribute to high electrochemical performance of \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials during the charge–discharge processes. It turns out that \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials with rough surface is an ideal material for supercapacitor electrode in the present work.     

A facile approach for the synthesis of porous $$\hbox {KTiNbO}_{5}$$ catalyst with good activity for hydrogenation of p-nitrophenol

Through simple ions exchange and hydrothermal reaction, the porous structure of \(\hbox {MnO}_{2}\)-pillared \(\hbox {KTiNbO}_{5}\) composites were synthesized. The fabricated porous structure makes \(\hbox {KTiNbO}_{5}\) as good absorbance property for methylthionine chloride (MB). Furthermore, the as-synthesized porous \(\hbox {KTiNbO}_{5}\) can perform photocatalytic degradation of MB with good effectivity. What’s more, after loading Au nanoparticles into it, a novel catalyst for catalytic hydrogenation of p-nitrophenol was obtained. The possible ‘layer-by-layer quilt expose’ mode of \(\hbox {Au-MnO}_{2}\hbox {-KTiNbO}_{5}\) composites for catalytic hydrogenation of p-nitrophenol was proposed.     

Structures and electronic properties of $$\hbox {W}_{m}\hbox {Cu}_{n}\,(n + m \le 7)$$ clusters

Geometric and electronic structures of \(\hbox {W}_{m}\hbox {Cu}_{n}\, (m + n \le 7)\) cluster have been systematically calculated by density functional theory at the generalized gradient approximation level for ground-state structures. \(\hbox {W}_{m}\hbox {Cu}_{n}\) clusters with \(n = 1, 3, 5\) tend to form bipyramid structures, whereas \(\hbox {WCu}_{n}\) favour planar shapes except for \(\hbox {WCu}_{5}\). The configurations of \(\hbox {W}_{m}\hbox {Cu}_{n}\) clusters are more sensitive to the Cu atoms than the W atoms, while the average atomic binding energies and the total magnetic moments are determined by W atoms. The calculated second-order differences in energies and HOMO–LOMO energy gaps show pronounced odd–even oscillating behaviours. From the Mulliken electron population analysis, we found that Cu 4p and W 6p orbitals exhibit electronic charges and both Cu 4s and W 6s orbitals transfer electronic charges to the W 5d orbital, which lead to the extension of W–Cu bond lengths.     

Interface engineering of $$\hbox {TiO}_{2}$$@PANI nanostructures for efficient visible-light activation

Core–shell-structured \(\hbox {TiO}_{2}\)@PANI composites were fabricated using negatively charged titanium glycolate (TG) precursor spheres, which were decorated using hydrochloric acid; subsequently, the uniform polyaniline (PANI) layer could be attached onto the surface of the polystyrene spheres by in situ chemical oxidative polymerization and finally, the resulting PANI-grafted TG were allowed to hydrolyse by treating the material with hot water. The TGs were transformed to porous \(\hbox {TiO}_{2}\), leading to the formation of core–shell \(\hbox {TiO}_{2}\)@PANI composites. The resulting \(\hbox {TiO}_{2}\)@PANI composite photocatalysts were characterized by X-ray diffraction, scanning electron microscopy, ultraviolet–visible diffuse reflection spectroscopy and photoluminescence spectroscopy. Significantly, the \(\hbox {TiO}_{2}\)@PANI composite photocatalysts exhibited dramatically enhanced photo-induced electron–hole separation efficiency, which was confirmed by the results of photocurrent measurements. PANI was dispersed uniformly over the porous \(\hbox {TiO}_{2}\) surface with an intimate electronic contact on the interface to act cooperatively to achieve enhanced photocatalytic properties, indicating that core–shell \(\hbox {TiO}_{2}\)@PANI composite photocatalysts could be promising candidate catalysts under visible-light irradiation. The mechanism of enhancing photocatalytic activity was proposed on the basis of the experimental results and estimated energy band positions.     

Effect of oxygen vacancies on Li-storage of anatase $$\hbox {TiO}_{2}$$ (001) facets: a first principles study

Effect of oxygen vacancies on Li-storage of anatase \(\hbox {TiO}_{2}\) (001) facets was stimulated by density functional theory (DFT). The lattice parameters, adsorbed energy and energy barriers of \(\hbox {TiO}_{2}\) with oxygen vacancies were calculated. High adsorption energy of 5.91 eV for Li atoms indicates that oxygen vacancies have a positive effect on the Li storage of nanostructured anatase \(\hbox {TiO}_{2}\). The theoretical capacity was enhanced by an extra Li atom storaged at the oxygen vacancies.     

Predicting $$\hbox {CO}_{2}$$ Solubility in Imidazole Ionic Liquids for Use in Absorption Refrigeration Systems by Using the Group Contribution Equation of State Method

Traditional absorption refrigeration such as \(\hbox {H}_{2}\hbox {O}\)–LiBr- and \(\hbox {NH}_{3}\)–\(\hbox {H}_{2}\hbox {O}\)-based refrigeration has limited applications because of several issues, including crystallization, corrosion, and large volume. \(\hbox {CO}_{2}\)–ionic liquids (ILs) as new absorption working pairs were investigated in this study. The objective was to use the group contribution equation of state (GC-EOS) method to predict the solubilities of binary systems containing high-pressure \(\hbox {CO}_{2}\)–imidazole bis(trifluoromethanesulfonimide) ILs and to investigate the applicability and accuracy of the GC-EOS model. The results showed that at pressures up to 11.0 MPa and temperatures of 273 K to 400 K, the \(\hbox {CO}_{2}\) solubility in the ILs increased with increasing system pressure but decreased with increasing temperature, and its variation rate was lower at higher pressures or temperatures. Also, \(\hbox {CO}_{2}\) solubility increased in the order of [emim][\(\hbox {Tf}_{2}\hbox {N}\)] < [bmim][\(\hbox {Tf}_{2}\hbox {N}\)] < [hmim][\(\hbox {Tf}_{2}\hbox {N}\)] < [omim][\(\hbox {Tf}_{2}\hbox {N}\)], indicating that longer alkyl chains of identical IL families resulted in higher \(\hbox {CO}_{2 }\) solubility. The model prediction of \(\hbox {CO}_{2}\) solubility in the four different ILs showed reasonable consistency with the corresponding experimental results from the literature; the largest deviation was 5.7 % for \(\hbox {CO}_{2}\)-[emim][\(\hbox {Tf}_{2}\hbox {N}\)]. Therefore, it can be concluded that the GC-EOS model is a promising theoretical solution that can be used to search for suitable \(\hbox {CO}_{2}\)–IL working pairs for absorption refrigeration systems.     

Synthesis,characterization and electrochemical performance of $$\hbox {Li}_{2}\hbox {Ni}_{x}\hbox {Fe}_{1-x}\hbox {SiO}_{4}$$ cathode materials for lithium ion batteries

\(\hbox {Li}_{2}\hbox {Ni}_{x}\hbox {Fe}_{1-x}\hbox {SiO}_{4}\) (\(x = 0\), 0.2, 0.4, 0.6, 0.8 and 1) samples were prepared by a sol–gel process. The crystal structure of prepared samples of \(\hbox {Li}_{2}\hbox {Ni}_{x}\hbox {Fe}_{1-x}\hbox {SiO}_{4}\) was characterized using an X-ray diffractometer. Different crystallographic parameters such as crystallite size and lattice cell parameters have been calculated. Scanning electron microscopy and Fourier transform infrared spectroscopy investigations were carried out, which reveal the morphology and function groups of the synthesized samples. Furthermore, electrochemical impedance spectra measurements are performed. The obtained results indicated that the highest conductivity is achieved for the \(\hbox {Li}_{2}\hbox {Ni}_{0.4}\hbox {Fe}_{0.6}\hbox {SiO}_{4}\) electrode compound. It was observed that Li–\(\hbox {Li}_{2}\hbox {Ni}_{0.4}\hbox {Fe}_{0.6}\hbox {SiO}_{4}\) battery has initial discharge capacity of 164 mAh \(\hbox {g}^{-1}\) at 0.1C rate. The cycle life performance of all \(\hbox {Li}_{2}\hbox {Ni}_{x}\hbox {Fe}_{1-x}\hbox {SiO}_{4}\) batteries ranged between 100 and 156 mAh \(\hbox {g}^{-1}\) with coulombic efficiency range between 70.9 and 93.9%.     

Elastic and thermodynamic properties of zirconium- and hafnium-doped $$\hbox {Rh}_{3}\hbox {V}$$ intermetallic compounds: potential aerospace material

Structural, electronic, mechanical and thermodynamic properties of \(\hbox {Rh}_{3}\hbox {Zr}_{x}\hbox {V}_{1-x}\) and \(\hbox {Rh}_{3}\hbox {Hf}_{x}\hbox {V}_{1-x}\) (\(x = 0\), 0.125, 0.25, 0.75, 0.875 and 1) combinations are investigated by means of first-principles calculations based on the density functional theory within the generalized gradient approximation. Here, \(\hbox {Rh}_{3}\hbox {V}\) is chosen as the parent binary compound and the doping elements are zirconium and hafnium with the above-mentioned concentrations. The calculated lattice parameters and elastic modulus of binary \(\hbox {Rh}_{3}\hbox {Hf}\), \(\hbox {Rh}_{3}\hbox {V}\) and \(\hbox {Rh}_{3}\hbox {Zr}\) are in good agreement with the available experimental and other theoretical results. In this study, the following ternary materials viz., \(\hbox {Rh}_{3}\hbox {Zr}_{0.75}\hbox {V}_{0.25}\), \(\hbox {Rh}_{3}\hbox {Hf}_{0.25}\hbox {V}_{0.75}\) and \(\hbox {Rh}_{3}\hbox {Hf}_{0.75}\hbox {V}_{0.25}\) are found to be brittle/more brittle than the parent binary compound \(\hbox {Rh}_{3}\hbox {V}\), whereas the other ternary combinations, namely \(\hbox {Rh}_{3}\hbox {Zr}_{0.125}\hbox {V}_{0.875}\), \(\hbox {Rh}_{3}\hbox {Zr}_{0.25}\hbox {V}_{0.75}\), \(\hbox {Rh}_{3}\hbox {Zr}_{0.875}\hbox {V}_{0.125}\), \(\hbox {Rh}_{3}\hbox {Hf}_{0.125}\hbox {V}_{0.875}\) and \(\hbox {Rh}_{3}\hbox {Hf}_{0.875}\hbox {V}_{0.125}\) are found to be more ductile than \(\hbox {Rh}_{3}\hbox {V}\). The more brittle ternary combination, namely \(\hbox {Rh}_{3}\hbox {Hf}_{0.75}\hbox {V}_{0.25}\) (\(B = 229.32\,\hbox {GPa}\)) has the maximum Young’s modulus, shear modulus and hardness values; whereas the more ductile ternary \(\hbox {Rh}_{3}\hbox {Zr}_{0.25}\hbox {V}_{0.75}\) combination (\(B = 243.54\,\hbox {GPa}\)) is found to have the least values of Young’s modulus, shear modulus and hardness. The band structure, density of states histograms and charge density plots are drawn and discussed. Computed Debye temperature (\(\theta _{\mathrm{D}}\)), Grüneisen parameter (\(\zeta \)) and melting temperature (\(T_{\mathrm{m}})\) of the parent binary compound \(\hbox {Rh}_{3}\hbox {V}\), the more brittle \(\hbox {Rh}_{3}\hbox {Hf}_{0.75}\hbox {V}_{0.25}\) combination and the more ductile \(\hbox {Rh}_{3}\hbox {Zr}_{0.25}\hbox {V}_{0.75}\) combination are given by (895 K, 1.3491, 2788 K), (790 K, 1.2701, 2736 K) and (698 K, 1.7972, 2529 K), respectively.     

Effect of annealing temperature and $$\hbox {CdCl}_{2}$$ treatment on the photo-conversion efficiency of $$\hbox {CdTe/Zn}_{0.1}$$CdTe/Zn0.1$$\hbox {Cd}_{0.9}$$Cd0.9S thin film solar cells

We report the effects of annealing in conjunction with \(\hbox {CdCl}_{2}\) treatment on the photovoltaic properties of \(\hbox {CdTe/Zn}_{0.1}\hbox {Cd}_{0.9}\)S thin film solar cells. CdTe layer is subjected to dry \(\hbox {CdCl}_{2}\) treatment by thermal evaporation method and subsequently, heat treated in air using a tube furnace from 400 to \(500{^{\circ }}\hbox {C}\). AFM and XRD results show improved grain size and crystallographic properties of the CdTe film with dry \(\hbox {CdCl}_{2}\) treatment. This recrystallization and grain growth of the CdTe layer upon \(\hbox {CdCl}_{2}\) treatment translates into improved photo-conversion efficiencies of \(\hbox {CdTe/Zn}_{0.1}\hbox {Cd}_{0.9}\)S cell. The results of dry \(\hbox {CdCl}_{2}\) treatment were compared with conventional wet \(\hbox {CdCl}_{2}\) treatment. Photo-conversion efficiency of 5.2% is achieved for dry \(\hbox {CdCl}_{2}\)-treated cells in comparison with 2.4% of wet-treated cell at heat treatment temperature of \(425{^{\circ }}\hbox {C}\).     

Radiative Properties of Ceramic $$\hbox {Al}_{2}\hbox {O}_{3}$$, AlN,and $$\hbox {Si}_{3}\hbox {N}_{4}$$Si3N4: I. Experiments

The radiative properties of dense ceramic \(\hbox {Al}_{2}\hbox {O}_{3}\), AlN, and \(\hbox {Si}_{3}\hbox {N}_{4}\) plates are investigated from the visible to the mid-infrared region at room temperature. Each specimen has different surface finishings on different sides of the laminate. A monochromator was used with an integrating sphere to measure the directional-hemispherical reflectance and transmittance of these samples at wavelengths from 0.4 \(\upmu \hbox {m}\) to 1.8 \(\upmu \hbox {m}\). The specular reflectance was obtained by a subtraction technique. A Fourier-transform infrared spectrometer was used to measure the directional-hemispherical or specular reflectance and transmittance with appropriate accessories from about 1.6 \(\upmu \hbox {m}\) to 19 \(\upmu \hbox {m}\). All measurements were performed at near-normal incidence on either the smooth side or the rough side of the sample. The experimental observations are qualitatively interpreted considering the optical constants, surface roughness, and volume scattering and absorption.     

High-pressure studies of superconductivity in $$\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}$$

\(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\) crystallizes in tetragonal CeOBiS\(_{2}\) structure (S. G. P4/nmm). We have investigated the effect of pressure on magnetization measurements. Our studies suggest improved superconducting properties in polycrystalline samples of \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\). The \(T_{\mathrm{c}}\) in our sample is 5.3 K, at ambient pressure, which is marginal but definite enhancement over \(T_{\mathrm{c}}\) reported earlier (= 5.1 K). The upper critical field \(H_{\mathrm{c}2}\)(0) is greater than 3 T, which is higher than earlier report on this material. As determined from the M–H curve, both \(H_{\mathrm{c}2}\) and \(H_{\mathrm{c}1}\) decrease under external pressure P (0 \(\le P \le \) 1 GPa). We observe a decrease in critical current density and transition temperature on applying pressure in \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\).     

Role of reactive species in the photocatalytic degradation of amaranth by highly active N-doped $$\mathbf{WO}_{\mathbf{3}}$$

A novel, highly visible light active N-doped \(\hbox {WO}_{3}\) (\(\hbox {N}\)-\(\hbox {WO}_{3})\) is successfully synthesized via thermal decomposition of peroxotungstic acid–urea complex. The photocatalytic activity of \(\hbox {N}\)-\(\hbox {WO}_{3}\) is evaluated for the degradation of amaranth (AM) dye under visible and UVA light along with the role of reactive species, which has not yet been studied for \(\hbox {N}\)-\(\hbox {WO}_{3}\) photocatalysts. Doping of N into substitutional and interstitial sites of \(\hbox {WO}_{3}\) is confirmed by X-ray photoelectron spectroscopy and X-ray absorption near-edge spectroscopy. At a pH of 7, 1 g \(\hbox {l}^{-1}\) of \(\hbox {N}\)-\(\hbox {WO}_{3}\) can completely degrade \(10\,\hbox {mg } \hbox {l}^{-1}\) of AM within 1 h under visible and UVA light. For the degradation of AM by \(\hbox {N}\)-\(\hbox {WO}_{3}\) under visible and UVA light, \(\hbox {h}^{+}\) is found to be the main reactive species, while \(\cdot \hbox {OH}\) contributes to a lesser extent. On the contrary, \(^{1}\hbox {O}_{2}, \cdot \hbox {O}_{2}^{-}\) and \(\hbox {e}^{-}\) show negligible roles. The crucial role of \(\hbox {h}^{+}\) indicates effective suppression of electron–hole recombination after N doping. Dye sensitization and oxidation by reactive species are found to be the major pathway for the degradation of AM under visible and UVA light, respectively.     

Superconducting epitaxial $$\hbox {YBa}_{2}\hbox {Cu}_{3}\hbox {O}_{7-\delta }$$ on $$\hbox {SrTiO}_{3}$$SrTiO3-buffered Si(001)

Thin films of optimally doped(001)-oriented \(\hbox {YBa}_{2}\hbox {Cu}_{3}\hbox {O}_{7-\updelta }\) are epitaxially integrated on silicon(001) through growth on a single crystalline \(\hbox {SrTiO}_{3}\) buffer. The former is grown using pulsed-laser deposition and the latter is grown on Si using oxide molecular beam epitaxy. The single crystal nature of the \(\hbox {SrTiO}_{3}\) buffer enables high quality \(\hbox {YBa}_{2}\hbox {Cu}_{3}\hbox {O}_{7-\updelta }\) films exhibiting high transition temperatures to be integrated on Si. For a 30-nm thick \(\hbox {SrTiO}_{3}\) buffer, 50-nm thick \(\hbox {YBa}_{2}\hbox {Cu}_{3}\hbox {O}_{7-\updelta }\) films that exhibit a transition temperature of \(\sim \)93 K, and a narrow transition width (<5 K) are achieved. The integration of single crystalline \(\hbox {YBa}_{2}\hbox {Cu}_{3}\hbox {O}_{7-\updelta }\) on Si(001) paves the way for the potential exploration of cuprate materials in a variety of applications.     

$$\hbox {NO}_{2}^{-}$$ and $$\hbox {SCN}^{-}$$SCN--intercalated layered double hydroxides: structure and orientation of anions in the interlayer gallery

\(\hbox {NO}_{2}^{-}\) and \(\hbox {SCN}^{-}\) are two common small inorganic anions. The former is a common industrial pollutant. The latter is linear and is a good mimic for the toxic \(\hbox {CN}^{-}\) ion. The structures of these two anions are refined within the gallery of the [Zn–Al]-layered double hydroxide (LDH). Both LDHs crystallize as mixed anion phases. The nitrite is found to co-exist with the nitrate ion. The nitrite ion is intercalated with its molecular plane inclined to the metal hydroxide layer. In the case of the \(\hbox {SCN}^{-}\) intercalated LDH, no other anion was detected by ion chromatography, suggesting that the \(\hbox {SCN}^{-}\) deficiency is compensated by intercalated hydroxyl ions. In this case, the \(\hbox {SCN}^{-}\) ion is found to be intercalated with its molecular axis inclined to the metal hydroxide layer.     

Evaluation of the elastic properties of monovalent oxides using $$\hbox {TeO}_{2}$$-based glasses

Quaternary tellurite glasses with composition \(75\hbox {TeO}_{2}\)–\(5\hbox {WO}_{3}\)–\(15\hbox {Nb}_{2} \hbox {O}_{5}\)–\(5\hbox {M}_{x} \hbox {O}_{y}\) in mol%, where \(\hbox {M}_{x}\hbox {O}_{y}\) = (\(\hbox {Na}_{2}\hbox {O}, \, \hbox {Ag}_{2}\hbox {O}\), ZnO, MgO, CuO, NiO, \(\hbox {TiO}_{2}\), \(\hbox {MnO}_{2}\)), were prepared by the normal melt-quenching method. The ultrasonic velocities (longitudinal and shear) were measured in these glasses using the pulse-echo technique at room temperature. Their elastic moduli, microhardness and Debye temperature were calculated and discussed in terms of the modifier’s ionicity and quantitatively in terms of number of bonds per unit volume and the cross-link density. In this study, the values of ultrasonic velocities, elastic moduli, Debye temperature and microhardness were found to be strongly dependent on three factors, namely: (i) modifier’s ionicity; (ii) trigonal pyramid (\(\hbox {TeO}_{3}\))/trigonal bipyramid (\(\hbox {TeO}_{4}\)) ratio; and (iii) glass transition temperature \(T_\mathrm{g}\). We used the Makishima and Mackenzie’s model to calculate the theoretical elastic moduli and to indicate that the experimental values were in good agreement with the theoretical values.     

Distribution of relaxation times investigation of $$\hbox {Co}^{3+}$$ doping lithium-rich cathode material $$\hbox {Li}[\hbox {Li}_{0.2} \hbox {Ni}_{0.1} \hbox {Mn}_{0.5} \hbox {Co}_{0.2}]\hbox {O}_{2}$$Li[Li0.2Ni0.1Mn0.5Co0.2]O2

The element \(\hbox {Co}^{3+}\) was introduced into lithium-rich material \(0.5\hbox {Li}_{2}\hbox {MnO}_{3} \cdot 0.5 \hbox {LiNi}_{0.5}\hbox {Mn}_{0.5}\hbox {O}_{2}\) by a polyacrylamide-assisted sol–gel method to form \(\hbox {Li}[\hbox {Li}_{0.2} \hbox {Ni}_{0.1} \hbox {Mn}_{0.5} \hbox {Co}_{0.2}]\hbox {O}_{2}\) and better electro-chemical performances were observed. Electrochemical impedance spectroscopy spectra were measured on 11 specific open circuit voltage levels on the initial charge profile. Then they were converted to the distribution of relaxation times (DRTs) g(\(\tau \)) by self-consistent Tikhonov regularization method. The obtained DRTs offered a higher resolution in the frequency domain and provided the number and the physical origins of loss processes clearly. Through the analysis of DRTs, the rapid augmentation of resistance to electronic conduction and charge transfer within the voltage range 4.46–4.7 V where the removal of \(\hbox {Li}_{2}\hbox {O}\) from \(\hbox {Li}_{2} \hbox {MnO}_{3}\) component took place was the most remarkable phenomenon and the \(\hbox {Co}^{3+}\) doping greatly reduced the resistance to electronic conduction Re. This gave us more evidence about the complicated ‘structurally integrated’ composite character of the material.